Including <linux/in.h> and <netinet/in.h> in the dependencies breaks
compilation of trinity due to multiple definitions. <linux/in.h> is only
used in <linux/icmp.h> to provide the definition of the struct in_addr,
but this can be substituted out by using the datatype __be32.
Signed-off-by: NAndreas Roeseler <andreas.a.roeseler@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clang warns that proto in rmnet_map_v5_checksum_uplink_packet() might be
used uninitialized:

drivers/net/ethernet/qualcomm/rmnet/rmnet_map_data.c:283:14: warning:
variable 'proto' is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
                } else if (skb->protocol == htons(ETH_P_IPV6)) {
                           ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_data.c:295:36: note:
uninitialized use occurs here
                check = rmnet_map_get_csum_field(proto, trans);
                                                 ^~~~~
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_data.c:283:10: note:
remove the 'if' if its condition is always true
                } else if (skb->protocol == htons(ETH_P_IPV6)) {
                       ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_data.c:270:11: note:
initialize the variable 'proto' to silence this warning
                u8 proto;
                        ^
                         = '\0'
1 warning generated.

This is technically a false positive because there is an if statement
above this one that checks skb->protocol for not being either
ETH_P_IP{,V6}. However, it is more obvious to sink that into the if
statement as an else branch, which makes the code clearer and fixes the
warning.

At the same time, move the "IS_ENABLED(CONFIG_IPV6)" into the else if
condition so that the else branch of the preprocessor conditional can
be shared, since there is no build failure with CONFIG_IPV6 disabled.

Fixes: b6e5d27e ("net: ethernet: rmnet: Add support for MAPv5 egress packets")
Link: https://github.com/ClangBuiltLinux/linux/issues/1390Signed-off-by: NNathan Chancellor <nathan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

clang points out that ret in ks8851_read_selftest() is set but unused:

drivers/net/ethernet/micrel/ks8851_common.c:1028:6: warning: variable
'ret' set but not used [-Wunused-but-set-variable]
        int ret = 0;
            ^
1 warning generated.

The return code of this function has never been checked so just remove
ret and make the function return void.

Fixes: 3ba81f3e ("net: Micrel KS8851 SPI network driver")
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NNathan Chancellor <nathan@kernel.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add description for parameters of htb_add_to_id_tree() to fix
gcc W=1 warnings:
net/sched/sch_htb.c:282: warning: Function parameter or member 'root' not described in 'htb_add_to_id_tree'
net/sched/sch_htb.c:282: warning: Function parameter or member 'cl' not described in 'htb_add_to_id_tree'
net/sched/sch_htb.c:282: warning: Function parameter or member 'prio' not described in 'htb_add_to_id_tree'
Signed-off-by: NYu Kuai <yukuai3@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable ret is being initialized with a value that is never read,
it is being updated later on.  The assignment is redundant and can be
removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than open-coding the phy_modify_changed() sequence, use this
helper in marvell_set_polarity().
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NMarek Behún <kabel@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alex Elder says:

====================
net: ipa: support inline checksum offload

Inline offload--required for checksum offload support on IPA version
4.5 and above--is now supported by the RMNet driver:
  https://lore.kernel.org/netdev/162259440606.2786.10278242816453240434.git-patchwork-notify@kernel.org/

Add support for it in the IPA driver, and revert the commit that
disabled it pending acceptance of the RMNet code.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit c88c34fc.

The RMNet driver now supports inline checksum offload.
Signed-off-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Starting with IPA v4.5, IP payload checksum offload is implemented
differently.

Prior to v4.5, the IPA hardware appends an rmnet_map_dl_csum_trailer
structure to each packet if checksum offload is enabled in the
download direction (modem->AP).  In the upload direction (AP->modem)
a rmnet_map_ul_csum_header structure is prepended before each sent
packet.

Starting with IPA v4.5, checksum offload is implemented using a
single new rmnet_map_v5_csum_header structure which sits between
the QMAP header and the packet data.  The same header structure
is used in both directions.

