[Why]
Requirement from the spec - we shouldn't be potentially exiting out
early based on encryption status.

[How]
Drop the calls from HDCP1 and HDCP2 execution that exit out early
based on link encryption status.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why&How]
Add logs to verify ILR optimization behaviour on boot
Signed-off-by: NMichael Strauss <michael.strauss@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
While Link Training is being performed,
and the LTTPRs are in Non-LTTPR or LTTPR Transparent mode,
any DPCD registers besides those used for Link Training are not to be
accessed.

The spec defines the link training registers as DP_TRAINING_PATTERN_SET
(102h) to DP_TRAINING_LANE3_SET (106h), and DP_LANE0_1_STATUS (202h)
to DP_ADJUST_REQUEST_LANE2_3 (207h).

[HOW]
Move the current write to DPCD Address DP_LINK_TRAINING_PATTERN_SET out
of its conditional block.
Signed-off-by: NWesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
We should skip programming manual trigger on non-primary planes when MPO is
enabled.

[HOW]
Implement an explicit mechanism for skipping manual trigger programming
for planes that shouldn't cause the frame to end.
Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: NKrunoslav Kovac <Krunoslav.Kovac@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Previous change had been reverted since it caused hang.
Remake change to avoid defect.

[Why]
1. Driver use umachannelnumber to calculate watermarks for stutter.
In asymmetric memory config, the actual bandwidth is less than
dual-channel. The bandwidth should be the same as single-channel.
2. We found single rank dimm need additional delay time for stutter.

[How]
Get information from each DIMM. Treat memory config as a single-channel
for asymmetric memory in bandwidth calculating.
Add additional delay time for single rank dimm.

Fixes: b8720ed0 ("drm/amd/display: System black screen hangs on driver load")
Signed-off-by: NHugo Hu <hugo.hu@amd.com>
Reviewed-by: NSung Lee <Sung.Lee@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Found that dc_link_reallocate_mst_payload is not used anymore
in any of the use case scenario.

[How]
removed dc_link_reallocate_mst_payload function definition
and declaration.
Signed-off-by: NRobin Singh <robin.singh@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Primary feature use case is with eDP panels.

[How]
Fail seamless boot validation if display is not an eDP panel.
Signed-off-by: NAnthony Wang <anthony1.wang@amd.com>
Reviewed-by: NMartin Leung <Martin.Leung@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
the current implementation of hdcp2 rx id list validation does not
have handler/checker for invalid message status, e.g. HMAC, the V
parameter calculated from PSP not matching the V prime from Rx.

[how]
return a generic FAILURE for any message status not SUCCESS or
REVOKED.
Signed-off-by: NDingchen (David) Zhang <dingchen.zhang@amd.com>
Reviewed-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
currently we enforce to update hdcp display using TYPE0, but there
is case that connector CP type prop be TYPE1 instead of type0.

[how]
using the drm prop of CP type of the connector as input argument.
Signed-off-by: NDingchen (David) Zhang <dingchen.zhang@amd.com>
Reviewed-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why & How]
We want to immediately fail seamless boot validation if DSC is active,
as VBIOS currently does not support DSC timings. Add a check for
the relevant flag in dc_validate_seamless_boot_timing.
Signed-off-by: NAnthony Wang <anthony1.wang@amd.com>
Reviewed-by: NMartin Leung <Martin.Leung@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
During dsc enable, a divide by zero condition triggered the
kernel crash.

[how]
An IGT test, which enable the DSC, was crashing at the time of
restore the default dsc status, becaue of h_totals value
becoming 0. So add a check before divide condition. If h_total
is zero, gracefully ignore and set the default value.

kernel panic log:

