We are comparing policy->governor against cpufreq_gov_ondemand to make
sure that we update sampling rate only for the concerned CPUs. But that
isn't enough.

In case of governor_per_policy, there can be multiple instances of
ondemand governor and we will always end up updating all of them with
current code. What we rather need to do, is to compare dbs_data with
poilcy->governor_data, which will match only for the policies governed
by dbs_data.

This code is also racy as the governor might be getting stopped at that
time and we may end up scheduling work for a policy, which we have just
disabled.

Fix that by protecting the entire function with &od_dbs_cdata.mutex,
which will prevent against races with policy START/STOP/etc.

After these locks are in place, we can safely get the policy via per-cpu
dbs_info.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

For cpufreq drivers which use setpolicy interface, after offline->online
the policy is set to default. This can be reproduced by setting the
default policy of intel_pstate or longrun to ondemand and then change to
"performance". After offline and online, the setpolicy will be called with
the policy=ondemand.

For drivers using governors this condition is handled by storing
last_governor, during offline and restoring during online. The same should
be done for drivers using setpolicy interface. Storing last_policy during
offline and restoring during online.
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

If hardware-driven P-state selection (HWP) is enabled, the
"performance" mode of intel_pstate should only allow the processor
to use the highest-performance P-state available.  That is not
the case currently, so make it actually happen.
Acked-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NAlexandra Yates <alexandra.yates@linux.intel.com>
[ rjw: Subject and changelog ]
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The SCPI clk driver registers the virtual cpufreq device that kicks off
initialisation of the SCPI cpufreq driver. Also, clk_get() will fail for
the cpufreq driver if the SCPI clk driver is missing.

Fix this by making the SCPI cpufreq driver explicitly depend on the SCPI
clk driver.

Fixes: 8def3103 (cpufreq: arm_big_little: add SCPI interface driver)
Signed-off-by: NPunit Agrawal <punit.agrawal@arm.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

A rounding error was found in the calculation of limits->max_perf
in intel_pstate_set_policy(), which is used to calculate the max and min
pstate values in intel_pstate_get_min_max().  In that code,
limits->max_perf is truncated to 2 hex digits such that, for example,
0x169 was incorrectly calculated to 0x16 instead of 0x17.  This resulted in
the pstate being set one level too low.  This patch rounds the value of
limits->max_perf up instead of down so that the correct max pstate can
be reached.
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Acked-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

I have a Intel (6,63) processor with a "marketing" frequency (from
/proc/cpuinfo) of 2100MHz, and a max turbo frequency of 2600MHz.  I
can execute

cpupower frequency-set -g powersave --min 1200MHz --max 2100MHz

and the max_freq_pct is set to 80.  When adding load to the system I noticed
that the cpu frequency only reached 2000MHZ and not 2100MHz as expected.

This is because limits->max_policy_pct is calculated as 2100 * 100 /2600 = 80.7
and is rounded down to 80 when it should be rounded up to 81.  This patch
adds a DIV_ROUND_UP() which will return the correct value.
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Acked-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Subsys interface's ->remove_dev() is called when the cpufreq driver is
unregistering or the CPU is getting physically removed. We keep removing
the cpuX/cpufreq link for all CPUs except the last one, which is a
mistake as all CPUs contain a link now.

Because of this, one CPU from each policy will still contain a link (to
an already removed policyX directory), after the cpufreq driver is
unregistered.

Fix that by removing the link first and then only see if the policy is
required to be freed. That will make sure that no links are left out.

Fixes: 96bdda61 ("cpufreq: create cpu/cpufreq/policyX directories")
Reported-and-tested-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The CPU policy struct indicates the co-ordination type
for all CPUs of a common freq domain. Initialize it
correctly using the CPU specific data gathered from
CPPC ACPI lib via acpi_get_psd_map().

The PSD object is optional, so the cpu->shared_type
can also be 0. So instead of assuming any value other
than SW_ANY(0xFD) is unsupported, explictly check
if shared_type is SW_ALL and then bail.
Signed-off-by: NAshwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The recently added mt8173 cpufreq driver relies on the cpu topology
that is always present on ARM64 but optional on ARM32:

drivers/cpufreq/mt8173-cpufreq.c: In function 'mtk_cpufreq_init':
drivers/cpufreq/mt8173-cpufreq.c:441:30: error: 'cpu_topology' undeclared (first use in this function)
  cpumask_copy(policy->cpus, &cpu_topology[policy->cpu].core_sibling);

This refines the Kconfig dependencies so that we can still build on
ARM32, but only if COMPILE_TEST is selected and the CPU topology
code is present.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

There are two flavors of Atom cores to be supported by intel_pstate,
Silvermont and Airmont, so make the driver distinguish between them by
adding separate frequency tables.

