In case np_thread state is in RESET/SHUTDOWN/EXIT states,
no point for isert to stall there as we may get a hang in
case no one will wake it up later.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

When the target is in stop stage, iSER transport initiates RDMA disconnects.
The iSER initiator may wish to establish a new connection over the
still existing network portal. In this case iSER transport should not
accept and resume new RDMA connections. In order to learn that, iscsi_np
is added with enabled flag so the iSER transport can check when deciding
weather to accept and resume a new connection request.

The iscsi_np is enabled after successful transport setup, and disabled
before iscsi_np login threads are cleaned up.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

RDMA CM and iSCSI target flows are asynchronous and completely
uncorrelated. Relying on the fact that iscsi_accept_np will be called
after CM connection request event and will wait for it is a mistake.

When attempting to login to a few targets this flow is racy and
unpredictable, but for parallel login to dozens of targets will
race and hang every time.

The correct synchronizing mechanism in this case is pending on
a semaphore rather than a wait_for_event. We keep the pending
interruptible for iscsi_np cleanup stage.

(Squash patch to remove dead code into parent - nab)
Reported-by: NSlava Shwartsman <valyushash@gmail.com>
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Should be adding list_add_tail($new, $head) and not
the other way around.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

In order to support local WRITE_INSERT + READ_STRIP operations for
non PI enabled fabrics, the fabric driver needs to be able signal
what protection offload operations are supported.

This is done at session initialization time so the modes can be
signaled by individual se_wwn + se_portal_group endpoints, as well
as optionally across different transports on the same endpoint.

For iser-target, set TARGET_PROT_ALL if the underlying ib_device
has already signaled PI offload support, and allow this to be
exposed via a new iscsit_transport->iscsit_get_sup_prot_ops()
callback.

For loopback, set TARGET_PROT_ALL to signal SCSI initiator mode
operation.

For all other drivers, set TARGET_PROT_NORMAL to disable fabric
level PI.

Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Fastreg is mandatory for signature, so if the
device doesn't support it we don't need to use it.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch fixes a bug where outstanding RDMA_READs with WRITE_PENDING
status require an extra target_put_sess_cmd() in isert_put_cmd() code
when called from isert_cq_tx_comp_err() + isert_cq_drain_comp_llist()
context during session shutdown.

The extra kref PUT is required so that transport_generic_free_cmd()
invokes the last target_put_sess_cmd() -> target_release_cmd_kref(),
which will complete(&se_cmd->cmd_wait_comp) the outstanding se_cmd
descriptor with WRITE_PENDING status, and awake the completion in
target_wait_for_sess_cmds() to invoke TFO->release_cmd().

The bug was manifesting itself in target_wait_for_sess_cmds() where
a se_cmd descriptor with WRITE_PENDING status would end up sleeping
indefinately.
Acked-by: NSagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Now that TASK_ABORTED status is not generated for all cases by
TMR ABORT_TASK + LUN_RESET, a new TFO->abort_task() caller is
necessary in order to give fabric drivers a chance to unmap
hardware / software resources before the se_cmd descriptor is
released via the normal TFO->release_cmd() codepath.

This patch adds TFO->aborted_task() in core_tmr_abort_task()
in place of the original transport_send_task_abort(), and
also updates all fabric drivers to implement this caller.

The fabric drivers that include changes to perform cleanup
via ->aborted_task() are:

  - iscsi-target
  - iser-target
  - srpt
  - tcm_qla2xxx

The fabric drivers that currently set ->aborted_task() to
NOPs are:

  - loopback
  - tcm_fc
  - usb-gadget
  - sbp-target
  - vhost-scsi

For the latter five, there appears to be no additional cleanup
required before invoking TFO->release_cmd() to release the
se_cmd descriptor.

v2 changes:
  - Move ->aborted_task() call into transport_cmd_finish_abort (Alex)

Cc: Alex Leung <amleung21@yahoo.com>
Cc: Mark Rustad <mark.d.rustad@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Vu Pham <vu@mellanox.com>
Cc: Chris Boot <bootc@bootc.net>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch changes isert_conn_create_fastreg_pool() to follow
logic in iscsi_target_locate_portal() for determining how many
FRMR descriptors to allocate based upon the number of possible
per-session command slots that are available.

