Enable ELP authorization in AP mode and enable the use
of the wakeup bit in the ELP register.

Introduce AP role sleep configuration which is disabled
by default. When configured, it allows the AP to sleep
when ELP is authorized for it.
Signed-off-by: NKobi Leibovitch <kobi.lev100@gmail.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Enabling beacon filtering before receving a beacon
might result in not having a beacon at all for the
current connected AP, which prevents the station
from entering power-save.

Replace the current approach (of starting beacon
filtering on init) and configure beacon filering
only after bss_conf->dtimper is set (which means
mac80211 already parsed a beacon).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

12xx chips allow only OFDM rates in AP mode for BT-Coex purposes. This
is no longer required in 18xx chips, starting with FW 8.6.0.0.8.

Update the min allowed FW version in 18xx to support this functionality.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add new ap_event_mask field, to indicate events that
should be unmasked only when there's an ap interface.

This is done in order to avoid spurious wakeups
when we don't care about the incoming event anyway.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

all the current firmwares support elp, so
we can safely remove WLCORE_QUIRK_NO_ELP.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In 18xx the calibration process of the PHY Cortex domain
requires to perform an active calibration of the channel
before it can be used for transmission. To fulfill world
wide regulatory restrictions, fw should be always
synchronized/updated with current CRDA configuration.
Add a new "CMD_DFS_CHANNEL_CONFIG" command to update the
fw with current reg-domain, this command passes a bit map
of channels that are allowed to be used for transmission.

The driver shall update the fw during initialization and
after each change in the current reg-domain
configuration. The driver will save the channel number of
incoming beacons during the scan process, as they might
be a result of the passive scan on
"IEEE80211_CHAN_PASSIVE_SCAN" channel and will update the
fw accordingly once the scan is finished, the purpose of
this is to be ready in case of the authentication request
on one of these disabled (uncalibrated) channels.

The new command requires to wait for the fw completion
event "DFS_CHANNELS_CONFIG_COMPLETE_EVENT".

No scan commands (including the sched scan) can be
executed concurrently with the "CMD_DFS_CHANNEL_CONFIG",
wl->mutex ensures that.

[Arik - move reset of reg_ch_conf_last to safe place inside
op_stop_locked]
[Eliad - adjust to new event waiting api]
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The scan APIs of 12xx and 18xx are totally different.
Use some common functions as much as possible (e.g.
for setting scan channels), but split scan.c into
chip-specific scan.c files, each implementing its
own scan mechanism.

(in other words - move most of the current wlcore's
scan.c into wl12xx, and implement a similar mechanism
in 18xx, according to the new api)

New wlcore ops are introduced in order to call the
chip-specific scan functions.

The template indices used for each scan (regular/scheduled)
are also different between the chips, so set the correct
indices used for each scan type after identifying the chip.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The supported_rates field should contain all our supported
rates, even if the remote peer doesn't support them.

(rename CONF_TX_AP_ENABLED_RATES to CONF_TX_ENABLED_RATES,
as we now use it for both ap and sta)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Currently, all the (station) roles use the same
keep-alive template id (0). However, the klv
template ids shouldn't be shared by different
roles.

Implement a simple klv_templates bitmap, and let
each role allocate its own klv template id on
role initialization.

[Arik - remove invalidation of KLV template when getting into "idle".
This is already handled in unjoin]
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>

The driver configures the firmware template for probe requests during
the scan process.  If the same template is used for one-shot and sched
scans they will override each other when running scans simultaneously.

This fix works only on firmwares later than X.3.9.2.112 for single
role and X.3.9.2.23 for multi-role.

[Some cleaning-up and renaming of the quirk to something smaller --
Luca.]
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The sleep_auth value of the last interface to be set up prevailed when
an interface was removed. Take care of this by correctly configuring the
value according to the remaining STA/AP interfaces.

Take this opportunity to refactor the sleep_auth setting code for better
readability.

[Small style fix. -- Luca]
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Hold a value for sta_sleep_auth that is amenable to change by debugfs.
When detecting a legal value in this variable on interface init, use it
as an override value for sleep_auth.

This makes debugging more intuitive using the debugfs value.

Increment the conf version since we added an element to the conf
structure.

Note: An AP going up will always set sleep_auth to PSM_CAM.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add a HW op to add extra enabled rates for AP-mode data-rates. Since
the rates might depend on channel properties, reconfigure AP-mode rates
when these change.

Implement the HW op for the 18xx family, where MIMO or wide-chan rates
can be added.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add an op for family-specific vif initialization.  Currently unused,
but will be needed when wl18xx support is implemented.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Move all the wl12xx-specific hw initialization procedures into a new
hw_init op.  Move some commands and ACX functions to wl12xx.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Inverting the quirk flag to indicate Tx-alignment. This aligns it with
the similar Rx-side quirk.

