For aggregated frames with block ack, different status flag
will be used as part of tx command response.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Tx command response sent to host by uCode after completed
the transmission attempt. The status parameter indicates
whether the transmission was successful, or else why if failed.

Here we keep the counters to help understand the different failure
cases.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

If uCode fail to transmit frame, it will send reply tx back
to driver with failure status; keep the counters of each failure
cases for debugging.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Include bt_status_read function pointer for 5150 device
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The patch titled "ath9k: Add new file init.c" shuffled some code
around but in dong so for some reason also removed the revision
check for disablign power save. Add this revision check again
so we can get power save re-enabled again by default on cards
newer than AR5416 and AR5418.

$ git describe --contains 55624204
v2.6.34-rc1~233^2~49^2~343

This patch has fixes for stable kernels [2.6.34+].

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch:

commit 293dc5df
Author: Gabor Juhos <juhosg@openwrt.org>
Date:   Fri Jun 19 12:17:48 2009 +0200

    ath9k: remove ath_rx_ps_back_to_sleep helper

    This helper only clears the SC_OP_WAIT_FOR_{BEACON,CAB} flags.
    Remove it and clear these flags directly in the approptiate
    places instead.

    Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

introduced a regression which forgot to lift the beacon flag
after we received all broadcast and multicast data. This meant
we never went to sleep consuming about ~650mW on idle. This pretty
much broke power save completely.

This patch has fixes for stable kernels [2.6.32+].

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Sameer Nanda <snanda@google.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some buggy APs do not respond to unicast probe requests
or send unicast probe requests very delayed so in the
worst case we should try to send broadcast probe requests,
otherwise we can get disconnected from these APs.

Even if drivers do not have filters to disregard probe
responses from foreign APs mac80211 will only process
probe responses from our associated AP for re-arming
connection monitoring.

We need to do this since the beacon monitor does not
push back the connection monitor by design so even if we
are getting beacons from these type of APs our connection
monitor currently relies heavily on the way the probe
requests are received on the AP. An example of an AP
affected by this is the Nexus One, but this has also been
observed with random APs.

We can probably optimize this later by using null funcs
instead of probe requests.

For more details refer to:

http://code.google.com/p/chromium-os/issues/detail?id=5715

This patch has fixes for stable kernels [2.6.35+].

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The beacon monitor should be disabled when going off channel
to prevent spurious warnings and triggering connection
deterioration work such as sending probe requests. Re-enable
the beacon monitor once we come back to the home channel.

This patch has fixes for stable kernels [2.6.34+].

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This will be used by other components next. The beacon
monitor was added as of 2.6.34 so these fixes are applicable
only to kernels >= 2.6.34.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we go offchannel mac80211 currently leaves alive the
connection idle monitor. This should be instead postponed
until we come back to our home channel, otherwise by the
time we get back to the home channel we could be triggering
unecesary probe requests. For APs that do not respond to
unicast probe requests (Nexus One is a simple example) this
means we essentially get disconnected after the probes
fails.

This patch has stable fixes for kernels [2.6.35+]

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Upon beacon loss we send probe requests after 30 seconds of idle
time and we wait for each probe response 1/2 second. We send a
total of 3 probe requests before giving up on the AP. In the case
that we reset the connection idle monitor we should reset the probe
requests count to 0. Right now this won't help in any way but
the next patch will.

This patch has fixes for stable kernel [2.6.35+].

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This will be used in another place later. The connection
monitor was added as of 2.6.35 so these fixes will be
applicable to >= 2.6.35.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k's entire logic with SC_OP_SCANNING is incorrect due to the
way mac80211 currently implements the scan complete callback and
we handle it in ath9k. This patch removes the flag completely in
preference for the SC_OP_OFFCHANNEL which is really what we wanted.

The scanning flag was used to ensure we reset ANI to the old values
when we go back to the home channel, but if we are offchannel we
use some defaults. The flag was also used to re-enable the TX monitor.

Without this patch we simply never re-enabled ANI and the TX monitor
after going offchannel. This means that after one background
scan we are prone to noise issues and if we had a TX hang we would
not recover. To get this to work properly we must enable ANI after
we have configured the beacon timers, otherwise hardware acts really
oddly.

This patch has stable fixes which apply down to [2.6.36+], there
*may* be a to fix this on older kernels but requires a bit of
work since this patch relies on the new mac80211 flag
IEEE80211_CONF_OFFCHANNEL which was introduced as of 2.6.36.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we return to the home channel we were never reseting our beacon
timers, this was casued by the fact that the scanning flag was still
on even after we returned to our home channel. There are also other
reasons why we would get a reset and if we are not off channel
we always need to resynch our beacon timers, because a reset will
clear them.

