Add device ID for a Dell-branded, Philips device ID transceiver reported
by an OpenELEC user on their forums.

http://openelec.tv/forum/27-hardware-support/5622-adding-support-for-an-ir-receiver--dell-branded--#5622Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There are two "hauppauge-new" keymaps, one with protocol
unknown, and the other with the protocol marked accordingly.
However, both tables are miss-named.

Also, the old rc-hauppauge-new is broken, as it mixes
three different controllers as if they were just one.

This patch solves half of the problem by renaming the
correct keycode table as just rc-hauppauge. This table
contains the codes for the four different types of
remote controllers found on Hauppauge cards, properly
mapped with their different addresses.

 create mode 100644 drivers/media/rc/keymaps/rc-hauppauge.c
 delete mode 100644 drivers/media/rc/keymaps/rc-rc5-hauppauge-new.c
[Jarod: fix up RC_MAP_HAUPPAUGE defines]
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>

There's a Realtek combo card reader and IR receiver device with multiple
usb interfaces on it. The mceusb driver is incorrectly grabbing all of
them. This change should make it bind to only interface 2 (patch based
on lsusb output on the linux-media list from Lucian Muresan).

Tested regression-free with the six mceusb devices I have myself.
Reported-by: NPatrick Boettcher <pboettcher@kernellabs.com>
Reported-by: NLucian Muresan <lucianm@users.sourceforge.net>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make sure rawir struct is zeroed out before populating it for each
ir_raw_event_store_with_filter() call, and when we see a trailing 0x80
packet (end-of-data), issue an ir_raw_event_reset() call.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Due to my own stupidity, some of the wrong time unit conversion macros
were being used inside some of the IR drivers I've been working on. Fix
that, and convert over some additional places to also use the macros.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixes an egregious bug in mceusb driver, where the receiver was being
put into idle mode far sooner than it should have, thanks to storing a
timeout value that in us where it should be ns. Basically, the receiver
kept going into idle mode before a trailing space had been fully
received, which was causing problems for some protocols, most notably
manifesting as lirc userspace never receiving a trailing space for any
rc5 signals.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The ene_ir driver was using a private define of MS_TO_NS, which is meant
to be microseconds to nanoseconds. The mceusb driver copied it,
intending to use is a milliseconds to microseconds. Lets move the
defines to a common location, expand and standardize them a touch, so
that we now have:

  MS_TO_NS - milliseconds to nanoseconds
  MS_TO_US - milliseconds to microseconds
  US_TO_NS - microseconds to nanoseconds
Reported-by: NDavid Härdeman <david@hardeman.nu>
CC: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When trying to create persistent device names for mceusb and streamzap
devices, I noticed that their respective drivers are not creating the rc
device as a child of the USB device. Rather it creates it as virtual
device. As a result, udev cannot use the USB device information to
create persistent device names for event and lirc devices associated
with the rc device. Not having persistent device names makes it more

difficult to make use of the devices in userspace as their names can
change.

Forward-ported to media_tree staging/for_v2.6.38 and tested with
both streamzap and mceusb devices:
$ ll /dev/input/by-id/
...
lrwxrwxrwx. 1 root root 9 Nov 17 17:06 usb-Streamzap__Inc._Streamzap_Remote_Control-event-if00 -> ../event6
lrwxrwxrwx. 1 root root 9 Nov 17 17:05 usb-Topseed_Technology_Corp._eHome_Infrared_Transceiver_TS000BzY-event-if00 -> ../event5
Previously, nada.
Signed-off-by: NPaul Bender <pebender@gmail.com>
Tested-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,IR_TYPE,RC_TYPE,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_type,rc_type,g <$i >a && mv a $i; done
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Remote Controller subsystem is meant to be used not only by Infra Red
but also for similar types of Remote Controllers. The core is not specific
to Infra Red. As such, rename:
	- ir-core.h to rc-core.h
	- IR_CORE to RC_CORE
	- namespace inside rc-core.c/rc-core.h

To be consistent with the other changes.

No functional change on this patch.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch merges the ir_input_dev and ir_dev_props structs into a single
struct called rc_dev. The drivers and various functions in rc-core used
by the drivers are also changed to use rc_dev as the primary interface
when dealing with rc-core.

This means that the input_dev is abstracted away from the drivers which
is necessary if we ever want to support multiple input devs per rc device.

