We had some duplication of the internal OPAL functions.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Using size_t in our APIs is asking for trouble, especially
when some OPAL calls use size_t pointers.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Reviewed-by: NStewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

On PowerNV platform, we are holding an unnecessary refcount on a pci_dev, which
leads to the pci_dev is not destroyed when hotplugging a pci device.

This patch release the unnecessary refcount.
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

During the EEH hotplug event, iommu_add_device() will be invoked three times
and two of them will trigger warning or error.

The three times to invoke the iommu_add_device() are:

    pci_device_add
       ...
       set_iommu_table_base_and_group   <- 1st time, fail
    device_add
       ...
       tce_iommu_bus_notifier           <- 2nd time, succees
    pcibios_add_pci_devices
       ...
       pcibios_setup_bus_devices        <- 3rd time, re-attach

The first time fails, since the dev->kobj->sd is not initialized. The
dev->kobj->sd is initialized in device_add().
The third time's warning is triggered by the re-attach of the iommu_group.

After applying this patch, the error

    iommu_tce: 0003:05:00.0 has not been added, ret=-14

and the warning

    [  204.123609] ------------[ cut here ]------------
    [  204.123645] WARNING: at arch/powerpc/kernel/iommu.c:1125
    [  204.123680] Modules linked in: xt_CHECKSUM nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE ip6t_REJECT bnep bluetooth 6lowpan_iphc rfkill xt_conntrack ebtable_nat ebtable_broute bridge stp llc mlx4_ib ib_sa ib_mad ib_core ib_addr ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw bnx2x tg3 mlx4_core nfsd ptp mdio ses libcrc32c nfs_acl enclosure be2net pps_core shpchp lockd kvm uinput sunrpc binfmt_misc lpfc scsi_transport_fc ipr scsi_tgt
    [  204.124356] CPU: 18 PID: 650 Comm: eehd Not tainted 3.14.0-rc5yw+ #102
    [  204.124400] task: c0000027ed485670 ti: c0000027ed50c000 task.ti: c0000027ed50c000
    [  204.124453] NIP: c00000000003cf80 LR: c00000000006c648 CTR: c00000000006c5c0
    [  204.124506] REGS: c0000027ed50f440 TRAP: 0700   Not tainted  (3.14.0-rc5yw+)
    [  204.124558] MSR: 9000000000029032 <SF,HV,EE,ME,IR,DR,RI>  CR: 88008084  XER: 20000000
    [  204.124682] CFAR: c00000000006c644 SOFTE: 1
    GPR00: c00000000006c648 c0000027ed50f6c0 c000000001398380 c0000027ec260300
    GPR04: c0000027ea92c000 c00000000006ad00 c0000000016e41b0 0000000000000110
    GPR08: c0000000012cd4c0 0000000000000001 c0000027ec2602ff 0000000000000062
    GPR12: 0000000028008084 c00000000fdca200 c0000000000d1d90 c0000027ec281a80
    GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
    GPR20: 0000000000000000 0000000000000000 0000000000000000 0000000000000001
    GPR24: 000000005342697b 0000000000002906 c000001fe6ac9800 c000001fe6ac9800
    GPR28: 0000000000000000 c0000000016e3a80 c0000027ea92c090 c0000027ea92c000
    [  204.125353] NIP [c00000000003cf80] .iommu_add_device+0x30/0x1f0
    [  204.125399] LR [c00000000006c648] .pnv_pci_ioda_dma_dev_setup+0x88/0xb0
    [  204.125443] Call Trace:
    [  204.125464] [c0000027ed50f6c0] [c0000027ed50f750] 0xc0000027ed50f750 (unreliable)
    [  204.125526] [c0000027ed50f750] [c00000000006c648] .pnv_pci_ioda_dma_dev_setup+0x88/0xb0
    [  204.125588] [c0000027ed50f7d0] [c000000000069cc8] .pnv_pci_dma_dev_setup+0x78/0x340
    [  204.125650] [c0000027ed50f870] [c000000000044408] .pcibios_setup_device+0x88/0x2f0
    [  204.125712] [c0000027ed50f940] [c000000000046040] .pcibios_setup_bus_devices+0x60/0xd0
    [  204.125774] [c0000027ed50f9c0] [c000000000043acc] .pcibios_add_pci_devices+0xdc/0x1c0
    [  204.125837] [c0000027ed50fa50] [c00000000086f970] .eeh_reset_device+0x36c/0x4f0
    [  204.125939] [c0000027ed50fb20] [c00000000003a2d8] .eeh_handle_normal_event+0x448/0x480
    [  204.126068] [c0000027ed50fbc0] [c00000000003a35c] .eeh_handle_event+0x4c/0x340
    [  204.126192] [c0000027ed50fc80] [c00000000003a74c] .eeh_event_handler+0xfc/0x1b0
    [  204.126319] [c0000027ed50fd30] [c0000000000d1ea0] .kthread+0x110/0x130
    [  204.126430] [c0000027ed50fe30] [c00000000000a460] .ret_from_kernel_thread+0x5c/0x7c
    [  204.126556] Instruction dump:
    [  204.126610] 7c0802a6 fba1ffe8 fbc1fff0 fbe1fff8 f8010010 f821ff71 7c7e1b78 60000000
    [  204.126787] 60000000 e87e0298 3143ffff 7d2a1910 <0b090000> 2fa90000 40de00c8 ebfe0218
    [  204.126966] ---[ end trace 6e7aefd80add2973 ]---

