Improves packet rate of 1-byte UDP receives by up to 10%.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds a DSA driver for:

Vitesse VSC7385 SparX-G5 5-port Integrated Gigabit Ethernet Switch
Vitesse VSC7388 SparX-G8 8-port Integrated Gigabit Ethernet Switch
Vitesse VSC7395 SparX-G5e 5+1-port Integrated Gigabit Ethernet Switch
Vitesse VSC7398 SparX-G8e 8-port Integrated Gigabit Ethernet Switch

These switches have a built-in 8051 CPU and can download and execute
firmware in this CPU. They can also be configured to use an external
CPU handling the switch in a memory-mapped manner by connecting to
that external CPU's memory bus.

This driver (currently) only takes control of the switch chip over
SPI and configures it to route packages around when connected to a
CPU port. The chip has embedded PHYs and VLAN support so we model it
using DSA as a best fit so we can easily add VLAN support and maybe
later also exploit the internal frame header to get more direct
control over the switch.

The four built-in GPIO lines are exposed using a standard GPIO chip.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VSC7385, VSC7388, VSC7395 and VSC7398 are integrated
switch/router chips for 5+1 or 8-port switches/routers. When
managed directly by Linux using DSA we need to do a special
set-up "dance" on the PHY. Unfortunately these sequences
switches the PHY to undocumented pages named 2a30 and 52b6
and does undocumented things. It is described by these opaque
sequences also in the reference manual. This is a best
effort to integrate it anyways.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds ethtool -r|--negotiate operation support. It triggers special
control bit on FW interface causing FW to restart link negotiation.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NAnton Mikaev <amikaev@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Runtime change of pause frame configuration (rx/tx flow control)
via ethtool.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We now pass link drop status to FW on init/deinit. This is required
to inform FW that driver took/released a control on link.
FW then will manage its own state and device power profile based
on this information. To improve management we remove mpi_set
function which ambiguously took both state and speed parameters.

Deinit callback is now a part of FW ops, as it actually manages the FW.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implemented ring size setup, min/max validation and reconfiguration in
runtime.
Signed-off-by: NAnton Mikaev <amikaev@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add suffix UL to constant 1024 in order to give the compiler complete
information about the proper arithmetic to use. Notice that this
constant is used in a context that expects an expression of type
u64 (64 bits, unsigned) and  following expressions are currently
being evaluated using 32-bit arithmetic:

qopt->idleslope * 1024 * ptr
qopt->hicredit * 1024 * 8
qopt->locredit * 1024 * 8

Addresses-Coverity-ID: 1470246 ("Unintentional integer overflow")
Addresses-Coverity-ID: 1470248 ("Unintentional integer overflow")
Addresses-Coverity-ID: 1470249 ("Unintentional integer overflow")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If SGMII was selected in the DT then the device should
write the SGMII enable bit.

If SGMII is not selected in the DT then the SGMII bit
should be disabled.
Signed-off-by: NDan Murphy <dmurphy@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add INT_STAT3 interrupt setting and clearing
support.
Signed-off-by: NDan Murphy <dmurphy@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For consistency, prefix hnae_ should be modified to hnae3_.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reference to Documentation/DMA-API-HOWTO.txt,
Streaming DMA mappings which are usually mapped for one DMA transfer,
Network card DMA ring descriptors should use Consistent DMA mappings.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Give default option for HNS3_HCLGE and HNS3_ENET will be helpful,
while dependency HNS3 is set. Meanwhile, use "if HNS3" section
instead of all the "depends on HNS3".
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some members in struct hns3_enet_tqp_vector, struct hnae3_client
and struct hnae3_ae_algo are unused.
This patch removes them.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set complete in the first hclge_cmd_csq_done of hclge_cmd_send,
and check if complete later, unnecessary to do hclge_cmd_csq_done
again.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

csq is used as a ring buffer, the value of the desc will be replaced
in next use. This patch removes the unnecessary memset, and just
updates the next_to_clean.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove some redundant assignments.
desc->flag = cpu_to_le16(HCLGE_CMD_FLAG_NO_INTR | HCLGE_CMD_FLAG_IN)
has set bit HCLGE_CMD_FLAG_WR to zero, so does others.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are some useless type cast, print in hclge_cmd_send.
This patch removes them.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hclge_ring_to_dma_dir is unused anywhere.
This patch removes it.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTL8211C has an issue when operating in Gigabit slave mode, therefore
genphy driver can't be used. See also this U-boot change.
https://lists.denx.de/pipermail/u-boot/2016-March/249712.html