This addresses an OOPs in isert_reg_rdma() where due to the
use of ISCSI_DEF_XMIT_CMDS_MAX could end up returning a bogus
fast_reg_descriptor when the number of active tags exceeded
the original hardcoded max.

Note this also includes moving isert_conn_create_fastreg_pool()
from isert_connect_request() to isert_put_login_tx() before
posting the final Login Response PDU in order to determine the
se_nacl->queue_depth (eg: number of tags) per session the target
will be enforcing.

v2 changes:
  - Move isert_conn->conn_fr_pool list_head init into
    isert_conn_request()
v3 changes:
  - Drop unnecessary list_empty() check in isert_reg_rdma()
    (Sagi)

Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

If during data-transfer a data-integrity error was detected we
must fail the command with CHECK_CONDITION and not execute
the command.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Reported-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Remove code duplication from RDMA_READ and RDMA_WRITE
completions that do basically the same check.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

If protection is involved, iSER target must wait for
completion of RDMA_READ before sending SCSI response.
So we must consider that when calculating post_send_buf_count
additions, also when processing good/error completions.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

As REG_SIG_MR work request and it's LOCAL_INVALIDATE are
not accounted in post_send_buf_count we must color these
with ISER_FASTREG_LI_WRID in order to process their error
completions when the QP flushes.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

In case the Target core passed transport T10 protection
operation:

1. Register data buffer (data memory region)
2. Register protection buffer if exsists (prot memory region)
3. Register signature region (signature memory region)
   - use work request IB_WR_REG_SIG_MR
4. Execute RDMA
5. Upon RDMA completion check the signature status
   - if succeeded send good SCSI response
   - if failed send SCSI bad response with appropriate sense buffer

(Fix up compile error in isert_reg_sig_mr, and fix up incorrect
 se_cmd->prot_type -> TARGET_PROT_NORMAL comparision - nab)
(Fix failed sector assignment in isert_completion_rdma_* - Sagi + nab)
(Fix enum assignements for protection type - Sagi)
(Fix devision on 32-bit in isert_completion_rdma_* - Sagi + Fengguang)
(Fix context change for v3.14-rc6 code - nab)
(Fix iscsit_build_rsp_pdu inc_statsn flag usage - nab)
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

In case of protected transactions, we will need to check the
protection status of the transaction before sending SCSI response.
So be ready for RDMA_WRITE completions. currently we don't ask
for these completions, but for T10-PI we will.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Introduce pi_context to hold relevant RDMA protection resources.
We eliminate data_key_valid boolean and replace it with indicators
container to indicate:
- Is the descriptor protected (registered via signature MR)
- Is the data_mr key valid (can spare LOCAL_INV WR)
- Is the prot_mr key valid (can spare LOCAL_INV WR)
- Is the sig_mr key valid (can spare LOCAL_INV WR)

Upon connection establishment check if network portal is T10-PI
enabled and allocate T10-PI resources if necessary, allocate
signature enabled memory regions and mark connection queue-pair
as signature enabled.

(Fix context change for v3.14-rc6 code - nab)
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

export map/unmap data buffer to a routine that may
be used in various places in the code and keep the
mapping data in a designated descriptor. Also, let
isert_fast_reg_mr to decide weather to use global
MR or do fast registration.

This commit does not change any functionality.

(Fix context change for v3.14-rc6 code - nab)
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch addresses a number of active I/O shutdown issues
related to isert_cmd descriptors being leaked that are part
of a completion interrupt coalescing batch.

This includes adding logic in isert_cq_tx_comp_err() to
drain any associated tx_desc->comp_llnode_batch, as well
as isert_cq_drain_comp_llist() to drain any associated
isert_conn->conn_comp_llist.

Also, set tx_desc->llnode_active in isert_init_send_wr()
in order to determine when work requests need to be skipped
in isert_cq_tx_work() exception path code.