are cleared.

This patch removes iommu_add_device() in pnv_pci_ioda_dma_dev_setup(), which
revert part of the change in commit d905c5df(PPC: POWERNV: move
iommu_add_device earlier).
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

With this patch I was able to update firmware on an LE kernel.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We have a subtle race when sending CPUs back to OPAL on kexec.

We mark them as "in real mode" right before we send them down. Once
we've booted the new kernel, it might try to call opal_reinit_cpus()
to change endianness, and that requires all CPUs to be spinning inside
OPAL.

However there is no synchronization here and we've observed cases
where the returning CPUs hadn't established their new state inside
OPAL before opal_reinit_cpus() is called, causing it to fail.

The proper fix is to actually wait for them to go down all the way
from the kexec'ing kernel.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The size of the sysparam sysfs files is determined from the device tree
at boot. However the buffer is hard coded to 64 bytes. If we encounter a
parameter that is larger than 64, or miss-parse the device tree, the
buffer will overflow when reading or writing to the parameter.

Check it at discovery time, and if the parameter is too large, do not
create a sysfs entry for it.
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The sysparam code currently uses the userspace supplied number of
bytes when memcpy()ing in to a local 64-byte buffer.

Limit the maximum number of bytes by the size of the buffer.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The OPAL calls are returning int64_t values, which the sysparam code
stores in an int, and the sysfs callback returns ssize_t. Make code a
easier to read by consistently using ssize_t.
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When a sysparam query in OPAL returned a negative value (error code),
sysfs would spew out a decent chunk of memory; almost 64K more than
expected. This was traced to a sign/unsigned mix up in the OPAL sysparam
sysfs code at sys_param_show.

The return value of sys_param_show is a ssize_t, calculated using

  return ret ? ret : attr->param_size;

Alan Modra explains:

  "attr->param_size" is an unsigned int, "ret" an int, so the overall
  expression has type unsigned int.  Result is that ret is cast to
  unsigned int before being cast to ssize_t.

Instead of using the ternary operator, set ret to the param_size if an
error is not detected. The same bug exists in the sysfs write callback;
this patch fixes it in the same way.

A note on debugging this next time: on my system gcc will warn about
this if compiled with -Wsign-compare, which is not enabled by -Wall,
only -Wextra.
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

commit 41dd03a9 may cause Oops in rtas_stop_self().

The reason is that the rtas_args was moved into stack space. For a box
with more that 4GB RAM, the stack could easily be outside 32bit range,
but RTAS is 32bit.

