Required for WaEnablePreemptionGranularityControlByUMD:skl,bxt

This register is added to HW whitelist to support WA required for future
enabling of pre-emptive command execution, WA implementation will be in
userspace and it cannot program this register if it is not on HW whitelist.

v2: explain purpose of WA (Chris)
Reviewed-by: NNick Hoath <nicholas.hoath@intel.com>
Signed-off-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453412634-29238-3-git-send-email-arun.siluvery@linux.intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Some of the HW registers are privileged and cannot be written to from
non-privileged batch buffers coming from userspace unless they are added to
the HW whitelist. This whitelist is maintained by HW and it is different from
SW whitelist. Userspace need write access to them to implement preemption
related WA.

The reason for using this approach is, the register bits that control
preemption granularity at the HW level are not context save/restored; so even
if we set these bits always in kernel they are going to change once the
context is switched out.  We can consider making them non-privileged by
default but these registers also contain other chicken bits which should not
be allowed to be modified.

In the later revisions controlling bits are save/restored at context level but
in the existing revisions these are exported via other debug registers and
should be on the whitelist. This patch adds changes to provide HW with a list
of registers to be whitelisted. HW checks this list during execution and
provides access accordingly.

HW imposes a limit on the number of registers on whitelist and it is
per-engine.  At this point we are only enabling whitelist for RCS and we don't
foresee any requirement for other engines.

The registers to be whitelisted are added using generic workaround list
mechanism, even these are only enablers for userspace workarounds. But by
sharing this mechanism we get some test assets without additional cost (Mika).

v2: rebase

v3: parameterize RING_FORCE_TO_NONPRIV() as _MMIO() should be limited to
i915_reg.h (Ville), drop inline for wa_ring_whitelist_reg (Mika).

v4: improvements suggested by Chris Wilson.
Clarify that this is HW whitelist and different from the one maintained in
driver. This list is engine specific but it gets initialized along with other
WA which is RCS specific thing, so make it clear that we are not doing any
cross engine setup during initialization.
Make HW whitelist count of each engine available in debugfs.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453412634-29238-2-git-send-email-arun.siluvery@linux.intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Imre mentioned that chv might also have capability to
track unclaimed mmio accesses. Ville added that
both chv and vlv has this capability and he had already
made this way back [1]. Mimic what Ville's patch does
but adapt on top of less frequent mmio accesses by
omitting checking always on reg writes.

This patch is untested as of now.

v2: overflow handling and posting omitted (Ville)

References: [1] http://lists.freedesktop.org/archives/intel-gfx/2013-May/027599.html
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450201542-22918-1-git-send-email-mika.kuoppala@intel.com

DRM Docbook is now Markdown ready. This means its doc is able to
use markdown text on it.

* Documentation/DocBook/drm.tmpl: Contains a table duplicated from
  drivers/gpu/drm/i915/i915_reg.h. This is not needed anymore

* drivers/gpu/drm/drm_modeset_lock.c: had a code example that used
  to look pretty bad on html. Fixed by using proper code markup.

* drivers/gpu/drm/drm_prime.c: Remove spaces between lines to make
  a proper markup list.

* drivers/gpu/drm/i915/i915_reg.h: Altought pandoc supports tables,
  it doesn't support table cell spanning. But we can use fixed-width
  for those special cases.

* include/drm/drm_vma_manager.h: Another code example that should be
  proper indented with four spaces.

v2 (Daniel): Adjust name to gpu.xml due to rename.

v3 (Daniel):
Split out the actual enabling in the Makefile - this way we can merge
the conversion, while just keeping the enabling in a drm-private tree.