The new header contains a header type (CSUM_OFFLOAD); a checksum
flag; and a flag indicating whether any other headers follow this
one.  The checksum flag indicates whether the hardware should
compute (and insert) the checksum on a sent packet.  On a received
packet the checksum flag indicates whether the hardware confirms the
checksum value in the payload is correct.
Signed-off-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
This series provides misc updates for mlx5 drivers.
For more information please see tag log below.

Please pull and let me know if there is any problem.

mlx5-updates-2021-06-03

This series contains misc updates for mlx5 driver

1) Alaa disables advanced features when kdump mode to save on memory
2) Jakub counts all link flap events
3) Meir adds support for IPoIB NDR speed
4) Various misc cleanup
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NÍñigo Huguet <ihuguet@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

OFLD and CTRL TX queues can be stopped if there is no room in
their DMA rings. If this happens, they're tried to be restarted
later after having made some room in the corresponding ring.

The tasks of restarting these queues were triggered using
tasklets, but they can be replaced for workqueue works, getting
them out of softirq context.

This queues stop/restart probably doesn't happen often and they
can be quite lengthy because they try to send all pending skbs.
Moreover, given that probably the ring is not empty yet, so the
DMA still has work to do, we don't need to be so fast to justify
using tasklets/softirq instead of running in a thread.
Signed-off-by: NÍñigo Huguet <ihuguet@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch aims to improve the situation when reordering and loss are
ocurring in the same flight of packets.

Previously the reordering would first induce a spurious recovery, then
the subsequent ACK may undo the cwnd (based on the timestamps e.g.).
However the current loss recovery does not proceed to invoke
RACK to install a reordering timer. If some packets are also lost, this
may lead to a long RTO-based recovery. An example is
https://groups.google.com/g/bbr-dev/c/OFHADvJbTEI

The solution is to after reverting the recovery, always invoke RACK
to either mount the RACK timer to fast retransmit after the reordering
window, or restarts the recovery if new loss is identified. Hence
it is possible the sender may go from Recovery to Disorder/Open to
Recovery again in one ACK.
Reported-by: Nmingkun bian <bianmingkun@gmail.com>
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Silence this warning by using strscpy_pad() directly:

drivers/net/bonding/bond_main.c:4877:3: warning: 'strncpy' specified bound 16 equals destination size [-Wstringop-truncation]
    4877 |   strncpy(params->primary, primary, IFNAMSIZ);
         |   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Additionally replace other strncpy() uses, as it is considered deprecated:
https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-stringsReported-by: Nkernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202102150705.fdR6obB0-lkp@intel.comAcked-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use strscpy_pad() instead of strncpy() which is considered deprecated:
https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-stringsSigned-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shai Malin says:

====================
NVMeTCP Offload ULP

With the goal of enabling a generic infrastructure that allows NVMe/TCP
offload devices like NICs to seamlessly plug into the NVMe-oF stack, this
patch series introduces the nvme-tcp-offload ULP host layer, which will
be a new transport type called "tcp-offload" and will serve as an
abstraction layer to work with vendor specific nvme-tcp offload drivers.

NVMeTCP offload is a full offload of the NVMeTCP protocol, this includes
both the TCP level and the NVMeTCP level.

The nvme-tcp-offload transport can co-exist with the existing tcp and
other transports. The tcp offload was designed so that stack changes are
kept to a bare minimum: only registering new transports.
All other APIs, ops etc. are identical to the regular tcp transport.
Representing the TCP offload as a new transport allows clear and manageable
differentiation between the connections which should use the offload path
and those that are not offloaded (even on the same device).