The new API is similar to what the input subsystem uses, i.e:
rc_device_alloc()
rc_device_free()
rc_device_register()
rc_device_unregister()

[mchehab@redhat.com: Fix compilation on mceusb and cx231xx, due to merge conflicts]
Signed-off-by: NDavid Härdeman <david@hardeman.nu>
Acked-by: NJarod Wilson <jarod@redhat.com>
Tested-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Its possible for the call to read rx timeout from the hardware to fail,
in which case we end up with a bogus rx timeout value. Set a default one
when filling in the rc struct, and we'll just overwrite it later w/the
value from hardware, but if that read fails, we've at least got a sane
rx timeout value to work with (1000ms is the default value I've seen
returned on most if not all mceusb hardware).
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As it turns out, somewhere along the way, we managed to invert the
meaning of the tx_mask_inverted flag. Looking back over the old lirc
driver, tx_mask_inverted was set to 0 if the device was in tx_mask_list.
Now we have a tx_mask_inverted flag set to 1 for all the devices that
were in the list, and set tx_mask_inverted to that flag value, which is
actually the opposite of what we used to set, causing set_tx_mask to use
the wrong mask setting option. Since there seem to be more devices with
inverted masks than not (using the original device as the baseline for
inverted vs. normal), lets just call the ones currently marked as
inverted normal instead, and flip the if/else actions that key off of
the inverted flag.

Note: the problem only cropped up if a call to set_tx_mask was made, if
no mask was set, the device would work just fine, which is why this
managed to slip though w/o getting noticed until now.

Tested successfully by myself and Dennis Gilmore.
Reported-by: NDennis Gilmore <dgilmore@redhat.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When trying to create persistent device names for mceusb and streamzap
devices, I noticed that their respective drivers are not creating the rc
device as a child of the USB device. Rather it creates it as virtual
device. As a result, udev cannot use the USB device information to
create persistent device names for event and lirc devices associated
with the rc device. Not having persistent device names makes it more
difficult to make use of the devices in userspace as their names can
change.
Signed-off-by: NPaul Bender <pebender@gmail.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Something I failed to notice while testing the mceusb RLE buffer
decoding simplification patches was that we were getting an extra event
from the previously pressed key.

As was pointed out to me on irc by Maxim, this is actually due to using
ir_raw_event_store_with_filter without having set up a timeout value.
The hardware has a timeout value we're now reading and storing, which
properly enables the transition to idle in the raw event storage
process, and makes IR decode behave correctly w/o keybounce.

Also remove no-longer-used ir_raw_event struct from mceusb_dev struct
and add as-yet-unused enable flags for carrier reports and learning
mode, which I'll hopefully start wiring up sooner than later. While
looking into that, found evidence that 0x9f 0x15 responses are only
non-zero when the short-range learning sensor is used, so correct the
debug spew message, and then suppress it when using the standard
long-range sensor.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If we pass in an offset, we shouldn't skip 2 bytes. And the first-gen
hardware generates a constant stream of interrupts, always with two
header bytes, and if there's been no IR, with nothing else. Bail from
ir processing without calling ir_handle_raw_event when we get such a
buffer delivered to us.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

We were storing a bunch of spaces at the end of each signal, rather than
a single long space. The in-kernel decoders were actually okay with
this, but lirc isn't. As suggested by David Härdeman, switch to storing
samples using ir_raw_event_store_with_filter, which auto-merges the
consecutive space samples for us. This also allows us to bypass having
to store rawir samples in our device struct, further simplifying the
buffer parsing state machine. Both in-kernel decoders and lirc are happy
again with this change.

Also included in this patch is proper parsing of 0x9f 0x01 commands, the
removal of some magic number usage and some printk spew fixups.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Another multi-function Conexant device. Interface 0 is IR, though on
this model, TX isn't wired up at all, so I've mixed in support for
models without TX (and verified that lircd says TX isn't supported when
trying to send w/this device).
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Provides more complete debug spew, parses individual commands and raw IR
data one chunk at a time.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

And replace usage of hex values w/symbolic names wherever possible
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It is better to use a per-model device name, especially on
multi-function devices like Polaris. So, allow overriding the
default name at the mceusb model table.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>

Especially when used with Polaris boards, devices may have different
types of remotes shipped. So, we need a per-model rc-map.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>

The previous logic needed duplicate USB table structs, one to store
the list of the devices, and 3 sets of other structs, to store the
quirks list.

With this change, devices that require expecial quirks just need to
have a .driver_info = <quirk entry>.

It also allows adding some extra quirks, like per-model RC tables.

