Adding support for processing of MAPv5 downlink packets.
It involves parsing the Mapv5 packet and checking the csum header
to know whether the hardware has validated the checksum and is
valid or not.

Based on the checksum valid bit the corresponding stats are
incremented and skb->ip_summed is marked either CHECKSUM_UNNECESSARY
or left as CHEKSUM_NONE to let network stack revalidate the checksum
and update the respective snmp stats.

Current MAPV1 header has been modified, the reserved field in the
Mapv1 header is now used for next header indication.
Signed-off-by: NSharath Chandra Vurukala <sharathv@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding documentation explaining the new MAPv4/v5 packet formats
and the corresponding checksum offload headers.
Signed-off-by: NSharath Chandra Vurukala <sharathv@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
iwl-next Intel Wired LAN Driver Updates 2021-06-01

This pull request is targeting net-next and rdma-next branches.
These patches have been reviewed by netdev and rdma mailing lists[1].

This series adds RDMA support to the ice driver for E810 devices and
converts the i40e driver to use the auxiliary bus infrastructure
for X722 devices. The PCI netdev drivers register auxiliary RDMA devices
that will bind to auxiliary drivers registered by the new irdma module.

[1] https://lore.kernel.org/netdev/20210520143809.819-1-shiraz.saleem@intel.com/
---
v3:
- ice_aq_add_rdma_qsets(), ice_cfg_vsi_rdma(), ice_[ena|dis]_vsi_rdma_qset(),
and ice_cfg_rdma_fltr() no longer return ice_status
- Remove null check from ice_aq_add_rdma_qsets()

v2:
- Added patch 'i40e: Replace one-element array with flexible-array
member'

Changes since linked review (v6):
- Removed unnecessary checks in i40e_client_device_register() and
i40e_client_device_unregister()
- Simplified the i40e_client_device_register() API
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

informations  ==> information
typicaly  ==> typically
derrive  ==> derive
eventhough  ==> even though
Signed-off-by: NZheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

wierdness  ==> weirdness
multicat  ==> multicast
limite  ==> limit
adddress  ==> address
operater  ==> operator
intial  ==> initial
smaler  ==> smaller
Communcation  ==> Communication
funcitons  ==> functions
everytime  ==> every time
Neigbor  ==> Neighbor
performace  ==> performance
Signed-off-by: NZheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

possibile  ==> possible
Signed-off-by: NZheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: NDavid Ahern <dsahern@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Suppport  ==> Support
Signed-off-by: NZheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

underlaying  ==> underlying
Signed-off-by: NZheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When kalloc or kmemdup failed, should return ENOMEM rather than ENOBUF.
Signed-off-by: NZheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When kalloc or kmemdup failed, should return ENOMEM rather than ENOBUF.
Signed-off-by: NZheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If CONFIG_IGB_HWMON is n, gcc warns:

drivers/net/ethernet/intel/igb/e1000_82575.c:2765:17:
 warning: ‘e1000_emc_therm_limit’ defined but not used [-Wunused-const-variable=]
 static const u8 e1000_emc_therm_limit[4] = {
                 ^~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/igb/e1000_82575.c:2759:17:
 warning: ‘e1000_emc_temp_data’ defined but not used [-Wunused-const-variable=]
 static const u8 e1000_emc_temp_data[4] = {
                 ^~~~~~~~~~~~~~~~~~~

Move it into #ifdef block to fix this.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If CONFIG_PCI_IOV is n, make W=1 warns:

drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:3909:33:
 warning: ‘cxgb4_mgmt_ethtool_ops’ defined but not used [-Wunused-const-variable=]
 static const struct ethtool_ops cxgb4_mgmt_ethtool_ops = {
                                 ^~~~~~~~~~~~~~~~~~~~~~

Move it into #ifdef block to fix this.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If CONFIG_PROC_FS is n, gcc warns:

drivers/net/hamradio/bpqether.c:437:36:
 warning: ‘bpq_seqops’ defined but not used [-Wunused-const-variable=]
 static const struct seq_operations bpq_seqops = {
                                    ^~~~~~~~~~
Use #ifdef macro to gurad this.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On Intel platforms, not all safety features are enabled on the hardware.
The current implementation enable all safety features by default. This
will cause mass error and warning printouts after the module is loaded.

Introduce platform specific safety features flag to enable or disable
each safety features.
Signed-off-by: NWong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the case MICROREAD_CB_TYPE_READER_ALL clang reports a dead code
warning. The error code assigned to variable err is already passed
to async_cb(). The assignment is redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: NNigel Christian <nigel.l.christian@gmail.com>
Reviewed-by: NKrzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Peng Li says:

====================
net: hdlc: clean up some code style issues

This patchset clean up some code style issues.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Braces {} should be used on all arms of this statement.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Should not use assignment in if condition.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the chackpatch.pl, comparison to NULL could
be written "!param".
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the chackpatch.pl,
EXPORT_SYMBOL(foo); should immediately follow its function/variable.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the checkpatch error as "foo* bar" and should be "foo *bar".
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the checkpatch error about missing a blank line
after declarations.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes some redundant blank lines.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Boris Sukholitko says:

====================
net/sched: act_vlan: Fix modify to allow 0

Currently vlan modification action checks existence of vlan priority by
comparing it to 0. Therefore it is impossible to modify existing vlan
tag to have priority 0.