The nvme-tcp-offload layers and API compared to nvme-tcp and nvme-rdma:

* NVMe layer: *

       [ nvme/nvme-fabrics/blk-mq ]
             |
        (nvme API and blk-mq API)
             |
             |
* Vendor agnostic transport layer: *

      [ nvme-rdma ] [ nvme-tcp ] [ nvme-tcp-offload ]
             |        |             |
           (Verbs)
             |        |             |
             |     (Socket)
             |        |             |
             |        |        (nvme-tcp-offload API)
             |        |             |
             |        |             |
* Vendor Specific Driver: *

             |        |             |
           [ qedr ]
                      |             |
                   [ qede ]
                                    |
                                  [ qedn ]

Performance:
============
With this implementation on top of the Marvell qedn driver (using the
Marvell FastLinQ NIC), we were able to demonstrate the following CPU
utilization improvement:

On AMD EPYC 7402, 2.80GHz, 28 cores:
- For 16K queued read IOs, 16jobs, 4qd (50Gbps line rate):
  Improved the CPU utilization from 15.1% with NVMeTCP SW to 4.7% with
  NVMeTCP offload.

On Intel(R) Xeon(R) Gold 5122 CPU, 3.60GHz, 16 cores:
- For 512K queued read IOs, 16jobs, 4qd (25Gbps line rate):
  Improved the CPU utilization from 16.3% with NVMeTCP SW to 1.1% with
  NVMeTCP offload.

In addition, we were able to demonstrate the following latency improvement:
- For 200K read IOPS (16 jobs, 16 qd, with fio rate limiter):
  Improved the average latency from 105 usec with NVMeTCP SW to 39 usec
  with NVMeTCP offload.

  Improved the 99.99 tail latency from 570 usec with NVMeTCP SW to 91 usec
  with NVMeTCP offload.

The end-to-end offload latency was measured from fio while running against
back end of null device.

Upstream plan:
==============
The RFC series "NVMeTCP Offload ULP and QEDN Device Driver"
https://lore.kernel.org/netdev/20210531225222.16992-1-smalin@marvell.com/
was designed in a modular way so that part 1 (nvme-tcp-offload) and
part 2 (qed) are independent and part 3 (qedn) depends on both parts 1+2.

- Part 1 (RFC patch 1-8): NVMeTCP Offload ULP
  The nvme-tcp-offload patches, will be sent to
  'linux-nvme@lists.infradead.org'.

- Part 2 (RFC patches 9-15): QED NVMeTCP Offload
  The qed infrastructure, will be sent to 'netdev@vger.kernel.org'.

Once part 1 and 2 are accepted:

- Part 3 (RFC patches 16-27): QEDN NVMeTCP Offload
  The qedn patches, will be sent to 'linux-nvme@lists.infradead.org'.

Marvell is fully committed to maintain, test, and address issues with
the new nvme-tcp-offload layer.

Usage:
======
With the Marvell NVMeTCP offload design, the network-device (qede) and the
offload-device (qedn) are paired on each port - Logically similar to the
RDMA model.
The user will interact with the network-device in order to configure
the ip/vlan. The NVMeTCP configuration is populated as part of the
nvme connect command.

Example:
Assign IP to the net-device (from any existing Linux tool):

    ip addr add 100.100.0.101/24 dev p1p1

This IP will be used by both net-device (qede) and offload-device (qedn).

In order to connect from "sw" nvme-tcp through the net-device (qede):

    nvme connect -t tcp -s 4420 -a 100.100.0.100 -n testnqn

In order to connect from "offload" nvme-tcp through the offload-device (qedn):

    nvme connect -t tcp_offload -s 4420 -a 100.100.0.100 -n testnqn

An alternative approach, and as a future enhancement that will not impact this
series will be to modify nvme-cli with a new flag that will determine
if "-t tcp" should be the regular nvme-tcp (which will be the default)
or nvme-tcp-offload.
Exmaple:
    nvme connect -t tcp -s 4420 -a 100.100.0.100 -n testnqn -[new flag]

Queue Initialization Design:
============================
The nvme-tcp-offload ULP module shall register with the existing
nvmf_transport_ops (.name = "tcp_offload"), nvme_ctrl_ops and blk_mq_ops.
The nvme-tcp-offload vendor driver shall register to nvme-tcp-offload ULP
with the following ops:
- claim_dev() - in order to resolve the route to the target according to
                the paired net_dev.
- create_queue() - in order to create offloaded nvme-tcp queue.

