Xen's PV network protocol includes messages to add/remove ethernet
multicast addresses to/from a filter list in the backend. This allows
the frontend to request the backend only forward multicast packets
which are of interest thus preventing unnecessary noise on the shared
ring.

The canonical netif header in git://xenbits.xen.org/xen.git specifies
the message format (two more XEN_NETIF_EXTRA_TYPEs) so the minimal
necessary changes have been pulled into include/xen/interface/io/netif.h.

To prevent the frontend from extending the multicast filter list
arbitrarily a limit (XEN_NETBK_MCAST_MAX) has been set to 64 entries.
This limit is not specified by the protocol and so may change in future.
If the limit is reached then the next XEN_NETIF_EXTRA_TYPE_MCAST_ADD
sent by the frontend will be failed with NETIF_RSP_ERROR.
Signed-off-by: NPaul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit a5597008 ("phy: fixed_phy: Add gpio to determine link up/down.")
added a new argument to fixed_phy_register(), but missed to update bgmac
driver, causing the following build failure:

drivers/net/ethernet/broadcom/bgmac.c:1450:2: error: too few arguments to function 'fixed_phy_register'

Add the missing argument.
Reported-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Resolve warnings resulting from redundant initialization of the
get_bus_info field in the mac_ops_X550* structures.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When unbinding an SR-IOV device with VFs configured from ixgbe, the
driver behaves in one of two ways.  If max_vfs was specified, the
SR-IOV state is disabled, removing the VFs.  The occurs regardless of
whether the VF count was later modified through sysfs.  If however
max_vfs is zero, such as by not specifying the module parameter, the
VFs persist after the PF is unbound from ixgbe.  If the PF is then
bound to vfio-pci to be assigned to a VM, the PF is non-functional.

>From the comment, commit da36b647 ("ixgbe: Implement PCI SR-IOV
sysfs callback operation") clearly intended this alternate behavior,
but probably didn't realize the PF doesn't work in this mode.

This bimodal behavior is confusing to users and results in a state
where the PF is broken for other uses unless the user sets
sriov_numvfs to zero prior to unbinding the device.  Remove this
behavior so that VFs are removed and the PF is functional for other
uses after unbind, regardless of the way VFs are enabled.
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now that we can do 2.5G link speed, we need to be able to report it.
Also change the nested triadic involved in creating the log message
to instead use a simpler switch statement to set a string pointer.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch resolves an issue where users were not able to dynamically
set number of queues for 82598 via ethtool -L
Reported-by: NTal Abudi <talabudi@gmail.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Allows to change the rxfh indirection table and/or key using
ethtool interface.
Signed-off-by: NTom Barbette <tom.barbette@ulg.ac.be>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Avoid a needless PHY access on copper phys to save the 10ms wait
time for each PHY access. A helper function is introduced to
actually do the register access and process the contents.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We already cache this FW/SW semaphore mask so might as well use it
for consistency.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes the redundant lan_id in the phy struct and uses
the bus version.  Both variables exist and intend to represent the
STATUS register LAN_ID field.  However, phy.lan_id is not bit shifted
so the phy.lan_id = 0x0 for LAN Id 0 and phy.lan_id = 0x4 for LAN Id 1.
Where bus.lan_id is bit shifted so bus.lan_id = 0x0 for LAN Id 0 and
bus.lan_id = 0x1 for LAN Id 1. There seems no need for the additional
lan_id variable and this should make the code less confusing.
Signed-off-by: NDonald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use kzalloc rather than kcalloc(1..

The semantic patch that makes this change is as follows:

// <smpl>
@@
@@

- kcalloc(1,
+ kzalloc(
          ...)
// </smpl>

and removing checkpatch below CHECK:
CHECK: Prefer kzalloc(sizeof(*fwd_adapter)...) over
kzalloc(sizeof(struct ixgbe_fwd_adapter)...)
Signed-off-by: NManinder Singh <maninder1.s@samsung.com>
Reviewed-by: NVaneet Narang <v.narang@samsung.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ixgbe never has as very doubtfully ever will support either
PCI or PCI-X devices.  So remove the unused types from the
ixgbe_bus_type.  Thanks to Alex Duyck for suggesting this.
Signed-off-by: NDonald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With this patch we add support for a new bus type ixgbe_bus_type_internal.
X550em devices use IOSF and not PCIe bus so this new type is to accommodate
them.
Signed-off-by: NDonald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Added ixgbe_get_bus_info_X550em to X550 code. ixgbe_get_bus_info_X550em
sets bus.width to ixgbe_bus_width_unknown and bus.speed to
ixgbe_bus_speed_unknown, because IOSF does not report a PCIe bus
width or speed.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the device is closing or suspending, call ixgbe_enter_lplu to
enter low power link up state on devices that support it. When this
is done, prevent the phy from being reset in the ixgbe_down path
so that link is present when calling ixgbe_enter_lplu.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for VXLAN RX offloads for the X55x devices that support
them.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

