The same test is done in every EEH report function, so factor it out.

Since eeh_dev_removed() needs to be moved higher up in the file,
simplify it a little while we're at it.
Signed-off-by: NSam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add a for_each-style macro for iterating through PEs without the
boilerplate required by a traversal function. eeh_pe_next() is now
exported, as it is now used directly in place.
Signed-off-by: NSam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

As EEH event handling progresses, a cumulative result of type
pci_ers_result is built up by (some of) the eeh_report_*() functions
using either:
	if (rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
	if (*res == PCI_ERS_RESULT_NONE) *res = rc;
or:
	if ((*res == PCI_ERS_RESULT_NONE) ||
	    (*res == PCI_ERS_RESULT_RECOVERED)) *res = rc;
	if (*res == PCI_ERS_RESULT_DISCONNECT &&
	    rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
(Where *res is the accumulator.)

However, the intent is not immediately clear and the result in some
situations is order dependent.

Address this by assigning a priority to each result value, and always
merging to the highest priority. This renders the intent clear, and
provides a stable value for all orderings.
Signed-off-by: NSam Bobroff <sbobroff@linux.ibm.com>
[mpe: Minor formatting (clang-format)]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

To aid debugging, add a message to show when EEH processing for a PE
will be done at the device's parent, rather than directly at the
device.
Signed-off-by: NSam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The traversal functions eeh_pe_traverse() and eeh_pe_dev_traverse()
both provide their first argument as void * but every single user casts
it to the expected type.

Change the type of the first parameter from void * to the appropriate
type, and clean up all uses.
Signed-off-by: NSam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NSam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Correct two cases where eeh_pcid_get() is used to reference the driver's
module but the reference is dropped before the driver pointer is used.

In eeh_rmv_device() also refactor a little so that only two calls to
eeh_pcid_put() are needed, rather than three and the reference isn't
taken at all if it wasn't needed.
Signed-off-by: NSam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add a single log line at the end of successful EEH recovery, so that
it's clear that event processing has finished.
Signed-off-by: NSam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Since thread-imc internally use the core-imc hardware infrastructure
and is depended on it, having thread-imc in the kernel in the
absence of core-imc is trivial. Patch disables thread-imc, if
core-imc is not registered.
Signed-off-by: NAnju T Sudhakar <anju@linux.vnet.ibm.com>
Reviewed-by: NMadhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Return proper error code for unknown domain during IMC initialization.
Signed-off-by: NAnju T Sudhakar <anju@linux.vnet.ibm.com>
Reviewed-by: NMadhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Replace the direct return statement in imc_mem_init() with goto, to adhere
to the kernel coding style.
Signed-off-by: NAnju T Sudhakar <anju@linux.vnet.ibm.com>
Reviewed-by: NMadhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When any of the IMC (In-Memory Collection counter) devices fail
to initialize, imc_common_mem_free() frees set of memory. In doing so,
pmu_ptr pointer is also freed. But pmu_ptr pointer is used in subsequent
function (imc_common_cpuhp_mem_free()) which is wrong. Patch here reorders
the code to avoid such access.

Also free the memory which is dynamically allocated during imc
initialization, wherever required.
Signed-off-by: NAnju T Sudhakar <anju@linux.vnet.ibm.com>
Reviewed-by: NMadhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The device node obtained with of_find_compatible_node() should be
released by calling of_node_put().  But it was not released when
of_get_property() failed.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
[mpe: Invert the sense of the if so we only need one return path]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Structure platform_driver does not need to set the owner field, as this
will be populated by the driver core.

Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The GETFIELD and SETFIELD macros in xive-regs.h aren't used except for
a single instance of GETFIELD, so replace that and remove them.

These macros are also defined in vas.h, so either those should be
eventually replaced or the macros moved into bitops.h.
Signed-off-by: NRussell Currey <ruscur@russell.cc>
[mpe: Rewrite the assignment to 'he' to avoid ffs() etc.]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

time_init() will set up tb_ticks_per_usec based on reality.
time_init() is called *after* udbg_init_opal_common() during boot.

from arch/powerpc/kernel/time.c:
  unsigned long tb_ticks_per_usec = 100; /* sane default */

Currently, all powernv systems have a timebase frequency of 512mhz
(512000000/1000000 == 0x200) - although there's nothing written
down anywhere that I can find saying that we couldn't make that
different based on the requirements in the ISA.