The nvme-tcp-offload ULP module shall manage all the controller level
functionalities, call claim_dev and based on the return values shall call
the relevant module create_queue in order to create the admin queue and
the IO queues.

IO-path Design:
===============
The nvme-tcp-offload shall work at the IO-level - the nvme-tcp-offload
ULP module shall pass the request (the IO) to the nvme-tcp-offload vendor
driver and later, the nvme-tcp-offload vendor driver returns the request
completion (the IO completion).
No additional handling is needed in between; this design will reduce the
CPU utilization as we will describe below.

The nvme-tcp-offload vendor driver shall register to nvme-tcp-offload ULP
with the following IO-path ops:
- send_req() - in order to pass the request to the handling of the
               offload driver that shall pass it to the vendor specific device.
- poll_queue()

Once the IO completes, the nvme-tcp-offload vendor driver shall call
command.done() that will invoke the nvme-tcp-offload ULP layer to
complete the request.

TCP events:
===========
The Marvell FastLinQ NIC HW engine handle all the TCP re-transmissions
and OOO events.

Teardown and errors:
====================
In case of NVMeTCP queue error the nvme-tcp-offload vendor driver shall
call the nvme_tcp_ofld_report_queue_err.
The nvme-tcp-offload vendor driver shall register to nvme-tcp-offload ULP
with the following teardown ops:
- drain_queue()
- destroy_queue()

The Marvell FastLinQ NIC HW engine:
====================================
The Marvell NIC HW engine is capable of offloading the entire TCP/IP
stack and managing up to 64K connections per PF, already implemented and
upstream use cases for this include iWARP (by the Marvell qedr driver)
and iSCSI (by the Marvell qedi driver).
In addition, the Marvell NIC HW engine offloads the NVMeTCP queue layer
and is able to manage the IO level also in case of TCP re-transmissions
and OOO events.
The HW engine enables direct data placement (including the data digest CRC
calculation and validation) and direct data transmission (including data
digest CRC calculation).

The Marvell qedn driver:
========================
The new driver will be added under "drivers/nvme/hw" and will be enabled
by the Kconfig "Marvell NVM Express over Fabrics TCP offload".
As part of the qedn init, the driver will register as a pci device driver
and will work with the Marvell fastlinQ NIC.
As part of the probe, the driver will register to the nvme_tcp_offload
(ULP) and to the qed module (qed_nvmetcp_ops) - similar to other
"qed_*_ops" which are used by the qede, qedr, qedf and qedi device
drivers.

nvme-tcp-offload Future work:
=============================
- NVMF_OPT_HOST_IFACE Support.

Changes since RFC v1:
=====================
- nvme-tcp-offload: Fix nvme_tcp_ofld_ops return values.
- nvme-tcp-offload: Remove NVMF_TRTYPE_TCP_OFFLOAD.
- nvme-tcp-offload: Add nvme_tcp_ofld_poll() implementation.
- nvme-tcp-offload: Fix nvme_tcp_ofld_queue_rq() to check map_sg() and
  send_req() return values.

Changes since RFC v2:
=====================
- nvme-tcp-offload: Fixes in controller and queue level (patches 3-6).
- qedn: Add the Marvell's NVMeTCP HW offload vendor driver init and probe
  (patches 8-11).

Changes since RFC v3:
=====================
- nvme-tcp-offload: Add the full implementation of the nvme-tcp-offload layer
  including the new ops: setup_ctrl(), release_ctrl(), commit_rqs() and new
  flows (ASYNC and timeout).
- nvme-tcp-offload: Add device maximums: max_hw_sectors, max_segments.
- nvme-tcp-offload: layer design and optimization changes.

Changes since RFC v4:
=====================
(Many thanks to Hannes Reinecke for his feedback)
- nvme_tcp_offload: Add num_hw_vectors in order to limit the number of queues.
- nvme_tcp_offload: Add per device private_data.
- nvme_tcp_offload: Fix header digest, data digest and tos initialization.