So the patch moves rtas_args away from stack by adding static before
it.
Signed-off-by: NLi Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: NAnton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit aac416fc (lkdtm: flush icache and report actions) calls
flush_icache_range from a module. It's exported on most architectures
that implement it, but not on powerpc. This patch exports it to fix
the module link failure.
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Pull slave-dmaengine fixes from Vinod Koul:
 "Back from long weekend here in India and now the time to send fixes
  for slave dmaengine.
   - Dan's fix of sirf xlate code
   - Jean's fix for timberland
   - edma fixes by Sekhar for SG handling and Yuan for changing init
     call"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dma: fix eDMA driver as a subsys_initcall
  dmaengine: sirf: off by one in of_dma_sirfsoc_xlate()
  platform: Fix timberdale dependencies
  dma: edma: fix incorrect SG list handling

Pull iommu fixes from Joerg Roedel:
 "Fixes for regressions:

   - fix wrong IOMMU enumeration causing some SCSI device drivers
     initialization failures
   - ARM-SMMU fixes for a panic condition and a wrong return value"

* tag 'iommu-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/arm-smmu: fix panic in arm_smmu_alloc_init_pte
  iommu/arm-smmu: Return 0 on unmap failure
  iommu/vt-d: fix bug in matching PCI devices with DRHD/RMRR descriptors
  iommu/vt-d: Fix get_domain_for_dev() handling of upstream PCIe bridges
  iommu/vt-d: fix memory leakage caused by commit ea8ea460

Pull perf tooling fixes from Ingo Molnar:
 "Three small tooling fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools: Improve error reporting
  perf tools: Adjust symbols in VDSO
  perf kvm: Fix 'Min time' counting in report command

Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/jolsa/perf into perf/urgent

Pull perf/urgent fixes from Jiri Olsa:

User visible changes:

  * Adjust symbols in VDSO to properly resolve its function names (Vladimir Nikulichev)

  * Improve error reporting for record session failure (Adrien BAK)

  * Fix 'Min time' counting in report command (Alexander Yarygin)
Signed-off-by: NJiri Olsa <jolsa@redhat.com>
Signed-off-by: NIngo Molnar <mingo@kernel.org>

In the current version, when using perf record, if something goes
wrong in tools/perf/builtin-record.c:375
  session = perf_session__new(file, false, NULL);

The error message:
"Not enough memory for reading per file header"

is issued. This error message seems to be outdated and is not very
helpful. This patch proposes to replace this error message by
"Perf session creation failed"

I believe this issue has been brought to lkml:
https://lkml.org/lkml/2014/2/24/458
although this patch only tackles a (small) part of the issue.

Additionnaly, this patch improves error reporting in
tools/perf/util/data.c open_file_write.

Currently, if the call to open fails, the user is unaware of it.
This patch logs the error, before returning the error code to
the caller.
Reported-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NAdrien BAK <adrien.bak@metascale.org>
Link: http://lkml.kernel.org/r/1397786443.3093.4.camel@beast
[ Reorganize the changelog into paragraphs ]
[ Added empty line after fd declaration in open_file_write ]
Signed-off-by: NJiri Olsa <jolsa@redhat.com>

pert-report doesn't resolve function names in VDSO:

$ perf report --stdio -g flat,0.0,15,callee --sort pid
...
            8.76%
               0x7fff6b1fe861
               __gettimeofday
               ACE_OS::gettimeofday()
...

In this case symbol values should be adjusted the same way as for executables,
relocatable objects and prelinked libraries.

After fix:

$ perf report --stdio -g flat,0.0,15,callee --sort pid
...
            8.76%
               __vdso_gettimeofday
               __gettimeofday
               ACE_OS::gettimeofday()
Signed-off-by: NVladimir Nikulichev <nvs@tbricks.com>
Tested-by: NNamhyung Kim <namhyung@kernel.org>
Reviewed-by: NAdrian Hunter <adrian.hunter@intel.com>
Link: http://lkml.kernel.org/r/969812.163009436-sendEmail@nvsSigned-off-by: NJiri Olsa <jolsa@redhat.com>

Every event in the perf-kvm has a 'stats' structure, which contains
max/min/average/etc times of handling this event.
The problem is that the 'perf-kvm stat report' command always shows
that 'min time' is 0us for every event. Example:

 # perf kvm stat report

 Analyze events for all VCPUs:

    VM-EXIT    Samples  Samples%     Time%   Min Time   Max Time Avg time
  [..]
  0xB2 MSCH         12     0.07%     0.00%        0us        8us 7.31us ( +-   2.11% )
  0xB2 CHSC         12     0.07%     0.00%        0us       18us 9.39us ( +-   9.49% )
  0xB2 STPX          8     0.05%     0.00%        0us        2us 1.88us ( +-   7.18% )
  0xB2 STSI          7     0.04%     0.00%        0us       44us 16.49us ( +-  38.20% )
  [..]

