The last patches moved a lot of code from ironlake_crtc_mode_set to
sub-functions, so these variables became useless. You could get
warnings by enabling -Wunused-but-set-variable.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Too many lines just to compute the value of a single variable, so
move this to its own function.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The set_m_n code was spread all over the mode_set function.

Version 2:
Don't set the DP M/N registers on ironlake_set_m_n. Daniel Vetter has
plans to add some encoder-specific callbacks. Also, on this version we
don't change the order we're writing the registers, making the code
change safer.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As noticed by Daniel Vetter, intel_pipe_choose_bpp_dither should
already check for invalid bpp values and set a valid value, so remove
the recheck inside ironlake_crtc_mode_set and also replace a "default"
switch case inside ironlake_set_pipeconf with a BUG().
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This should never happen, but the silent "return" makes me wonder
every time I try to debug InfoFrame bugs, so promote this to BUG() to
make sure people will complain if we ever break this.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Fix potential NULL pointer dereference in edac_unregister_sysfs() on
system boot introduced in 3.6-rc1.

Since commit 7a623c03 ("edac: rewrite the sysfs code to use struct
device") edac_mc_alloc() no longer initializes embedded kobjects in
struct mem_ctl_info.  Therefore edac_mc_free() can no longer simply
decrement a kobject reference count to free the allocated memory unless
the memory controller driver module had also called edac_mc_add_mc().

Now edac_mc_free() will check if the newly embedded struct device has
been registered with sysfs before using either the standard device
release functions or freeing the data structures itself with logic
pulled out of the error path of edac_mc_alloc().

The BUG this patch resolves for me:

  BUG: unable to handle kernel NULL pointer dereference at   (null)
  EIP is at __wake_up_common+0x1a/0x6a
  Process modprobe (pid: 933, ti=f3dc6000 task=f3db9520 task.ti=f3dc6000)
  Call Trace:
    complete_all+0x3f/0x50
    device_pm_remove+0x23/0xa2
    device_del+0x34/0x142
    edac_unregister_sysfs+0x3b/0x5c [edac_core]
    edac_mc_free+0x29/0x2f [edac_core]
    e7xxx_probe1+0x268/0x311 [e7xxx_edac]
    e7xxx_init_one+0x56/0x61 [e7xxx_edac]
    local_pci_probe+0x13/0x15
  ...

Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NShaun Ruffell <sruffell@digium.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

coccinelle warns about:

+ drivers/edac/edac_mc.c:429:9-23: ERROR: reference preceded by free on line 429

   421         if (mci->csrows) {
 > 422                 for (chn = 0; chn < tot_channels; chn++) {
   423                         csr = mci->csrows[chn];
   424                         if (csr) {
 > 425                                 for (chn = 0; chn < tot_channels; chn++)
   426                                          kfree(csr->channels[chn]);
   427                                  kfree(csr);
   428                          }
 > 429                          kfree(mci->csrows[i]);
   430                  }
   431                  kfree(mci->csrows);
   432          }

and that code block seem to mess things up in several ways (double free, memory
leak, out-of-bound reads etc.):

L422: The iterator "chn" and bound "tot_channels" are totally wrong. Should be
      "row" and "tot_csrows" respectively. Which means either memory leak, or
      out-of-bound reads (which if does not trigger an immediate page fault
      error, will further lead to kfree() on random addresses).

L425: The inner loop is reusing the same iterator "chn" as the outer loop,
      which could lead to premature end of the outer loop, and hence memory leak.

L429: The array index 'i' in mci->csrows[i] is a temporary value used in
      previous loops, and won't change at all in the current loop. Which
      means either out-of-bound read and possibly kfree(random number), or the
      same mci->csrows[i] get freed once and again, and possibly double free
      for the kfree(csr) in L427.

L426/L427: a kfree(csr->channels) is needed in between to avoid leaking the memory.

