Ever since we use only cfg80211 for configuration,
there is no configuration that could be pending at
this point, cfg80211 will have the configuration
that is pending and apply it afterwards.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I suspect the compiler will do this optimisation
anyway, but it seems cleaner to move this into
the WEP switch case.

Also make rx_h_decrypt use a local variable for
the frame_control so that we don't need to reload
the hdr variable for this after linearizing.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's no sense in letting anything but internal
mac80211 functions set the initiator to anything
but WLAN_BACK_INITIATOR, since WLAN_BACK_RECIPIENT
is only valid when we have received a frame from
the peer, which we react to directly in mac80211.

The debugfs code I recently added got this wrong
as well.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some hardware allow extended filtering of ARP frames not intended for
the host. To perform such filtering, the hardware needs to know the current
IP address(es) of the host, bound to its interface.

Add support for ARP filtering to mac80211 by adding a new op to the driver
interface, allowing to configure the current IP addresses. This op is called
upon association with the currently configured address(es), and when
associated whenever the IP address(es) change.

This patch adds configuration of IPv4 addresses only, as IPv6 addresses don't
need ARP filtering.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The IBSS code has a bogus mod_timer(..., 0) call,
we shouldn't ever pass a constant value to the
function since any constant value could be in the
future or the past.

However, invoking the timer here is not necessary
at all, since we just finished scanning and just
need to have the IBSS code run again from the
workqueue later, so factor out the work starting
and use that instead.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When sending action frames, we want to verify
that we do that on the correct channel. However,
checking the channel type in addition can get in
the way, since the channel type could change on
the fly during an association, and it's not
useful to have the channel type anyway since it
has no effect on the transmission. Therefore,
make it optional to specify so that if wanted,
it can still be checked, but is not required.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NWalter Goldens <goldenstranger@yahoo.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't refuse HT20 channels on devices that don't support HT40.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

sparse correctly complains that
__ieee80211_get_channel_mode is not static.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix sta_info.h kernel-doc warnings:

Warning(net/mac80211/sta_info.h:164): No description found for parameter 'tid_active_rx[STA_TID_NUM]'
Warning(net/mac80211/sta_info.h:164): Excess struct/union/enum/typedef member 'tid_state_rx' description in 'sta_ampdu_mlme'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 03ceedea.

This patch was reported to cause a regression in which connectivity is
lost and cannot be reestablished after a suspend/resume cycle.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Specifying a valid channel type will get
goto out rather than continuing, due to
missing braces. This affects both remain
on channel and action frame TX commands.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since wdev can be NULL, check it before dereferencing it
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

signal_type is enum cfg80211_signal_type.

This fixes the gcc warning:

scan.c: In function `cfg80211_inform_bss':
scan.c:518:6: warning: comparison between `enum cfg80211_signal_type' and `enum nl80211_bss'
scan.c: In function `cfg80211_inform_bss_frame':
scan.c:574:6: warning: comparison between `enum cfg80211_signal_type' and `enum nl80211_bss'
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix some issues introduced in batch skb dequeuing for input_pkt_queue.
The primary issue it that the queue head must be incremented only
after a packet has been processed, that is only after
__netif_receive_skb has been called.  This is needed for the mechanism
to prevent OOO packet in RFS.  Also when flushing the input_pkt_queue
and process_queue, the process queue should be done first to prevent
OOO packets.

Because the input_pkt_queue has been effectively split into two queues,
the calculation of the tail ptr is no longer correct.  The correct value
would be head+input_pkt_queue->len+process_queue->len.  To avoid
this calculation we added an explict input_queue_tail in softnet_data.
The tail value is simply incremented when queuing to input_pkt_queue.
Signed-off-by: NTom Herbert <therbert@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When GRO produces fraglist entries, and the resulting skb hits
an interface that is incapable of TSO but capable of FRAGLIST,
we end up producing a bogus packet with gso_size non-zero.

This was reported in the field with older versions of KVM that
did not set the TSO bits on tuntap.

This patch fixes that.
Reported-by: NIgor Zhang <yugzhang@redhat.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This race was triggered by a 'conntrack -F' command running in parallel
to the insertion of a hash for a new connection. Losing this race led to
a dead conntrack entry effectively blocking traffic for a particular
connection until timeout or flushing the conntrack hashes again.
Now the check for an already dying connection is done inside the lock.
Signed-off-by: NJoerg Marx <joerg.marx@secunet.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

This patch ensures that all places that schedule the DAD timer
look at the address state in a safe manner before scheduling the
timer.  This ensures that we don't end up with pending timers
after deleting an address.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes use of the new POSTDAD state.  This prevents
a race between DAD completion and failure.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes use of the new state_lock to synchronise between
updates to the ifa state.  This fixes the issue where a remotely
triggered address deletion (through DAD failure) coincides with a
local administrative address deletion, causing certain actions to
be performed twice incorrectly.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces the boolean dead flag on inet6_ifaddr with
a state enum.  This allows us to roll back changes when deleting
an address according to whether DAD has completed or not.

This patch only adds the state field and does not change the logic.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix build when CONFIG_SYSFS is not enabled:
net/bridge/br_if.c:136: error: 'struct net_bridge_port' has no member named 'sysfs_name'

Note: dev->name == sysfs_name except when change name is in
progress, and we are protected from that by RTNL mutex.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes from net/ (but not any netfilter files)
all the unnecessary return; statements that precede the
last closing brace of void functions.

