- 16 10月, 2018 9 次提交
-
-
由 Michael Chan 提交于
57500 series is a new chip class (P5) that requires some driver changes in the next several patches. This adds basic chip ID, doorbells, and the notification queue (NQ) structures. Each MSIX is associated with an NQ instead of a CP ring in legacy chips. Each NQ has up to 2 associated CP rings for RX and TX. The same bnxt_cp_ring_info struct will be used for the NQ. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Call firmware to configure the DMA addresses of all context memory pages on new devices requiring context memory. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
New device requires host context memory as a backing store. Call firmware to check for context memory requirements and store the parameters. Allocate host pages accordingly. We also need to move the call bnxt_hwrm_queue_qportcfg() earlier so that all the supported hardware queues and the IDs are known before checking and allocating context memory. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Newer chips require the PTU_PTE_VALID bit to be set for every page table entry for context memory and rings. Additional bits are also required for page table entries for all rings. Add a flags field to bnxt_ring_mem_info struct to specify these additional bits to be used when setting up the pages tables as needed. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Move the DMA page table and vmem fields in bnxt_ring_struct to a new bnxt_ring_mem_info struct. This will allow context memory management for a new device to re-use some of the existing infrastructure. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
New firmware spec. allows interrupt coalescing parameters, such as maximums, timer units, supported features to be queried. Update the driver to make use of the new call to query these parameters and provide the legacy defaults if the call is not available. Replace the hard-coded values with these parameters. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Support the max_ext_req_len field from the HWRM_VER_GET_RESPONSE. If this field is valid and greater than the mailbox size, use the short command format to send firmware messages greater than the mailbox size. Newer devices use this method to send larger messages to the firmware. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Latest firmware spec. has some additional rx extended port stats and new tx extended port stats added. We now need to check the size of the returned rx and tx extended stats and determine how many counters are valid. New counters added include CoS byte and packet counts for rx and tx. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Among the new changes are trusted VF support, 200Gbps support, and new API to dump ring information on the new chips. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 08 10月, 2018 1 次提交
-
-
由 Gustavo A. R. Silva 提交于
There is no need to compare *val.vu32* with < 0 because such variable is of type u32 (32 bits, unsigned), making it impossible to hold a negative value. Fix this by removing such comparison. Also, initialize variable *max_val* to -1, just in case it is not initialized to either BNXT_MSIX_VEC_MAX or BNXT_MSIX_VEC_MIN_MAX before using it in a comparison with val.vu32 at line 159: if (val.vu32 > max_val) Addresses-Coverity-ID: 1473915 ("Unsigned compared against 0") Addresses-Coverity-ID: 1473920 ("Uninitialized scalar variable") Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 10月, 2018 8 次提交
-
-
由 Vasundhara Volam 提交于
When getting the max rings supported, get the reduced max_irqs by the ones used by RDMA. If the number MSIX is the limiting factor, this bug may cause the max ring count to be higher than it should be when RDMA driver is loaded and may result in ring allocation failures. Fixes: 30f52947 ("bnxt_en: Do not modify max IRQ count after RDMA driver requests/frees IRQs.") Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Venkat Duvvuru 提交于
When the driver probe fails, all the resources that were allocated prior to the failure must be freed. However, hwrm dma response memory is not getting freed. This patch fixes the problem described above. Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: NVenkat Duvvuru <venkatkumar.duvvuru@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vasundhara Volam 提交于
In HWRM_QUEUE_COS2BW_CFG request, enables field should have the bits set only for the queue ids which are having the valid parameters. This causes firmware to return error when the TC to hardware CoS queue mapping is not 1:1 during DCBNL ETS setup. Fixes: 2e8ef77e ("bnxt_en: Add TC to hardware QoS queue mapping logic.") Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The enables bit for VNIC was set wrong when calling the HWRM_FUNC_CFG firmware call to reserve VNICs. This has the effect that the firmware will keep a large number of VNICs for the PF, and having very few for VFs. DPDK driver running on the VFs, which requires more VNICs, may not work properly as a result. Fixes: 674f50a5 ("bnxt_en: Implement new method to reserve rings.") Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vasundhara Volam 提交于
This patch adds following driver-specific permanent mode boolean parameter. gre_ver_check - Generic Routing Encapsulation(GRE) version check will be enabled in the device. If disabled, device skips version checking for GRE packets. Cc: Michael Chan <michael.chan@broadcom.com> Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vasundhara Volam 提交于