Changes since RFC v5:
=====================
(Many thanks to Sagi Grimberg for his feedback)
- nvme-fabrics: Expose nvmf_check_required_opts() globally (as a new patch).
- nvme_tcp_offload: Remove io-queues BLK_MQ_F_BLOCKING.
- nvme_tcp_offload: Fix the nvme_tcp_ofld_stop_queue (drain_queue) flow.
- nvme_tcp_offload: Fix the nvme_tcp_ofld_free_queue (destroy_queue) flow.
- nvme_tcp_offload: Change rwsem to mutex.
- nvme_tcp_offload: remove redundant fields.
- nvme_tcp_offload: Remove the "new" from setup_ctrl().
- nvme_tcp_offload: Remove the init_req() and commit_rqs() ops.
- nvme_tcp_offload: Minor fixes in nvme_tcp_ofld_create_ctrl() ansd
  nvme_tcp_ofld_free_queue().
- nvme_tcp_offload: Patch 8 (timeout and async) was squeashed into
  patch 7 (io level).

Changes since RFC v6:
=====================
- No changes in nvme_tcp_offload (only in qedn).
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this patch, we present the IO level functionality.
The nvme-tcp-offload shall work on the IO-level, meaning the
nvme-tcp-offload ULP module shall pass the request to the nvme-tcp-offload
vendor driver and shall expect for the request completion.
No additional handling is needed in between, this design will reduce the
CPU utilization as we will describe below.

The nvme-tcp-offload vendor driver shall register to nvme-tcp-offload ULP
with the following IO-path ops:
 - send_req - in order to pass the request to the handling of the offload
   driver that shall pass it to the vendor specific device
 - poll_queue

The vendor driver will manage the context from which the request will be
executed and the request aggregations.
Once the IO completed, the nvme-tcp-offload vendor driver shall call
command.done() that shall invoke the nvme-tcp-offload ULP layer for
completing the request.

This patch also add support for the nvme-tcp-offload timeout and
nvme-tcp-offload ASYNC flow.
Acked-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDean Balandin <dbalandin@marvell.com>
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NOmkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NHimanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this patch we implement queue level functionality.
The implementation is similar to the nvme-tcp module, the main
difference being that we call the vendor specific create_queue op which
creates the TCP connection, and NVMeTPC connection including
icreq+icresp negotiation.
Once create_queue returns successfully, we can move on to the fabrics
connect.
Acked-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDean Balandin <dbalandin@marvell.com>
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NOmkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Reviewed-by: NHimanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this patch, we implement controller level error handling and recovery.
Upon an error discovered by the ULP or reset controller initiated by the
nvme-core (using reset_ctrl workqueue), the ULP will initiate a controller
recovery which includes teardown and re-connect of all queues.
Acked-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NArie Gershberg <agershberg@marvell.com>
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NOmkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NHimanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this patch we implement controller level functionality including:
- create_ctrl.
- delete_ctrl.
- free_ctrl.

The implementation is similar to other nvme fabrics modules, the main
difference being that the nvme-tcp-offload ULP calls the vendor specific
claim_dev() op with the given TCP/IP parameters to determine which device
will be used for this controller.
Once found, the vendor specific device and controller will be paired and
kept in a controller list managed by the ULP.
Acked-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NArie Gershberg <agershberg@marvell.com>
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NOmkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Reviewed-by: NHimanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As part of create_ctrl(), it scans the registered devices and calls
the claim_dev op on each of them, to find the first devices that matches
the connection params. Once the correct devices is found (claim_dev
returns true), we raise the refcnt of that device and return that device
as the device to be used for ctrl currently being created.
Acked-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDean Balandin <dbalandin@marvell.com>
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NOmkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Reviewed-by: NHimanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nvmf_check_required_opts() is used to check if user provided opts has
the required_opts or not. if not, it will log which options are not
provided.

It can be leveraged by nvme-tcp-offload to check if provided opts are
supported by this specific vendor driver or not.

