Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 02 12月, 2016 4 次提交
  3. 17 11月, 2016 2 次提交
  5. 08 11月, 2016 1 次提交
  7. 01 11月, 2016 1 次提交
  9. 29 10月, 2016 1 次提交
  11. 28 10月, 2016 3 次提交
  13. 24 10月, 2016 1 次提交
  15. 14 10月, 2016 6 次提交
  17. 22 8月, 2016 2 次提交
  19. 16 8月, 2016 1 次提交
  21. 10 8月, 2016 1 次提交
  23. 19 7月, 2016 2 次提交
    • L
      drm/i915: Enable polling when we don't have hpd · 84c8e096
      由 Lyude 提交于 
      Unfortunately, there's two situations where we lose hpd right now:
- Runtime suspend
- When we've shut off all of the power wells on Valleyview/Cherryview

While it would be nice if this didn't cause issues, this has the
ability to get us in some awkward states where a user won't be able to
get their display to turn on. For instance; if we boot a Valleyview
system without any monitors connected, it won't need any of it's power
wells and thus shut them off. Since this causes us to lose HPD, this
means that unless the user knows how to ssh into their machine and do a
manual reprobe for monitors, none of the monitors they connect after
booting will actually work.

Eventually we should come up with a better fix then having to enable
polling for this, since this makes rpm a lot less useful, but for now
the infrastructure in i915 just isn't there yet to get hpd in these
situations.

Changes since v1:
 - Add comment explaining the addition of the if
   (!mode_config->poll_running) in intel_hpd_init()
 - Remove unneeded if (!dev->mode_config.poll_enabled) in
   i915_hpd_poll_init_work()
 - Call to drm_helper_hpd_irq_event() after we disable polling
 - Add cancel_work_sync() call to intel_hpd_cancel_work()

Changes since v2:
 - Apparently dev->mode_config.poll_running doesn't actually reflect
   whether or not a poll is currently in progress, and is actually used
   for dynamic module paramter enabling/disabling. So now we instead
   keep track of our own poll_running variable in dev_priv->hotplug
 - Clean i915_hpd_poll_init_work() a little bit

Changes since v3:
 - Remove the now-redundant connector loop in intel_hpd_init(), just
   rely on intel_hpd_poll_enable() for setting connector->polled
   correctly on each connector
 - Get rid of poll_running
 - Don't assign enabled in i915_hpd_poll_init_work before we actually
   lock dev->mode_config.mutex
 - Wrap enabled assignment in i915_hpd_poll_init_work() in READ_ONCE()
   for doc purposes
 - Do the same for dev_priv->hotplug.poll_enabled with WRITE_ONCE in
   intel_hpd_poll_enable()
 - Add some comments about racing not mattering in intel_hpd_poll_enable

Changes since v4:
 - Rename intel_hpd_poll_enable() to intel_hpd_poll_init()
 - Drop the bool argument from intel_hpd_poll_init()
 - Remove redundant calls to intel_hpd_poll_init()
 - Rename poll_enable_work to poll_init_work
 - Add some kerneldoc for intel_hpd_poll_init()
 - Cross-reference intel_hpd_poll_init() in intel_hpd_init()
 - Just copy the loop from intel_hpd_init() in intel_hpd_poll_init()

Changes since v5:
 - Minor kerneldoc nitpicks

Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NLyude <cpaul@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 19625e85)
      84c8e096
    • L
      drm/i915/vlv: Reset the ADPA in vlv_display_power_well_init() · 4c732e6e
      由 Lyude 提交于 
      While VGA hotplugging worked(ish) before, it looks like that was mainly
because we'd unintentionally enable it in
valleyview_crt_detect_hotplug() when we did a force trigger. This
doesn't work reliably enough because whenever the display powerwell on
vlv gets disabled, the values set in VLV_ADPA get cleared and
consequently VGA hotplugging gets disabled. This causes bugs such as one
we found on an Intel NUC, where doing the following sequence of
hotplugs:

      - Disconnect all monitors
      - Connect VGA
      - Disconnect VGA
      - Connect HDMI

Would result in VGA hotplugging becoming disabled, due to the powerwells
getting toggled in the process of connecting HDMI.

