Currently support only default geneve udp port (6081).
For the tx side, the HW is assisted by SW parsing, which sets the
headers offset to offload tunneled LSO and csum. Note that for udp
tunnels, we don't use special rx offloads, as rss on the outer headers
is enough, we support checksum complete and GRO takes care of
aggregation.

Geneve TSO BW and CPU load results (tested using iperf single tcp
stream).
In this patch we add TSO support over Geneve, so the "before" result
doesn't actually get to using the TSO HW offload even when turned on.
Tested on ConnectX-5, Intel(R) Xeon(R) CPU E5-2660 v2 @2.20GHz.

 __________________________________
| Before         | After           |
|________________|_________________|
| 12.6 Gbits/sec | 21.7 Gbits/sec  |
| 100% CPU load  | 61.5% CPU load  |
|________________|_________________|
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Acked-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Refactor mlx5e_ipsec_set_swp() code, split the part which sets the eseg
software parser (SWP) offsets and flags, so it can be used in a
downstream patch by other mlx5e functionality which needs to set eseg
SWP.
The new function mlx5e_set_eseg_swp() is useful for setting swp for both
outer and inner headers. It also handles the special ipsec case of xfrm
mode transfer.
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Move the definition of the default Geneve udp port from the geneve
source to the header file, so we can re-use it from drivers.
Modify existing drivers to use it.
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Cc: John Hurley <john.hurley@netronome.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Remove redundant assignment to tun_entropy->enabled.

Addesses-Coverity-ID: 1477328 ("Unused value")
Fixes: 97417f61 ("net/mlx5e: Fix GRE key by controlling port tunnel entropy calculation")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NEli Britstein <elibr@mellanox.com>
Acked-by: NLeon Romanovsky <leonro@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Amazingly a mlx5e_tc function is being called from the eswitch layer,
which is by itself very terrible! The function was declared locally in
eswitch_offloads.c so it could be used there, which caused the following
compilation warning, fix that.

drivers/.../mlx5/core/en_tc.c:3242:6: [-Werror=missing-prototypes]
error: no previous prototype for ‘mlx5e_tc_clean_fdb_peer_flows’

Fixes: 04de7dda ("net/mlx5e: Infrastructure for duplicated offloading of TC flows")
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

This patch fixes compiler warnings:
In drivers/.../mlx5/core/en/port_buffer.c:190:
warning: Function parameter or member 'pfc_en' not described...
...
warning: Function parameter or member 'change' not described...

Fixes: 0696d608 ("net/mlx5e: Receive buffer configuration")
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

mlx5_eq_table_get_rmap is being used only when CONFIG_RFS_ACCEL is
enabled, this patch fixes the below warning when CONFIG_RFS_ACCEL is
disabled.

drivers/.../mlx5/core/eq.c:903:18: [-Werror=missing-prototypes]
error: no previous prototype for ‘mlx5_eq_table_get_rmap’

Fixes: f2f3df55 ("net/mlx5: EQ, Privatize eq_table and friends")
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

It is desired to get rid of num_vfs stored inside mlx5_core_sriov to
safely support vports more than vfs.
To reduce dependency on mlx5_core_sriov num_vfs, start using
pci_num_vf() from pci core.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NBodong Wang <bodong@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Macro MLX5_TOTAL_VPORTS() returns total number of vports. Therefore,
rename variable total_vfs to total_vports to improve code readability.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NBodong Wang <bodong@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Simplify sriov enable/disable flow for below two checks.

1. PCI core driver allows sriov configuration only on a PF.
This is done in drivers/pci/pci-sysfs.c sriov_attrs_are_visible().

2. PCI core driver allow sriov enablement if the sriov is currently
disabled for for a PF. This is done in drivers/pci/pci-sysfs.c
sriov_numvfs_store().

Hence there is no need for mlx5 driver to duplicate such checks.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NBodong Wang <bodong@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Since maxattr is common, the policy can't really differ sanely,
so make it common as well.

The only user that did in fact manage to make a non-common policy
is taskstats, which has to be really careful about it (since it's
still using a common maxattr!). This is no longer supported, but
we can fake it using pre_doit.

This reduces the size of e.g. nl80211.o (which has lots of commands):

   text	   data	    bss	    dec	    hex	filename
 398745	  14323	   2240	 415308	  6564c	net/wireless/nl80211.o (before)
 397913	  14331	   2240	 414484	  65314	net/wireless/nl80211.o (after)
--------------------------------
   -832      +8       0    -824

Which is obviously just 8 bytes for each command, and an added 8
bytes for the new policy pointer. I'm not sure why the ops list is
counted as .text though.