Signed-off-by: Danilo Cesar Lemes de Paula <danilo.cesar@collabora.co.uk> (v1)
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephan Mueller <smueller@chronox.de>
Cc: Michal Marek <mmarek@suse.cz>
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: intel-gfx <intel-gfx@lists.freedesktop.org>
Cc: dri-devel <dri-devel@lists.freedesktop.org>
Acked-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448471279-19748-2-git-send-email-daniel.vetter@ffwll.ch

Pipe is assigned based on the port, but it should be
based on current crtc. Correcting the same in this patch.

v2: Use macro BXT_PIPE_SELECT(pipe) (Daniel)
Signed-off-by: NDeepak M <m.deepak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When we want to use SPLL for FDI we want SSC, which means we have to
disable clock bending for the PCH SSC reference (bend and spread are
mutually exclusive). So let's turn off bending when we want spread.
In case the BIOS enabled clock bending for some reason we'll just turn
it off and enable the spread mode instead.

Not sure what happens if the BIOS is actually using the bend source for
HDMI at this time, but I suppose it should be no worse than what already
happens when we simply turn on the spread.

We don't currently use the bend source for anything, and only use the
PCH SSC reference for the SPLL to drive FDI (always with spread).

v2: Fix the %5 vs %10 fumble for SSCDITHPHASE (Paulo)
    Add 'WARN_ON(steps % 5 != 0)' sanity check (Paulo)
    Fix typos in commit message (Paulo)

Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449260379-14093-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>

The reference clock for BXT is 19.2 MHz not 19.5 MHz, updating the
correct value here.
Signed-off-by: NDeepak M <m.deepak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449238659-12473-2-git-send-email-m.deepak@intel.com

LPT-H has a strap bit for fused off CRT block. Check it to see if
we should register the CRT connector or not. Supposedly this also
forces the ADAP enable bit to 0, so the detection we added in
commit 6c03a6bd ("drm/i915: Don't register CRT connector when it's fused off")
should already catch it, but checking the fuse bit should at least
do no harm.

v2: Use HAS_PCH_LPT_H() (Paulo)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449005335-15192-1-git-send-email-ville.syrjala@linux.intel.com

Per bspec, "Backlight PWM may stop in the asserted state, causing
backlight to stay fully on. WA: Before disabling PWM, set CLKGATE_DIS_0
0x46530 bit 13 PWM1 Gating Dis (for PWM1) or bit 14 PWM2 Gating Dis (for
PWM2). The bits can remain set without harm." (There's no workaround
name for this.)

This fixes some Broxton backlight issues.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[Jani: cleanup & commit message]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448958232-26520-3-git-send-email-jani.nikula@intel.com

Make I915_READ and I915_WRITE more type safe by wrapping the register
offset in a struct. This should eliminate most of the fumbles we've had
with misplaced parens.

This only takes care of normal mmio registers. We could extend the idea
to other register types and define each with its own struct. That way
you wouldn't be able to accidentally pass the wrong thing to a specific
register access function.

The gpio_reg setup is probably the ugliest thing left. But I figure I'd
just leave it for now, and wait for some divine inspiration to strike
before making it nice.

As for the generated code, it's actually a bit better sometimes. Eg.
looking at i915_irq_handler(), we can see the following change:
  lea    0x70024(%rdx,%rax,1),%r9d
  mov    $0x1,%edx
- movslq %r9d,%r9
- mov    %r9,%rsi
- mov    %r9,-0x58(%rbp)
- callq  *0xd8(%rbx)
+ mov    %r9d,%esi
+ mov    %r9d,-0x48(%rbp)
 callq  *0xd8(%rbx)

So previously gcc thought the register offset might be signed and
decided to sign extend it, just in case. The rest appears to be
mostly just minor shuffling of instructions.

v2: i915_mmio_reg_{offset,equal,valid}() helpers added
    s/_REG/_MMIO/ in the register defines
    mo more switch statements left to worry about
    ring_emit stuff got sorted in a prep patch
    cmd parser, lrc context and w/a batch buildup also in prep patch
    vgpu stuff cleaned up and moved to a prep patch
    all other unrelated changes split out
v3: Rebased due to BXT DSI/BLC, MOCS, etc.
v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-29-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

The logical render context population has a bunch of raw ring register
offsets. Use the names we have for them, and in cases where we we don't,
give them names.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-23-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

Add defines for the upper halves of the registers used by the cmd
parser. Getting rid of the arithmetic with the register offset
will help in making registers type safe.

v2: s/_HI/_UDW/ (Chris)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1446839080-18732-1-git-send-email-ville.syrjala@linux.intel.com

Store the upper dword of the register offset in the whitelist as well.
This would allow it to read register where the two halves aren't sitting
right next to each other, and it'll make it easier to make register
access type safe.

