An Open-Channel SSD shall be initialized before use. To initialize, we
define an on-disk format, that keeps a small set of metadata to bring up
the media manager on top of the device.

The initial step is introduced to allow a user to format the disks for a
given media manager. During format, a system block is stored on one to
three separate luns on the device. Each lun has the system block
duplicated. During initialization, the system block can be retrieved and
the appropriate media manager can initialized.

The on-disk format currently covers (struct nvm_system_block):

 - Magic value "NVMS".
 - Monotonic increasing sequence number.
 - The physical block erase count.
 - Version of the system block format.
 - Media manager type.
 - Media manager superblock physical address.

The interface provides three functions to manage the system block:

 int nvm_init_sysblock(struct nvm_dev *, struct nvm_sb_info *)
 int nvm_get_sysblock(struct nvm *dev, struct nvm_sb_info *)
 int nvm_update_sysblock(struct nvm *dev, struct nvm_sb_info *)

Each implement a part of the logic to manage the system block. The
initialization creates the first system blocks and mark them on the
device. Get retrieves the latest system block by scanning all pages in
the associated system blocks. The update sysblock writes new metadata
and allocates new block if necessary.
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

NAND MLC memories have both lower and upper pages. When programming,
both of these must be written, before data can be read. However,
these lower and upper pages might not placed at even and odd flash
pages, but can be skipped. Therefore each flash memory has its lower
pages defined, which can then be used when programming and to know when
padding are necessary.

This patch implements the lower page definition in the specification,
and exposes it through a simple lookup table at dev->lptbl.
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Some flash media has extended capabilities, such as programming SLC
pages on MLC/TLC flash, erase/program suspend, scramble and encryption.
MCCAP is introduced to detect support for these capabilities in the
command set.
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

LightNVM targets need to know the state of the flash block when doing
flash optimizations. An example is implementing a write buffer to
respect the flash page size. Currently, block state is not accounted
for; the media manager only differentiates among free, bad and in-use
blocks.

This patch adds the logic in the generic media manager to enable
targets manage blocks into open and close separately, and it implements
such management in rrpc. It also adds a set of flags to describe the
state of the block (open, closed, free, bad).

In order to avoid taking two locks (nvm_lun and rrpc_lun) consecutively,
we introduce lockless get_/put_block primitives so that the open and
close list locks and future common logic is handled within the nvm_lun
lock.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

The get/set bad block interface defines good block, factory bad block,
grown bad block, device reserved block, and host reserved block.
Unfortunately the grown bad block was missing, leaving the offsets wrong
for device and host side reserved blocks.

This patch adds the missing type and corrects the offsets.
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Currently, a rrpc block only points to its nvm_lun. If a user wants to
find the associated rrpc lun, it will have to calculate the index and
look it up manually. By referencing the rrpc lun directly, this step can
be omitted, at the cost of a larger memory footprint.

This is important for upcoming patches that implement write buffering in
rrpc.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Internal logic for both core and media managers, does not have a
backing bio for issuing I/Os. Introduce nvm_submit_ppa to allow raw
I/Os to be submitted to the underlying device driver.

The function request the device, ppa, data buffer and its length and
will submit the I/O synchronously to the device. The return value may
therefore be used to detect any errors regarding the issued I/O.
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Instead of passing request error into the LightNVM modules, incorporate
it into the nvm_rq.
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Sometimes a user want to erase multiple PPAs at the same time. Extend
nvm_erase_ppa to take multiple ppas and number of ppas to be erased.
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

There is no need to check whether dev's pages per block is
beyond rrpc support every time we init a lun, we only need
to check it once before enter the lun init loop.
Signed-off-by: NWenwei Tao <ww.tao0320@gmail.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

The Westlake controller requires that the PPA list has sectors defined
sequentially. Currently, the PPA list is created with planes first, then
sectors. Change this to sectors first, then planes.
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

This patch fix two issues in rrpc_lun_gc

1. prio_list is protected by rrpc_lun's lock not nvm_lun's, so
acquire rlun's lock instead of lun's before operate on the list.