Separate the CPU defaults params for each of them and match the CPU IDs
against them as appropriate.
Signed-off-by: NPhilippe Longepe <philippe.longepe@linux.intel.com>
Signed-off-by: NStephane Gasparini <stephane.gasparini@linux.intel.com>
Acked-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject and changelog ]
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Rename symbol and function names starting with "BYT" or "byt" to
start with "ATOM" or "atom", respectively, so as to make it clear
that they may apply to Atom in general and not just to Baytrail
(the goal is to support several Atoms architectures eventually).

This should not lead to any functional changes.
Signed-off-by: NPhilippe Longepe <philippe.longepe@linux.intel.com>
Signed-off-by: NStephane Gasparini <stephane.gasparini@linux.intel.com>
Acked-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw : Changelog ]
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Revert commit 37afb000 (cpufreq: intel_pstate: Use ACPI perf
configuration) that is reported to cause a regression to happen
on a system where invalid data are returned by the ACPI _PSS object.

Since that commit makes assumptions regarding the _PSS output
correctness that may turn out to be overly optimistic in general,
there is a concern that it may introduce regression on more
systems, so it's better to revert it now and we'll revisit the
underlying issue in the next cycle with a more robust solution.

Conflicts:
        drivers/cpufreq/intel_pstate.c

Fixes: 37afb000 (cpufreq: intel_pstate: Use ACPI perf configuration)
Reported-by: NBorislav Petkov <bp@alien8.de>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Revert commit 4ef45148 (cpufreq: intel_pstate: Avoid calculation for
max/min) as it depends on commit 37afb000 (cpufreq: intel_pstate: Use
ACPI perf configuration) that causes problems to happen and needs to be
reverted.

Conflicts:
	drivers/cpufreq/intel_pstate.c
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

It is wrong to use do_div() with 32-bit dividends (unsigned long is
32 bits on 32-bit architectures).
Signed-off-by: NNicolas Pitre <nico@linaro.org>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

gov_queue_work() acquires cpufreq_governor_lock to allow
cpufreq_governor_stop() to drain delayed work items possibly scheduled
on CPUs that share the policy with a CPU being taken offline.

However, the same goal may be achieved in a more straightforward way if
the policy pointer in the struct cpu_dbs_info matching the policy CPU is
reset upfront by cpufreq_governor_stop() under the timer_mutex belonging
to it and checked against NULL, under the same lock, at the beginning of
dbs_timer().

In that case every instance of dbs_timer() run for a struct cpu_dbs_info
sharing the policy pointer in question after cpufreq_governor_stop() has
started will notice that that pointer is NULL and bail out immediately
without queuing up any new work items.  In turn, gov_cancel_work()
called by cpufreq_governor_stop() before destroying timer_mutex will
wait for all of the delayed work items currently running on the CPUs
sharing the policy to drop the mutex, so it may be destroyed safely.

Make cpufreq_governor_stop() and dbs_timer() work as described and
modify gov_queue_work() so it does not acquire cpufreq_governor_lock any
more.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

When booting an HWP enabled system the kernel displays one "HWP enabled"
message for each cpu.  The messages are superfluous since HWP is globally
enabled across all CPUs. This patch also adds an informational message
when HWP is disabled via intel_pstate=no_hwp.
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Reviewed-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The check for correct frequency being set in bL_cpufreq_set_rate is
broken when the big.LITTLE switcher is active, for two reasons.

 1. The 'new_rate' variable gets overwritten before the test by the
 code calculating the frequency of the old cluster.

 2. The frequency returned by bL_cpufreq_get_rate will be the virtual
 frequency, not the actual one the intended version of new_rate contains.

This means the function always returns an error causing an endless
stream of: "cpufreq: __target_index: Failed to change cpu frequency: -5"

As the intent is to check for errors that clk_set_rate doesn't report
lets move the check to immediately after that and directly use
clk_get_rate, rather than the arm_big_little helpers which only confuse
matters. Also, update the comment to be hopefully clearer about the
purpose of the code.

Fixes: 0a95e630 (cpufreq: arm_big_little: check if the frequency is set correctly)
Signed-off-by: NJon Medhurst <tixy@linaro.org>
Acked-by: NSudeep Holla <sudeep.holla@arm.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: NMichael Turquette <mturquette@baylibre.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The sysfs policy directory is postfixed currently with the CPU number
for which the policy was created, which isn't necessarily the first CPU
in related_cpus mask.

To make it more consistent and predictable, lets postfix the policy with
the first cpu in related-cpus mask.
Suggested-by: NSaravana Kannan <skannan@codeaurora.org>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: NSaravana Kannan <skannan@codeaurora.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The cpufreq sysfs interface had been a bit inconsistent as one of the
CPUs for a policy had a real directory within its sysfs 'cpuX' directory
and all other CPUs had links to it. That also made the code a bit
complex as we need to take care of moving the sysfs directory if the CPU
containing the real directory is getting physically hot-unplugged.

