Introduce a consistent style in vmlinux.lds.
This style is gradually being introduced for all archs.

A few lables were moved inside the section definition so
they are assigned the correct value of gcc decide to align
the content to another address than the one . has.
In the past this has fixed several bugs but for s390 it
will not impact due to all the alignmnet already introduced.

Stabs definitions are consolidated in asm-generic/vmlinux.lds.h
This patch also introduce support for DWARF - without knowing
if this makes sense for s390.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Constraint for err is wrong since it is preinitialized and the code
relies on it in case of an exception.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Currently there are situations, where the tape medium state (loaded, unloaded,
unknown) is not set correctly. The reason is that the medium association
field is used to determine the medium state. This not always leads to
correct results. To fix that we use another field of the medium sense
data instead.
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

After assigning values to specific registers memset was called. This
may clobber the contents of the used registers.
To solve this extract the two used inline assemblies into small
functions that don't call any functions.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Prevent that modules get loaded at addresses below 4GB to
prevent exchanging system call table entries.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

memcpy_real uses the mvcle instruction. This instruction alters all used
registers (source, destination and 2 x count). Therefore we have to flag
those registers as input/output registers (+d). In addition to that, we
have to specify, that we read from memory designated by "src" and write to
memory designated by "dest".
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

If we use the CLEAR ipl option, reipl is faster, since then VM can release
the memory, which has been paged out.
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Signed-off-by: NUrsula Braun <braunu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Replacing n & (n - 1) for power of 2 check by is_power_of_2(n)
Signed-off-by: Nvignesh babu <vignesh.babu@wipro.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

According to C99 6.3.2.3 it's undefined what happens if a converted
pointer is used to call a function whose type is not compatible with
the pointed-to type.
That's what the qdio code is doing, so fix it.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

slab cache debugging code has been changed so that we always get a
minimum alignment of the alignment of a 64-integer. Since this is
8 on s390/s390x there is no need of ARCH_KMALLOC_MINALIGN anymore.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

ext_int_info_t is no longer used in entry(64).S Instead do_extint is a C
function that handles the hash search.
As the structure is handled in C code, we can also remove the packed
attribute to avoid alignment issues. (Currently there is no alignment
problem in ext_int_info_t, even if packet)
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Also removes a bunch of ^L in drivers/s390/cio/cmf.c
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

There is no need to assign "0" to "hops" twice. Remove one assigment.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The termination condition of the loop that prints the operands of
an instruction doesn't stop after the maximum of 6 operands.
It continues with the operands of the next instruction format
instead which create really long lines.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

arch/s390/Kconfig tells us that CONFIG_APPLDATA_BASE is bool and hence can
never be built modular.  Given this, defining appldata_exit() function is
pointless (and wasteful, actually).  Remove all that.

Previous patch annotated appldata_offline_cpu() as __cpuexit, but now with the
__exit function appldata_exit() gone, the only callsite that references it is
__cpuinit, so this function can also be __cpuinit, thereby saving space when
HOTPLUG_CPU=n.
Signed-off-by: NSatyam Sharma <satyam@infradead.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

appldata_offline_cpu() is only called from __cpuinit-marked hotplug
notifier callback and from the __exit-marked module_exit function,
therefore candidate for __cpuexit.

BTW the __exit module_exit function appldata_exit() of this driver fails to
unregister_hotcpu_notifier() the notifier_block that was registered by
appldata_init() during module startup.  This will lead to oops if hotplug
notification comes after module has been unloaded.  Let's fix this by
unregistering the notifier appropriately (before appldata_offline_cpu()'ing
the CPUs).
Signed-off-by: NSatyam Sharma <satyam@infradead.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Symptom:     zcrypt fails by setting all PCIXCC/CEX2C cards offline for a
             certain type of invalid keys.
Problem:     zcrypt does not handle rc=12/rs=769 request responses correctly
Solution:    modify convert_type86_ica() to handle these error codes correctly
Signed-off-by: NRalph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Resetting of a all queues within a domain requires that a domain must
be selected first.
Signed-off-by: NRalph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NRalph Wuerthner <rwuerthn@de.ibm.com>

Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

There was the possibilty that an action like ccw_device_set_offline()
triggered by a device gone machine check might trigger a not oper
event. Unfortunately, this could lead to the situation that we tried
to unregister a subchannel twice: Once from the slow path evaluation,
and once via the not oper event.

Fix this by always using the same mechanism (css_schedule_eval()) for
triggering the unregister. This makes sure that unregistration will
only be done once. As an added bonus, it also simplyfies the code.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Don't forget to set dev->groups for early ccw devices like the
console device so the default attributes are created.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Disable channel measurements for all ccw devices via the ccw bus's
shutdown method. Clear residual cmf related information that may be
in the schib when setting up a new subchannel.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Introduce a shutdown method for the ccw bus that calls the driver
specific shutdown method in struct ccw_driver.
Switch zfcp to the new ccw_driver shutdown method.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Make sure channel path measurements are disabled via a reboot notifier
since we cannot rely on userspace to disable it again after enabling
it. This is 1. clean and 2. makes sure that channel path measurements
do not stay enabled after a reboot not involving a subsystem reset
(which would lead to the channel subsystem scribbling onto random
memory).
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

s390-drivers is generated using the docbook comments. It should
eventually supersede Documentation/s390/cds.txt.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Comment a bunch of function in docbook style and convert existing
comments on structures to docbook.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

- Fix existing kerneldoc-style comments.
- Move descriptions of functions from cmb.h to cmf.c.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Fix some formatting and correct a comment.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

subchannel_add_files() no longer exists, remove from header.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Rename css[] to channel_subsystems[] to avoid name clashes.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [ZLIB]: Fix external builds of zlib_inflate code.
  [TG3]: Fix APE induced regression
  [SKY2]: version 1.19
  [SKY2]: use netdevice stats struct
  [SKY2]: fiber advertise bits initialization (trivial)
  [SKY2]: fix power settings on Yukon XL
  [SKY2]: ethtool register reserved area blackout

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>