2. we delete block from prio_list before allocating gcb, but gcb
allocation may fail, we end without putting it back to the list,
this makes the block won't get reclaimed in the future. To solve
this issue, delete block after gcb allocation.
Signed-off-by: NWenwei Tao <ww.tao0320@gmail.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

We delete a block from the gc list before reclaim it, so
put it back to the list on its reclaim fail, otherwise
this block will not get reclaimed and be programmable
in the future.
Signed-off-by: NWenwei Tao <ww.tao0320@gmail.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

We should check last io completion status before
starting another one.
Signed-off-by: NWenwei Tao <ww.tao0320@gmail.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

During get_bb_tbl, a callback is used to allow an user-specific scan
function to be called. The callback may return an error, and in that
case, the return value is overridden. However, the callback error is
needed when the fault is a user error and not a kernel error. For
example, when a user tries to initialize the same device twice. The
get_bb_tbl callback should be able to communicate this.
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

To implement sync I/O support within the LightNVM core, the end_io
functions are refactored to take an end_io function pointer instead of
testing for initialized media manager, followed by calling its end_io
function.

Sync I/O can then be implemented using a callback that signal I/O
completion. This is similar to the logic found in blk_to_execute_io().
By implementing it this way, the underlying device I/Os submission logic
is abstracted away from core, targets, and media managers.
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

A device may be driven in single, double or quad plane mode. In that
case, the rqd must have either one, two, or four PPAs set for a single
PPA sent to the device. Refactor this logic into their own
functions to be shared by program/erase/read in the core.
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

A device may function in single, dual or quad plane mode. The gennvm
media manager manages this with explicit helpers. They convert a single
ppa to 1, 2 or 4 separate ppas in a ppa list. To aid implementation of
recovery and system blocks, this functionality can be moved directly
into the core.
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

When rrpc_write_ppalist_rq and rrpc_read_ppalist_rq succeed, we setup
rq correctly, but nvm_submit_io may afterward fail since it cannot
allocate request or nvme_nvm_command, we return error but forget to
cleanup the previous work.
Signed-off-by: NWenwei Tao <ww.tao0320@gmail.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

The mempool allocation might fail. Make sure to return error when it
does, instead of causing a kernel panic.
Signed-off-by: NJavier Gonzalez <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

When initing bad block list in gennvm_block_bb, once we move bad block
from free_list to bb_list, we should maintain both stat info
nr_free_blocks and nr_bad_blocks. So this patch fixes to add missing
operation related to nr_free_blocks.
Signed-off-by: NChao Yu <chao2.yu@samsung.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Put bio when submission fails, since we get it
before submission. And return error when backend
device driver doesn't provide a submit_io method,
thus we can end IO properly.
Signed-off-by: NWenwei Tao <ww.tao0320@gmail.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Pull MIPS build fix from Ralf Baechle:
 "Fix a makefile issue resulting in build breakage with older binutils.

  This has sat in -next for a few days, testers and buildbot are happy
  with it, too though if you are going for another -rc that'd certainly
  help ironing out a few more issues"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: VDSO: Fix build error with binutils 2.24 and earlier

Pull i915 drm fixes from Jani Nikula:
 "Two display fixes still for v4.4.

  The new year's resolution is to start using signed tags per Linus'
  request.  This one is still unsigned; I want to fix this up in our
  maintainer scripts instead of doing it one-off"

* tag 'drm-intel-fixes-2016-01-02' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: increase the tries for HDMI hotplug live status checking
  drm/i915: Unbreak check_digital_port_conflicts()

Pull PCI bugfix from Bjorn Helgaas:
 "Here's another fix for v4.4.

