Add pinctrl definitions for i2c1 and i2c2 busses on the Lager board
to ensure these are setup correctly at initialisation time. The i2c0
and i2c3 busses are connected to single function pins.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
[horms+renesas@verge.net.au: Added shmobile to patch title]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add i2c0, i2c1, i2c2 and i2c3 nodes to the Lager reference device tree as
these busses all have devices on them that can be probed even if they
are no drivers yet.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
[horms+renesas@verge.net.au: Added shmobile to title]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add needed information inside CPU0 for the generic cpufreq-cpu0 driver.

- voltage-tolerance = 1%
  It reflects the tolerance for the CPU voltage defined inside the OPP
  table. Due to the lack of proper OPP definition, use an arbitrary safe
  value.
- clock-latency = 300 us
  Approximate worst-case latency to do a full DVFS transition for every
  OPPs. Due to the lack of HW information, use an arbitrary safe value.
  Note: The term transition-latency will be more accurate to define this
  value since the clock transition latency is not the only parameter that
  will define the overall DVFS transition.
- operating-points = < kHz - uV >
  List of 6 operating points. All of them are using the same voltage
  since DVS is not supported in R-CAR Gen2.
- clocks
  phandle to the CPU clock source. This clock source is used for all the
  2 CortexA15 located inside the same cluster.
Signed-off-by: NGaku Inami <gaku.inami.xw@bp.renesas.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The CA15 cluster is capable of voltage scaling. Add the regulator
in the i2c6 node, to allow the generic CPUFreq driver to use it.

Enable the i2c6 pin mux and the device node as well since the
da9210 is connected to that bus.

Note: In R-CAR Gen2, each frequency is using the same voltage,
and DVS control is not used. Therefore, this patch set the
voltage(Vmin/Vmax) to 1000mv.
Signed-off-by: NGaku Inami <gaku.inami.xw@bp.renesas.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add needed information inside CPU0 for the generic cpufreq-cpu0 driver.

- voltage-tolerance = 1%
  It reflects the tolerance for the CPU voltage defined inside the OPP
  table. Due to the lack of proper OPP definition, use an arbitrary safe
  value.
- clock-latency = 300 us
  Approximate worst-case latency to do a full DVFS transition for every
  OPPs. Due to the lack of HW information, use an arbitrary safe value.
  Note: The term transition-latency will be more accurate to define this
  value since the clock transition latency is not the only parameter that
  will define the overall DVFS transition.
- operating-points = < kHz - uV >
  List of 6 operating points. All of them are using the same voltage
  since the valid Vmin voltage is not documented in the HW spec.
- clocks
  phandle to the CPU clock source. This clock source is used for all the
  4 CortexA15 located inside the same cluster.
Signed-off-by: NBenoit Cousson <bcousson+renesas@baylibre.com>
[gaku.inami.xw@bp.renesas.com: Change the setting of OPPs for ES2.0]
Signed-off-by: NGaku Inami <gaku.inami.xw@bp.renesas.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The CA15 cluster is capable of voltage scaling. Add the regulator
in the i2c3 node, to allow the generic CPUFreq driver to use it.

Enable the i2c3 pin mux and the device node as well since the
da9210 is connected to that bus.

Note: In R-CAR Gen2, each frequency is using the same voltage,
and DVS control is not used. Therefore, this patch set the
voltage(Vmin/Vmax) to 1000mv.
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>
[gaku.inami.xw@bp.renesas.com: Changes Vmin for disabling DVS]
Signed-off-by: NGaku Inami <gaku.inami.xw@bp.renesas.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add clocks for the SYS-DMAC0 and SYS-DMAC1 hardware blocks.

Cfr. the r8a7790 version by Ben Dooks.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

As early printk support is not enabled in the kernel in the
shmobile defconfig it does not make much sense to provide for
it in the default command line.
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

And make the node name numbering match the label numbering.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Cc: devicetree@vger.kernel.org
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

OMAP5432, DRA75x and DRA72x have MPU DPLLs that need Duty Cycle
Correction(DCC) to operate safely at frequencies >= 1.4GHz.

