According to Section 2.4.4 of the Synaptics TouchPad Interfacing
Guide, bit 2 specifies if multi-finger detection is provided by
the touchpad. Thus, only set BTN_TOOL_DOUBLETAP and
BTN_TOOL_TRIPLETAP if the device actually supports it.
Signed-off-by: NPeter Hutterer <peter.hutterer@redhat.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NPeter Popovec <popovec@fei.tuke.sk>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

There've been reports [1] about the sysem bell causing a hard
lockup.  My machine was affected as well: any speaker output hung
the machine completely, nothing in the logs, no magic sysrq,
etc., looked like a hardware problem.  Had a closer look on the
issue, and it turned out that the pcspkr module is responsible.
The cause is the bad setup of Timer 2 in the i8253 controller,
which probably hangs the whole PIT controller.

Intel datasheets [2] state that the timer registers are in an
undefined state after reset and they need to be programmed before
enabling the timer. (And enabling without programming the
frequency first doesn't make sense anyway).

I don't know which chipsets are affected (if not all), it also
depends on the BIOS whether it initializes the timer (e.g. to
beep when you start the machine).

The following patch solved the issue on my ICH6 notebook,
couldn't test it with any others, but should be safe to apply.

[1]
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/146151
https://bugs.launchpad.net/ubuntu/+bug/270790
http://ubuntuforums.org/showthread.php?t=227693
http://bugs.gentoo.org/show_bug.cgi?id=222583
https://bugzilla.redhat.com/show_bug.cgi?id=454225

[2]
http://www.intel.com/assets/pdf/datasheet/252516.pdf
http://www.intel.com/assets/pdf/datasheet/301473.pdf
http://www.intel.com/design/chipsets/datashts/29065503.pdfSigned-off-by: NZoltan Devai <zdevai@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The usbtouchscreen module implements a driver for the TSC-10 DM USB
touchscreen controllers, but assumes a 2-byte response for the
CMD_RESET and CMD_RATE commands, when they can be only a single byte
when no EEPROM is connected.

The driver worked with an earlier controller revision, but new
revisions of the controller fail.

It seems the problem is that the early controller had the
SEL4/EEPROM-CS pin high, but the new controller has it down, making
the response different.

Without the fix, the controller would answer the single byte 0x06
(ACK), making the init fail with -ENODEV because buf[1] is 0xFF (as
initialized before).

As the single byte is the only thing we need to check it was ok, there
is no need to verify the second byte.

The [0x15 0x01] case is the NAK [0x15] response for when there is no
data in the EEPROM [bit-0 of second byte set], so I let that be, as I
don't have any controller with an EEPROM.

With this patch, both the earlier and latest controller work the same.

Note: This was previously submited as BUG #11961 [1] on the bugzilla
tracker, but rebased to version 2.6.27.4 and with unnecessary comments
and printk's removed.

[1] http://bugzilla.kernel.org/show_bug.cgi?id=11961Signed-off-by: NNuno Lucas <ntlucas@gmail.com>
Acked-by: NDaniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

There is no reason to limit the GPIO rows to 6 for OMAP2.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The GPIO interrupts are disabled several times after the first key press.
No need to disable - again - the interrupts in the omap_kp_scan_keypad
function on OMAP2.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The appletouch driver has grown up from supporting only a couple of
touchpads into supporting many touchpads, which can have different
number of sensors, different aspect ratios etc.

This patch cleans up the current driver code and makes it easy to
support the features of each different touchpad.

As a side effect, this patch also modifies the 'Y' multiplication factor
of the 'geyser3' and 'geyser4' touchpads (found on Core Duo and Core2
Duo MacBook and MacBook Pro laptops) in order to make the touchpad
output match the aspect ratio of the touchpad (Y factor changed from 43
to 64).

[dtor@mail.ru: make atp_info constant]
Signed-off-by: NStelian Pop <stelian@popies.net>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This patch adds a flag to gpio-key driver to turn on the input subsystems
auto repeat feature if needed.
Signed-off-by: NDominic Curran <dcurran@ti.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Review comments were incorporated to improve the driver.

1. Some data was eliminated that was not needed.
2. Renaming of variables for clarity.
3. Removed unneeded type casting.
4. Changed to use dev_err rather than other I/O.
5. Merged together some functions.
6. Added kerneldoc format to functions.
Signed-off-by: NSadanand <sadanan@xilinx.com>
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Currently, evdev has working 32bit compatibility and uinput does not. uinput
needs the input_event code that evdev uses, so let's refactor it so it can
be shared.

[dtor@mail.ru: add fix for force feedback compat issues]
Signed-off-by: NPhilip Langdale <philipl@overt.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The SGI Volume Button interface driver uses GPL-only symbols
platform_driver_unregister and platform_driver_register, but
lacks license specification. Thus, when compiled as a module,
this driver cannot be installed. This patch fixes this by
adding the MODULE_LICENSE() specification.
Signed-off-by: NDmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Separate building of corgi_ssp.c, and introduce a new hidden config option
CONFIG_CORGI_SSP_DEPRECATED for this. Aslo mark corgi_ts.c and corgi_bl.c
as deprecated.