Add a PHY driver for this chip with the quirk to force Gigabit master
mode. As a note: This will make it impossible to connect two network
ports directly which both are driven by a RTl8211C.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When adding support for RTL8211 I forgot to update the mdio_device_id
table.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Fixes: d241d4aa ("net: phy: realtek: add support for RTL8211")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This hack (affecting the non-PCIe models only) was introduced in 2004
to deal with link negotiation failures in 1GBit mode. Based on a
comment in the r8169 vendor driver I assume the issue affects RTL8169sb
in combination with particular 1GBit switch models.

Resetting the PHY every 10s and hoping that one fine day we will make
it to establish the link seems to be very hacky to me. I'd say:
If 1GBit doesn't work reliably in a users environment then the user
should remove 1GBit from the advertised modes, e.g. by using
ethtool -s <if> advertise <10/100 modes>

If the issue affects one chip version only and that with most link
partners, then we could also think of removing 1GBit from the
advertised modes for this chip version in the driver.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When ptp clock is not available for a PF (e.g., higher PFs in NPAR mode),
get-tsinfo() callback should return the software timestamp capabilities
instead of returning the error.

Fixes: 4c55215c ("qede: Add driver support for PTP")
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the correct size value while copying chassis/port id values.

Fixes: 6ad8c632 ("qed: Add support for query/config dcbx.")
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default, driver sets the eswitch mode incorrectly as VEB (virtual
Ethernet bridging).
Need to set VEB eswitch mode only when sriov is enabled, and it should be
to set NONE by default. The patch incorporates this change.

Fixes: 0fefbfba ("qed*: Management firmware - notifications and defaults")
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Memory size is limited in the kdump kernel environment. Allocation of more
msix-vectors (or queues) consumes few tens of MBs of memory, which might
lead to the kdump kernel failure.
This patch adds changes to limit the number of MSI-X vectors in kdump
kernel to minimum required value (i.e., 2 per engine).

Fixes: fe56b9e6 ("qed: Add module with basic common support")
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After we change the ipvlan mode from l3 to l2, or vice versa, we only
reset IFF_NOARP flag, but don't flush the ARP table cache, which will
cause eth->h_dest to be equal to eth->h_source in ipvlan_xmit_mode_l2().
Then the message will not come out of host.

Here is the reproducer on local host:

ip link set eth1 up
ip addr add 192.168.1.1/24 dev eth1
ip link add link eth1 ipvlan1 type ipvlan mode l3

ip netns add net1
ip link set ipvlan1 netns net1
ip netns exec net1 ip link set ipvlan1 up
ip netns exec net1 ip addr add 192.168.2.1/24 dev ipvlan1

ip route add 192.168.2.0/24 via 192.168.1.2
ping 192.168.2.2 -c 2

ip netns exec net1 ip link set ipvlan1 type ipvlan mode l2
ping 192.168.2.2 -c 2

Add the same configuration on remote host. After we set the mode to l2,
we could find that the src/dst MAC addresses are the same on eth1:

21:26:06.648565 00:b7:13:ad:d3:05 > 00:b7:13:ad:d3:05, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 58356, offset 0, flags [DF], proto ICMP (1), length 84)
    192.168.2.1 > 192.168.2.2: ICMP echo request, id 22686, seq 1, length 64

Fix this by calling dev_change_flags(), which will call netdevice notifier
with flag change info.

v2:
a) As pointed out by Wang Cong, check return value for dev_change_flags() when
change dev flags.
b) As suggested by Stefano and Sabrina, move flags setting before l3mdev_ops.
So we don't need to redo ipvlan_{, un}register_nf_hook() again in err path.
Reported-by: NJianlin Shi <jishi@redhat.com>
Reviewed-by: NStefano Brivio <sbrivio@redhat.com>
Reviewed-by: NSabrina Dubroca <sd@queasysnail.net>
Fixes: 2ad7bf36 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: NHangbin Liu <liuhangbin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently if sa_idx is equal to NSIM_IPSEC_MAX_SA_COUNT then
an out-of-bounds read on ipsec->sa will occur. Fix the
incorrect bounds check by using >= rather than >.