The buggy code was introduced by commit de3910eb ("edac: change the mem
allocation scheme to make Documentation/kobject.txt happy") in the 3.6-rc1
merge window. Fix it by freeing up resources in this order:

  free csrows[i]->channels[j]
  free csrows[i]->channels
  free csrows[i]
  free csrows

CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The quirk introduced with commit
00250ec9 (hwmon: fam15h_power: fix
bogus values with current BIOSes) is not only required during driver
load but also when system resumes from suspend. The BIOS might set the
previously recommended (but unsuitable) initilization value for the
running average range register during resume.
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Tested-by: NAndreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org # 3.0+

coretemp_init loops with for_each_online_cpu, adding platform_devices
and sysfs interfaces, then calls register_hotcpu_notifier.  There is a
race if a CPU is offlined or onlined after the loop, but before
register_hotcpu_notifier.  The race might result in the absence of a
platform_device+sysfs interface for an online CPU, or the presence of
a platform_device+sysfs interface for an offline CPU.  A similar race
occurs during coretemp_exit, after the module calls
unregister_hotcpu_notifier, but before it unregisters all devices, a
CPU might offline and a device for an offline CPU will exist for a
short while.

This fix surrounds for_each_online_cpu and register_hotcpu_notifier
with get_online_cpus+put_online_cpus; and surrounds
unregister_hotcpu_notifier and device unregistering with
get_online_cpus+put_online_cpus.

Build tested.
Signed-off-by: NSilas Boyd-Wickizer <sbw@mit.edu>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

via_cputemp_init loops with for_each_online_cpu, adding
platform_devices, then calls register_hotcpu_notifier.  If a CPU is
offlined between the loop and register_hotcpu_notifier, then later
onlined, via_cputemp_device_add will attempt to add platform devices
with the same ID.  A similar race occurs during via_cputemp_exit,
after the module calls unregister_hotcpu_notifier, a CPU might offline
and a device will exist for a CPU that is offline.

This fix surrounds for_each_online_cpu and register_hotcpu_notifier
with get_online_cpus+put_online_cpus; and surrounds
unregister_hotcpu_notifier and device unregistering with
get_online_cpus+put_online_cpus.

Build tested.
Signed-off-by: NSilas Boyd-Wickizer <sbw@mit.edu>
Acked-by: NHarald Welte <laforge@gnumonks.org>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This patch fixes an issue introduced after commit 4ea54542
("HID: Fix race condition between driver core and ll-driver").

After that commit, hid-core discards any incoming packet that arrives while
hid driver's probe function is being executed.

This broke the enumeration process of hid-logitech-dj, that must receive
control packets in-band with the mouse and keyboard packets. Discarding mouse
or keyboard data at the very begining is usually fine, but it is not the case
for control packets.

This patch forces a re-enumeration of the paired devices when a packet arrives
that comes from an unknown device.

Based on a patch originally written by Benjamin Tissoires.

Cc: stable@vger.kernel.org   # v3.2+
Signed-off-by: NNestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

We need to kfree names for led_mute and led_micmute in tpkbd_remove_tp().
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NBernhard Seibold <mail@bernhard-seibold.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch fixes an issue introduced by commit ID 6a81c26f
[net/stmmac: remove conditional compilation of clk code], which
switched from the internal stmmac_clk_{en}{dis}able calls to
clk_{en}{dis}able. By this, calling clk_prepare and clk_unprepare
was removed.

clk_{un}prepare is mandatory for platforms using common clock framework.
Since these drivers are used by SPEAr platform, which supports common
clock framework, add clk_{un}prepare() support for them. Otherwise
the clocks are not correctly en-/disabled and ethernet support doesn't
work.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of error, the function clk_get() returns ERR_PTR()
and never returns NULL pointer. The NULL test in the error
handling should be replaced with IS_ERR().

dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of error, the function clk_get() returns ERR_PTR()
and never returns NULL pointer. The NULL test in the error
handling should be replaced with IS_ERR().

dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a build failure introduced in commit 66636287
("gianfar: Support the get_ts_info ethtool method."). Not only was a
global variable inconsistently named, but also it was not exported as
it should have been.