This patch adds support for following generic permanent mode devlink parameters. They can be modified using devlink param commands. msix_vec_per_pf_max - This param sets the number of MSIX vectors that the device requests from the host on driver initialization. This value is set in the device which limits MSIX vectors per PF. msix_vec_per_pf_min - This param sets the number of minimal MSIX vectors required for the device initialization. Value 0 indicates a default value is selected. This value is set in the device which limits MSIX vectors per PF. Cc: Michael Chan <michael.chan@broadcom.com> Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vasundhara Volam 提交于
Return proper error code when Firmware returns HWRM_ERR_CODE_RESOURCE_ACCESS_DENIED for HWRM_NVM_GET/SET_VARIABLE commands. Cc: Michael Chan <michael.chan@broadcom.com> Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vasundhara Volam 提交于
This patch adds support for ignore_ari generic permanent mode devlink parameter. This parameter is disabled by default. It can be enabled using devlink param commands. ignore_ari - If enabled, device ignores ARI(Alternate Routing ID) capability, even when platforms has the support and creates same number of partitions when platform does not support ARI capability. Cc: Michael Chan <michael.chan@broadcom.com> Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 10月, 2018 1 次提交
-
-
由 Eli Britstein 提交于
Add extack argument to the eswitch related operations. Signed-off-by: NEli Britstein <elibr@mellanox.com> Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com> Reviewed-by: NRoi Dayan <roid@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
-
- 03 10月, 2018 1 次提交
-
-
由 Florian Fainelli 提交于
The AON_PM_L2 is normally used to trigger and identify the source of a wake-up event. Since the RX_SYS clock is no longer turned off, we also have an interrupt being sent to the SYSTEMPORT INTRL_2_0 controller, and that interrupt remains active up until the magic packet detector is disabled which happens much later during the driver resumption. The race happens if we have a CPU that is entering the SYSTEMPORT INTRL2_0 handler during resume, and another CPU has managed to clear the wake-up interrupt during bcm_sysport_resume_from_wol(). In that case, we have the first CPU stuck in the interrupt handler with an interrupt cause that has been cleared under its feet, and so we keep returning IRQ_NONE and we never make any progress. This was not a problem before because we would always turn off the RX_SYS clock during WoL, so the SYSTEMPORT INTRL2_0 would also be turned off as well, thus not latching the interrupt. The fix is to make sure we do not enable either the MPD or BRCM_TAG_MATCH interrupts since those are redundant with what the AON_PM_L2 interrupt controller already processes and they would cause such a race to occur. Fixes: bb9051a2 ("net: systemport: Add support for WAKE_FILTER") Fixes: 83e82f4c ("net: systemport: add Wake-on-LAN support") Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 02 10月, 2018 5 次提交
-
-
由 Florian Fainelli 提交于
When inserting the TSB, keep track of how many times we had to do it and if there was a failure in doing so, this helps profile the driver for possibly incorrect headroom settings. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
During bcm_sysport_insert_tsb() make sure we differentiate a SKB headroom re-allocation failure from the normal swap and replace path. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
We can turn on the RX/TX checksum offloads by default and make sure that those are properly reflected back to e.g: stacked devices such as VLAN or DSA. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
During driver resume and open, the HW may have lost its context/state, utilize bcm_sysport_set_features() to make sure we do restore the correct set of features that were previously configured. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
In preparation for unconditionally enabling TX and RX checksum offloads, refactor bcm_sysport_set_features() a bit such that __netdev_update_features() during register_netdev() can make sure that features are correctly programmed during network device registration. Since we can now be called during register_netdev() with clocks gated, we need to temporarily turn them on/off in order to have a successful register programming. We also move the CRC forward setting read into bcm_sysport_set_features() since priv->crc_fwd matters while turning on RX checksum offload, that way we are guaranteed they are in sync in case we ever add support for NETIF_F_RXFCS at some point in the future. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 9月, 2018 1 次提交
-
-
由 Michael Chan 提交于
The current netpoll implementation in the bnxt_en driver has problems that may miss TX completion events. bnxt_poll_work() in effect is only handling at most 1 TX packet before exiting. In addition, there may be in flight TX completions that ->poll() may miss even after we fix bnxt_poll_work() to handle all visible TX completions. netpoll may not call ->poll() again and HW may not generate IRQ because the driver does not ARM the IRQ when the budget (0 for netpoll) is reached. We fix it by handling all TX completions and to always ARM the IRQ when we exit ->poll() with 0 budget. Also, the logic to ACK the completion ring in case it is almost filled with TX completions need to be adjusted to take care of the 0 budget case, as discussed with Eric Dumazet <edumazet@google.com> Reported-by: NSong Liu <songliubraving@fb.com> Reviewed-by: NSong Liu <songliubraving@fb.com> Tested-by: NSong Liu <songliubraving@fb.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 9月, 2018 2 次提交