This bug is a regression introduced on 2.6.36. The order of the
changes are as follows:

5ee08656 - Sat Jul 31 - ath9k: prevent calibration during off-channel activity
a0daa0e7 - Tue Jul 27 - Revert "mac80211: fix sw scan bracketing"
543708be - Fri Jun 18 - mac80211: fix sw scan bracketing

mcgrof@tux ~/linux-2.6-allstable (git::master)$ git describe \
        --contains 5ee08656
v2.6.36-rc1~43^2~34^2~22

mcgrof@tux ~/linux-2.6-allstable (git::master)$ git describe \
        --contains a0daa0e7
v2.6.36-rc1~571^2~64^2~13

mcgrof@tux ~/linux-2.6-allstable (git::master)$ git describe \
        --contains 543708be
v2.6.36-rc1~571^2~107^2~187

So 5ee08656 would have worked if a0daa0e7 was not committed but
it was so this means 5ee08656 was broken since it assumed that
when we were in the channel change routine the scan flag would
be lifted. As it turns out the scan flag will be set when we
are already on the home channel.

For more details refer to:

http://code.google.com/p/chromium-os/issues/detail?id=5715

These issues will need to be considered for our solution on
reshifting the scan complete callback location on mac80211 on
current development kernel work.

This patch has stable fixes which apply down to [2.6.36+]

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k has a race on putting the chip into network sleep and
having registers read from hardware. The race occurs because
although ath9k_ps_restore() locks its own callers it makes use
of some variables which get altered in the driver at different
code paths. The variables are the ps_enabled and ps_flags.

This is easily reprodicible in large network environments when
roaming with the wpa_supplicant simple bgscan. You'd get some
0xdeadbeef read out on certain registers such as:

ath: timeout (100000 us) on reg 0x806c: 0xdeadbeef & 0x01f00000 != 0x00000000
ath: RX failed to go idle in 10 ms RXSM=0xdeadbeef

ath: timeout (100000 us) on reg 0x7000: 0xdeadbeef & 0x00000003 != 0x00000000
ath: Chip reset failed

The fix is to protect the ath9k_config(hw, IEEE80211_CONF_CHANGE_PS)
calls with a spin_lock_irqsave() which will disable contendors for
these variables from interrupt context, timers, re-entry from mac80211
on the same callback, and most importantly from ath9k_ps_restore()
which is the only call which will put the device into network sleep.

There are quite a few threads and bug reports on these a few of them are:

https://bugs.launchpad.net/ubuntu/karmic/+source/linux/+bug/407040
http://code.google.com/p/chromium-os/issues/detail?id=5709
http://code.google.com/p/chromium-os/issues/detail?id=5943

Stable fixes apply to [2.6.32+]

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To optimize register read/write operations, the HTC firmwares were patched
to change EP3 and EP4 pipe types from Interrupt to Bulk. So register writes
are submitted as bulk urbs, but register reads are not. Also changing the
register read endpoint pipe as bulk type when URBs are filled improves the
register reads considerably which results in reduced scan time and CPU
utilization.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a driver advertises p2p device support,
mac80211 will handle it, but internally it will
rewrite the interface type to STA/AP rather than
P2P-STA/GO since otherwise a lot of paths need
to be touched that are otherwise identical. A
p2p boolean tells drivers whether or not a given
interface will be used for p2p or not.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds P2P-STA and P2P-GO as device types so
we can distinguish between those and normal STA
or AP (respectively) type interfaces.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes following warning

drivers/net/wireless/ath/ath9k/eeprom_def.c: In function 'ath9k_hw_def_get_num_ant_config'
drivers/net/wireless/ath/ath9k/eeprom_def.c:1425:47: warning: comparison
			between 'enum ath9k_hal_freq_band' and 'enum ieee80211_band'
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  CHECK   drivers/net/wireless/libertas/cfg.c
drivers/net/wireless/libertas/cfg.c:493:19: warning: cast to restricted __le16
  CHECK   drivers/net/wireless/libertas/mesh.c
drivers/net/wireless/libertas/mesh.c:577:16: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/mesh.c:577:16:    expected restricted __le32 [addressable] [assigned] [usertype] id
drivers/net/wireless/libertas/mesh.c:577:16:    got bool
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  CHECK   drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/ath/ath9k/recv.c:1341:6: warning: symbol 'ath_ant_div_conf_fast_divbias' was not declared. Should it be static?
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/iwlwifi/iwl-scan.c:386:27: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:386:27:     int enum nl80211_band  versus
drivers/net/wireless/iwlwifi/iwl-scan.c:386:27:     int enum ieee80211_band
drivers/net/wireless/iwlwifi/iwl-scan.c:435:57: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:435:57:     int enum ieee80211_band  versus
drivers/net/wireless/iwlwifi/iwl-scan.c:435:57:     int enum nl80211_band
drivers/net/wireless/iwlwifi/iwl-scan.c:474:53: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:474:53:     int enum ieee80211_band  versus
drivers/net/wireless/iwlwifi/iwl-scan.c:474:53:     int enum nl80211_band
drivers/net/wireless/iwlwifi/iwl-scan.c:588:72: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:588:72:     int enum ieee80211_band  versus
drivers/net/wireless/iwlwifi/iwl-scan.c:588:72:     int enum nl80211_band
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When an interface is brought up, the recent changes
to allow changing type-while-up only set the running
bit after everything was done. This broke a number
of things, including idle calculation for monitor
interfaces, and it also broke WDS station insertion
(although nobody noticed yet).

