Logic was:
if (mode0 && mode1)
else if (mode0)
else

Should be:
if (mode0 && mode1)
else if (mode0)
else if (mode1)

Otherwise we may end up calculating the priority regs with
unitialized values.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16492Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

On systems using kexec, the new kernel is booted straight from the old kernel, without any warning to the graphics driver. So the GPU is basically left as-is in a running state, however the CPU side is completly reset.

Without stating the saneness of anyone using kexec on live systems, we should at least try not to crash the GPU. This patch resets 3 registers to 0 that could cause bad things to happen to the running system.

This allows kexec to work on a Power6/RN50 system.
Signed-off-by: NDave Airlie <airlied@redhat.com>

We will need method of selecting encoder that should receive HDMI block. For
now we assign HDMI block to first enabled encoder. Hopefully there are not many
RS6x0 chips with two digital encoders.

[airlied: add RS740 checks as per Alex suggestion.]
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The asics in question have the following requirements with regard to
their gart setups:

1. The GART aperture size has to be in the form of 2^X bytes, where X is from 25 to 31
2. The GART aperture MC base has to be aligned to a boundary equal to the size of the
aperture.
3. The GART page table has to be aligned to the boundary equal to the size of the table.
4. The GART page table size is: table_entry_size * (aperture_size / page_size)
5. The GART page table has to be allocated in non-paged, non-cached, contiguous system
memory.

This patch takes care 2.  The rest should already be handled properly.

This fixes a regression noticed by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: NTorsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Some IGP systems specify the system memory clock in the Firmware
table rather than the IGP info table.  Check both and make sure
we have a value system memory clock value.

v2: make sure rs690_pm_info is called on rs780/rs880 as well.

fixes a regression since 07d4190327b02ab3aaad25a2d168f79d92e8f8c2.
Reported-by: NMarkus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Tested-by: NMarkus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fixes fdo bug 27529:
https://bugs.freedesktop.org/show_bug.cgi?id=27529

Reported-by: steckdenis@yahoo.fr
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Remove the drm_resource wrappers and directly use the
actual PCI and/or platform functions in their place.

[airlied: fixup nouveau properly to build]
Signed-off-by: NJordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: NMatt Turner <mattst88@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Separate dynpm and profile based power management methods.  You can select the pm method
  by echoing the selected method ("dynpm" or "profile") to power_method in sysfs.
- Expose basic 4 profile in profile method
  "default" - default clocks
  "auto" - select between low and high based on ac/dc state
  "low" - DC, low power mode
  "high" - AC, performance mode
  The current base profile is "default", but it should switched to "auto" once we've tested
  on more systems.  Switching the state is a matter of echoing the requested profile to
  power_profile in sysfs.  The lowest power states are selected automatically when dpms turns
  the monitors off in all states but default.
- Remove dynamic fence-based reclocking for the moment.  We can revisit this later once we
  have basic pm in.
- Move pm init/fini to modesetting path.  pm is tightly coupled with display state.  Make sure
  display side is initialized before pm.
- Add pm suspend/resume functions to make sure pm state is properly reinitialized on resume.
- Remove dynpm module option.  It's now selectable via sysfs.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Will be used by nouveau driver also in the near future.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This simplify and improve GPU reset for R1XX-R6XX hw, it's
not 100% reliable here are result:
- R1XX/R2XX works bunch of time in a row, sometimes it
  seems it can work indifinitly
- R3XX/R3XX the most unreliable one, sometimes you will be
  able to reset few times, sometimes not even once
- R5XX more reliable than previous hw, seems to work most
  of the times but once in a while it fails for no obvious
  reasons (same status than previous reset just no same
  happy ending)
- R6XX/R7XX are lot more reliable with this patch, still
  it seems that it can fail after a bunch (reset every
  2sec for 3hour bring down the GPU & computer)

This have been tested on various hw, for some odd reasons
i wasn't able to lockup RS480/RS690 (while they use to
love locking up).

Note that on R1XX-R5XX the cursor will disapear after
lockup haven't checked why, switch to console and back
to X will restore cursor.

Next step is to record the bogus command that leaded to
the lockup.

V2 Fix r6xx resume path to avoid reinitializing blit
module, use the gpu_lockup boolean to avoid entering
inifinite waiting loop on fence while reiniting the GPU
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Patch rename gpu_reset to asic_reset in prevision of having
gpu_reset doing more stuff than just basic asic reset.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Add module option to force the display priority
  0 = auto, 1 = normal, 2 = high
- Default to high on r3xx/r4xx/rv515 chips
  Fixes flickering problems during heavy acceleration
  due to underflow to the display controllers
- Fill in minimal support for RS600

v2 - update display priority when bandwidth is updated
so the user can change the parameter at runtime and it
will take affect on the next modeset.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Check that atom cmd and data tables are valid
before using them.