As a bonus, this patch reduced in 10% the data segment size:

   text    data     bss     dec     hex filename
  15487    5008       4   20499    5013 old/mceusb.ko
  15438    4496       4   19938    4de2 new/mceusb.ko
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>

Switch to a state machine that properly handles all incoming urb data
packets, and reads much cleaner and corrects some minor parsing errors
that were hindering decode on cx231xx/Polaris integrated IR. Also tested
with four different mceusb variants, and works perfectly with all of
them (at least for the rc6a mce remotes).
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>

For now, it adds support for Conexant EVK and for Pixelview.
We should probably find a better way to specify all Conexant
Polaris devices, to avoid needing to repeat this setup on
both mceusb and cx231xx-cards.
Reviewed-by: NJarod Wilson <jarod@redhat.com>
Acked-by: NSri Devi <Srinivasa.Deevi@conexant.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add new event types for timeout & carrier report
Move timeout handling from ir_raw_event_store_with_filter to
ir-lirc-codec, where it is really needed.
Now lirc bridge ensures proper gap handling.
Extend lirc bridge for carrier & timeout reports

Note: all new ir_raw_event variables now should be initialized
like that: DEFINE_IR_RAW_EVENT(ev);

To clean an existing event, use init_ir_raw_event(&ev);
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Acked-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Reported in lirc sf.net tracker and on lirc mailing list
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The ir_input_dev gets filled in by __ir_input_register, the one
allocated in mceusb_init_input_dev was being overwritten by the correct
one shortly after it was initialized (ultimately resulting in a memory
leak). This bug was inherited from imon.c, and was pointed out to me by
Maxim Levitsky.

v2: fix incorrect dev arg to dev_dbg
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Spent a while last night getting device initialization packet captures
under Windows for all generations of devices. There are a few places
where we were doing things differently, and few things we were doing
that we don't need to do, particularly on gen3 hardware, and I *think*
one of those things is what was locking up my pinnacle hw from time to
time -- at least, its been perfectly well behaved every time its been
plugged in since making this change.

First up, we're adding a bit more to the gen1 init routine here. Its
not absolutely necessary, the hardware works the same both with and
without it, but I'd like to be consistent w/Windows here.

Second, DEVICE_RESET is never called when initializing either of my
gen3 devices, its only called for gen1 and gen2. The bits in the gen3
init after removing that, are safe (and interesting) to run on all
hardware, so there's no more gen3-specific init done, there's instead
a generic mceusb_get_parameters() that is run for all hardware.

Third, the gen3 flag isn't needed. We only care if hardware is gen3
during probe, so I've dropped that from the device flags struct.

Successfully tested on all three generations of mceusb hardware.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Prior init unification/simplification patch made these unused, forgot
to remove them, so this silences:

drivers/media/IR/mceusb.c: In function ‘mceusb_gen1_init’:
drivers/media/IR/mceusb.c:769: warning: unused variable ‘partial’
drivers/media/IR/mceusb.c:768: warning: unused variable ‘i’
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Started out as an effort to try to tackle the last remaining issue I'm
having with this damned pinnacle device getting wedged the first time
its plugged in after an indeterminate length of not being plugged in.
Didn't get that solved yet, but did streamline the init code a bit more
and remove some superfluous gunk. Nukes a completely unneeded call to
usb_device_init() and several lines of overly complex crap in the gen1
device init path.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

mchehab: merged with IR/mceusb: userspace buffer copy moved out of driver

    Userspace buffer copy moved out of driver and into lirc bridge driver

[mchehab@redhat.com: merged the patch to avoid compilation errors with allyesconfig ]
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I have pinnacle hardware now. None of this pinnacle-specific crap is at
all necessary (in fact, some of it needed to be removed to actually make
it work). The only thing unique about this device is that it often
transfers inbound data w/a header of 0x90, meaning 16 bytes of IR data
following it, so I had to make adjustments for that, and now its working
perfectly fine.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The first-gen mceusb device init code, while mostly functional, had a few
issues in it. This patch does the following:

1) removes use of magic numbers
2) eliminates mapping of memory from stack
3) makes debug spew translator functional

Additionally, this clean-up revealed that we cannot read the proper default
tx blaster bitmask from the device, we do actually have to initialize it
ourselves, which requires use of a somewhat gross list-based mask inversion
check.

This patch also removes the entirely unnecessary use of struct ir_input_state.

Also supersedes two earlier patches that also touched on first-gen
cleanup, but were partially botched. This one actually compiles, works,
etc., I swear. ;)
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Was using input_unregister_device directly, instead of using
ir_input_unregister, which tears down a bunch of other things in
addition to eventually calling input_unregister_device.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is a new driver for the Windows Media Center Edition/eHome
Infrared Remote transceiver devices. Its a port of the current
lirc_mceusb driver to ir-core, and currently lacks transmit support,
but will grow it back soon enough... This driver also differs from
lirc_mceusb in that it borrows heavily from a simplified IR buffer
decode routine found in Jon Smirl's earlier ir-mceusb port.

This driver has been tested on the original first-generation MCE IR
device with the MS vendor ID, as well as a current-generation device
with a Topseed vendor ID. Every receiver supported by lirc_mceusb
should work equally well. Testing was done primarily with RC6 MCE
remotes, but also briefly with a Hauppauge RC5 remote, and all works
as expected.

v2: fix call to ir_raw_event_handle so repeats work as they should.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>