While at it change the register offsets to u32 from u64. Our register
space isn't quite that big, yet :)

v2: Use ldw/udw as the suffixes, and add a note about
    64bit wide split regs (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446839021-18599-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

v2: Use for_each_ring() (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446725633-6419-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-15-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

Most of our register defines follow the convention that if there's a
need for the raw register offset, that one has an underscore sa a
prefix. The define (possibly parametrized) without the underscore is
the one people should normally use, since it will take into account
all the parameters and other potential offsets that are needed.

Fix up the few stragglers that don't follow this convention.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-14-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

Handle DC off as a power well where enabling the power well will prevent
the DMC to enter selected DC states (required around modesets and Aux
A). Disabling the power well will allow DC states again. For now the
highest DC state is DC6 for Skylake and DC5 for Broxton but will be
configurable for Skylake in a later patch.

v2: Check both DC5 and DC6 bits in power well enabled function (Ville)
v3:
- Remove unneeded DC_OFF case in skl_set_power_well() (Imre)
- Add PW2 dependency to DC_OFF (Imre)
v4: Put DC_OFF before PW2 in BXT power well array
Signed-off-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
[fixed line over 80 and parenthesis alignment checkpatch warns (imre)]
Link: http://patchwork.freedesktop.org/patch/msgid/1447687201-24759-1-git-send-email-patrik.jakobsson@linux.intel.com

v2: Add explanation of the fixed power well bits (Imre)
Signed-off-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447682467-6237-2-git-send-email-patrik.jakobsson@linux.intel.com

Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
[fix line over 80 chars checkpatch WARN in gen9_set_dc_state() (imre)]
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-8-git-send-email-imre.deak@intel.com

lookup_power_well() expects uniq power well IDs, but atm we have
uninitialized IDs which would clash with those power wells with a 0
ID. This wasn't a problem so far since nothing looked up such a power
well, but an upcoming patch will (Misc IO for SKL), so fix this up on
platforms where this matters.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-2-git-send-email-imre.deak@intel.com

Drop the EDP_PSR_BASE() thing, and just stick the PSR register offset
under dev_priv, like we for DSI and GPIO for example.

TODO: could probably move a bunch of this kind of stuff into the device
info instead...

v2: Drop the spurious whitespace change (Jani)
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-7-git-send-email-ville.syrjala@linux.intel.com

Currently we determine the location of the AUX registers in a confusing
way. First we assume the PCH registers are used always, but then we
override it for everything but HSW/BDW to use DP+0x10. Very confusing.

Let's just make it straightforward and simply add a few functions to
pick the right AUX_CTL based on the DP port.

To deal with VLV/CHV we'll include the display_mmio_offset into the
AUX register defines.

v2: Reorder patches (Chris)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-5-git-send-email-ville.syrjala@linux.intel.com

v2: Keep some MISSING_CASE() stuff (Jani)
    s/-1/-PIPE_B/ in the register macro
    Fix typo in patch subject
v3: Use PORT_B registers for invalid ports in g4x_aux_ctl_reg() (Jani)
v4: Reorder patches (Chris)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> (v3)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-4-git-send-email-ville.syrjala@linux.intel.com

The DP link frequency is 162MHz, not 160MHz. Rename the ILK eDP PLL
defines to match.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446146763-31821-11-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We check these to determine firmware loading status. Include
them to help to debug causes of firmware loading fails.

v2: Move all CSR specific registers to i915_reg.h (Ville)
v3: Rebase
v4: Rebase (RPM ref)
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446220487-32691-1-git-send-email-mika.kuoppala@intel.com
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

For bxt CSR firmware exposes a count of dc5 entries. Expose
it through debugs
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

The CSR firmware expose two counters, handy to check if we are indeed
entering DC5/DC6.