So, we've been (accidentally) thwacking the (currently) correct
(for powernv at least) value for tb_ticks_per_usec earlier than
we otherwise would have.

The "sane default" seems to be adequate for our purposes between
udbg_init_opal_common() and time_init() being called, and if it isn't,
then we should probably be setting it somewhere that isn't hvc_opal.c!
Signed-off-by: NStewart Smith <stewart@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

to_tm() is now completely unused, the only reference being in the
_dump_time() helper that is also unused. This removes both, leaving
the rest of the powerpc RTC code y2038 safe to as far as the hardware
supports.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

update_persistent_clock() is deprecated because it suffers from overflow
in 2038 on 32-bit architectures. This changes powerpc to use the
update_persistent_clock64() replacement, and to pass down 64-bit
timestamps consistently.

This is now simpler, as we no longer have to worry about the offset
numbers in tm_year and tm_mon that are different between the Linux
conventions and RTAS.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Looking through the remaining users of the deprecated mktime()
function, I found the powerpc rtc handlers, which use it in
place of rtc_tm_to_time64().

To clean this up, I'm changing over the read_persistent_clock()
function to the read_persistent_clock64() variant, and change
all the platform specific handlers along with it.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The to_tm() helper function operates on a signed integer for the time,
so it will suffer from overflow in 2038, even on 64-bit kernels.

Rather than fix that function, this replaces its use in the rtas
procfs implementation with the standard rtc_time64_to_tm() helper
that is very similar but is not affected by the overflow.

In order to actually support long times, the parser function gets
changed to 64-bit user input and output as well. Note that the tm_mon
and tm_year representation is slightly different, so we have to manually
add an offset here.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In order to use the rtc_tm_to_time64() and rtc_time64_to_tm()
helper functions in later patches, we have to ensure that
CONFIG_RTC_LIB is always built-in.

Note that this symbol only controls a couple of helper functions,
not the actual RTC subsystem, which remains optional and is
enabled with CONFIG_RTC_CLASS.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Needed on Amiga X1000 with SB600.
Reported-by: NChristian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When inserting SLB entries for EA above 512TB, we need to hard disable irq.
This will make sure we don't take a PMU interrupt that can possibly touch
user space address via a stack dump. To prevent this, we need to hard disable
the interrupt.

Also add a comment explaining why we don't need context synchronizing isync
with slbmte.

Fixes: f384796c ("powerpc/mm: Add support for handling > 512TB address in SLB miss")
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

With split pmd page table lock enabled, we don't use mm->page_table_lock when
updating pmd entries. This patch update hugetlb path to use the right lock
when inserting huge page directory entries into page table.

ex: if we are using hugepd and inserting hugepd entry at the pmd level, we
use pmd_lockptr, which based on config can be split pmd lock.

For update huge page directory entries itself we use mm->page_table_lock. We
do have a helper huge_pte_lockptr() for that.

Fixes: 675d9952 ("powerpc/book3s64: Enable split pmd ptlock")
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently we do not have an isync, or any other context synchronizing
instruction prior to the slbie/slbmte in _switch() that updates the
SLB entry for the kernel stack.

However that is not correct as outlined in the ISA.

From Power ISA Version 3.0B, Book III, Chapter 11, page 1133:

  "Changing the contents of ... the contents of SLB entries ... can
   have the side effect of altering the context in which data
   addresses and instruction addresses are interpreted, and in which
   instructions are executed and data accesses are performed.
   ...
   These side effects need not occur in program order, and therefore
   may require explicit synchronization by software.
   ...
   The synchronizing instruction before the context-altering
   instruction ensures that all instructions up to and including that
   synchronizing instruction are fetched and executed in the context
   that existed before the alteration."

And page 1136:

  "For data accesses, the context synchronizing instruction before the
   slbie, slbieg, slbia, slbmte, tlbie, or tlbiel instruction ensures
   that all preceding instructions that access data storage have
   completed to a point at which they have reported all exceptions
   they will cause."