Solve this by creating 'policyX' directories (per-policy) in
/sys/devices/system/cpu/cpufreq/ directory, where X is the CPU for which
the policy was first created.

This also removes the need of keeping kobj_cpu and we can remove it now.
Suggested-by: NSaravana Kannan <skannan@codeaurora.org>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: NSaravana Kannan <skannan@codeaurora.org>
Acked-by: is more of a general agreement from the person that he is
Reviewed-by: is a more strict tag and implies that the reviewer has
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

They don't do anything special now, remove the unnecessary wrapper.
Reviewed-by: NSaravana Kannan <skannan@codeaurora.org>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Later patches will need to create policy specific directories in
/sys/devices/system/cpu/cpufreq/ directory and so the cpufreq directory
wouldn't be ever empty.

And so no fun creating/destroying it on need basis anymore. Create it
once on system boot.
Reviewed-by: NSaravana Kannan <skannan@codeaurora.org>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

->related_cpus is empty at this point of time and copying ->cpus to it
or orring ->related_cpus with ->cpus would result in the same value. But
cpumask_copy makes it rather clear.
Reviewed-by: NSaravana Kannan <skannan@codeaurora.org>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

'timer_mutex' is required to sync work-handlers of policy->cpus.
update_sampling_rate() is just canceling the works and queuing them
again. This isn't protecting anything at all in update_sampling_rate()
and is not gonna be of any use.

Even if a work-handler is already running for a CPU,
cancel_delayed_work_sync() will wait for it to finish.

Drop these unnecessary locks.
Reviewed-by: NPreeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

On systems that initialize the intel_pstate driver with the performance
governor, and then switch to the powersave governor will not transition to
lower cpu frequencies until /sys/devices/system/cpu/intel_pstate/min_perf_pct
is set to a low value.

The behavior of governor switching changed after commit a0475992
("[cpufreq] intel_pstate: honor user space min_perf_pct override on
 resume").  The commit introduced tracking of performance percentage
changes via sysfs in order to restore userspace changes during
suspend/resume.  The problem occurs because the global values of the newly
introduced max_sysfs_pct and min_sysfs_pct are not lowered on the governor
change and this causes the powersave governor to inherit the performance
governor's settings.

A simple change would have been to reset max_sysfs_pct to 100 and
min_sysfs_pct to 0 on a governor change, which fixes the problem with
governor switching.  However, since we cannot break userspace[1] the fix
is now to give each governor its own limits storage area so that governor
specific changes are tracked.

I successfully tested this by booting with both the performance governor
and the powersave governor by default, and switching between the two
governors (while monitoring /sys/devices/system/cpu/intel_pstate/ values,
and looking at the output of cpupower frequency-info).  Suspend/Resume
testing was performed by Doug Smythies.

[1] Systems which suspend/resume using the unmaintained pm-utils package
will always transition to the performance governor before the suspend and
after the resume.  This means a system using the powersave governor will
go from powersave to performance, then suspend/resume, performance to
powersave.  The simple change during governor changes would have been
overwritten when the governor changed before and after the suspend/resume.
I have submitted https://bugzilla.redhat.com/show_bug.cgi?id=1271225
against Fedora to remove the 94cpufreq file that causes the problem.  It
should be noted that pm-utils is obsoleted with newer versions of systemd.
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Acked-by: NKristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This is a workaround for KNL platform, where in some cases MPERF counter
will not have updated value before next read of MSR_IA32_MPERF. In this
case divide by zero will occur. This change ignores current sample for
busy calculation in this case.

Fixes: b34ef932 (intel_pstate: Knights Landing support)
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: NKristen Carlson Accardi <kristen@linux.intel.com>
Cc: 4.1+ <stable@vger.kernel.org> # 4.1+
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

When requested from cpufreq to set policy, look into _pss and get
control values, instead of using max/min perf calculations. These
calculation misses next control state in boundary conditions.
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: NKristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Use ACPI _PSS to limit the Intel P State turbo, max and min ratios.
This driver uses acpi processor perf lib calls to register performance.
The following logic is used to adjust Intel P state driver limits:
- If there is no turbo entry in _PSS, then disable Intel P state turbo
and limit to non turbo max
- If the non turbo max ratio is more than _PSS max non turbo value, then
set the max non turbo ratio to _PSS non turbo max
- If the min ratio is less than _PSS min then change the min ratio
matching _PSS min
- Scale the _PSS turbo frequency to max turbo frequency based on control
value.
This feature can be disabled by using kernel parameters:
intel_pstate=no_acpi
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: NKristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Systems with configurable TDP have multiple max non turbo p state. Intel
P state uses max non turbo P state for scaling. But using the real max
non turbo p state causes underestimation of next P state. So using
the physical max non turbo P state as before for scaling.
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: NKristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