It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.

Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
  xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the user has a bad classification configuration, and gets a packet
that goes through too many steps. Chances are more packets will arrive,
and the message spew will overrun syslog because it is not rate limited.
And because it is not tagged with appropriate priority it can't not be screened.

Added the qdisc to the message to try and give some more context when
the message does arrive.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Put severity level on pfkey printk messages
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Serious oh sh*t messages converted to WARN().
Add KERN_NOTICE severity to the unknown policy type messages.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The previous patch encourage me to go look at all the messages in
the network scheduler and fix them. Many messages were missing
any severity level. Some serious ones that should never happen
were turned into WARN(), and the random noise messages that were
handled changed to pr_debug().
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use kzalloc rather than the combination of kmalloc and memset.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression x,size,flags;
statement S;
@@

-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
 if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 5fa782c2
  sctp: Fix skb_over_panic resulting from multiple invalid \
    parameter errors (CVE-2010-1173) (v4)

cause 'error cause' never be add the the ERROR chunk due to
some typo when check valid length in sctp_init_cause_fixed().
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Reviewed-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new netdev ops ndo_{set|get}_vf_port to allow setting of
port-profile on a netdev interface.  Extends netlink socket RTM_SETLINK/
RTM_GETLINK with two new sub msgs called IFLA_VF_PORTS and IFLA_PORT_SELF
(added to end of IFLA_cmd list).  These are both nested atrtibutes
using this layout:

              [IFLA_NUM_VF]
              [IFLA_VF_PORTS]
                      [IFLA_VF_PORT]
                              [IFLA_PORT_*], ...
                      [IFLA_VF_PORT]
                              [IFLA_PORT_*], ...
                      ...
              [IFLA_PORT_SELF]
                      [IFLA_PORT_*], ...

These attributes are design to be set and get symmetrically.  VF_PORTS
is a list of VF_PORTs, one for each VF, when dealing with an SR-IOV
device.  PORT_SELF is for the PF of the SR-IOV device, in case it wants
to also have a port-profile, or for the case where the VF==PF, like in
enic patch 2/2 of this patch set.

A port-profile is used to configure/enable the external switch virtual port
backing the netdev interface, not to configure the host-facing side of the
netdev.  A port-profile is an identifier known to the switch.  How port-
profiles are installed on the switch or how available port-profiles are
made know to the host is outside the scope of this patch.

There are two types of port-profiles specs in the netlink msg.  The first spec
is for 802.1Qbg (pre-)standard, VDP protocol.  The second spec is for devices
that run a similar protocol as VDP but in firmware, thus hiding the protocol
details.  In either case, the specs have much in common and makes sense to
define the netlink msg as the union of the two specs.  For example, both specs
have a notition of associating/deassociating a port-profile.  And both specs
require some information from the hypervisor manager, such as client port
instance ID.

The general flow is the port-profile is applied to a host netdev interface
using RTM_SETLINK, the receiver of the RTM_SETLINK msg communicates with the
switch, and the switch virtual port backing the host netdev interface is
configured/enabled based on the settings defined by the port-profile.  What
those settings comprise, and how those settings are managed is again
outside the scope of this patch, since this patch only deals with the
first step in the flow.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb rxhash should be cleared when a skb is handled by a tunnel before
being delivered again, so that correct packet steering can take place.

There are other cleanups and accounting that we can factorize in a new
helper, skb_tunnel_rx()
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 33ad798c (tcp: options clean up) introduced a problem
if MD5+SACK+timestamps were used in initial SYN message.

Some stacks (old linux for example) try to negotiate MD5+SACK+TSTAMP
sessions, but since 40 bytes of tcp options space are not enough to
store all the bits needed, we chose to disable timestamps in this case.

We send a SYN-ACK _without_ timestamp option, but socket has timestamps
enabled and all further outgoing messages contain a TS block, all with
the initial timestamp of the remote peer.

Fix is to really disable timestamps option for the whole session.
Reported-by: NBijay Singh <Bijay.Singh@guavus.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The duplicate address check code got broken in the conversion
to hlist (2.6.35).  The earlier patch did not fix the case where
two addresses match same hash value. Use two exit paths,
rather than depending on state of loop variables (from macro).

Based on earlier fix by Shan Wei.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Reviewed-by: NShan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When attaching filters to a class pointing to a class higher up in the
hierarchy, classification may enter an endless loop. Currently this is
prevented for filters that are already resolved, but not for filters
resolved at runtime.

Only allow filters to point downwards in the hierarchy, similar to what
CBQ does.
Reported-by: NPawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several netem users use TBF for rate control. But every time the parameters
of TBF are changed it destroys the child qdisc, requiring reconfigation.
Better to just keep child qdisc and just notify it of changed limit.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also added an explicit break; to avoid
a fallthrough in net/ipv4/tcp_input.c
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removes the BKL in x25 setsock and getsockopts.
Signed-off-by: NAndrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moves the x25 accept approve flag from char into bitfield.
Signed-off-by: NAndrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moves the x25 interrupt flag from char into bitfield.
Signed-off-by: NAndrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>