By using GSO for UDP-encapsulated packets, all ixgbe devices can
be directed to generate checksums for the inner headers because
the outer UDP checksum can be zero. So point the machinery at the
inner headers and have the hardware generate the checksum.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Wait up to about 100 us for FDIRCMD writes to complete and return
failure indications.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are various reasons why this method may or may not need to be
defined and some of these we don't know until runtime.  So we will
set the value in get_invariants.
Signed-off-by: NDonald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a support function that will indicate for the
existence of management FW.
Signed-off-by: NDonald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This fixes bugs where the port is not receiving multicast or VLAN tagged
packets when in promiscuous mode. This can occur when a SW bridge is
created on top of the device.

This also fixes issues where the promiscuous behavior setting was not
being preserved across a reset caused by features being enabled or
disabled.

We are using defport instead of doing a true promiscuous mode because we do
not need to receive the SRIOV or VMDq VSI directed traffic which would suck
up bandwidth and is really not intended for the SW bridge.

In addition, with defport we get VLAN promiscuous behavior which is not
possible from the VSI level promiscuous setting.

Change-ID: Ie21985eac32d5af1c02e9d71c6430a90d5bab40f
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The flags argument will allow control of the dissection process (for
instance whether to parse beyond L3).
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The temperature registers appear to report values in degrees Celsius
while the hwmon API mandates values to be exposed in millidegrees
Celsius. Do the conversion so that the values reported by "sensors"
are correct.

Fixes: aed93e0b ("tg3: Add hwmon support for temperature")
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: stable@vger.kernel.org [v3.6+]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 8b63ec18 ("phylib: Make PHYs children of their MDIO bus, not
the bus' parent.") uncovered a problem in mdiobus_unregister() which
leads to this warning when I reboot an APM Mustang (arm64) platform:

  WARNING: CPU: 7 PID: 4239 at fs/sysfs/group.c:224 sysfs_remove_group+0xa0/0xa4()
  sysfs group fffffe0000e07a10 not found for kobject 'xgene-mii-eth0:03'
  ...
  CPU: 7 PID: 4239 Comm: reboot Tainted: G            E   4.2.0-0.18.el7.test15.aarch64 #1
  Hardware name: AppliedMicro Mustang/Mustang, BIOS 1.1.0 Aug 26 2015
  Call Trace:
  [<fffffe000009739c>] dump_backtrace+0x0/0x170
  [<fffffe000009752c>] show_stack+0x20/0x2c
  [<fffffe00007436f0>] dump_stack+0x78/0x9c
  [<fffffe00000c2cb4>] warn_slowpath_common+0xa0/0xd8
  [<fffffe00000c2d60>] warn_slowpath_fmt+0x74/0x88
  [<fffffe0000293d3c>] sysfs_remove_group+0x9c/0xa4
  [<fffffe00004a8bac>] dpm_sysfs_remove+0x5c/0x70
  [<fffffe000049b388>] device_del+0x44/0x208
  [<fffffe000049b578>] device_unregister+0x2c/0x7c
  [<fffffe000050dc68>] mdiobus_unregister+0x48/0x94
  [<fffffe000052afd0>] xgene_enet_mdio_remove+0x28/0x44
  [<fffffe000052d3f0>] xgene_enet_remove+0xd0/0xd8
  [<fffffe000052d424>] xgene_enet_shutdown+0x2c/0x3c
  [<fffffe00004a204c>] platform_drv_shutdown+0x24/0x40
  [<fffffe000049d4f4>] device_shutdown+0xf0/0x1b4
  [<fffffe00000e31ec>] kernel_restart_prepare+0x40/0x4c
  [<fffffe00000e32f8>] kernel_restart+0x1c/0x80
  [<fffffe00000e3670>] SyS_reboot+0x17c/0x250

The problem is that mdiobus_unregister() deletes the bus device before
unregistering the phy devices on the bus. This wasn't a problem before
because the phys were not children of the bus:

  /sys/devices/platform/APMC0D05:00/net/eth0/xgene-mii-eth0:03
  /sys/devices/platform/APMC0D05:00/net/eth0/xgene-mii-eth0

But now that they are:

  /sys/devices/platform/APMC0D05:00/net/eth0/xgene-mii-eth0/xgene-mii-eth0:03

when mdiobus_unregister deletes the bus device, the phy subdirs are
removed from sysfs also. So when the phys are unregistered afterward,
we get the warning. This patch changes the order so that phys are
unregistered before the bus device is deleted.

Fixes: 8b63ec18 ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.")
Signed-off-by: NMark Salter <msalter@redhat.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NMark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Other Sierra Wireless MC73xx devices exist, with different USB IDs.

Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid Ward <david.ward@ll.mit.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

What features a phy supports is masked in genphy_config_init() by
looking at the PHYs BMSR register.