So expose nvmf_check_required_opts() globally.
Acked-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NOmkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move NVMF_ALLOWED_OPTS and NVMF_REQUIRED_OPTS definitions
to header file, so it can be used by the different HW devices.

NVMeTCP offload devices might have different limitations of the
allowed options, for example, a device that does not support all the
queue types. With tcp and rdma, only the nvme-tcp and nvme-rdma layers
handle those attributes and the HW devices do not create any limitations
for the allowed options.

An alternative design could be to add separate fields in
nvme_tcp_ofld_ops such as max_hw_sectors and max_segments that
we already have in this series.
Acked-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NArie Gershberg <agershberg@marvell.com>
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NOmkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Reviewed-by: NHimanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Acked-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch will present the structure for the NVMeTCP offload common
layer driver. This module is added under "drivers/nvme/host/" and future
offload drivers which will register to it will be placed under
"drivers/nvme/hw".
This new driver will be enabled by the Kconfig "NVM Express over Fabrics
TCP offload commmon layer".
In order to support the new transport type, for host mode, no change is
needed.

Each new vendor-specific offload driver will register to this ULP during
its probe function, by filling out the nvme_tcp_ofld_dev->ops and
nvme_tcp_ofld_dev->private_data and calling nvme_tcp_ofld_register_dev
with the initialized struct.

The internal implementation:
- tcp-offload.h:
  Includes all common structs and ops to be used and shared by offload
  drivers.

- tcp-offload.c:
  Includes the init function which registers as a NVMf transport just
  like any other transport.
Acked-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDean Balandin <dbalandin@marvell.com>
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NOmkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NHimanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jon Maloy says:

====================
tipc: some small cleanups

We make some minor code cleanups and improvements.

v2: Changed value of TIPC_ANY_SCOPE macro in patch #3
    to avoid compiler warning
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We introduce a new macro TIPC_ANY_SCOPE to make the handling of the
lookup scope value more comprehensible during multicast reception.

The (unchanged) rules go as follows:

1) Multicast messages sent from own node are delivered to all matching
   sockets on the own node, irrespective of their binding scope.

2) Multicast messages sent from other nodes arrive here because they
   have found TIPC_CLUSTER_SCOPE bindings emanating from this node.
   Those messages should be delivered to exactly those sockets, but not
   to local sockets bound with TIPC_NODE_SCOPE, since the latter
   obviously were not meant to be visible for those senders.

3) Group multicast/broadcast messages are delivered to the sockets with
   a binding scope matching exactly the lookup scope indicated in the
   message header, and nobody else.
Reviewed-by: NXin Long <lucien.xin@gmail.com>
Tested-by: NHoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: NJon Maloy <jmaloy@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We refactor tipc_sk_anc_data_recv() to make it slightly more
comprehensible, but also to facilitate application of some additions
to the code in a future commit.
Reviewed-by: NXin Long <lucien.xin@gmail.com>
Tested-by: NHoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: NJon Maloy <jmaloy@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We eliminate the redundant fields conn_type and conn_instance in
struct tipc_sock. On the connecting side, this information is already
present in the unused (after the connection is established) part of
the pre-allocated header, and on the accepting side, we put it there
when the new socket is created.
Reviewed-by: NXin Long <lucien.xin@gmail.com>
Tested-by: NHoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: NJon Maloy <jmaloy@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shai Malin says:

====================
QED NVMeTCP Offload

Intro:
======
This is the qed part of Marvell’s NVMeTCP offload series, shared as
RFC series "NVMeTCP Offload ULP and QEDN Device Drive".
This part is a standalone series, and is not dependent on other parts
of the RFC.
The overall goal is to add qedn as the offload driver for NVMeTCP,
alongside the existing offload drivers (qedr, qedi and qedf for rdma,
iscsi and fcoe respectively).

In this series we are making the necessary changes to qed to enable this
by exposing APIs for FW/HW initializations.

The qedn series (and required changes to NVMe stack) will be sent to the
linux-nvme mailing list.
I have included more details on the upstream plan under section with the
same name below.