This happens because the 'stats' structure is not initialized and
stats->min equals to 0. Lets initialize the structure for every
event after its allocation using init_stats() function. This initializes
stats->min to -1 and makes 'Min time' statistics counting work:

 # perf kvm stat report

 Analyze events for all VCPUs:

    VM-EXIT    Samples  Samples%     Time%   Min Time   Max Time Avg time
  [..]
  0xB2 MSCH         12     0.07%     0.00%        6us        8us 7.31us ( +-   2.11% )
  0xB2 CHSC         12     0.07%     0.00%        7us       18us 9.39us ( +-   9.49% )
  0xB2 STPX          8     0.05%     0.00%        1us        2us 1.88us ( +-   7.18% )
  0xB2 STSI          7     0.04%     0.00%        1us       44us 16.49us ( +-  38.20% )
  [..]
Signed-off-by: NAlexander Yarygin <yarygin@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: NDavid Ahern <dsahern@gmail.com>
Link: http://lkml.kernel.org/r/1397053319-2130-3-git-send-email-borntraeger@de.ibm.com
[ Fixing the perf examples changelog output ]
Signed-off-by: NJiri Olsa <jolsa@redhat.com>

A va_list needs to be copied in case it needs to be used twice.

Thanks to Hugh for debugging this issue, leading to various panics.

Tested:

  lpq84:~# echo "|/foobar12345 %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h" >/proc/sys/kernel/core_pattern

'produce_core' is simply : main() { *(int *)0 = 1;}

  lpq84:~# ./produce_core
  Segmentation fault (core dumped)
  lpq84:~# dmesg | tail -1
  [  614.352947] Core dump to |/foobar12345 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 (null) pipe failed

Notice the last argument was replaced by a NULL (we were lucky enough to
not crash, but do not try this on your production machine !)

After fix :

  lpq83:~# echo "|/foobar12345 %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h" >/proc/sys/kernel/core_pattern
  lpq83:~# ./produce_core
  Segmentation fault
  lpq83:~# dmesg | tail -1
  [  740.800441] Core dump to |/foobar12345 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 pipe failed

Fixes: 5fe9d8ca ("coredump: cn_vprintf() has no reason to call vsnprintf() twice")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Diagnosed-by: NHugh Dickins <hughd@google.com>
Acked-by: NOleg Nesterov <oleg@redhat.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull x86 fix from Ingo Molnar:
 "This fixes the preemption-count imbalance crash reported by Owen
  Kibel"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mce: Fix CMCI preemption bugs

Pull scheduler fixes from Ingo Molnar:
 "Two fixes:

   - a SCHED_DEADLINE task selection fix
   - a sched/numa related lockdep splat fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Check for stop task appearance when balancing happens
  sched/numa: Fix task_numa_free() lockdep splat

Pull perf fixes from Ingo Molnar:
 "Two kernel side fixes:

   - an Intel uncore PMU driver potential crash fix
   - a kprobes/perf-call-graph interaction fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Use rdmsrl_safe() when initializing RAPL PMU
  kprobes/x86: Fix page-fault handling logic

Pull drm fixes from Dave Airlie:
 "Unfortunately this contains no easter eggs, its a bit larger than I'd
  like, but I included a patch that just moves code from one file to
  another and I'd like to avoid merge conflicts with that later, so it
  makes it seem worse than it is,