  This fixes 32-bit config reads for the HiSilicon driver.  Obviously
  the driver is completely broken without this fix (apparently it
  actually was tested internally, but got broken somehow in the process
  of upstreaming it).

  Summary:

  HiSilicon host bridge driver
    Fix 32-bit config reads (Dongdong Liu)"

* tag 'pci-v4.4-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: hisi: Fix hisi_pcie_cfg_read() 32-bit reads

Pull sparc fixes from David Miller:
 "Just some missing syscall wire ups"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: Wire up mlock2 system call.
  sparc: Add all necessary direct socket system calls.

Pull networking fixes from David Miller:

 1) Prevent XFRM per-cpu counter updates for one namespace from being
    applied to another namespace.  Fix from DanS treetman.

 2) Fix RCU de-reference in iwl_mvm_get_key_sta_id(), from Johannes
    Berg.

 3) Remove ethernet header assumption in nft_do_chain_netdev(), from
    Pablo Neira Ayuso.

 4) Fix cpsw PHY ident with multiple slaves and fixed-phy, from Pascal
    Speck.

 5) Fix use after free in sixpack_close and mkiss_close.

 6) Fix VXLAN fw assertion on bnx2x, from Yuval Mintz.

 7) natsemi doesn't check for DMA mapping errors, from Alexey
    Khoroshilov.

 8) Fix inverted test in ip6addrlbl_get(), from ANdrey Ryabinin.

 9) Missing initialization of needed_headroom in geneve tunnel driver,
    from Paolo Abeni.

10) Fix conntrack template leak in openvswitch, from Joe Stringer.

11) Mission initialization of wq->flags in sock_alloc_inode(), from
    Nicolai Stange.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
  sctp: sctp should release assoc when sctp_make_abort_user return NULL in sctp_close
  net, socket, socket_wq: fix missing initialization of flags
  drivers: net: cpsw: fix error return code
  openvswitch: Fix template leak in error cases.
  sctp: label accepted/peeled off sockets
  sctp: use GFP_USER for user-controlled kmalloc
  qlcnic: fix a loop exit condition better
  net: cdc_ncm: avoid changing RX/TX buffers on MTU changes
  geneve: initialize needed_headroom
  ipv6: honor ifindex in case we receive ll addresses in router advertisements
  addrconf: always initialize sysctl table data
  ipv6/addrlabel: fix ip6addrlbl_get()
  switchdev: bridge: Pass ageing time as clock_t instead of jiffies
  sh_eth: fix 16-bit descriptor field access endianness too
  veth: don’t modify ip_summed; doing so treats packets with bad checksums as good.
  net: usb: cdc_ncm: Adding Dell DW5813 LTE AT&T Mobile Broadband Card
  net: usb: cdc_ncm: Adding Dell DW5812 LTE Verizon Mobile Broadband Card
  natsemi: add checks for dma mapping errors
  rhashtable: Kill harmless RCU warning in rhashtable_walk_init
  openvswitch: correct encoding of set tunnel action attributes
  ...

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The GLIBC folks would like to eliminate socketcall support
eventually, and this makes sense regardless so wire them
all up.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In sctp_close, sctp_make_abort_user may return NULL because of memory
allocation failure. If this happens, it will bypass any state change
and never free the assoc. The assoc has no chance to be freed and it
will be kept in memory with the state it had even after the socket is
closed by sctp_close().

So if sctp_make_abort_user fails to allocate memory, we should abort
the asoc via sctp_primitive_ABORT as well. Just like the annotation in
sctp_sf_cookie_wait_prm_abort and sctp_sf_do_9_1_prm_abort said,
"Even if we can't send the ABORT due to low memory delete the TCB.
This is a departure from our typical NOMEM handling".