Switch to "ti,omap5-mpu-dpll-clock" compatible property which provides
this support.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>

Adds HDMI audio sDMA properties.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Adds HDMI audio sDMA properties.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add the necessary DTS nodes to enable the micro-HDMI output on Parlor
board.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Alto35 expansion board has a ZIF connector for a 3.5'' LCD.
Add a common include file for this configuration, and use it
on Alto35.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Chestnut43, Gallop43 and Palo43 expansion boards have a ZIF connector
for a 4.3'' LCD. Add a common include file for this configuration, and
use it on relevant expansion boards.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Summit and Tobi expansion boards have a HDMI connector with a TFP410
encoder. Add a common include file for this configuration, and then
use it for Summit and Tobi.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Looks like quite a few omap3 boards have sharp ls037v7dw01 that's
configured as various panel dpi entries for whatever legacy reasons.
For device tree based support, let's just configure these properly for
panel ls037v7dw01 instead of panel dpi.

This patch creates a common file for panel ls037v7dw01, and makes
boards ldp and omap3-evm to use it.

The ls037v7dw01 also seems to be coupled with an ad7846 touchscreen
controller for the omaps, so let's add a basic configuration for
the touchscreen also using the default values.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This patch add support for lcd display on gta04 board. Display control
is connected to spi (used spi bitbang driver).
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

omap5-uevm has a single HDMI output. Add the necessary display
information, including pinmuxing.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

omap5-uevm has a tca6424a I/O expander. Add it to the .dts file.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add OMAP5 DSS nodes to omap5.dtsi.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for am43x-epos-evm's LCD panel.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for am437x-gp-evm's LCD panel.
Signed-off-by: NSathya Prakash M R <sathyap@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add DT data for the display subsystem for AM4372. The DSS on AM4372 is
basically OMAP3's DSS, without DSI and VENC blocks.
Signed-off-by: NSathya Prakash M R <sathyap@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Arndale-Octa board is always configured to work with trustzone
firmware binary. Added DTS node entry to enable this support.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch add pmusysreg node for Exynos3250 to access PMU
(Power Management Unit) register in a centralized way using
syscon driver.
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The vbus-supply property is wrongly updated in the
usbdrd node instead of the usbdrd_phy node. This patch
fixes the same.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The vbus-supply property is wrongly updated in the
usbdrd node instead of the usbdrd_phy node. This patch
fixes the same.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add initial device tree nodes for EXYNOS5410 SoC and SMDK5410 board.
Signed-off-by: NTarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: NVyacheslav Tyrtov <v.tyrtov@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds new exynos3250.dtsi to support Exynos3250 SoC
based on Cortex-A7 dual core and includes following dt nodes:

- GIC interrupt controller
- Pinctrl to control GPIOs
- Clock controller
- CPU information (Cortex-A7 dual core)
- UART to support serial port
- MCT (Multi Core Timer)
- ADC (Analog Digital Converter)
- I2C/SPI bus
- Power domain
- PMU (Performance Monitoring Unit)
- MSHC (Mobile Storage Host Controller)
- PWM (Pluse Width Modulation)
- AMBA bus
- sysram node for SYSRAM memory mapping
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NHyunhee Kim <hyunhee.kim@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: devicetree@vger.kernel.org
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Adds the mfc node to exynos5800 which uses MFCv8.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add required fixed-regulator for VBUS supply for USB 3.0
controller phy.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Enable FIMD for peach-pi board.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Enable display controller with timing information for 1080p
panel in Exynos5800 peach-pi board.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Enable hdmi for peach-pi board.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Acked-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Adds support for google peach-pi board having the
Exynos5800 SoC.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Most of the nodes of exynos5420 remains same for exynos5800.
So the exynos5420.dtsi is included in exynos5800 and the changed
node properties will be overriden.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The patch adds the dts file for xyref5260 board which
is based on exynos5260 SoC.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>