The call to wl1271_set_block_size() decides whether SDIO block size
alignment can be used or not.  In case we're using SPI, we can't use
the block size alignment, so the function returns false.  So we set
the quirk when wl1271_set_block_size() returns true and let the wl12xx
lower driver unset the bit for wl127x (since it doesn't support this
quirk).
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

ELP is a very complicated process in the firmware.  Due to its
complexity, in some early firmware revisions, the ELP feature is
disabled.  To support this cases, this patch adds a quirk that
disables ELP mode.

When ELP is not supported, do not attempt to enter ELP when requested by
the driver.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Move the code that identifies the chip ID and selects the appropriate
firmware to an operation implemented by the lower driver.  Also move
the quirks definitions into wlcore.h and rename to WLCORE_QUIRK_*.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add register tables support in wlcore, add some new IO functions to
read and write to chip-specific register and data addresses.  Move
some common register values from wl12xx to wlcore and add the
registers table to wl12xx.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Rename the wl12xx driver directory to wlcore as an initial step
towards the split of the driver into wlcore and wl12xx.  We just
rename the directory first to keep git blame happy.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Move wl12xx and wl1251 modules into a new drivers/net/wireless/ti
directory.  Add a TI WLAN Kconfig option and Makefile to support this
change.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Cc: John W. Linville <linville@tuxdriver.com>

Increase max scan IEs to allow big probe-req frames

Report a correct max-length for the scan IEs we can support, according
to the now larger size of the probe-req template.
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

When configuring the arp response template,
and encryption is enabled, we should add some
space and set the protected flag bit in the fc.

In order to track the encryption type, set
wlvif->encryption_type when setting an encryption key,
and reconfigure the arp response. Clear this field on
wl1271_join, as keys have to be re-configured
anyway after a join command.

Similarly, track whether QoS is configured.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The set_template commands now takes the role_id as
parameter.

Usually, we'll use the vif's main role_id.
However, sometimes we'll want to use
wlvif->dev_role_id instead of wlvif->role_id,
so pass the wanted role_id as param.

Update WL127X_FW_NAME/WL128X_FW_NAME.

(This commit starts a series of fw update patches,
and changes the start() callback to return an error
in order to prevent the use of the driver during the
transition. This change will be reverted in the
last patch of series)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The ACX_PD_THRESHOLD configuration command is deprecated and should
not be used anymore.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We need to set the extended radio parameters for wl127x only.
Currently, we were only calling this command with wl127x STA mode, but
we should also do it for AP mode.

Move the call to the extended radio paramaters to the common hw_init
and use a single if for the chip type to do everything at once.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The keep alive template should have a max size of
sizeof(struct ieee80211_qos_hdr).

Additionally, Remove the redundant wl12xx_qos_null_data_template
struct.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

SDIO blocksize alignment support is now the rule, not the exception.
To simplify the code in patches to come, invert the meaning of the
quirk to be negative (ie. the quirk is set if the device does _not_
support blocksize alignment).
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Enable beacon filtering on STA init, and don't disable it when entering
active mode. Otherwise dynamic-PS supports means we receive beacons from
the current AP during any Tx/Rx performed by the driver.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Separate the debugging macros and other definitions to a new debug.h
file.  This is be needed because the sdio and spi modules don't need
to depend on the wl12xx module anymore, but still need to include
wl12xx.h.  Currently they do depend on it, because of the debugging
global that wl12xx exports.  A future patch will remove this
dependency.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

allocate the rate policies dynamically, instead of using hardcoded
indexes. this is needed for proper multi-role configuration.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

move power_level into the per-interface data.

mac80211 configures some values (e.g. band, channel)
globally, while we configure them per-interface.

In order to make it easier to keep track of the
configured value for each value while keeping sync
with mac80211, save these values both globally
and per-vif.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

If there is an active AP role, stay always on.
Otherwise, allow chip to enter elp.

(Note that this is a global configuration, so if the
device is already configured according to our policy,
we don't have to configure it again)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

move ba_fields into the per-interface data, rather than
being global.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

move role_id into the per-interface data, rather than
being global.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

move bss_type into the per-interface data, rather than
being global.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

move basic_rate into the per-interface data, rather than
being global.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

move rate_set into the per-interface data, rather than
being global.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Define a per-vif data struct.
This struct holds all the vif-specifc data, which is
currently being hold by the global wl struct.

Start by moving the basic_rate_set field into it.

NOTE: in order to make the patches a bit smaller, start by
using wl->vif in some functions, instead of changing all
the function prototypes at once. finally, wl->vif will be
removed altogether.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Split the init sequence into common commands (non role-specific)
and role-specific commands.

We still need to call the common commands only on add_interface()
(rather than on start()) as the fw must get the mac address
when uploading the nvs.

Future patches will refactor the init sequence further more.
Signed-off-by: NEliad Peller <eliad@wizery.com>
[fixed a couple of sparse warnings]
Signed-off-by: NLuciano Coelho <coelho@ti.com>