  Otherwise:
   - radeon: fixes to use new microcode to stabilise some cards, use
     some common displayport code, some runtime pm fixes, pll regression
     fixes
   - i915: fix for some context oopses, a warn in a used path, backlight
     fixes
   - nouveau: regression fix
   - omap: a bunch of fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (51 commits)
  drm: bochs: drop unused struct fields
  drm: bochs: add power management support
  drm: cirrus: add power management support
  drm: Split out drm_probe_helper.c from drm_crtc_helper.c
  drm/plane-helper: Don't fake-implement primary plane disabling
  drm/ast: fix value check in cbr_scan2
  drm/nouveau/bios: fix a bit shift error introduced by 457e77b2
  drm/radeon/ci: make sure mc ucode is loaded before checking the size
  drm/radeon/si: make sure mc ucode is loaded before checking the size
  drm/radeon: improve PLL params if we don't match exactly v2
  drm/radeon: memory leak on bo reservation failure. v2
  drm/radeon: fix VCE fence command
  drm/radeon: re-enable mclk dpm on R7 260X asics
  drm/radeon: add support for newer mc ucode on CI (v2)
  drm/radeon: add support for newer mc ucode on SI (v2)
  drm/radeon: apply more strict limits for PLL params v2
  drm/radeon: update CI DPM powertune settings
  drm/radeon: fix runpm handling on APUs (v4)
  drm/radeon: disable mclk dpm on R7 260X
  drm/tegra: Remove gratuitous pad field
  ...

Some i2c fixes over DisplayPort.

* 'drm-next-3.15-wip' of git://people.freedesktop.org/~deathsimple/linux:
  drm/radeon: Improve vramlimit module param documentation
  drm/radeon: fix audio pin counts for DCE6+ (v2)
  drm/radeon/dp: switch to the common i2c over aux code
  drm/dp/i2c: Update comments about common i2c over dp assumptions (v3)
  drm/dp/i2c: send bare addresses to properly reset i2c connections (v4)
  drm/radeon/dp: handle zero sized i2c over aux transactions (v2)
  drm/i915: support address only i2c-over-aux transactions
  drm/tegra: dp: Support address-only I2C-over-AUX transactions

Pull more networking fixes from David Miller:

 1) Fix mlx4_en_netpoll implementation, it needs to schedule a NAPI
    context, not synchronize it.  From Chris Mason.

 2) Ipv4 flow input interface should never be zero, it should be
    LOOPBACK_IFINDEX instead.  From Cong Wang and Julian Anastasov.

 3) Properly configure MAC to PHY connection in mvneta devices, from
    Thomas Petazzoni.

 4) sys_recv should use SYSCALL_DEFINE.  From Jan Glauber.

 5) Tunnel driver ioctls do not use the correct namespace, fix from
    Nicolas Dichtel.

 6) Fix memory leak on seccomp filter attach, from Kees Cook.

 7) Fix lockdep warning for nested vlans, from Ding Tianhong.

 8) Crashes can happen in SCTP due to how the auth_enable value is
    managed, fix from Vlad Yasevich.

 9) Wireless fixes from John W Linville and co.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
  net: sctp: cache auth_enable per endpoint
  tg3: update rx_jumbo_pending ring param only when jumbo frames are enabled
  vlan: Fix lockdep warning when vlan dev handle notification
  seccomp: fix memory leak on filter attach
  isdn: icn: buffer overflow in icn_command()
  ip6_tunnel: use the right netns in ioctl handler
  sit: use the right netns in ioctl handler
  ip_tunnel: use the right netns in ioctl handler
  net: use SYSCALL_DEFINEx for sys_recv
  net: mdio-gpio: Add support for separate MDI and MDO gpio pins
  net: mdio-gpio: Add support for active low gpio pins
  net: mdio-gpio: Use devm_ functions where possible
  ipv4, route: pass 0 instead of LOOPBACK_IFINDEX to fib_validate_source()
  ipv4, fib: pass LOOPBACK_IFINDEX instead of 0 to flowi4_iif
  mlx4_en: don't use napi_synchronize inside mlx4_en_netpoll
  net: mvneta: properly configure the MAC <-> PHY connection in all situations
  net: phy: add minimal support for QSGMII PHY
  sfc:On MCDI timeout, issue an FLR (and mark MCDI to fail-fast)
  mwifiex: fix hung task on command timeout
  mwifiex: process event before command response
  ...

Pull cifs fixes from Steve French:
 "A set of 5 small cifs fixes"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  cif: fix dead code
  cifs: fix error handling cifs_user_readv
  fs: cifs: remove unused variable.
  Return correct error on query of xattr on file with empty xattrs
  cifs: Wait for writebacks to complete before attempting write.