Finally, update isert_init_send_wr() to only allow interrupt
coalescing when ISER_CONN_UP.
Acked-by: NSagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.13+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch changes IB_WR_FAST_REG_MR + IB_WR_LOCAL_INV related
work requests to include a ISER_FRWR_LI_WRID value in order to
signal isert_cq_tx_work() that these requests should be ignored.

This is necessary because even though IB_SEND_SIGNALED is not
set for either work request, during a QP failure event the work
requests will be returned with exception status from the TX
completion queue.

v2 changes:
 - Rename ISER_FRWR_LI_WRID -> ISER_FASTREG_LI_WRID (Sagi)
Acked-by: NSagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch fixes the incorrect setting of ->post_send_buf_count
related to RDMA WRITEs + READs where isert_rdma_rw->send_wr_num
was not being taken into account.

This includes incrementing ->post_send_buf_count within
isert_put_datain() + isert_get_dataout(), decrementing within
__isert_send_completion() + isert_response_completion(), and
clearing wr->send_wr_num within isert_completion_rdma_read()

This is necessary because even though IB_SEND_SIGNALED is
not set for RDMA WRITEs + READs, during a QP failure event
the work requests will be returned with exception status
from the TX completion queue.
Acked-by: NSagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch addresses a couple of different hug shutdown issues
related to wait_event() + isert_conn->state.  First, it changes
isert_conn->conn_wait + isert_conn->conn_wait_comp_err from
waitqueues to completions, and sets ISER_CONN_TERMINATING from
within isert_disconnect_work().

Second, it splits isert_free_conn() into isert_wait_conn() that
is called earlier in iscsit_close_connection() to ensure that
all outstanding commands have completed before continuing.

Finally, it breaks isert_cq_comp_err() into seperate TX / RX
related code, and adds logic in isert_cq_rx_comp_err() to wait
for outstanding commands to complete before setting ISER_CONN_DOWN
and calling complete(&isert_conn->conn_wait_comp_err).
Acked-by: NSagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

There are a handful of uses of list_empty() for cmd->i_conn_node
within iser-target code that expect to return false once a cmd
has been removed from the per connect list.

This patch changes all uses of list_del -> list_del_init in order
to ensure that list_empty() returns false as expected.
Acked-by: NSagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch fixes a memory leak for fr_desc upon failure of
isert_create_fr_desc() in isert_conn_create_fastreg_pool()
code.

As reported by Coverity 1166659:

*** CID 1166659:  Resource leak  (RESOURCE_LEAK)
/drivers/infiniband/ulp/isert/ib_isert.c: 470 in isert_conn_create_fastreg_pool()
464                      isert_conn, isert_conn->conn_fr_pool_size);
465
466             return 0;
467
468     err:
469             isert_conn_free_fastreg_pool(isert_conn);
>>>     CID 1166659:  Resource leak  (RESOURCE_LEAK)
>>>     Variable "fr_desc" going out of scope leaks the storage it points to.
470             return ret;
471     }
472
473     static int
474     isert_connect_request(struct rdma_cm_id *cma_id, struct rdma_cm_event *event)
475     {

Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch propigates the use of task state bitmask now used by
percpu_ida_alloc() up the iscsi-target callchain, replacing the
use of GFP_ATOMIC for TASK_RUNNING, and GFP_KERNEL for
TASK_INTERRUPTIBLE.

Also, drop the unnecessary gfp_t parameter to isert_allocate_cmd(),
and just pass TASK_INTERRUPTIBLE into iscsit_allocate_cmd().
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This routine may help for protection registration as well.
This patch does not change any functionality.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This routine may be called both by fast registration
descriptors for data and for integrity buffers.

This patch does not change any functionality.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Use fast registration lingo. fast registration will
also incorporate signature/DIF registration.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

It is more correct to seperate connections protection domains
and dma_mr handles. protection information support requires to
do so.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch moves INIT_WORK setup for cq_desc->cq_[rx,tx]_work into
isert_create_device_ib_res(), instead of being done each callback
invocation in isert_cq_[rx,tx]_callback().