But then the chunk is NULL (low memory) and the SCTP_CMD_REPLY cmd would
dereference the chunk pointer, and system crash. So we should add
SCTP_CMD_REPLY cmd only when the chunk is not NULL, just like other
places where it adds SCTP_CMD_REPLY cmd.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2015-12-28' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
iwlwifi

* don't load firmware that won't exist for 7260
* fix RCU splat
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit ceb5d58b ("net: fix sock_wake_async() rcu protection") from
the current 4.4 release cycle introduced a new flags member in
struct socket_wq and moved SOCKWQ_ASYNC_NOSPACE and SOCKWQ_ASYNC_WAITDATA
from struct socket's flags member into that new place.

Unfortunately, the new flags field is never initialized properly, at least
not for the struct socket_wq instance created in sock_alloc_inode().

One particular issue I encountered because of this is that my GNU Emacs
failed to draw anything on my desktop -- i.e. what I got is a transparent
window, including the title bar. Bisection lead to the commit mentioned
above and further investigation by means of strace told me that Emacs
is indeed speaking to my Xorg through an O_ASYNC AF_UNIX socket. This is
reproducible 100% of times and the fact that properly initializing the
struct socket_wq ->flags fixes the issue leads me to the conclusion that
somehow SOCKWQ_ASYNC_WAITDATA got set in the uninitialized ->flags,
preventing my Emacs from receiving any SIGIO's due to data becoming
available and it got stuck.

Make sock_alloc_inode() set the newly created struct socket_wq's ->flags
member to zero.

Fixes: ceb5d58b ("net: fix sock_wake_async() rcu protection")
Signed-off-by: NNicolai Stange <nicstange@gmail.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull block fixes from Jens Axboe:
 "Make the block layer great again.

  Basically three amazing fixes in this pull request, split into 4
  patches.  Believe me, they should go into 4.4.  Two of them fix a
  regression, the third and last fixes an easy-to-trigger bug.

   - Fix a bad irq enable through null_blk, for queue_mode=1 and using
     timer completions.  Add a block helper to restart a queue
     asynchronously, and use that from null_blk.  From me.

   - Fix a performance issue in NVMe.  Some devices (Intel Pxxxx) expose
     a stripe boundary, and performance suffers if we cross it.  We took
     that into account for merging, but not for the newer splitting
     code.  Fix from Keith.

   - Fix a kernel oops in lightnvm with multiple channels.  From Matias"

* 'for-linus' of git://git.kernel.dk/linux-block:
  lightnvm: wrong offset in bad blk lun calculation
  null_blk: use async queue restart helper
  block: add blk_start_queue_async()
  block: Split bios on chunk boundaries

The total delay of HDMI hotplug detecting with 30ms is sometimes not
enoughtfor HDMI live status up with specific HDMI monitors in BSW platform.

After doing experiments for following monitors, it needs 80ms at least
for those worst cases.

Lenovo L246 1xwA (4 failed, necessary hot-plug delay: 58/40/60/40ms)
Philips HH2AP (9 failed, necessary hot-plug delay: 80/50/50/60/46/40/58/58/39ms)
BENQ ET-0035-N (6 failed, necessary hot-plug delay: 60/50/50/80/80/40ms)
DELL U2713HM (2 failed, necessary hot-plug delay: 58/59ms)
HP HP-LP2475w (5 failed, necessary hot-plug delay: 70/50/40/60/40ms)

It looks like 70-80 ms is BSW platform needs in some bad cases of the
monitors at this end (8 times delay at most). Keep less than 100ms for
HDCP pulse HPD low (with at least 100ms) to respond a plug out.
Reviewed-by: NCooper Chiou <cooper.chiou@intel.com>
Tested-by: NGary Wang <gary.c.wang@intel.com>
Cc: Gavin Hindman <gavin.hindman@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: NGary Wang <gary.c.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450858295-12804-1-git-send-email-gary.c.wang@intel.comTested-by: NShobhit Kumar <shobhit.kumar@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: 237ed86c ("drm/i915: Check live status before reading edid")
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit f8d03ea0)
[Jani: undo the file mode change of the original commit]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Merge misc fixes from Andrew Morton:
 "9 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm/vmstat: fix overflow in mod_zone_page_state()
  ocfs2/dlm: clear migration_pending when migration target goes down
  mm/memory_hotplug.c: check for missing sections in test_pages_in_a_zone()
  ocfs2: fix flock panic issue
  m32r: add io*_rep helpers
  m32r: fix build failure
  arch/x86/xen/suspend.c: include xen/xen.h
  mm: memcontrol: fix possible memcg leak due to interrupted reclaim
  ocfs2: fix BUG when calculate new backup super