	[  128.758827] divide error: 0000 [#1] PREEMPT SMP NOPTI
	[  128.762714] CPU: 5 PID: 4562 Comm: amd_dp_dsc Tainted: G        W         5.4.19-android-x86_64 #1
	[  128.769728] Hardware name: ADVANCED MICRO DEVICES, INC. Mauna/Mauna, BIOS WMN0B13N Nov 11 2020
	[  128.777695] RIP: 0010:hubp2_vready_at_or_After_vsync+0x37/0x7a [amdgpu]
	[  128.785707] Code: 80 02 00 00 48 89 f3 48 8b 7f 08 b ......
	[  128.805696] RSP: 0018:ffffad8f82d43628 EFLAGS: 00010246
	......
	[  128.857707] CR2: 00007106d8465000 CR3: 0000000426530000 CR4: 0000000000140ee0
	[  128.865695] Call Trace:
	[  128.869712] hubp3_setup+0x1f/0x7f [amdgpu]
	[  128.873705] dcn20_update_dchubp_dpp+0xc8/0x54a [amdgpu]
	[  128.877706] dcn20_program_front_end_for_ctx+0x31d/0x463 [amdgpu]
	[  128.885706] dc_commit_state+0x3d2/0x658 [amdgpu]
	[  128.889707] amdgpu_dm_atomic_commit_tail+0x4b3/0x1e7c [amdgpu]
	[  128.897699] ? dm_read_reg_func+0x41/0xb5 [amdgpu]
	[  128.901707] ? dm_read_reg_func+0x41/0xb5 [amdgpu]
	[  128.905706] ? __is_insn_slot_addr+0x43/0x48
	[  128.909706] ? fill_plane_buffer_attributes+0x29e/0x3dc [amdgpu]
	[  128.917705] ? dm_plane_helper_prepare_fb+0x255/0x284 [amdgpu]
	[  128.921700] ? usleep_range+0x7c/0x7c
	[  128.925705] ? preempt_count_sub+0xf/0x18
	[  128.929706] ? _raw_spin_unlock_irq+0x13/0x24
	[  128.933732] ? __wait_for_common+0x11e/0x18f
	[  128.937705] ? _raw_spin_unlock_irq+0x13/0x24
	[  128.941706] ? __wait_for_common+0x11e/0x18f
	[  128.945705] commit_tail+0x8b/0xd2 [drm_kms_helper]
	[  128.949707] drm_atomic_helper_commit+0xd8/0xf5 [drm_kms_helper]
	[  128.957706] amdgpu_dm_atomic_commit+0x337/0x360 [amdgpu]
	[  128.961705] ? drm_atomic_check_only+0x543/0x68d [drm]
	[  128.969705] ? drm_atomic_set_property+0x760/0x7af [drm]
	[  128.973704] ? drm_mode_atomic_ioctl+0x6f3/0x85a [drm]
	[  128.977705] drm_mode_atomic_ioctl+0x6f3/0x85a [drm]
	[  128.985705] ? drm_atomic_set_property+0x7af/0x7af [drm]
	[  128.989706] drm_ioctl_kernel+0x82/0xda [drm]
	[  128.993706] drm_ioctl+0x225/0x319 [drm]
	[  128.997707] ? drm_atomic_set_property+0x7af/0x7af [drm]
	[  129.001706] ? preempt_count_sub+0xf/0x18
	[  129.005713] amdgpu_drm_ioctl+0x4b/0x76 [amdgpu]
	[  129.009705] vfs_ioctl+0x1d/0x2a
	[  129.013705] do_vfs_ioctl+0x419/0x43d
	[  129.017707] ksys_ioctl+0x52/0x71
	[  129.021707] __x64_sys_ioctl+0x16/0x19
	[  129.025706] do_syscall_64+0x78/0x85
	[  129.029705] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: NRobin Singh <robin.singh@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Reviewed-by: NRobin Singh <Robin.Singh@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

dimgrey_cavefish has similar gc_10_3 ip with sienna_cichlid,
so follow its registers offset setting.
Signed-off-by: NJiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: NTao Zhou <tao.zhou1@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

resolve bug on aldebaran where gfx error counts will
print on driver load when there are no errors present
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: NJohn Clements <john.clements@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

because "sscanf(str, "retire_page")" always return 0, if application use
the raw data for error injection, it always wrongly falls into "op ==
3". Change to use strstr instead.
Signed-off-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

In aldebaran, driver only needs to harvest SDP
RdRspStatus, WrRspStatus and first parity error
on RdRsp data. Check error type before harvest
error information.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NStanley Yang <Stanley.Yang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

SDP RdRspStatus/WrRspStatus or first parity error on
RdRsp data can cause system fatal error in arcturus.
GPU will be freezed in such case.

Driver needs to harvest these error information before
reset the GPU. Check error type to avoid harvest normal
gcea/mmea information.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NStanley Yang <Stanley.Yang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The tmz functions are verified on renoir chips as well. So enable it by
default.
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Tested-by: NLang Yu <Lang.Yu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When gfx wdt was configured to fatal_disable, the
timeout period should be configured to 0x0 (timeout
disabled)
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NDennis Li <Dennis.Li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

In poison progogate mode, when driver receive the edc error interrupt
from SQ, driver should kill the process by pasid which is using the
poison data, and then trigger GPU reset.
Signed-off-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Kernel test robot throws below warning ->

smatch warnings:
drivers/gpu/drm/radeon/si.c:4514 si_vm_packet3_cp_dma_check() warn:
inconsistent indenting

Fixed the inconsistent indenting.
Reported-by: NAbaci Robot <abaci@linux.alibaba.com>
Signed-off-by: NYang Li <yang.lee@linux.alibaba.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We should return -EINVAL instead of success if the "limit" is too high.

