We have a confusion of two different abstractions in the Common
Code:  Physical Link (Port) and Logical Network Interface (Virtual
Interface), and we haven't been properly managing the state of the
intersection of those two abstractions.
On the one hand we have the Physical state of the Link -- up or down --
and on the other we have the logical state of the VI, enabled or not.
{ethN} refers to both the Physical and Logical State. In this case,
ifconfig only affects/interrogates the Logical State of a VI,
and ethtool only deals with the Physical State. And these are different.

So, just because we disable the VI, we don't really want to change the
Physical Link Up/Down state.  Thus, the previous hack to set
"lc->link_ok = 0" when we disable a VI is completely incorrect.

Where we get into trouble is where the Physical Link State and the
Logical VI State cross swords.  And that happens in
t4_handle_get_port_info() where we need to manage/safe the Physical
Link State, but we also need to know when the Logical VI State has
changed and pass that back up to the OS-dependent Driver routine
t4_os_link_changed() which is concerned about the Logical Interface.

So we enable a VI and that causes Firmware to send us a new Port
Information message, but if none of the Physical Link State
particulars have changed, we don't call t4_os_link_changed().

This fix uses the existing OS Contract APIs for the Common Code to
inform the OS-dependent portion of the Host Driver when the "Link" (really
Logical Network Interface) is "up" or "down". A new API
t4_enable_pi_params() is added which calls t4_enable_vi_params() and,
if that is successful, then calls back to the OS Contract API
t4_os_link_changed() notifying the OS-dependent layer of the
potential Link State change.

Original Work by : Casey Leedom <leedom@chelsio.com>
Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

clean up init_one and use chip_ver consistently throughout
init_one() for chip version.
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

t4_prep_fw doesn't check for card_fw pointer before store the read data,
which could lead to a NULL pointer dereference if kvzalloc failed.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

trigger an L1 configure operation when a transceiver module
is inserted in order to cause current "sticky" options like
Requested Forward Error Correction to be reapplied.
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We no longer require a check for cxgb4 to be MASTER
when configuring SRIOV, It was required when we had
module parameter to instantiate vf.
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register callback to collect hardware/firmware dumps in second kernel
before hardware/firmware is initialized. The dumps for each device
will be available as elf notes in /proc/vmcore in second kernel.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

do not sleep while adding or deleting udp tunnel.

Fixes: 846eac3f ("cxgb4: implement udp tunnel callbacks")
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

set cntrl bits to indicate whether inner header checksum
needs to be calculated whenever the packet is an encapsulated
packet and enable supported encap features.

Fixes: d0a1299c ("cxgb4: add support for vxlan segmentation offload")
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

adapter->rawf_cnt was not initialized, thereby
ndo_udp_tunnel_{add/del} was returning immediately
without initializing {vxlan/geneve}_port.
Also initializes mps_encap_entry refcnt.

Fixes: 846eac3f ("cxgb4: implement udp tunnel callbacks")
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix the wrong conversion where 1 Mbps was converted to
1024 Kbps.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

copy mbox size to adapter instances of PF0-3 to avoid
mbox log overflow. This fixes the possible protection
fault.

Fixes: baf50868 ("cxgb4: restructure VF mgmt code")
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

firmware expects HMA memory to be zeroed, use __GFP_ZERO
for HMA memory allocation.

Fixes: 8b4e6b3c ("cxgb4: Add HMA support")
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Read the Inline TLS capability from firmware.
Determine the area reserved for storing the keys
Dump the Inline TLS tx and rx records count.
Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Reviewed-by: NMichael Werner <werner@chelsio.com>
Reviewed-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return a negative error code from the hash filter init error
handling case instead of 0, as done elsewhere in this function.

Fixes: 5c31254e ("cxgb4: initialize hash-filter configuration")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Copy vlan_id to get it displayed in vf info.
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudhar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When NetworkManager is enabled, there are chances that interface up
is called even before probe completes. This means we have not yet
allocated the FW sge queues, hence rest of ingress queue allocation
wont be proper. Fix this by calling setup_fw_sge_queues() before
register_netdev().