If the link is down, fixed_phy_update_regs() will only set the auto-
negotiation capable bit in BMSR. Thus genphy_config_init() comes to
the conclusion the PHY can only perform 10/Half, and masks out the
higher speed features. If however the link it up, BMSR is set to
indicate the speed the PHY is capable of auto-negotiating, and
genphy_config_init() does not mask out the high speed features.

To fix this, when the link is down, have fixed_phy_update_regs() leave
the link status, auto-negotiation complete, and link partner
capabilities unset, but set all the local capabilities depending on
the fixed phy speed.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An SFP module may have a link up/down status pin which can be
connection to a GPIO line of the host. Add support for reading such an
GPIO in the fixed_phy driver.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When polling for link status, don't consider ports which have a forced
link. Such ports don't monitor their phy or may not even have a phy.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some Marvell switches allow the RGMII Rx and Tx clock to be delayed
when the port is using RGMII. Have the adjust_link function look at
the phy interface type and enable this delay as requested.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the supported field of the phydev to indicate the speed features
of the phy. If the phy is never attached to a netdev, but used in an
adjust_link() function, the speed will be incorrectly evaluated to
10/half rather than the correct speed/duplex.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code sets user ports to perform auto negotiation using the
phy. CPU and DSA ports are configured to full duplex and maximum speed
the switch supports.

There are however use cases where the CPU has a slower port, and when
user ports have SFP modules with fixed speed. In these cases, port
settings to be read from a fixed_phy devices. The switch driver then
needs to implement the adjust_link op, so the port settings can be
set.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some Ethernet MAC drivers using the PHY library require the hardcoding
of link parameters when interfaced to a switch device, SFP module,
switch to switch port, etc. This has typically lead to various ad-hoc
implementations looking like this:

- using a "fixed PHY" emulated device, which will provide link
  indication towards the Ethernet MAC driver and hardware

- pretend there is no PHY and hardcode link parameters, ala mv643x_eth

Based on that, it is desireable to have the PHY drivers advertise the
correct link parameters, just like regular Ethernet PHYs towards their
CPU Ethernet MAC drivers, however, Ethernet MAC drivers should be able
to tell whether this link should be monitored or not. In the context
of an Ethernet switch, SFP module, switch to switch link, we do not
need to monitor this link since it should be always up.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently tun-info options pointer is used in few cases to
pass options around. But tunnel options can be accessed using
ip_tunnel_info_opts() API without using the pointer. Following
patch removes the redundant pointer and consistently make use
of API.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Reviewed-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support for setting VF's corresponding BGX LMAC in internal
loopback mode. This mode can be used for verifying basic HW
functionality such as packet I/O, RX checksum validation,
CQ/RBDR interrupts, stats e.t.c. Useful when DUT has no external
network connectivity.

'loopback' mode can be enabled or disabled via ethtool.

Note: This feature is not supported when no of VFs enabled are
morethan no of physical interfaces i.e active BGX LMACs
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for handling multiple qsets assigned to a
single VF. There by increasing no of queues from earlier 8 to max
no of CPUs in the system i.e 48 queues on a single node and 96 on
dual node system. User doesn't have option to assign which Qsets/VFs
 to be merged. Upon request from VF, PF assigns next free Qsets as
secondary qsets. To maintain current behavior no of queues is kept
to 8 by default which can be increased via ethtool.

If user wants to unbind NICVF driver from a secondary Qset then it
should be done after tearing down primary VF's interface.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: NRobert Richter <rrichter@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rework interrupt handler to avoid checking IRQ affinity of
CQ interrupts. Now separate handlers are registered for each IRQ
including RBDR. Register interrupt handlers for only those
which are being used. Add nicvf_dump_intr_status() and use it
in irq handlers.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch configures HW to strip 802.1Q header if found in a
receiving packet. The stripped VLAN ID and TCI information is
passed on to software via CQE_RX. Also sets netdev's 'vlan_features'
so that other HW offload features can be used for tagged packets.

This offload feature can be enabled or disabled via ethtool.

Network stack normally ignores RPS for 802.1Q packets and hence low
throughput. With this offload enabled throughput for tagged packets
will be almost same as normal packets.

Note: This patch doesn't enable HW VLAN insertion for transmit packets.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding support for receive hashing HW offload by using RSS_ALG
and RSS_TAG fields of CQE_RX descriptor. Also removed dependency
on minimum receive queue count to configure RSS so that hash is
always generated.

This hash is used by RPS logic to distribute flows across multiple
CPUs. Offload can be disabled via ethtool.
Signed-off-by: NRobert Richter <rrichter@cavium.com>
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the nicvf_send_msg_to_pf() function in the mailbox code.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NRobert Richter <rrichter@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added ethtool support to dump receive packet error statistics reported
in CQE. Also made some small fixes
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>