Pull char/misc driver fixes from Greg KH:
 "Here are a few driver fixes for char/misc drivers that resolve
  reported issues.

  All have been in linux-next successfully for a few days"

* tag 'char-misc-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Drivers: hv: vmbus: Negotiate version 3.0 when running on ws2012r2 hosts
  Tools: hv: Handle the case when the target file exists correctly
  vme_tsi148: Utilize to_pci_dev() macro
  vme_tsi148: Fix PCI address mapping assumption
  vme_tsi148: Fix typo in tsi148_slave_get()
  w1: avoid recursive device_add
  w1: fix netlink refcnt leak on error path
  misc: Grammar s/addition/additional/
  drivers: mcb: fix memory leak in chameleon_parse_cells() error path
  mei: ignore client writing state during cb completion
  mei: me: do not load the driver if the FW doesn't support MEI interface
  GenWQE: Increase driver version number
  GenWQE: Fix multithreading problems
  GenWQE: Ensure rc is not returning an uninitialized value
  GenWQE: Add wmb before DDCB is started
  GenWQE: Enable access to VPD flash area

Merge tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fixes from Greg KH:
 "Here are some driver core fixes for 3.15-rc2.  Also in here are some
  documentation updates, as well as an API removal that had to wait for
  after -rc1 due to the cleanups coming into you from multiple developer
  trees (this one and the PPC tree.)

  All have been in linux next successfully"

* tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  drivers/base/dd.c incorrect pr_debug() parameters
  Documentation: Update stable address in Chinese and Japanese translations
  topology: Fix compilation warning when not in SMP
  Chinese: add translation of io_ordering.txt
  stable_kernel_rules: spelling/word usage
  sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()
  kernfs: protect lazy kernfs_iattrs allocation with mutex
  fs: Don't return 0 from get_anon_bdev

Pull staging driver fixes from Greg KH:
 "Here are a few staging driver fixes for issues that have been reported
  for 3.15-rc2.

  Also dominating the diffstat for the pull request is the removal of
  the rtl8187se driver.  It's no longer needed in staging as a "real"
  driver for this hardware is now merged in the tree in the "correct"
  location in drivers/net/

  All of these patches have been tested in linux-next"

* tag 'staging-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: r8188eu: Fix case where ethtype was never obtained and always be checked against 0
  staging: r8712u: Fix case where ethtype was never obtained and always be checked against 0
  staging: r8188eu: Calling rtw_get_stainfo() with a NULL sta_addr will return NULL
  staging: comedi: fix circular locking dependency in comedi_mmap()
  staging: r8723au: Add missing initialization of change_inx in sort algorithm
  Staging: unisys: use after free in list_for_each()
  staging: unisys: use after free in error messages
  staging: speakup: fix misuse of kstrtol() in handle_goto()
  staging: goldfish: Call free_irq in error path
  staging: delete rtl8187se wireless driver
  staging: rtl8723au: Fix buffer overflow in rtw_get_wfd_ie()
  staging: gs_fpgaboot: remove __TIMESTAMP__ macro
  staging: vme: fix memory leak in vme_user_probe()
  staging: fpgaboot: clean up Makefile
  staging/usbip: fix store_attach() sscanf return value check
  staging/usbip: userspace - fix usbipd SIGSEGV from refresh_exported_devices()
  staging: rtl8188eu: remove spaces, correct counts to unbreak P2P ioctls
  staging/rtl8821ae: Fix OOM handling in _rtl_init_deferred_work()

Pull tty/serial driver fixes from Greg KH:
 "Here are a number of small tty/serial driver fixes for 3.15-rc2.  Also
  in here are some Documentation file removals for drivers that we
  removed a long time ago, no need to keep it around any longer.