The Series Patches:
===================
1. qed: Add TCP_ULP FW resource layout – replacing iSCSI when common
   with NVMeTCP.
2. qed: Add NVMeTCP Offload PF Level FW and HW HSI.
3. qed: Add NVMeTCP Offload Connection Level FW and HW HSI.
4. qed: Add support of HW filter block – enables redirecting NVMeTCP
   traffic to the dedicated PF.
5. qed: Add NVMeTCP Offload IO Level FW and HW HSI.
6. qed: Add NVMeTCP Offload IO Level FW Initializations.
7. qed: Add IP services APIs support –VLAN, IP routing and reserving
   TCP ports for the offload device.

The NVMeTCP Offload:
====================
With the goal of enabling a generic infrastructure that allows NVMe/TCP
offload devices like NICs to seamlessly plug into the NVMe-oF stack, this
patch series introduces the nvme-tcp-offload ULP host layer, which will
be a new transport type called "tcp-offload" and will serve as an
abstraction layer to work with vendor specific nvme-tcp offload drivers.

NVMeTCP offload is a full offload of the NVMeTCP protocol, this includes
both the TCP level and the NVMeTCP level.

The nvme-tcp-offload transport can co-exist with the existing tcp and
other transports. The tcp offload was designed so that stack changes are
kept to a bare minimum: only registering new transports.
All other APIs, ops etc. are identical to the regular tcp transport.
Representing the TCP offload as a new transport allows clear and manageable
differentiation between the connections which should use the offload path
and those that are not offloaded (even on the same device).

The nvme-tcp-offload layers and API compared to nvme-tcp and nvme-rdma:

* NVMe layer: *

       [ nvme/nvme-fabrics/blk-mq ]
             |
        (nvme API and blk-mq API)
             |
             |
* Vendor agnostic transport layer: *

      [ nvme-rdma ] [ nvme-tcp ] [ nvme-tcp-offload ]
             |        |             |
           (Verbs)
             |        |             |
             |     (Socket)
             |        |             |
             |        |        (nvme-tcp-offload API)
             |        |             |
             |        |             |
* Vendor Specific Driver: *

             |        |             |
           [ qedr ]
                      |             |
                   [ qede ]
                                    |
                                  [ qedn ]

Performance:
============
With this implementation on top of the Marvell qedn driver (using the
Marvell FastLinQ NIC), we were able to demonstrate the following CPU
utilization improvement:

On AMD EPYC 7402, 2.80GHz, 28 cores:
- For 16K queued read IOs, 16jobs, 4qd (50Gbps line rate):
  Improved the CPU utilization from 15.1% with NVMeTCP SW to 4.7% with
  NVMeTCP offload.

On Intel(R) Xeon(R) Gold 5122 CPU, 3.60GHz, 16 cores:
- For 512K queued read IOs, 16jobs, 4qd (25Gbps line rate):
  Improved the CPU utilization from 16.3% with NVMeTCP SW to 1.1% with
  NVMeTCP offload.

In addition, we were able to demonstrate the following latency improvement:
- For 200K read IOPS (16 jobs, 16 qd, with fio rate limiter):
  Improved the average latency from 105 usec with NVMeTCP SW to 39 usec
  with NVMeTCP offload.

  Improved the 99.99 tail latency from 570 usec with NVMeTCP SW to 91 usec
  with NVMeTCP offload.

The end-to-end offload latency was measured from fio while running against
back end of null device.

The Marvell FastLinQ NIC HW engine:
====================================
The Marvell NIC HW engine is capable of offloading the entire TCP/IP
stack and managing up to 64K connections per PF, already implemented and
upstream use cases for this include iWARP (by the Marvell qedr driver)
and iSCSI (by the Marvell qedi driver).
In addition, the Marvell NIC HW engine offloads the NVMeTCP queue layer
and is able to manage the IO level also in case of TCP re-transmissions
and OOO events.
The HW engine enables direct data placement (including the data digest CRC
calculation and validation) and direct data transmission (including data
digest CRC calculation).