Fixes: e098bc96 ("drm/amd/pm: optimize the power related source code layout")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

If the kmemdup() fails then this should return a negative error code
but it currently returns success

Fixes: b4a7db71 ("drm/amdgpu: add per device user friendly xgmi events for vega20")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The value of pipe_id and queue_id  are not used under certain
circumstances, so just delete.
Signed-off-by: NTian Tao <tiantao6@hisilicon.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Accept non-linear buffers which use a multi-planar format, as long
as they don't use DCC.

Tested on GFX9 with NV12.
Signed-off-by: NSimon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: NBas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch checks the return value of the function
dc_link_add_remote_sink before using it. This was causing
a crash during consecutive hotplugs of DP MST displays.

Cc: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NShashank Sharma <shashank.sharma@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This reverts commit 55fa622f.

The regression caused by the original patch has been
cleared, thus introduce back the change.
Signed-off-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Current list supports modifiers that have DCC_MAX_COMPRESSED_BLOCK
set to AMD_FMT_MOD_DCC_BLOCK_128B, while AMD_FMT_MOD_DCC_BLOCK_64B
is used instead by userspace.

[How]
Replace AMD_FMT_MOD_DCC_BLOCK_128B with AMD_FMT_MOD_DCC_BLOCK_64B
for modifiers with DCC supported.

Fixes: faa37f54 ("drm/amd/display: Expose modifiers")
Signed-off-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: NBas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Tested-by: NBas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch is to revise two names of  sensor values for vangogh.
New smu metrics table is supported by new pmfw
(from version 4.63.36.00 ), it includes two parts, one part is
the current smu metrics table data and the other part is the
average smu metrics table data. The hwmon will read the current gfxclk
and mclk from the current smu metrics table data.
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch is to remove the "set" function of pp_dpm_mclk for vangogh.
For vangogh, mclk bonds with fclk, they will lock each other
on the same perfomance level. But according to the smu message from pmfw,
only fclk is allowed to set value manually, so remove the unnecessary
code of "set" function for mclk.
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Acked-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

If we skipped loading MEC2 firmware separately
from MEC, then MEC2 will be running the same
firmware image. Copy the MEC version and feature
numbers into MEC2 version and feature numbers.
This is needed for things like GWS support, where
we rely on knowing what version of firmware is
running on MEC2. Leaving these MEC2 entries blank
breaks our ability to version-check enables and
workarounds.
Signed-off-by: NJoseph Greathouse <Joseph.Greathouse@amd.com>
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch is to add the callback to get the bootup values for renoir.
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NLijo Lazar <lijo.lazar@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch is to update the atomfirmware header for smu12.

v2: remove some unnecessary members
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NLijo Lazar <lijo.lazar@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

ROCm user mode has acquired VMs from DRM file descriptors for as long
as it supported the upstream KFD. Legacy code to support older versions
of ROCm is not needed any more.
Signed-off-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NPhilip Yang <Philip.Yang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Use iterator methods exposed by amdgpu_res_cursor.h in building SG_TABLE's for a VRAM BO

Extend current implementation of SG_TABLE construction method to
allow exportation of sub-buffers of a VRAM BO. This capability will
enable logical partitioning of a VRAM BO into multiple non-overlapping
sub-buffers. One example of this use case is to partition a VRAM BO
into two sub-buffers, one for SRC and another for DST.
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NRamesh Errabolu <Ramesh.Errabolu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add back the double-sscanf so that both decimal
and hexadecimal values could be read in, but this
time invert the scan so that hexadecimal format
with a leading 0x is tried first, and if that
fails, then try decimal format.

Also use a logical-AND instead of nesting double
if-conditional.

See commit "drm/amdgpu: Fix a bug for input with double sscanf"

Cc: Alexander Deucher <Alexander.Deucher@amd.com>
Cc: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: NLuben Tuikov <luben.tuikov@amd.com>
Reviewed-by: NJohn Clements <john.clements@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

add ASPM support on polaris
Signed-off-by: NKenneth Feng <kenneth.feng@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

enable ASPM on vega to save the power
without the performance hurt.
Signed-off-by: NKenneth Feng <kenneth.feng@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

enable ASPM on navi1x for the benifit of system power consumption
without performance hurt.
Signed-off-by: NKenneth Feng <kenneth.feng@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

No need to config GECC feature here for sriov
Leave the host drvier to do the configuration job.
Signed-off-by: NJack Zhang <Jack.Zhang1@amd.com>
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When GFXCLK range is updated in manual/determinism mode, show the
updated min/max clock range.
Signed-off-by: NLijo Lazar <lijo.lazar@amd.com>
Reviewed-by: NHarish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>