We're not aware of any bugs caused by this, but it should be fixed
regardless.

Add the missing isync when updating kernel stack SLB entry.

Cc: stable@vger.kernel.org
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Flesh out change log with more ISA text & explanation]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The stores to update the SLB shadow area must be made as they appear
in the C code, so that the hypervisor does not see an entry with
mismatched vsid and esid. Use WRITE_ONCE for this.

GCC has been observed to elide the first store to esid in the update,
which means that if the hypervisor interrupts the guest after storing
to vsid, it could see an entry with old esid and new vsid, which may
possibly result in memory corruption.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When a single-threaded process has a non-local mm_cpumask, try to use
that point to flush the TLBs out of other CPUs in the cpumask.

An IPI is used for clearing remote CPUs for a few reasons:
- An IPI can end lazy TLB use of the mm, which is required to prevent
  TLB entries being created on the remote CPU. The alternative is to
  drop lazy TLB switching completely, which costs 7.5% in a context
  switch ping-pong test betwee a process and kernel idle thread.
- An IPI can have remote CPUs flush the entire PID, but the local CPU
  can flush a specific VA. tlbie would require over-flushing of the
  local CPU (where the process is running).
- A single threaded process that is migrated to a different CPU is
  likely to have a relatively small mm_cpumask, so IPI is reasonable.

No other thread can concurrently switch to this mm, because it must
have been given a reference to mm_users by the current thread before it
can use_mm. mm_users can be asynchronously incremented (by
mm_activate or mmget_not_zero), but those users must use remote mm
access and can't use_mm or access user address space. Existing code
makes the this assumption already, for example sparc64 has reset
mm_cpumask using this condition since the start of history, see
arch/sparc/kernel/smp_64.c.

This reduces tlbies for a kernel compile workload from 0.90M to 0.12M,
tlbiels are increased significantly due to the PID flushing for the
cleaning up remote CPUs, and increased local flushes (PID flushes take
128 tlbiels vs 1 tlbie).
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Implementing pte_update with pte_xchg (which uses cmpxchg) is
inefficient. A single larx/stcx. works fine, no need for the less
efficient cmpxchg sequence.

Then remove the memory barriers from the operation. There is a
requirement for TLB flushing to load mm_cpumask after the store
that reduces pte permissions, which is moved into the TLB flush
code.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The ISA suggests ptesync after setting a pte, to prevent a table walk
initiated by a subsequent access from missing that store and causing a
spurious fault. This is an architectual allowance that allows an
implementation's page table walker to be incoherent with the store
queue.

However there is no correctness problem in taking a spurious fault in
userspace -- the kernel copes with these at any time, so the updated
pte will be found eventually. Spurious kernel faults on vmap memory
must be avoided, so a ptesync is put into flush_cache_vmap.

On POWER9 so far I have not found a measurable window where this can
result in more minor faults, so as an optimisation, remove the costly
ptesync from pte updates. If an implementation benefits from ptesync,
it would be better to add it back in update_mmu_cache, so it's not
done for things like fork(2).

fork --fork --exec benchmark improved 5.2% (12400->13100).
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Prefetch the faulting address in update_mmu_cache to give the page
table walker perhaps 100 cycles head start as locks are dropped and
the interrupt completed.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This matches other architectures, when we know there will be no
further accesses to the address (e.g., for teardown), page table
entries can be cleared non-atomically.

The comments about NMMU are bogus: all MMU notifiers (including NMMU)
are released at this point, with their TLBs flushed. An NMMU access at
this point would be a bug.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In the case of a spurious fault (which can happen due to a race with
another thread that changes the page table), the default Linux mm code
calls flush_tlb_page for that address. This is not required because
the pte will be re-fetched. Hash does not wire this up to a hardware
TLB flush for this reason. This patch avoids the flush for radix.

>From Power ISA v3.0B, p.1090:

    Setting a Reference or Change Bit or Upgrading Access Authority
    (PTE Subject to Atomic Hardware Updates)

    If the only change being made to a valid PTE that is subject to
    atomic hardware updates is to set the Refer- ence or Change bit to
    1 or to add access authorities, a simpler sequence suffices
    because the translation hardware will refetch the PTE if an access
    is attempted for which the only problems were reference and/or
    change bits needing to be set or insufficient access authority.