Pull vfs fix from Al Viro:
 "Fix for 3.15 breakage of fcntl64() in arm OABI compat.  -stable
  fodder"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  [PATCH] arm: fix handling of F_OFD_... in oabi_fcntl64()

mod_zone_page_state() takes a "delta" integer argument.  delta contains
the number of pages that should be added or subtracted from a struct
zone's vm_stat field.

If a zone is larger than 8TB this will cause overflows.  E.g.  for a
zone with a size slightly larger than 8TB the line

    mod_zone_page_state(zone, NR_ALLOC_BATCH, zone->managed_pages);

in mm/page_alloc.c:free_area_init_core() will result in a negative
result for the NR_ALLOC_BATCH entry within the zone's vm_stat, since 8TB
contain 0x8xxxxxxx pages which will be sign extended to a negative
value.

Fix this by changing the delta argument to long type.

This could fix an early boot problem seen on s390, where we have a 9TB
system with only one node.  ZONE_DMA contains 2GB and ZONE_NORMAL the
rest.  The system is trying to allocate a GFP_DMA page but ZONE_DMA is
completely empty, so it tries to reclaim pages in an endless loop.

This was seen on a heavily patched 3.10 kernel.  One possible
explaination seem to be the overflows caused by mod_zone_page_state().
Unfortunately I did not have the chance to verify that this patch
actually fixes the problem, since I don't have access to the system
right now.  However the overflow problem does exist anyway.

Given the description that a system with slightly less than 8TB does
work, this seems to be a candidate for the observed problem.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We have found a BUG on res->migration_pending when migrating lock
resources.  The situation is as follows.

dlm_mark_lockres_migration
  res->migration_pending = 1;
  __dlm_lockres_reserve_ast
  dlm_lockres_release_ast returns with res->migration_pending remains
      because other threads reserve asts
  wait dlm_migration_can_proceed returns 1
  >>>>>>> o2hb found that target goes down and remove target
          from domain_map
  dlm_migration_can_proceed returns 1
  dlm_mark_lockres_migrating returns -ESHOTDOWN with
      res->migration_pending still remains.

When reentering dlm_mark_lockres_migrating(), it will trigger the BUG_ON
with res->migration_pending.  So clear migration_pending when target is
down.
Signed-off-by: NJiufei Xue <xuejiufei@huawei.com>
Reviewed-by: NJoseph Qi <joseph.qi@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

test_pages_in_a_zone() does not account for the possibility of missing
sections in the given pfn range.  pfn_valid_within always returns 1 when
CONFIG_HOLES_IN_ZONE is not set, allowing invalid pfns from missing
sections to pass the test, leading to a kernel oops.

Wrap an additional pfn loop with PAGES_PER_SECTION granularity to check
for missing sections before proceeding into the zone-check code.

This also prevents a crash from offlining memory devices with missing
sections.  Despite this, it may be a good idea to keep the related patch
'[PATCH 3/3] drivers: memory: prohibit offlining of memory blocks with
missing sections' because missing sections in a memory block may lead to
other problems not covered by the scope of this fix.
Signed-off-by: NAndrew Banman <abanman@sgi.com>
Acked-by: NAlex Thorlton <athorlton@sgi.com>
Cc: Russ Anderson <rja@sgi.com>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Seth Jennings <sjennings@variantweb.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>