-
-
由 Eric Dumazet 提交于
As diagnosed by Song Liu, ndo_poll_controller() can be very dangerous on loaded hosts, since the cpu calling ndo_poll_controller() might steal all NAPI contexts (for all RX/TX queues of the NIC). This capture can last for unlimited amount of time, since one cpu is generally not able to drain all the queues under load. bnxt uses NAPI for TX completions, so we better let core networking stack call the napi->poll() to avoid the capture. Signed-off-by: NEric Dumazet <edumazet@google.com> Cc: Michael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
As diagnosed by Song Liu, ndo_poll_controller() can be very dangerous on loaded hosts, since the cpu calling ndo_poll_controller() might steal all NAPI contexts (for all RX/TX queues of the NIC). This capture can last for unlimited amount of time, since one cpu is generally not able to drain all the queues under load. bnx2x uses NAPI for TX completions, so we better let core networking stack call the napi->poll() to avoid the capture. Signed-off-by: NEric Dumazet <edumazet@google.com> Cc: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 22 9月, 2018 3 次提交
-
-
由 Shahed Shaikh 提交于
Provide current link status of VF in ndo_get_vf_config handler. Signed-off-by: NShahed Shaikh <Shahed.Shaikh@cavium.com> Signed-off-by: NAriel Elior <ariel.elior@cavium.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shahed Shaikh 提交于
This is a workaround for FW bug - MFW generates bandwidth attention in single function mode, which is only expected to be generated in multi function mode. This undesired attention in SF mode results in incorrect HW configuration and resulting into Tx timeout. Signed-off-by: NShahed Shaikh <Shahed.Shaikh@cavium.com> Signed-off-by: NAriel Elior <ariel.elior@cavium.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shahed Shaikh 提交于
Add support for `ndo_set_vf_spoofchk' to allow PF control over its VF spoof-checking configuration. Signed-off-by: NShahed Shaikh <shahed.shaikh@cavium.com> Signed-off-by: NAriel Elior <ariel.elior@cavium.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 21 9月, 2018 1 次提交
-
-
由 Davide Caratti 提交于
bnxt offload code currently supports only 'push' and 'pop' operation: let .ndo_setup_tc() return -EOPNOTSUPP if VLAN 'modify' action is configured. Fixes: 2ae7408f ("bnxt_en: bnxt: add TC flower filter offload support") Signed-off-by: NDavide Caratti <dcaratti@redhat.com> Acked-by: NSathya Perla <sathya.perla@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 20 9月, 2018 1 次提交
-
-
由 YueHaibing 提交于
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t', which is a typedef for an enum type, so make sure the implementation in this driver has returns 'netdev_tx_t' value, and change the function return type to netdev_tx_t. Found by coccinelle. Signed-off-by: NYueHaibing <yuehaibing@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 19 9月, 2018 1 次提交
-
-
由 zhong jiang 提交于
Fix the following compile warning: drivers/net/ethernet/broadcom/bnxt/bnxt_devlink.c:49:5: warning: nvm_param.dir_type may be used uninitialized in this function [-Wmaybe-uninitialized] if (nvm_param.dir_type == BNXT_NVM_PORT_CFG) Signed-off-by: Nzhong jiang <zhongjiang@huawei.com> Acked-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 17 9月, 2018 1 次提交
-
-
由 Michael Chan 提交于
The recent commit to always forward the VF MAC address to the PF for approval may not work if the PF driver or the firmware is older. This will cause the VF driver to fail during probe: bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): hwrm req_type 0xf seq id 0x5 error 0xffff bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): VF MAC address 00:00:17:02:05:d0 not approved by the PF bnxt_en 0000:00:03.0: Unable to initialize mac address. bnxt_en: probe of 0000:00:03.0 failed with error -99 We fix it by treating the error as fatal only if the VF MAC address is locally generated by the VF. Fixes: 707e7e96 ("bnxt_en: Always forward VF MAC address to the PF.") Reported-by: NSeth Forshee <seth.forshee@canonical.com> Reported-by: NSiwei Liu <loseweigh@gmail.com> Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 14 9月, 2018 1 次提交
-
-
由 Gustavo A. R. Silva 提交于
Replace "fallthru" with a proper "fall through" annotation. This fix is part of the ongoing efforts to enabling -Wimplicit-fallthrough Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 9月, 2018 4 次提交
-
-
由 zhong jiang 提交于
DIV_ROUND_UP has implemented the code-opened function. Therefore, just replace the implementation with DIV_ROUND_UP. Signed-off-by: Nzhong jiang <zhongjiang@huawei.com> Acked-by: NTariq Toukan <tariqt@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
Rather than have MAC drivers open code the test, add a helper in phylib. This will help when we change the type of phydev->supported. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
ethtool can be used to enable/disable pause. Add a helper to configure the PHY when Pause is supported. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
ethtool can be used to enable/disable pause. Add a helper to configure the PHY when asym pause is supported. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-