This fix is also needed in stable version 3.5.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since version 7.4 the FW configures in the pci config space the max
number of interrupts available to the physical function, instead of
the exact number to use.
This causes a false warning in driver when comparing the number of
configured interrupts to the number about to be used.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes an oops which occurs when unloading the driver, while the
network interface is still up. The problem is that first the io mapping is
teared own, then the CAN device is unregistered, resulting in accessing the
hardware's iomem:

[  172.744232] Unable to handle kernel paging request at virtual address c88b0040
[  172.752441] pgd = c7be4000
[  172.755645] [c88b0040] *pgd=87821811, *pte=00000000, *ppte=00000000
[  172.762207] Internal error: Oops: 807 [#1] PREEMPT ARM
[  172.767517] Modules linked in: ti_hecc(-) can_dev
[  172.772430] CPU: 0    Not tainted  (3.5.0alpha-00037-g3554cc0 #126)
[  172.778961] PC is at ti_hecc_close+0xb0/0x100 [ti_hecc]
[  172.784423] LR is at __dev_close_many+0x90/0xc0
[  172.789123] pc : [<bf00c768>]    lr : [<c033be58>]    psr: 60000013
[  172.789123] sp : c5c1de68  ip : 00040081  fp : 00000000
[  172.801025] r10: 00000001  r9 : c5c1c000  r8 : 00100100
[  172.806457] r7 : c5d0a48c  r6 : c5d0a400  r5 : 00000000  r4 : c5d0a000
[  172.813232] r3 : c88b0000  r2 : 00000001  r1 : c5d0a000  r0 : c5d0a000
[  172.820037] Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
[  172.827423] Control: 10c5387d  Table: 87be4019  DAC: 00000015
[  172.833404] Process rmmod (pid: 600, stack limit = 0xc5c1c2f0)
[  172.839447] Stack: (0xc5c1de68 to 0xc5c1e000)
[  172.843994] de60:                   bf00c6b8 c5c1dec8 c5d0a000 c5d0a000 00200200 c033be58
[  172.852478] de80: c5c1de44 c5c1dec8 c5c1dec8 c033bf2c c5c1de90 c5c1de90 c5d0a084 c5c1de44
[  172.860992] dea0: c5c1dec8 c033c098 c061d3dc c5d0a000 00000000 c05edf28 c05edb34 c000d724
[  172.869476] dec0: 00000000 c033c2f8 c5d0a084 c5d0a084 00000000 c033c370 00000000 c5d0a000
[  172.877990] dee0: c05edb00 c033c3b8 c5d0a000 bf00d3ac c05edb00 bf00d7c8 bf00d7c8 c02842dc
[  172.886474] df00: c02842c8 c0282f90 c5c1c000 c05edb00 bf00d7c8 c0283668 bf00d7c8 00000000
[  172.894989] df20: c0611f98 befe2f80 c000d724 c0282d10 bf00d804 00000000 00000013 c0068a8c
[  172.903472] df40: c5c538e8 685f6974 00636365 c61571a8 c5cb9980 c61571a8 c6158a20 c00c9bc4
[  172.911987] df60: 00000000 00000000 c5cb9980 00000000 c5cb9980 00000000 c7823680 00000006
[  172.920471] df80: bf00d804 00000880 c5c1df8c 00000000 000d4267 befe2f80 00000001 b6d90068
[  172.928985] dfa0: 00000081 c000d5a0 befe2f80 00000001 befe2f80 00000880 b6d90008 00000008
[  172.937469] dfc0: befe2f80 00000001 b6d90068 00000081 00000001 00000000 befe2eac 00000000
[  172.945983] dfe0: 00000000 befe2b18 00023ba4 b6e6addc 60000010 befe2f80 a8e00190 86d2d344
[  172.954498] [<bf00c768>] (ti_hecc_close+0xb0/0x100 [ti_hecc]) from [<c033be58>] (__dev__registered_many+0xc0/0x2a0)
[  172.984161] [<c033c098>] (rollback_registered_many+0xc0/0x2a0) from [<c033c2f8>] (rollback_registered+0x20/0x30)
[  172.994750] [<c033c2f8>] (rollback_registered+0x20/0x30) from [<c033c370>] (unregister_netdevice_queue+0x68/0x98)
[  173.005401] [<c033c370>] (unregister_netdevice_queue+0x68/0x98) from [<c033c3b8>] (unregister_netdev+0x18/0x20)
[  173.015899] [<c033c3b8>] (unregister_netdev+0x18/0x20) from [<bf00d3ac>] (ti_hecc_remove+0x60/0x80 [ti_hecc])
[  173.026245] [<bf00d3ac>] (ti_hecc_remove+0x60/0x80 [ti_hecc]) from [<c02842dc>] (platform_drv_remove+0x14/0x18)
[  173.036712] [<c02842dc>] (platform_drv_remove+0x14/0x18) from [<c0282f90>] (__device_release_driver+0x7c/0xbc)