Most of the code transformations were done using the following spatch:
    @ops@
    identifier OPS;
    expression POLICY;
    @@
    struct genl_ops OPS[] = {
    ...,
     {
    -	.policy = POLICY,
     },
    ...
    };

    @@
    identifier ops.OPS;
    expression ops.POLICY;
    identifier fam;
    expression M;
    @@
    struct genl_family fam = {
            .ops = OPS,
            .maxattr = M,
    +       .policy = POLICY,
            ...
    };

This also gets rid of devlink_nl_cmd_region_read_dumpit() accessing
the cb->data as ops, which we want to change in a later genl patch.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the call to netif_wake_queue in rtl8169_start_xmit with
netif_start_queue as we don't need to actually wake up the queue since
we are still in mid transmit so we just need to reset the bit so it
doesn't prevent the next transmit.
(Description shamelessly copied from a mail sent by Alex.)
Suggested-by: NAlexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Aquantia PHY's of the AQR107 family support the downshift feature.
Add support for it as standard PHY tunable so that it can be controlled
via ethtool.
The AQCS109 supports a proprietary 2-pair 1Gbps mode. If two such PHY's
are connected to each other with a 2-pair cable, they may not be able
to establish a link if both advertise modes > 1Gbps.

v2:
- add downshift event detection
- warn if downshift occurred
- read downshifted rate from vendor register
- enable downshift per default on all AQR107 family members
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NFP driver ABI contains bits for L2 switching which were never
implemented in initially envisioned form.

Remove the defines, and open up the possibility of
reclaiming the bits for other uses.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cygnus and Omega are part of the same business unit and product line, it
makes sense to group PHY entries by products such that a platform can
select only the drivers that it needs. Bring all the functionality that
the BCM7XXX_28NM_GPHY() macro hides for us and remove the Omega PHY
entry from bcm7xxx.c.

As an added bonus, we now have a proper mdio_device_id entry to permit
auto-loading.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NScott Branden <scott.branden@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Omega PHY entry was added to bcm7xxx.c out of convenience and this
breaks the one driver per product line paradigm that was applied up
until now. Since the AFE initialization is shared between Omega and
BCM7xxx move the relevant functions to bcm-phy-lib.[ch]. No functional
changes introduced.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NScott Branden <scott.branden@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit ad67b74d ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful, especially given we use a dev_info() which
already displays the platform device's address.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit ad67b74d ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful, we use a dev_info() print which already
displays the platform device's address.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit ad67b74d ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful, especially given we use a dev_info() which
already displays the platform device's address.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NKirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit f2780d6d "tun: Add ioctl() SIOCGSKNS cmd to allow
obtaining net ns of tun device" it was missed that tun may change
its net ns, while net ns of socket remains the same as it was
created initially. SIOCGSKNS returns net ns of socket, so it is
not suitable for obtaining net ns of device.

We may have two tun devices with the same names in two net ns,
and in this case it's not possible to determ, which of them
fd refers to (TUNGETIFF will return the same name).

This patch adds new ioctl() cmd for obtaining net ns of a device.
Reported-by: NHarald Albrecht <harald.albrecht@gmx.net>
Signed-off-by: NKirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix sparse warning:

drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.c:414:6:
 warning: symbol 'hclge_destroy_cmd_queue' was not declared. Should it be static?
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the previous patch, all the callers of ndo_select_queue()
provide as a 'fallback' argument netdev_pick_tx.
The only exceptions are nested calls to ndo_select_queue(),
which pass down the 'fallback' available in the current scope
- still netdev_pick_tx.

We can drop such argument and replace fallback() invocation with
netdev_pick_tx(). This avoids an indirect call per xmit packet
in some scenarios (TCP syn, UDP unconnected, XDP generic, pktgen)
with device drivers implementing such ndo. It also clean the code
a bit.