(v2)
- fix some whitespace errors noticed by Rafał Miłecki
- check a few more cases
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- rs780/880 were using the wrong bandwidth functions
- convert r1xx-r4xx to use the same pm sclk/mclk structs as
r5xx+
- move bandwidth setup to a common function
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Look up i2c bus in the power table and expose it.
You'll need to load a hwmon driver for any chips
on the bus, this patch just exposes the bus.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>

In essence this creates a home for all asic specific declarations in
radeon_asic.h
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This patch properly set visible VRAM and enforce any pinned buffer
to be into visible VRAM. We might later add a flag to release this
constraint for some newer hw more clever than previous.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Get rid of _location and use _start/_end also simplify the
computation of vram_start|end & gtt_start|end. For R1XX-R2XX
we place VRAM at the same address of PCI aperture, those GPU
shouldn't have much memory and seems to behave better when
setup that way. For R3XX and newer we place VRAM at 0. For
R6XX-R7XX AGP we place VRAM before or after AGP aperture this
might limit to limit the VRAM size but it's very unlikely.
For IGP we don't change the VRAM placement.

Tested on (compiz,quake3,suspend/resume):
PCI/PCIE:RV280,R420,RV515,RV570,RV610,RV710
AGP:RV100,RV280,R420,RV350,RV620(RPB*),RV730
IGP:RS480(RPB*),RS690,RS780(RPB*),RS880

RPB: resume previously broken

V2 correct commit message to reflect more accurately the bug
and move VRAM placement to 0 for most of the GPU to avoid
limiting VRAM.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

In suspend path we unmap the GART table while in cleaning up
path we will unbind buffer and thus try to write to unmapped
GART leading to oops. In order to avoid this we don't call the
suspend path in cleanup path. Cleanup path is clever enough
to desactive GPU like the suspend path is doing, thus this was
redondant.

Tested on: RV370, R420, RV515, RV570, RV610, RV770 (all PCIE)
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

R300 family will hard lockup if host path read cache flush is
done through MMIO to HOST_PATH_CNTL. But scheduling same flush
through ring seems harmless. This patch remove the hdp_flush
callback and add a flush after each fence emission which means
a flush after each IB schedule. Thus we should have same behavior
without the hard lockup.

Tested on R100,R200,R300,R400,R500,R600,R700 family.

V2: Adjust fence counts in r600_blit_prepare_copy()
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Reviewed-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This detects if the sideport memory is enabled and
if it is VRAM is evicted on suspend/resume.

This should fix s/r issues on some IGPs.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

On resume on my rv530 laptop surface cntl was left disabled, so
wierd stuff would happen with rendering to a tiled front buffer.

This checks if the surface regs are assigned to bos and reprograms
the surface registers on resume using the same path that clears
them all on init.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@linux.ie>

Don't remap vram to 0 on IGP chips.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

also fix up rs690 mem width.

should fix fdo bug 25408
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

The locking & protection of radeon object was somewhat messy.
This patch completely rework it to now use ttm reserve as a
protection for the radeon object structure member. It also
shrink down the various radeon object structure by removing
field which were redondant with the ttm information. Last it
converts few simple functions to inline which should with
performances.

airlied: rebase on top of r600 and other changes.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We really don't need to process every irq that comes in, we only
really want to do SW irq processing when we are actually waiting for
a fence to pass. I'm not 100% sure this is race free esp on non-MSI systems
so it needs some testing.
Signed-off-by: NDave Airlie <airlied@redhat.com>

If we find a GPU but we can't find its BIOS and it isn't posted,
then ignore it.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Avivo hw have vblank interrupt in different place, fixes
irq handling (especialy irq disabling while suspending or
shuting down the module).
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This remove old init path and allow code cleanup, now all hw
use the new init path, see top of radeon.h for description of
this.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Also cleanup register specific to RS690/RS740. Version 2 add
missing header file for register, remove unecessary call to AGP
function and fix an indentation bug.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Convert the rv515 asic support to new init path also add an explanation
in radeon.h about the new init path. There is also few cleanups
associated with this change (others asic calling rv515 helper
functions).
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@linux.ie>

GART static one time initialization was mixed up with GART
enabling/disabling which could happen several time for instance
during suspend/resume cycles. This patch splits all GART
handling into 4 differents function. gart_init is for one
time initialization, gart_deinit is called upon module unload
to free resources allocated by gart_init, gart_enable enable
the GART and is intented to be call after first initialization
and at each resume cycle or reset cycle. Finaly gart_disable
stop the GART and is intended to be call at suspend time or
when unloading the module.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This adds some rv350+ register for LTE/GTE discard,
and enables the rv515 two sided stencil register.
It also disables the DEPTHXY_OFFSET register which
can be used to workaround the CS checker.
Moves rs690 to proper place in rs600 and uses correct
table on rs600.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This ports rs690 to the safe reg tables and makes rs600 also
use the same table.
Signed-off-by: NDave Airlie <airlied@redhat.com>

rs690 is r3xx 3D engine with AVIVO modesetting so we need to allow
AVIVO register for vline synchronization. This add a specific table
to rs690 to handle that. Thanks to Marc (marvin24) for debugging
this and kudos to Andre (taiu1) for spotting the origin of the bugs.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If an rn50/r100/m6/m7 GPU has < 64MB RAM, i.e. 8/16/32, the
aperture used to calculate the MC_FB_LOCATION needs to be worked
out from the CONFIG_APER_SIZE register, and not the actual vram size.

TTM VRAM size was also being initialised wrong, use actual vram size
to initialise it.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fix bandwidth computation and crtc priority in memory controller
so that crtc memory request are fullfill in time to avoid display
artifact.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>