Thus, change the code to set the running bit earlier,
but keep it after the driver's add_interface was
called because otherwise drivers may iterate over
interfaces they haven't fully set up yet.
Reported-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of using a WARN_ON(!mutex_is_locked())
use lockdep_assert_held() which compiles away
completely when lockdep isn't enabled, and
also is a more accurate assertion since it
checks that the current thread is holding the
mutex.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This code is modifying the station flags, and
as such should hold the flags lock so it can
do so atomically vs. other flags modifications
and readers. This issue was introduced when
this code was added in eccb8e8f, as it used
the wrong lock (thus not fixing the race that
was previously documented in a comment.)

Cc: stable@kernel.org [2.6.31+]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Print raw and decoded rxfilter in debufs 'wiphy' file.

Also, move variable-length printouts to bottom of file to
make bounds checking easier.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When there is more than one VIF, listen for all beacons
and ensure ATH9K_RX_FILTER_MCAST_BCAST_ALL is set.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use key management functions which have been moved to ath/key.c and remove
ath9k copies of these functions and other now unused definitions.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replace ah_aes_support and ah_combined_mic with common ath_crypt_caps
ATH_CRYPT_CAP_CIPHER_AESCCM and ATH_CRYPT_CAP_MIC_COMBINED.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replace common->splitmic with ATH_CRYPT_CAP_MIC_COMBINED flag.

splitmic has to be used when the ATH_CRYPT_CAP_MIC_COMBINED capability flag is
not set.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the old ath5k key handling functions, since we now use the key
management in ath common.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use common ath key management functions in ath5k. This fixes problems with HW
encryption in AP mode, which was broken in the ath5k implementation.

Before (with the ath5k implementation) only one client could connect to the AP
using HW encryption and WPA. When a second client connected, the first client
was not able to send/receive any more packets. Because of the problems with HW
encryption, software encryption was always used in AP mode, which resulted in a
high CPU load (and/or low thruput) on embedded devices. Instead of trying to
fix the implementation in ath5k it makes more sense to share the code with
ath9k.

This also enables HW encryption for AP mode again.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Copied the key cache management functions from ath9k (common.c and hw.c) to
ath/key.c so we can use them from ath5k, later.

Minor changes have been made:
 - renamed ath9k_* to ath_*
 - replaced ah->caps.keycache_size with common->keymax
 - removed ATH9K_IS_MIC_ENABLED since it is always true.
 - the AR_PCU_MIC_NEW_LOC_ENA flag is replaced with (splitmic == 0).
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This will be used later in this patch series.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The output becomes:

[   41.261941] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These were introduced in "wl1271: sdio: claim host only when doing IO"

drivers/net/wireless/wl12xx/wl1271_sdio.c: In function ‘wl1271_sdio_set_power’:
drivers/net/wireless/wl12xx/wl1271_sdio.c:193: warning: ‘return’ with a value, in function returning void
drivers/net/wireless/wl12xx/wl1271_sdio.c:195: warning: ‘return’ with a value, in function returning void
drivers/net/wireless/wl12xx/wl1271_sdio.c:186: warning: unused variable ‘func’
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

sta_info_get_bss() is used to match STA pointers
for VLAN/AP interfaces, but if the same station
is also added to multiple other interfaces it
will erroneously match because both pointers are
NULL, fix this by ignoring NULL pointers here.
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If AR_KeyMiss is set in the rx descriptor and AR_RxFrameOK is unset,
the hardware could not locate a valid key during a decryption attempt.

In this case, the frame must not be reported as decrypted, otherwise
mac80211 sees only random garbage.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>