Tested with ixgbe and CONFIG_FCOE=m

With pktgen using queue xmit:
threads		vanilla 	patched
		(kpps)		(kpps)
1		2334		2428
2		4166		4278
4		7895		8100

 v1 -> v2:
 - rebased after helper's name change
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch introduces a new Multi-Function bit for cases where firmware
shouldn't perform the insertion of vlan-0 tag. The new bit is defined to
abstract the implementation from the actual MF mode.
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds support to display MBI image version in 'ethtool -i' output.
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similiar to commit a6111d3c ("vlan: Pass SIOC[SG]HWTSTAMP ioctls to
real device") and commit 37dd9255 ("vlan: Pass ethtool get_ts_info
queries to real device."), add MACVlan HW ptp support.
Signed-off-by: NHangbin Liu <liuhangbin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Depending on the auto-negotiated speed the PHY may change the interface
mode. Check for new mode and set phydev->interface accordingly.
Signed-off-by: NNikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: picked from bigger patch and reworked]
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let config_init check for unsupported interface modes on AQR107/AQCS109.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: adjusted for AQR107/AQCS109 specifics]
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the Phy driver's link_change_notify callback is called
whenever the state machine is run (every second if polling), no matter
whether the state changed or not. This isn't needed and may confuse
users considering the name of the callback. Actually it contradicts
its kernel-doc description. Therefore let's change the behavior and
call this callback only in case of an actual state change.

This requires changes to the at803x and rockchip drivers.
at803x can be simplified so that it reacts on a state change to
PHY_NOLINK only.
The rockchip driver can also be much simplified. We simply re-init
the AFE/DSP registers whenever we change to PHY_RUNNING and speed
is 100Mbps. This causes very small overhead because we do this even
if the speed was 100Mbps already. But this is negligible and
I think justified by the much simpler code.

Changes are compile-tested only.

A little bit problematic seems to be to find somebody with the
hardware to test the changes to the two PHY drivers. See also [0].
David may be able to test the Rockchip driver.

[0] https://marc.info/?t=153782508800006&r=1&w=2Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we set the default number of Tx and Rx descriptors to 128 by
default. For Rx this amounts to a full page (assuming 4K pages) because
each Rx descriptor is 32 Bytes, but for Tx it only amounts to a half
page because each Tx descriptor is 16 Bytes (assuming 4K pages).
Instead of assuming 4K pages, determine the ring size and the number of
descriptors for Tx and Rx based on a calculation using the PAGE_SIZE,
ICE_MAX_NUM_DESC, and ICE_REQ_DESC_MULTIPLE. This change is being made
to improve the performance of the driver when using the default
settings.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During SR-IOV initialization, we allocate and setup VFs with reset, and
since we were going to inform Firmware about our intention to do VFLR by
disabling LAN TX Queue, then we really have to complete VF reset flow with
VFLR using appropriate registers - Otherwise, reset status bit for VF in
the Guest OS might returns DEADBEEF.
This resolves issue to properly initialize VFs in the Guest OS via PCI
passthrough.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ice_get_guar_num_vsi currently calculates the number of VSIs per PF.
Rework this into a general function ice_get_num_per_func, that can
calculate per PF allocations for not just VSIs but across multiple
resource types.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

All VF VSIs need to be reset and rebuild with the main VSIs before
replaying all VSIs, so that all existing switch filters, scheduler tree
and other configuration could be replayed at once. This fixes issues when
doing PFR and CORER reset.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of hoping that our ITR granularity will be 2 usec program the
GLINT_CTL register to make sure the ITR granularity is always 2 usecs.

Now that we know what the ITR granularity will be get rid of the check
in ice_probe() to verify our previous assumption.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Replace all instances of:
	for (i = 0; i < pf->num_alloc_vsi; i++)

with the following macro:
	ice_for_each_vsi(pf, i)

This will allow the code to be consistent since there are currently
cases of using both.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In the ice_aq_set_phy_cfg AQ command, the 16.4 bit is reserved. This
patch will make sure that this bit will never be set to 1.
Signed-off-by: NChinh T Cao <chinh.t.cao@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In ice_pf_rxq_wait we are using an unnecessary local variable and also
we are checking if the timeout time was reached after the loop. Get rid
of the local variable and return 0 right when we get a successful
result. This makes it so we can return -ETIMEDOUT if we ever exit the
loop because we know the timeout time has been hit.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a local variable struct device *dev to avoid unnecessary de-references
throughout ice_probe().
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes issues with VF queues being disabled, and VF netdev
network carrier being lost after reset. Basically, we need to check if VF
is enabled, and queue configured in reset_all_vfs flow, and disable/enable
those queues appropriately whenever the function is called after
Global/CORER/PFR reset/rebuild/replay.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Set egress (Rx) pruning enable flag for VF VSI in VSI ctxt to
enable prune action.

To avoid seeing broadcast packet in different VLAN, pruning enable
flag in VSI ctxt should be set.

Write new functions (fill VSI ctx) to not repeat send ctxt code.
Signed-off-by: NMichal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>