Detected by CoverityScan, CID#1470226 ("Out-of-bounds-read")

Fixes: 7699353d ("netdevsim: add ipsec offload testing")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NShannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the addition of GRO for ESP, gro_receive can consume the skb and
return -EINPROGRESS. In that case, the lower layer GRO handler cannot
touch the skb anymore.

Commit 5f114163 ("net: Add a skb_gro_flush_final helper.") converted
some of the gro_receive handlers that can lead to ESP's gro_receive so
that they wouldn't access the skb when -EINPROGRESS is returned, but
missed other spots, mainly in tunneling protocols.

This patch finishes the conversion to using skb_gro_flush_final(), and
adds a new helper, skb_gro_flush_final_remcsum(), used in VXLAN and
GUE.

Fixes: 5f114163 ("net: Add a skb_gro_flush_final helper.")
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Reviewed-by: NStefano Brivio <sbrivio@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the NFP fw only supports L3/L4 hashing so rejects the offload of
filters that output to LAG ports implementing other hash algorithms. Team,
however, uses a BPF function for the hash that is not defined. To support
Team offload, accept hashes that are defined as 'unknown' (only Team
defines such hash types). In this case, use the NFP default of L3/L4
hashing for egress port selection.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extract the tos and the tunnel flags from the tunnel key and offload these
action fields. Only the checksum and tunnel key flags are implemented in
fw so reject offloads of other flags. The tunnel key flag is always
considered set in the fw so enforce that it is set in the rule. Note that
the compulsory setting of the tunnel key flag and optional setting of
checksum is inline with how tc currently generates ipv4 udp tunnel
actions.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously the ttl for ipv4 udp tunnels was set to the namespace default.
Modify this to attempt to extract the ttl from a full route lookup on the
tunnel destination. If this is not possible then resort to the default.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardware will automatically update csum in headers when a set action has
been performed. This means we could in the driver ignore the explicit
checksum action when performing a set action.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We used to leave bus-info in ethtool driver info empty for
representors in case multi-PCIe-to-single-host cards make
the association between PCIe device and NFP many to one.
It seems these attempts are futile, we need to link the
representors to one PCIe device in sysfs to get consistent
naming, plus devlink uses one PCIe as a handle, anyway.
The multi-PCIe-to-single-system support won't be clean,
if it ever comes.

Turns out some user space (RHEL tests) likes to read bus-info
so just populate it.

While at it remove unnecessary app NULL-check, representors
are spawned by an app, so it must exist.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use napi_consume_skb() in nfp_net_tx_complete() to get bulk free.
Pass 0 as budget for ctrl queue completion since it runs out of
a tasklet.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NFP NAPI handling will only complete the TXed packets when called
with budget of 0, implement ndo_poll_controller by scheduling NAPI
on all TX queues.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some platforms with broken ACPI tables we may not have access
to the Serial Number PCIe capability.  This capability is crucial
for us for switchdev operation as we use serial number as switch ID,
and for communication with management FW where interface ID is used.

If we can't determine the Serial Number we have to fail device probe.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After user changes the ring count statistics for deactivated
rings disappear from ethtool -S output.  This causes loss of
information to the user and means that ethtool stats may not
add up to interface stats.  Always expose counters from all
the rings.  Note that we allocate at most num_possible_cpus()
rings so number of rings should be reasonable.

The alternative of only listing stats for rings which were
ever in use could be confusing.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When doing device hotplug the sub channel must be async to avoid
deadlock issues because device is discovered in softirq context.

When doing changes to MTU and number of channels, the setup
must be synchronous to avoid races such as when MTU and device
settings are done in a single ip command.
Reported-by: NThomas Walker <Thomas.Walker@twosigma.com>
Fixes: 8195b139 ("hv_netvsc: fix deadlock on hotplug")
Fixes: 732e4985 ("netvsc: fix race on sub channel creation")
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>