v2: Rebase
v3: Take RPM ref before reading (Imre)
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> (v1)
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446220412-32574-1-git-send-email-mika.kuoppala@intel.com
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

SWF18 is set if the display has been initialized by the pre-os. It also
gives what configuration is enabled on which pipe. In skl_sanitize_cdclk,
the DPLL sanity check can pass even if GOP/VBIOS is not loaded as BIOS
enables DPLL for integrated audio codec related programming.
So fisrt check if SWF18 is set and then follow through with other DPLL
and CDCLK verification. If not set then for sure we need to sanitize the
cdclock.

v2: Update the commit message for clarity (Siva)
v3: Correct the mask to check for bits[23:0] instead of only bits[16:0].
    Had missed checking for PIPE C altogether. Remaining are reserved (Siva)
v4: Use ILK_SWF macro for SWF register definitions. Taken from Ville's patch
    http://lists.freedesktop.org/archives/intel-gfx/2015-November/079480.html

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Acked-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446726932-14078-1-git-send-email-shobhit.kumar@intel.comSigned-off-by: NJani Nikula <jani.nikula@intel.com>

v2: Rebase due to SKL_DPLLx usage
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1442595836-23981-21-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Parametrize the SWF registers. This also fixes the register offsets,
which were mostly garbage in the old defines.

Also save/restore only as many SWF registers that each platform has.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The PIPE_FRMCOUNT_GM45 and PIPE_FLIPCOUNT_GM45 names have bothered me
for a long time. The work equally well for ELK and onwards, so let's
s/GM45/G4X/.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A few register mask defines were missing the '0x' from hex numbers. Or
at least I assume those were meant to be hex numbers. Put the '0x' in
place.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Always put parens around macro argument evaluations.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Keep using the same registers (PCH_*) instead of accidentally
    starting to use the other ones (BXT_*)2) (Jesse)
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Note that in Bspec you have to dig around in a section called
"Timestamp bases" and Bspec update request is filed.
Signed-off-by: NAnkitprasad Sharma <ankitprasad.r.sharma@intel.com>
Signed-off-by: NAkash Goel <akash.goel@intel.com>
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
[danvet: Add note about state of Bspec.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is required to support glDispatchComputeIndirect for gen7.
Signed-off-by: NJordan Justen <jordan.l.justen@intel.com>
Reviewed-by: NKristian Høgsberg <krh@bitplanet.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Latest VBT mentions which set of registers will be used for BLC,
as controller number field. Making use of this field in BXT
BLC implementation. Also, the registers are used in case control
pin indicates display DDI. Adding a check for this.
According to Bspec, BLC_PWM_*_2 uses the display utility pin for output.
To use backlight 2, enable the utility pin with mode = PWM
   v2: Jani's review comments
   addressed
       - Add a prefix _ to BXT BLC registers definitions.
       - Add "bxt only" comment for u8 controller
       - Remove control_pin check for DDI controller
       - Check for valid controller values
       - Set pipe bits in UTIL_PIN_CTL
       - Enable/Disable UTIL_PIN_CTL in enable/disable_backlight()
       - If BLC 2 is used, read active_low_pwm from UTIL_PIN polarity
   Satheesh's review comment addressed
       - If UTIL PIN is already enabled, BIOS would have programmed it. No
       need to disable and enable again.
   v3: Jani's review comments
       - add UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK
       - Disable UTIL_PIN if controller 1 is used
       - Mask out UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK before enabling
       UTIL_PIN
       - check valid controller value in intel_bios.c
       - add backlight.util_pin_active_low
       - disable util pin before enabling
   v4: Change for BXT-PO branch:
   Stubbed unwanted definition which was existing before
   because of DC6 patch.
   UTIL_PIN_MODE_PWM     (0x1b << 24)

v2: Fixed Jani's review comment.

v3: Split the backight PWM frequency programming into separate patch,
    in cases BIOS doesn't initializes it.

v4: Starting afresh and not modifying existing state for backlight, as
    per Jani's recommendation.

v5: Fixed Jani's review comment wrt util pin enable
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Signed-off-by: NSunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>