After Ivybridge, the max non turbo ratio obtained from platform info msr
is not always guaranteed P1 on client platforms. The max non turbo
activation ratio (TAR), determines the max for the current level of TDP.
The ratio in platform info is physical max. The TAR MSR can be locked,
so updating this value is not possible on all platforms.
This change gets this ratio from MSR TURBO_ACTIVATION_RATIO if
available,
but also do some sanity checking to make sure that this value is
correct.
The sanity check involves reading the TDP ratio for the current tdp
control value when platform has configurable TDP present and matching
TAC
with this.
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: NKristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

We just made sure policy->cpu is online and this check will always fail
as the policy is active. Drop it.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NSaravana Kannan <skannan@codeaurora.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This driver utilizes the methods introduced in a previous
patch titled - "ACPI: Introduce CPU performance controls using CPPC"
and enables usage with existing CPUFreq governors.
Signed-off-by: NAshwin Chaugule <ashwin.chaugule@linaro.org>
Reviewed-by: NAl Stone <al.stone@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

When scaling_available_frequencies is read on an offlined cpu, then
either lockup or junk values are displayed. This is caused by
freed freq_table, which policy is using.
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

When freqdomain_cpus attribute is read from an offlined cpu, it will
cause crash. This change prevents calling cpufreq_show_cpus when
policy driver_data is NULL.

Crash info:

[  170.814949] BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
[  170.814990] IP: [<ffffffff813b2490>] _find_next_bit.part.0+0x10/0x70
[  170.815021] PGD 227d30067 PUD 229e56067 PMD 0
[  170.815043] Oops: 0000 [#2] SMP
[  170.816022] CPU: 3 PID: 3121 Comm: cat Tainted: G      D    OE   4.3.0-rc3+ #33
...
...
[  170.816657] Call Trace:
[  170.816672]  [<ffffffff813b2505>] ? find_next_bit+0x15/0x20
[  170.816696]  [<ffffffff8160e47c>] cpufreq_show_cpus+0x5c/0xd0
[  170.816722]  [<ffffffffa031a409>] show_freqdomain_cpus+0x19/0x20 [acpi_cpufreq]
[  170.816749]  [<ffffffff8160e65b>] show+0x3b/0x60
[  170.816769]  [<ffffffff8129b31c>] sysfs_kf_seq_show+0xbc/0x130
[  170.816793]  [<ffffffff81299be3>] kernfs_seq_show+0x23/0x30
[  170.816816]  [<ffffffff81240f2c>] seq_read+0xec/0x390
[  170.816837]  [<ffffffff8129a64a>] kernfs_fop_read+0x10a/0x160
[  170.816861]  [<ffffffff8121d9b7>] __vfs_read+0x37/0x100
[  170.816883]  [<ffffffff813217c0>] ? security_file_permission+0xa0/0xc0
[  170.816909]  [<ffffffff8121e2e3>] vfs_read+0x83/0x130
[  170.816930]  [<ffffffff8121f035>] SyS_read+0x55/0xc0
...
...
[  170.817185] ---[ end trace bc6eadf82b2b965a ]---
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Cc: 4.2+ <stable@vger.kernel.org> # 4.2+
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control including CPU DVFS. SCPI Message Protocol is used to
communicate with the SCPI.

This patch adds a interface driver for adding OPPs and registering
the arm_big_little cpufreq driver for such systems.
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org

Log a 'critical' message if the max frequency is reduced below nominal
frequency. We already log 'info' message if the max frequency is
capped below turbo frequency. CPU should guarantee atleast nominal
frequency, but not turbo frequency in all system configurations and
environments. So report the pmax throttling with severity when Pmax is
dipped below nominal frequency.
Signed-off-by: NShilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

For i.MX6UL, the clock switch flow is slightly different from
other i.MX6 SOCs. It has a 'secondary_sel' clk that will be used
when the CPU freq is higher than 396MHz. So the clock switch flow in
'set_target' callback need to update to support i.MX6UL in the common
i.MX6 SOC cpufreq driver.
Signed-off-by: NBai Ping <b51503@freescale.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

CONFIG_PM ifdefs are superfluous and can be removed.
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Conservative governor has its own 'enable' field to check if
conservative governor is used for a CPU or not

This can be checked by policy->governor with 'cpufreq_gov_conservative'
and so this field can be dropped.

Because its not guaranteed that dbs_info->cdbs.shared will a valid
pointer for all CPUs (will be NULL for CPUs that don't use
ondemand/conservative governors), we can't use it anymore. Lets get
policy with cpufreq_cpu_get_raw() instead.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: NLuis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>