  All of these have been in linux-next for a bit"

* tag 'tty-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Revert "serial: 8250, disable "too much work" messages"
  serial: amba-pl011: fix regression, causing an Oops on rmmod
  tty: Fix help text of SYNCLINK_CS
  tty: fix memleak in alloc_pid
  ttyprintk: Allow built as a module
  ttyprintk: Fix wrong tty_unregister_driver() call in the error path
  serial: 8250, disable "too much work" messages
  Documentation/serial: Delete obsolete driver documentation
  serial: omap: Fix missing pm_runtime_resume handling by simplifying code
  serial_core: Fix pm imbalance on unbind
  serial: pl011: change Rx burst size to half of trigger level
  serial: timberdale: Depend on X86_32
  serial: st-asc: Fix SysRq char handling
  Revert "serial: clps711x: Give a chance to perform useful tasks during wait loop"
  serial_core: Fix conditional start_tx on ring buffer not empty
  serial: efm32: use $vendor,$device scheme for compatible string
  serial: omap: free the wakeup settings in remove

Pull USB fixes from Greg KH:
 "Here are a number of tiny USB fixes and new device ids for 3.15-rc2.
  Nothing major, just issues some people have reported.

  All of these have been in linux-next"

* tag 'usb-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  uas: fix deadlocky memory allocations
  uas: fix error handling during scsi_scan()
  uas: fix GFP_NOIO under spinlock
  uwb: adds missing error handling
  USB: cdc-acm: Remove Motorola/Telit H24 serial interfaces from ACM driver
  USB: ohci-jz4740: FEAT_POWER is a port feature, not a hub feature
  USB: ohci-jz4740: Fix uninitialized variable warning
  USB: EHCI: tegra: set txfill_tuning
  usb: ehci-platform: Return immediately from suspend if ehci_suspend fails
  usb: ehci-exynos: Return immediately from suspend if ehci_suspend fails
  USB: fix crash during hotplug of PCI USB controller card
  USB: cdc-acm: fix double usb_autopm_put_interface() in acm_port_activate()
  usb: usb-common: fix typo for usb_state_string
  USB: usb_wwan: fix handling of missing bulk endpoints
  USB: pl2303: add ids for Hewlett-Packard HP POS pole displays
  USB: cp210x: Add 8281 (Nanotec Plug & Drive)
  usb: option driver, add support for Telit UE910v2
  Revert "USB: serial: add usbid for dell wwan card to sierra.c"
  USB: serial: ftdi_sio: add id for Brainboxes serial cards

Merge misc fixes from Andrew Morton:
 "13 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  thp: close race between split and zap huge pages
  mm: fix new kernel-doc warning in filemap.c
  mm: fix CONFIG_DEBUG_VM_RB description
  mm: use paravirt friendly ops for NUMA hinting ptes
  mips: export flush_icache_range
  mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()
  wait: explain the shadowing and type inconsistencies
  Shiraz has moved
  Documentation/vm/numa_memory_policy.txt: fix wrong document in numa_memory_policy.txt
  powerpc/mm: fix ".__node_distance" undefined
  kernel/watchdog.c:touch_softlockup_watchdog(): use raw_cpu_write()
  init/Kconfig: move the trusted keyring config option to general setup
  vmscan: reclaim_clean_pages_from_list() must use mod_zone_page_state()

Sasha Levin has reported two THP BUGs[1][2].  I believe both of them
have the same root cause.  Let's look to them one by one.

The first bug[1] is "kernel BUG at mm/huge_memory.c:1829!".  It's
BUG_ON(mapcount != page_mapcount(page)) in __split_huge_page().  From my
testing I see that page_mapcount() is higher than mapcount here.

I think it happens due to race between zap_huge_pmd() and
page_check_address_pmd().  page_check_address_pmd() misses PMD which is
under zap:

	CPU0						CPU1
						zap_huge_pmd()
						  pmdp_get_and_clear()
__split_huge_page()
  anon_vma_interval_tree_foreach()
    __split_huge_page_splitting()
      page_check_address_pmd()
        mm_find_pmd()
	  /*
	   * We check if PMD present without taking ptl: no
	   * serialization against zap_huge_pmd(). We miss this PMD,
	   * it's not accounted to 'mapcount' in __split_huge_page().
	   */
	  pmd_present(pmd) == 0

  BUG_ON(mapcount != page_mapcount(page)) // CRASH!!!

						  page_remove_rmap(page)
						    atomic_add_negative(-1, &page->_mapcount)

The second bug[2] is "kernel BUG at mm/huge_memory.c:1371!".
It's VM_BUG_ON_PAGE(!PageHead(page), page) in zap_huge_pmd().