This unbreaks the legacy configs in {corgi,spitz}_defconfig, however, SPI
based ADS7846 touchscreen driver and a new SPI-based corgi_lcd.c driver
with integrated backlight support are recommended.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NSamuel Ortiz <sameo@openedhand.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible.  In the
few places that will not work out, use a basic printk().

Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is version 5 of the driver. Relative mode support has been
dropped (users wishing to use touchpad in relative mode can use
standard PS/2 protocol emulation done in hardware). The driver
supports both original version of Elantech protocol and the newer
one used by touchpads installed in EeePC.
Signed-off-by: NArjan Opmeer <arjan@opmeer.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NStefan Bader <stefan.bader@canonical.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This updates most of the OMAP drivers which are in mainline to switch to
using the cross-platform GPIO calls instead of the older OMAP-specific
ones.

This is all fairly brainless/obvious stuff.  Probably the most interesting
bit is to observe that the omap-keypad code seems to now have a portable
core that could work with non-OMAP matrix keypads.  (That would improve
with hardware IRQ debouncing enabled, of course...)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Kill compiler warnings related to printf() formats in the input drivers for
various HP9000 machines, which are shared between PA-RISC (suseconds_t is int)
and m68k (suseconds_t is long). As both are 32-bit, it's safe to cast to int.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This updates the email address for Liam Girdwood as my old address is no
longer valid.
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Thinkpad R31 needs i8042 nomux quirk.  Stops jittery jumping mouse
and random keyboard input. Fixes kernel bug #11723.  Cherry picked
from Ubuntu who have sometimes (on-again-off-again) had a fix in
their patched kernels.
Signed-off-by: NColin B Macdonald <cbm@m.fsf.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The map_to_7segment.h provides generic 7segment LED mappings and is
designed to be used by other drivers.  Moving it to common area will
make it more usable.  Also exporting it to userspace will help users
of sysfs interface.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: NHenk Vergonet <henk.vergonet@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

We had a report a while back that the ads7846 driver had some issues
when used with DMA-based SPI controllers (like atmel_spi) on systems
where main memory is not DMA-coherent (most non-x86 boards). Allocate
memory potentially used for DMA separately to avoid cache line issues.
Reported-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Recent conversion from err(), warn(), info() to dev_* variants caused loss
of newlines at the end of messages, add them back.
Signed-off-by: NDaniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms and we want to get rid of CONFIG_PPC_MERGE use
CONFIG_PPC instead.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This adds support for OLPC's touchpad.  It has lots of neat features,
none of which are enabled because the hardware is too buggy.  Instead,
we use it like a normal touchpad, but with a number of workarounds in
place to deal with the frequent hardware spasms.  Humidity changes,
sweat, tinfoil underwear, plugging in AC, drinks, evil felines.. All
tend to cause the touchpad to freak out.
Signed-off-by: NAndres Salomon <dilinger@debian.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

We want to support attr->set callbacks that may need psmouse->state to
not be updated, or may want to manually deal w/ enabling and disabling
the device.  To do that, we create __PSMOUSE_DEFINE_ATTR which enables
us to set a 'protect' argument specifying whether or not the set
callback should be protected with psmouse_disable and state setting.
Signed-off-by: NAndres Salomon <dilinger@debian.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

psmouse_queue_work is passed a delayed_work struct, and queues up the work
with kpsmouse_wq.  Since we're dealing with delayed_work stuff, this
also switches resync_work to a delayed_work struct as well, and makes
use of psmouse_queue_work when doing a resync within psmouse-base.
Signed-off-by: NAndres Salomon <dilinger@debian.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NAndres Salomon <dilinger@debian.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The GPIO connected to ADS7846 nPENIRQ signal is usually used to get
the pendown state as well. Introduce a .gpio_pendown, and use this
to decide the pendown state if .get_pendown_state is NULL.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This patch removes the usage of LONG() which is deprecated; we also
replace BIT() with BIT_MASK().
signed-off-by: NKristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Staying in multi-touch mode after closing the device sometimes makes
the keyboard drop keys or repeat keys irratically. The conjecture is
that some internal buffer starts to overflow, resulting in undefined
behavior. Switching back to normal mode when closing the device makes
the problem go away.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The GPIO connected to ADS7846 nPENIRQ signal is usually used to get
the pendown state as well. Introduce a .gpio_pendown, and use this
to decide the pendown state if .get_pendown_state is NULL.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NElvis Pranskevichus <el@prans.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

serio_raw only binds to non-translated devices. Enable serio_raw to
bind to normal (translated) keyboards which can have non-standard
extensions (like POS Keyboards). With this it is possible to send
commands to the device over /dev/serio_raw<n>.
Signed-off-by: NNiels de Vos <niels.devos@wincor-nixdorf.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

err(), warn(), info() are being removed in favor of dev_* variants.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>