The Marvell qedn driver:
========================
The new driver will be added under "drivers/nvme/hw" and will be enabled
by the Kconfig "Marvell NVM Express over Fabrics TCP offload".
As part of the qedn init, the driver will register as a pci device driver
and will work with the Marvell fastlinQ NIC.
As part of the probe, the driver will register to the nvme_tcp_offload
(ULP) and to the qed module (qed_nvmetcp_ops) - similar to other
"qed_*_ops" which are used by the qede, qedr, qedf and qedi device
drivers.

Upstream Plan:
=============
The RFC series "NVMeTCP Offload ULP and QEDN Device Driver"
https://lore.kernel.org/netdev/20210531225222.16992-1-smalin@marvell.com/
was designed in a modular way so that part 1 (nvme-tcp-offload) and
part 2 (qed) are independent and part 3 (qedn) depends on both parts 1+2.

- Part 1 (RFC patch 1-8): NVMeTCP Offload ULP
  The nvme-tcp-offload patches, will be sent to
  'linux-nvme@lists.infradead.org'.

- Part 2 (RFC patches 9-15): QED NVMeTCP Offload
  The qed infrastructure, will be sent to 'netdev@vger.kernel.org'.

Once part 1 and 2 are accepted:

- Part 3 (RFC patches 16-27): QEDN NVMeTCP Offload
  The qedn patches, will be sent to 'linux-nvme@lists.infradead.org'.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces APIs which the NVMeTCP Offload device (qedn)
will use through the paired net-device (qede).
It includes APIs for:
- ipv4/ipv6 routing
- get VLAN from net-device
- TCP ports reservation
Acked-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NNikolay Assa <nassa@marvell.com>
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NOmkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces the NVMeTCP FW initializations which is used
to initialize the IO level configuration into a per IO HW
resource ("task") as part of the IO path flow.

This includes:
- Write IO FW initialization
- Read IO FW initialization.
- IC-Req and IC-Resp FW exchange.
- FW Cleanup flow (Flush IO).
Acked-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NOmkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces the NVMeTCP Offload FW and HW  HSI in order
to initialize the IO level configuration into a per IO HW
resource ("task") as part of the IO path flow.
Acked-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NOmkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces the functionality of HW filter block.
It adds and removes filters based on source and target TCP port.

It also add functionality to clear all filters at once.
Acked-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NOmkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces the NVMeTCP HSI and HSI functionality in order to
initialize and interact with the HW device as part of the connection level
HSI.

This includes:
- Connection offload: offload a TCP connection to the FW.
- Connection update: update the ICReq-ICResp params
- Connection clear SQ: outstanding IOs FW flush.
- Connection termination: terminate the TCP connection and flush the FW.
Acked-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NOmkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces the NVMeTCP device and PF level HSI and HSI
functionality in order to initialize and interact with the HW device.
The patch also adds qed NVMeTCP personality.

This patch is based on the qede, qedr, qedi, qedf drivers HSI.
Acked-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDean Balandin <dbalandin@marvell.com>
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NOmkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add TCP_ULP as a storage common TCP offload FW resource layout.
This will be used by the core driver (QED) for both the NVMeTCP and iSCSI.
Acked-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NPrabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: NOmkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NShai Malin <smalin@marvell.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In two places the 'ep_desc' and 'skb' local variables are used only
within if() or for() block, so they scope can be reduced which makes the
entire code slightly easier to follow.  No functional change.
Suggested-by: NJoe Perches <joe@perches.com>
Signed-off-by: NKrzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "continue" statement at the end of a for loop does not have an
effect.  Entire loop contents can be slightly simplified to increase
code readability.  No functional change.
Suggested-by: NJoe Perches <joe@perches.com>
Signed-off-by: NKrzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Karsten Graul says:

====================
net/smc: updates 2021-06-02

Please apply the following patch series for smc to netdev's net-next tree.

Both patches are cleanups and remove unnecessary code.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

destroy_workqueue() already calls drain_workqueue(), which is a stronger
variant of flush_workqueue().
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>