Fixes: 0fbc81b3 ('chcr/cxgb4i/cxgbit/RDMA/cxgb4: Allocate resources dynamically for all cxgb4 ULD's')
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If FW supports RDMA WRITE_COMPLETION functionality, then advertise that
to the ULDs. This will be used by iw_cxgb4 to allow WRITE_COMPLETION
work requests.
Signed-off-by: NPotnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: NRaju Rangoju <rajur@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If FW supports RDMA WRITE_WITH_IMMEDATE functionality, then advertise
that
to the ULDs. This will be used by iw_cxgb4 to allow WRITE_WITH_IMMEDIATE
work requests.
Signed-off-by: NPotnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: NRaju Rangoju <rajur@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support to query FW for the HW SRQ table start/end, and
advertise that for ULDs.
Signed-off-by: NRaju Rangoju <rajur@chelsio.com>
Reviewed-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

notify uld drivers if the adapter encounters fatal
error.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HMA(Host Memory Access) maps a part of host memory for T6-SO memfree cards.

This commit does the following:
- Query FW to check if we have HMA support. If yes, the params will
  return HMA size configured in FW. We will dma map memory based
  on this size.
- Also contains changes to get HMA memory information via debugfs.
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NMichael Werner <werner@chelsio.com>
Signed-off-by: NGanesh GR <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

50Gbps is a supported speed, Stop reporting it as
unsupported speed.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

T6 cards can support up to 100 G speeds. So, increase
max programmable tx rate limit to 100 Gbps.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not set 'needs_free_netdev' as we do call free_netdev
for mgmt net devices, doing both hits BUG_ON.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

instantiation of VF's on different adapters fails, copy
adapter index and chip type to PF0-3 adapter instances
to fix the issue.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

free pf 0-3 resources, commit baf50868 ("cxgb4:
restructure VF mgmt code") erroneously removed the
code which frees the pf 0-3 resources, causing the
probe of pf 0-3 to fail in case of driver reload.

Fixes: baf50868 ("cxgb4: restructure VF mgmt code")
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit baf50868 ("cxgb4: restructure VF mgmt code") has reordered
some code but an error handling label has not been updated accordingly.
So fix it and free 'adapter' if 't4_wait_dev_ready()' fails.

Fixes: baf50868 ("cxgb4: restructure VF mgmt code")
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

implement ndo_set_vf_vlan for mgmt netdevice to configure
the PCIe VF.

Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add geneve segmentation offload support of T6 cards.

Original work by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

restructure the code which adds support for configuring
PCIe VF via mgmt netdevice. which was added by
commit 7829451c ("cxgb4: Add control net_device for
configuring PCIe VF")

Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add changes to t4_eth_xmit to enable vxlan segmentation
offload support.

Original work by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ndo_udp_tunnel_add and ndo_udp_tunnel_del
to support vxlan tunnelling.

Original work by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use meminfo to identify the egress and ingress context regions and
fetch all valid contexts from those regions. Also flush all contexts
before attempting collection to prevent stale information.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added Tx routine for ULD
- define interface for ULD Tx.

Export routines used for Tx data
- Routines common for data transmit are used by cxgb4 and chcr
  drivers.
- EXPORT routines enable transmit from chcr driver.
Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This restores the original behaviour before the block callbacks were
introduced. Allow the drivers to do binding of block always, no matter
if the NETIF_F_HW_TC feature is on or off. Move the check to the block
callback which is called for rule insertion.
Reported-by: NAlexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

T6 supports ~500K hash filters and can theoretically climb up to
~1 million hash filters. Preallocated hash table is not efficient
in terms of memory usage. So, use rhashtable instead which gives
the flexibility to grow based on usage.
Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a combined ulptx work-request to send hash filter deletion
request to hw. Hash filter deletion reply is processed on
getting cpl_abort_rpl_rss.

Release any L2T/SMT/CLIP entries on filter deletion.
Also, free up the corresponding filter entry.
Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to create hash (exact-match) filters based on the value
of 'hash' field in ch_filter_specification.

Allocate SMT/L2T entries if DMAC-rewrite/SMAC-rewrite is requested.

Allocate CLIP entry in case of IPv6 filter.

Use cpl_act_open_req[6] to send hash filter create request to hw.
Also, the filter tuple is calculated as part of sending this request.

Hash-filter reply is processed on getting cpl_act_open_rpl.
In case of success, various bits/fields in filter-tcb are set per
filter requirement, such as enabling filter hitcnts, and/or various
header rewrite operations, such as VLAN-rewrite, NAT or
(L3/L4)-rewrite, and SMAC/DMAC-rewrite. In case of failure, clear the
filter entry and release any hw resources occupied by it.

The patch also moves the functions set_tcb_field, set_tcb_tflag and
configure_filter_smac towards beginning of file.
Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>