This happens in similar way:

	CPU0						CPU1
						zap_huge_pmd()
						  pmdp_get_and_clear()
						  page_remove_rmap(page)
						    atomic_add_negative(-1, &page->_mapcount)
__split_huge_page()
  anon_vma_interval_tree_foreach()
    __split_huge_page_splitting()
      page_check_address_pmd()
        mm_find_pmd()
	  pmd_present(pmd) == 0	/* The same comment as above */
  /*
   * No crash this time since we already decremented page->_mapcount in
   * zap_huge_pmd().
   */
  BUG_ON(mapcount != page_mapcount(page))

  /*
   * We split the compound page here into small pages without
   * serialization against zap_huge_pmd()
   */
  __split_huge_page_refcount()
						VM_BUG_ON_PAGE(!PageHead(page), page); // CRASH!!!

So my understanding the problem is pmd_present() check in mm_find_pmd()
without taking page table lock.

The bug was introduced by me commit with commit 117b0791. Sorry for
that. :(

Let's open code mm_find_pmd() in page_check_address_pmd() and do the
check under page table lock.

Note that __page_check_address() does the same for PTE entires
if sync != 0.

I've stress tested split and zap code paths for 36+ hours by now and
don't see crashes with the patch applied. Before it took <20 min to
trigger the first bug and few hours for second one (if we ignore
first).

[1] https://lkml.kernel.org/g/<53440991.9090001@oracle.com>
[2] https://lkml.kernel.org/g/<5310C56C.60709@oracle.com>
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: NSasha Levin <sasha.levin@oracle.com>
Tested-by: NSasha Levin <sasha.levin@oracle.com>
Cc: Bob Liu <lliubbo@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michel Lespinasse <walken@google.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>	[3.13+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix new kernel-doc warning in mm/filemap.c:

  Warning(mm/filemap.c:2600): Excess function parameter 'ppos' description in '__generic_file_aio_write'
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This appears to be a copy/paste error.  Update the description to
reflect extra rbtree debug and checks for the config option instead of
duplicating CONFIG_DEBUG_VM.
Signed-off-by: NDavidlohr Bueso <davidlohr@hp.com>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

David Vrabel identified a regression when using automatic NUMA balancing
under Xen whereby page table entries were getting corrupted due to the
use of native PTE operations.  Quoting him

	Xen PV guest page tables require that their entries use machine
	addresses if the preset bit (_PAGE_PRESENT) is set, and (for
	successful migration) non-present PTEs must use pseudo-physical
	addresses.  This is because on migration MFNs in present PTEs are
	translated to PFNs (canonicalised) so they may be translated back
	to the new MFN in the destination domain (uncanonicalised).

	pte_mknonnuma(), pmd_mknonnuma(), pte_mknuma() and pmd_mknuma()
	set and clear the _PAGE_PRESENT bit using pte_set_flags(),
	pte_clear_flags(), etc.

	In a Xen PV guest, these functions must translate MFNs to PFNs
	when clearing _PAGE_PRESENT and translate PFNs to MFNs when setting
	_PAGE_PRESENT.

His suggested fix converted p[te|md]_[set|clear]_flags to using
paravirt-friendly ops but this is overkill.  He suggested an alternative
of using p[te|md]_modify in the NUMA page table operations but this is
does more work than necessary and would require looking up a VMA for
protections.

This patch modifies the NUMA page table operations to use paravirt
friendly operations to set/clear the flags of interest.  Unfortunately
this will take a performance hit when updating the PTEs on
CONFIG_PARAVIRT but I do not see a way around it that does not break
Xen.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Acked-by: NDavid Vrabel <david.vrabel@citrix.com>
Tested-by: NDavid Vrabel <david.vrabel@citrix.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Noonan <steven@uplinklabs.net>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The lkdtm module performs tests against executable memory ranges, so it
needs to flush the icache for proper behaviors.  Other architectures
already export this, so do the same for MIPS.

[akpm@linux-foundation.org: relocate export sites]
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>