Cc: stable <stable@vger.kernel.org>
Cc: Anant Gole <anantgole@ti.com>
Tested-by: NJan Luebbe <jlu@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The Revision 1.0 Janz CMOD-IO Carrier Board does not have support for
the reset registers. To support older hardware, the code is changed to
use the hardware reset register on the Janz VMOD-ICAN3 hardware itself.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This fixes the gpio reset problem so the Retina MBP works, but avoids
breaking the Dell systems. Ben will work on a better solution for 3.7.

Tested by me on retina MBP.
Signed-off-by: NDave Airlie <airlied@redhat.com>

In order for the network layer to see that AoE requires
no checksumming in a generic way, the packets must be
marked as requiring no checksum, so we make this requirement
explicit with the assertion.
Signed-off-by: NEd Cashin <ecashin@coraid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

we are currently returning ENODEV, as the clk_get may give a exact
error code in its returned pointer, assign it to the ret by using the
PTR_ERR function, so that the subsequent goto label will jump to the
error path and clean the driver and return the error correctly.
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the modes of Huawei E367 has this QMI/wwan interface:

 I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=07 Driver=(none)
 E:  Ad=83(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
 E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
 E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms

Huawei use subclass and protocol to identify vendor specific
functions, so adding a new vendor rule for this combination.

The Pantech devices UML290 (106c:3718) and P4200 (106c:3721) use
the same subclass to identify the QMI/wwan function.  Replace the
existing device specific UML290 entries with generic vendor matching,
adding support for the Pantech P4200.

The ZTE MF683 has 6 vendor specific interfaces, all using
ff/ff/ff for cls/sub/prot.  Adding a match on interface #5 which
is a QMI/wwan interface.

Cc: Fangxiaozhi (Franko) <fangxiaozhi@huawei.com>
Cc: Thomas Schäfer <tschaefer@t-online.de>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Shawn J. Goff <shawn7400@gmail.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cards typically have 5-7 scratch registers; one of these is reserved for
rdev->rptr_save_reg. Unfortunately the reservation is done in function
r100_cp_init, which is called by all drivers except r600 - and this
function is also invoked on resume from suspend. After several resumes,
no scratch registers are free and graphics acceleration is disabled.

Dmesg then reports either:
   *ERROR* radeon: cp failed to get scratch reg (-22).
   *ERROR* radeon: cp isn't working(-22).
   radeon 0000:01:00.0: failed initializing CP (-22).
or:
   *ERROR* radeon: failed to get scratch reg (-22).
   *ERROR* radeon: failed testing IB on GFX ring (-22).
   *ERROR* ib ring test failed (-22).

The chain of calls on boot for all except r600 is:
radeon_init -> ... -> (rXXX_init) -> rXXX_startup -> r100_cp_init

The chain of calls on resume for all except r600 is:
rXXX_resume -> rXXX_startup -> r100_cp_init.

R600 correctly allocates rptr_save_reg in r600_init (ie once only, not
in resume). However moving the code into the init functions for all
drivers means touching 4 drivers. So instead, this patch just adds a
test in r100_cp_init to avoid reallocating on resume. As the rdev
structure is allocated via kzalloc in radeon_driver_load_kms, and zero
is not a valid registerid, zero safely implies not-yet-allocated.