For example, the following tc command will change the vlan id but will
not affect vlan priority:

tc filter add dev eth1 ingress matchall action vlan modify id 300 \
        priority 0 pipe mirred egress redirect dev eth2

The incoming packet on eth1:

ethertype 802.1Q (0x8100), vlan 200, p 4, ethertype IPv4

will be changed to:

ethertype 802.1Q (0x8100), vlan 300, p 4, ethertype IPv4

although the user has intended to have p == 0.

The fix is to add tcfv_push_prio_exists flag to struct tcf_vlan_params
and rely on it when deciding to set the priority.

The same flag is used to avoid dumping unset vlan priority.

Change Log:
v3 -> v4:
- revert tcf_vlan_get_fill_size change: total size calculation may race vs dump

v2 -> v3:
- Push assumes that the priority is being set
- tcf_vlan_get_fill_size accounts for priority existence

v1 -> v2:
- Do not dump unset priority and fix tests accordingly
- Test for priority 0 modification
====================
Reviewed-by: NDavide Caratti <dcaratti@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because explicitly being set, the priority 0 should appear
in the output.
Signed-off-by: NBoris Sukholitko <boris.sukholitko@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dump vlan priority only if it has been previously set.

Fix the tests accordingly.
Signed-off-by: NBoris Sukholitko <boris.sukholitko@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently vlan modification action checks existence of vlan priority by
comparing it to 0. Therefore it is impossible to modify existing vlan
tag to have priority 0.

For example, the following tc command will change the vlan id but will
not affect vlan priority:

tc filter add dev eth1 ingress matchall action vlan modify id 300 \
        priority 0 pipe mirred egress redirect dev eth2

The incoming packet on eth1:

ethertype 802.1Q (0x8100), vlan 200, p 4, ethertype IPv4

will be changed to:

ethertype 802.1Q (0x8100), vlan 300, p 4, ethertype IPv4

although the user has intended to have p == 0.

The fix is to add tcfv_push_prio_exists flag to struct tcf_vlan_params
and rely on it when deciding to set the priority.

Fixes: 45a497f2 (net/sched: act_vlan: Introduce TCA_VLAN_ACT_MODIFY vlan action)
Signed-off-by: NBoris Sukholitko <boris.sukholitko@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a spelling mistake in a dev_warning message. Fix it.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Variable 'len' is set to conn_info->max_pkt_payload_len but this
value is never read as it is overwritten with a new value later on,
hence it is a redundant assignment and can be removed.

Clean up the following clang-analyzer warning:

net/nfc/nci/hci.c:164:3: warning: Value stored to 'len' is never read
[clang-analyzer-deadcode.DeadStores]
Reported-by: NAbaci Robot <abaci@linux.alibaba.com>
Signed-off-by: NYang Li <yang.lee@linux.alibaba.com>
Reviewed-by: NKrzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

variable 'status' is unneeded and it's noneed to check the
return value of function vxge_reset_all_vpaths,so declare
it as void.
Signed-off-by: NZheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support get_pauseparam and set_pauseparam of ethtool_ops.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function 'qlcnic_82xx_hw_write_wx_2M' is declared twice, so remove the
repeated declaration.

Cc: Shahed Shaikh <shshaikh@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Cc: GR-Linux-NIC-Dev@marvell.com
Signed-off-by: NShaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No functional change.
Signed-off-by: NZhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the refactoring introduced in commit 87614b93 ("net: enetc:
create a common enetc_pf_to_port helper"), enetc_pf_to_port was coded up
to return -1 in case the passed PCIe device does not have a recognized
BDF.

Make sure the -1 value is checked by the callers, to appease static
checkers.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

write_msg(netconsole.c:836) calls netpoll_send_udp after a call to
spin_lock_irqsave, which normally disables interrupts; but in PREEMPT_RT
this call just locks an rt_mutex without disabling irqs. In this case,
netpoll_send_udp is called with interrupts enabled.
Signed-off-by: NWander Lairson Costa <wander@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vadym Kochan says:

====================
Marvell Prestera Switchdev initial updates for firmware version 3.0

This series adds minimal support for firmware version 3.0 which
has such changes like:

    - initial routing support

    - LAG support

    - events interrupt handling changes

Changes just make able to work with new firmware version but
supported features in driver will be added later.

New firmware version was recently merged into linux-firmware tree.

Added ability of loading previous fw major version if the latest one
is missing, also add support for previous FW ABI.

PATCH -> RFC:
    1) Load previous fw version if the latest one is missing (suggested by Andrew Lunn)

    2) Add support for previous FW ABI version (suggested by Andrew Lunn)

RFC v2:
    1) Get rid of automatic decrementing of
       major version but hard code it.

    2) Print error message with file path if
       previous FW could not be loaded.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lets try to load previous fw version in case the latest one is missing on
existing system.
Signed-off-by: NVadym Kochan <vkochan@marvell.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New firmware version has some ABI and feature changes like:

    - LAG support
    - initial L3 support
    - changed events handling logic
Signed-off-by: NVadym Kochan <vkochan@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Latest FW IPC flood message format was changed to configure uc/mc
flooding separately, so change code according to this.
Signed-off-by: NVadym Kochan <vkochan@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are change in firmware which requires that receiver will
disable event interrupts before handling them and enable them
after finish with handling. Events still may come into the queue
but without receiver interruption.
Signed-off-by: NVadym Kochan <vkochan@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>