Changes since v3:
 - Expose intel_crt_reset() through intel_drv.h and call that in
   vlv_display_power_well_init() instead of
   encoder->base.funcs->reset(&encoder->base);

Changes since v2:
 - Use intel_encoder structs instead of drm_encoder structs

Changes since v1:
 - Instead of handling the register writes ourself, we just reuse
   intel_crt_detect()
 - Instead of resetting the ADPA during display IRQ installation, we now
   reset them in vlv_display_power_well_init()

Cc: stable@vger.kernel.org
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NLyude <cpaul@redhat.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Rebase over dev_priv/drm_device embedding.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 9504a892)
      4c732e6e
  25. 15 7月, 2016 2 次提交
    • L
      drm/i915: Enable polling when we don't have hpd · 19625e85
      由 Lyude 提交于 
      Unfortunately, there's two situations where we lose hpd right now:
- Runtime suspend
- When we've shut off all of the power wells on Valleyview/Cherryview

While it would be nice if this didn't cause issues, this has the
ability to get us in some awkward states where a user won't be able to
get their display to turn on. For instance; if we boot a Valleyview
system without any monitors connected, it won't need any of it's power
wells and thus shut them off. Since this causes us to lose HPD, this
means that unless the user knows how to ssh into their machine and do a
manual reprobe for monitors, none of the monitors they connect after
booting will actually work.

Eventually we should come up with a better fix then having to enable
polling for this, since this makes rpm a lot less useful, but for now
the infrastructure in i915 just isn't there yet to get hpd in these
situations.

Changes since v1:
 - Add comment explaining the addition of the if
   (!mode_config->poll_running) in intel_hpd_init()
 - Remove unneeded if (!dev->mode_config.poll_enabled) in
   i915_hpd_poll_init_work()
 - Call to drm_helper_hpd_irq_event() after we disable polling
 - Add cancel_work_sync() call to intel_hpd_cancel_work()

Changes since v2:
 - Apparently dev->mode_config.poll_running doesn't actually reflect
   whether or not a poll is currently in progress, and is actually used
   for dynamic module paramter enabling/disabling. So now we instead
   keep track of our own poll_running variable in dev_priv->hotplug
 - Clean i915_hpd_poll_init_work() a little bit

Changes since v3:
 - Remove the now-redundant connector loop in intel_hpd_init(), just
   rely on intel_hpd_poll_enable() for setting connector->polled
   correctly on each connector
 - Get rid of poll_running
 - Don't assign enabled in i915_hpd_poll_init_work before we actually
   lock dev->mode_config.mutex
 - Wrap enabled assignment in i915_hpd_poll_init_work() in READ_ONCE()
   for doc purposes
 - Do the same for dev_priv->hotplug.poll_enabled with WRITE_ONCE in
   intel_hpd_poll_enable()
 - Add some comments about racing not mattering in intel_hpd_poll_enable

Changes since v4:
 - Rename intel_hpd_poll_enable() to intel_hpd_poll_init()
 - Drop the bool argument from intel_hpd_poll_init()
 - Remove redundant calls to intel_hpd_poll_init()
 - Rename poll_enable_work to poll_init_work
 - Add some kerneldoc for intel_hpd_poll_init()
 - Cross-reference intel_hpd_poll_init() in intel_hpd_init()
 - Just copy the loop from intel_hpd_init() in intel_hpd_poll_init()

Changes since v5:
 - Minor kerneldoc nitpicks

Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NLyude <cpaul@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      19625e85
    • L
      drm/i915/vlv: Reset the ADPA in vlv_display_power_well_init() · 9504a892
      由 Lyude 提交于 
      While VGA hotplugging worked(ish) before, it looks like that was mainly
because we'd unintentionally enable it in
valleyview_crt_detect_hotplug() when we did a force trigger. This
doesn't work reliably enough because whenever the display powerwell on
vlv gets disabled, the values set in VLV_ADPA get cleared and
consequently VGA hotplugging gets disabled. This causes bugs such as one
we found on an Intel NUC, where doing the following sequence of
hotplugs:

      - Disconnect all monitors
      - Connect VGA
      - Disconnect VGA
      - Connect HDMI

Would result in VGA hotplugging becoming disabled, due to the powerwells
getting toggled in the process of connecting HDMI.

Changes since v3:
 - Expose intel_crt_reset() through intel_drv.h and call that in
   vlv_display_power_well_init() instead of
   encoder->base.funcs->reset(&encoder->base);

Changes since v2:
 - Use intel_encoder structs instead of drm_encoder structs

Changes since v1:
 - Instead of handling the register writes ourself, we just reuse
   intel_crt_detect()
 - Instead of resetting the ADPA during display IRQ installation, we now
   reset them in vlv_display_power_well_init()

Cc: stable@vger.kernel.org
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NLyude <cpaul@redhat.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Rebase over dev_priv/drm_device embedding.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      9504a892
  27. 05 7月, 2016 1 次提交
  29. 01 7月, 2016 1 次提交
  31. 30 6月, 2016 4 次提交
  33. 23 6月, 2016 1 次提交
  35. 13 6月, 2016 3 次提交
  37. 06 6月, 2016 1 次提交
  39. 24 5月, 2016 2 次提交