This also fixes a 'INFO: trying to register non-static key' warning
when cancel_work_sync() is called before INIT_WORK has setup the
struct work_struct.
Reported-by: NOr Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch avoids a duplicate iscsit_increment_maxcmdsn() call for
ISER_IB_RDMA_WRITE within isert_map_rdma() + isert_reg_rdma_frwr(),
which will already be occuring once during isert_put_datain() ->
iscsit_build_rsp_pdu() operation.

It also removes the local conn->stat_sn assignment + increment,
and changes the third parameter to iscsit_build_rsp_pdu() to
signal this should be done by iscsi_target_mode code.
Tested-by: NMoussa Ba <moussaba@micron.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch changes isert_reg_rdma_frwr() to not use FRMR for single
dma entry requests from small I/Os, in order to avoid the associated
memory registration overhead.

Using DMA MR is sufficient here for the single dma entry requests,
and addresses a >= v3.12 performance regression.
Signed-off-by: NVu Pham <vu@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds support for completion interrupt coalescing that
allows only every ISERT_COMP_BATCH_COUNT (8) to set IB_SEND_SIGNALED,
thus avoiding completion interrupts for every posted iser_tx_desc.

The batch processing is done using a per isert_conn llist that once
IB_SEND_SIGNALED has been set is saved to tx_desc->comp_llnode_batch,
and completion processing of previously posted iser_tx_descs is done
in a single shot from within isert_send_completion() code.

Note this is only done for response PDUs from ISCSI_OP_SCSI_CMD, and
all other control type of PDU responses will force an implicit batch
drain to occur.

Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch changes isert_connect_release() to correctly check for
the existence struct isert_device *device before checking for
isert_device->use_frwr.
Signed-off-by: NVu Pham <vu@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Update copyright ownership/year information for target-core,
loopback, iscsi-target, tcm_qla2xx, vhost and iser-target.
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This model was introduced in 00f7ec36 "RDMA/core: Add memory
management extensions support" and works when the IB device
supports the IB_DEVICE_MEM_MGT_EXTENSIONS capability.

Upon creating the isert device, ib_isert will test whether the HCA
supports FRWR. If supported then set the flag and assign
function pointers that handle fast registration and deregistration
of appropriate resources (fast_reg descriptors).

When new connection coming in, ib_isert will check frwr flag and
create frwr resouces, if fail to do it will switch back to
old model of using global dma key and turn off the frwr support.

Registration is done using posting IB_WR_FAST_REG_MR to the QP and
invalidations using posting IB_WR_LOCAL_INV.
Signed-off-by: NVu Pham <vu@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Current driver uses global dma key to register the memory pointed
by sg list provided by the target core.

This is the preparation step for adding more methods like fast
path memory registration, make the reg/unreg calls be function
pointers.
Signed-off-by: NVu Pham <vu@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

isert_put_datain() and isert_get_dataout() share a lot of code
in rdma wr processing, move this common code to a shared function.

Use isert_unmap_cmd to cleanup for RDMA_READ completion.
Remove duplicate field in isert_cmd and isert_rdma_wr structs
Change misc debug messages to track isert_cmd
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NVu Pham <vu@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This command converts iscsi/isert-target to use allocations based on
iscsit_transport->priv_size within iscsit_allocate_cmd(), instead of
using an embedded isert_cmd->iscsi_cmd.

This includes removing iscsit_transport->alloc_cmd() usage, along
with updating isert-target code to use iscsit_priv_cmd().

Also, remove left-over iscsit_transport->release_cmd() usage for
direct calls to iscsit_release_cmd(), and drop the now unused
lio_cmd_cache and isert_cmd_cache.

Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: NNicholas Bellinger <nab@daterainc.com>

This patch updates iser-target code to support login negotiation
multi-plexing.  This includes only using isert_conn->conn_login_comp
for the first login request PDU, pushing the subsequent processing
to iscsi_conn->login_work -> iscsi_target_do_login_rx(), and turning
isert_get_login_rx() into a NOP.

v3 changes:
   - Drop unnecessary LOGIN_FLAGS_READ_ACTIVE bit set in
     isert_rx_login_req()
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>