The nest MMU on POWER9 does not re-fetch the PTE after such an access
attempt before faulting, so address spaces with a coprocessor
attached will continue to flush in these cases.

This reduces tlbies for a kernel compile workload from 0.95M to 0.90M.

fork --fork --exec benchmark improved 0.5% (12300->12400).
Reviewed-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Radix flushes the TLB when updating ptes to increase permissiveness
of protection (increase access authority). Book3S does not require
TLB flushing in this case, and it is not done on hash. This patch
avoids the flush for radix.

>From Power ISA v3.0B, p.1090:

    Setting a Reference or Change Bit or Upgrading Access Authority
    (PTE Subject to Atomic Hardware Updates)

    If the only change being made to a valid PTE that is subject to
    atomic hardware updates is to set the Reference or Change bit to 1
    or to add access authorities, a simpler sequence suffices because
    the translation hardware will refetch the PTE if an access is
    attempted for which the only problems were reference and/or change
    bits needing to be set or insufficient access authority.

The nest MMU on POWER9 does not re-fetch the PTE after such an access
attempt before faulting, so address spaces with a coprocessor
attached will continue to flush in these cases.

This reduces tlbies for a kernel compile workload from 1.28M to 0.95M,
tlbiels from 20.17M 19.68M.

fork --fork --exec benchmark improved 2.77% (12000->12300).
Reviewed-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When relaxing access (read -> read_write update), pte needs to be marked invalid
to handle a nest MMU bug. We also need to do a tlb flush after the pte is
marked invalid before updating the pte with new access bits.

We also move tlb flush to platform specific __ptep_set_access_flags. This will
help us to gerid of unnecessary tlb flush on BOOK3S 64 later. We don't do that
in this patch. This also helps in avoiding multiple tlbies with coprocessor
attached.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In later patch, we use the vma and psize to do tlb flush. Do the prototype
update in separate patch to make the review easy.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In later patch we will update them which require them to be moved
to pgtable-radix.c. Keeping the function in radix.h results in
compile warning as below.

./arch/powerpc/include/asm/book3s/64/radix.h: In function ‘radix__ptep_set_access_flags’:
./arch/powerpc/include/asm/book3s/64/radix.h:196:28: error: dereferencing pointer to incomplete type ‘struct vm_area_struct’
  struct mm_struct *mm = vma->vm_mm;
                            ^~
./arch/powerpc/include/asm/book3s/64/radix.h:204:6: error: implicit declaration of function ‘atomic_read’; did you mean ‘__atomic_load’? [-Werror=implicit-function-declaration]
      atomic_read(&mm->context.copros) > 0) {
      ^~~~~~~~~~~
      __atomic_load
./arch/powerpc/include/asm/book3s/64/radix.h:204:21: error: dereferencing pointer to incomplete type ‘struct mm_struct’
      atomic_read(&mm->context.copros) > 0) {

Instead of fixing header dependencies, we move the function to pgtable-radix.c
Also the function is now large to be a static inline . Doing the
move in separate patch helps in review.

No functional change in this patch. Only code movement.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In a later patch, we want to update __ptep_set_access_flags take page size
arg. This makes ptep_set_access_flags only work with mmu_virtual_psize.
To simplify the code make huge_ptep_set_access_flags directly call
__ptep_set_access_flags so that we can compute the hugetlb page size in
hugetlb function.

Now that ptep_set_access_flags won't be called for hugetlb remove
the is_vm_hugetlb_page() check and add the assert of pte lock
unconditionally.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NAlastair D'Silva <alastair@d-silva.org>
Acked-by: NFrederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In order for a userspace AFU driver to call the POWER9 specific
OCXL_IOCTL_ENABLE_P9_WAIT, it needs to verify that it can actually
make that call.
Signed-off-by: NAlastair D'Silva <alastair@d-silva.org>
Acked-by: NFrederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In order to successfully issue as_notify, an AFU needs to know the TID
to notify, which in turn means that this information should be
available in userspace so it can be communicated to the AFU.
Signed-off-by: NAlastair D'Silva <alastair@d-silva.org>
Acked-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>