This issue appears to have been introduced in c7eff978 (3.6.0-rcN)
Signed-off-by: NSimon Kitching <skitching@vonos.net>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Somehow this hunk got dropped from my last patch. We do not have the
rc6_attrs when there is no CONFIG_PM so this causes a compilation error.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As we make the simplification of using a power-of-two size for the
execbuffer handle-to-object TLB, we should validate that this is actually
true and so clarify that premise.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Clear Audio Enable bit to trigger unsolicated event to notify Audio
Driver part the HDMI hot plug change. The patch fixed the bug when
remove HDMI cable the bit was not cleared correctly.

In intel_enable_hdmi(), if intel_hdmi->has_audio been true, the "Audio enable bit" will
be set to trigger unsolicated event to notify Alsa driver the change.

intel_hdmi->has_audio will be reset to false from intel_hdmi_detect() after
remove the hdmi cable, here's debug log:

[  187.494153] [drm:output_poll_execute], [CONNECTOR:17:HDMI-A-1] status updated from 1 to 2
[  187.525349] [drm:intel_hdmi_detect], HDMI: has_audio = 0

so when comes back to intel_disable_hdmi(), the "Audio enable bit" will not be cleared. And this
cause the eld infomation and pin presence doesnot update accordingly in alsa driver side.

This patch will also trigger unsolicated event to alsa driver to notify the hot plug event:

[  187.853159] ALSA sound/pci/hda/patch_hdmi.c:772 HDMI hot plug event: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=1
[  187.853268] ALSA sound/pci/hda/patch_hdmi.c:990 HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
Signed-off-by: NWang Xingchao <xingchao.wang@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

By providing a callback for when we need to bind the pages, and then
release them again later, we can shorten the amount of time we hold the
foreign pages mapped and pinned, and importantly the dmabuf objects then
behave as any other normal object with respect to the shrinker and
memory management.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Hopefully this makes userspace slightly less confused about us
frobbing the dpms state behind its back. Yeah, it would be better
to be more careful with not changing the dpms state, but that is
quite more invasive.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... because our current set_mode implementation doesn't bother to adjust
for the dpms state, we just forcefully update it. So stop pretending that
we're better than we are and rip out this extranous call.

Note that this totally confuses userspace, because the exposed connector
property isn't actually updated ...
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because they should have been disabled when shutting down the display
pipe previously. To ensure that this is the case, add a few assserts
instead of unconditionally disabling the fdi link.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Even with the old crtc helper code we should have disabled all
encoders on that pipe by now, and with the new code this would
definitely paper over a bug. We already have the necessary checks
in place in intel_disable_transcoder, so if we accidentally leave
a pch port on, this will be caught.

Hence just rip this all out.

Note that up to the patch in this giant modeset series that removes
the LVDS special case to avoid disabling LVDS in the encoder->prepare
callback ("drm/i915/lvds: ditch ->prepare special case"), this was not
the case for all outputs.

Also note that in

commit 1b3c7a47
Author: Zhenyu Wang <zhenyuw@linux.intel.com>
Date:   Wed Nov 25 13:09:38 2009 +0800

    drm/i915: Fix LVDS stability issue on Ironlake

this was already discovered independently and worked around. How I
bloody hate this entire mess of cludges piled on top of other cludges.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Rewriting the PTE entries using an WC mapping is roughly an order of
magnitude faster than through the uncached mapping. This makes an
observable difference on workloads that cycle through large numbers of
buffers, for example Chromium using ShmPixmaps where virtually all the
CPU time is currently spent rebinding the userptr.

v2: Limit the WC mapping to older generations as we have observed that
the TLB invalidation on SandyBridge+ is unreliable with WC updates.
See i-g-t/tests/gem_gtt_cpu_tlb
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In the future we may like to experiment with using a WC map of the GTT
portion. However, that will conflict with i915.ko mapping the entire bar
as UC in order to access the GPU registers. Instead we can shrink the
register ioremap to only map the register block.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by (IVB): Ben Widawsky <ben@bwidawsk.net>
Acked-by: NBen Widawsky <ben@bwidawsk.net>
[danvet: Squashed-in follow-up fix for gen2/3 registers file size from
Chris Wilson.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is useful for userspace utilities which wish to use the previous
interface, specifically for micromanaging the increase/decrease steps by
setting min == max.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Provide a standardized sysfs interface for setting min, and max
frequencies.  The code which reads the limits were lifted from the
debugfs files. As a brief explanation, the limits are similar to the CPU
p-states. We have 3 states:

RP0 - ie. max frequency
RP1 - ie. "preferred min" frequency
RPn - seriously lowest frequency

Initially Daniel asked me to clamp the writes to supported values, but
in conforming to the way the cpufreq drivers seem to work, instead
return -EINVAL (noticed by Jesse in discussion).
The values can be used by userspace wishing to control the limits of the
GPU (see the CC list for people who care).

v4: Make exceeding the soft limits return -EINVAL as well (Daniel)

v3: bug fix (Ben) -  was passing the MHz value to gen6_set_rps instead of
the step value. To fix, deal only with step values by doing the divide
at the top.

v2: add the dropped mutex_unlock in error cases (Chris)
EINVAL on both too min, or too max (Daniel)

v2 Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This has been tons of fun to figure out with git blame. The first
notion of this code block goes back to the original cpu edp enabling
for ilk in

commit 32f9d658
Author: Zhenyu Wang <zhenyuw@linux.intel.com>
Date:   Fri Jul 24 01:00:32 2009 +0800

    drm/i915: Add eDP support on IGDNG mobile chip

Two things are notable in this commit wrt to the this edp special
case:
- The IS_eDP check _only_ fires for DP A, i.e. cpu edp ports.
- The cpu edp port is disabled at the top of the dp_link_down function.

My theory is that these hacks was added to work around the completely
different modeset sequence for cpu edp ports compared to pch edp
ports. With the cpu edp confusion on ilk (and snb/ivb) now fixed up,
this shouldn't be required any more.

The really interesting question is how this special cases survived
this long in the code. The first step is declaring the pch port D as
eDP if it's used for an internal panel:

commit b329530c
Author: Adam Jackson <ajax@redhat.com>
Date:   Fri Jul 16 14:46:28 2010 -0400

    drm/i915/dp: Correctly report eDP in the core connector type

This commit unfortunately failed to notice that not all edp ports are
created equal. Then follow a flurry of refactorings, culminating in a
patch from Keith Packard which resulted in the current logic (by
making it "correct" for all platforms that have edp):

commit 417e822d
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Nov 1 19:54:11 2011 -0700

    drm/i915: Treat PCH eDP like DP in most places

None of these cleanups or refactorings supply any reason why we need
this code, they've simply carried it on as-is.

Hence presume it might be harmful with the current code and rip it
out. We do rewrite the link training bits completely anyway when
re-training the link.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The exec_list is of type drm_i915_gem_exec_object2 and so casting it to
a drm_i915_gem_relocation_entry is very confusing!
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is rather a hack to fix brightness hotkeys on a Clevo laptop. CADL is not
used anywhere in the driver code at the moment, but it could be used in BIOS as
is the case with the Clevo laptop.

The Clevo B7130 requires the CADL field to contain at least the ID of
the LCD device. If this field is empty, the ACPI methods that are called
on pressing brightness / display switching hotkeys will not trigger a
notification. As a result, it appears as no hotkey has been pressed.

Reference: https://bugs.freedesktop.org/show_bug.cgi?id=45452Tested-by: NPeter Wu <lekensteyn@gmail.com>
Signed-off-by: NPeter Wu <lekensteyn@gmail.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

See bspec, Vol3 Part2, Section 1.1.3 "Display Mode Set Sequence". This
applies to all platforms where we currently support eDP on, i.e. ilk,
snb & ivb.

Without this change we fail to light up the eDP port on previously
unused crtcs (likely because something is stuck on the old pipe), and
we also fail to properly disable the old pipe (i.e. bit 30 in the
PIPECONF register is stuck as set until the next reboot).

v2: Rebased on top of the edp panel off sequence changes in 3.6-rc2.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=44001Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>