Plug in the bdw+ irq handling for PSR interrupts. bdw+ supports psr on
any transcoder in theory, though the we don't currenty enable PSR except
on the EDP transcoder.

v2: From DK
 * Rebased on drm-tip
v3: Switched author to Ville based on IRC discussion.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NJose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180403212420.25007-2-dhinakaran.pandiyan@intel.com

The definitions for the error register should be valid on bdw/skl too,
but there we haven't even enabled DE_MISC handling yet.

Somewhat confusing the the moved register offset on bdw is only for
the _CTL/_AUX register, and that _IIR/IMR stayed where they have been
on bdw.

v2: Fixes from Ville.

v3: From DK
 * Rebased on drm-tip
 * Removed BDW IIR bit definition, looks like an unintentional change that
should be in the following patch.

v4: From DK
 * Don't mask REG_WRITE.

References: bspec/11974 [SRD Interrupt Bit Definition DevHSW]
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NJose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405220023.9449-1-dhinakaran.pandiyan@intel.com

Currently, we rely on inspecting the hangcheck state from within the
i915_reset() routines to determine which engines were guilty of the
hang. This is problematic for cases where we want to run
i915_handle_error() and call i915_reset() independently of hangcheck.
Instead of relying on the indirect parameter passing, turn it into an
explicit parameter providing the set of stalled engines which then are
treated as guilty until proven innocent.

While we are removing the implicit stalled parameter, also make the
reason into an explicit parameter to i915_reset(). We still need a
back-channel for i915_handle_error() to hand over the task to the locked
waiter, but let's keep that its own channel rather than incriminate
another.

This leaves stalled/seqno as being private to hangcheck, with no more
nefarious snooping by reset, be it whole-device or per-engine. \o/

The only real issue now is that this makes it crystal clear that we
don't actually do any testing of hangcheck per se in
drv_selftest/live_hangcheck, merely of resets!
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180406220354.18911-2-chris@chris-wilson.co.uk

BSpec says:

"Second level interrupt events are stored in the GT INT DW. GT INT DW is
a double buffered structure. A snapshot of events is taken when SW reads
GT INT DW. From the time of read to the time of SW completely clearing
GT INT DW (to indicate end of service), all incoming interrupts are logged
in a secondary storage structure. this guarantees that the record of
interrupts SW is servicing will not change while under service".

We read GT INT DW in several places now:

- The IRQ handler (banks 0 and 1) where, hopefully, it is completely
  cleared (operation now covered with the irq lock).
- The 'reset' interrupts functions for RPS and GuC logs, where we clear
  the bit we are interested in and leave the others for the normal
  interrupt handler.
- The 'enable' interrupts functions for RPS and GuC logs, as a measure
  of precaution. Here we could relax a bit and don't check GT INT DW
  at all or, if we do, at least we should clear the offending bit
  (which is what this patch does).

Note that, if every bit is cleared on reading GT INT DW, the register
won't be locked. Also note that, according to the BSpec, GT INT DW
cannot be cleared without first servicing the Selector & Shared IIR
registers.

v2:
  - Remove some code duplication (Tvrtko)
  - Make sure GT_INTR_DW are protected by the irq spinlock, since it's a
    global resource (Tvrtko)

v3: Optimize the spinlock (Tvrtko)

v4: Rebase.
v5:
  - take spinlock on outer scope to please sparse (Mika)
  - use raw_reg accessors (Mika)
v6: omit the continue in looping banks (Michel)

Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: NOscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v4)
Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180406093237.14548-1-mika.kuoppala@linux.intel.com

Using the new hierarchical interrupt infrastructure.

v2: Rebase
v3: Rebase
v4: use class/instance handler (Mika)

Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NOscar Mateo <oscar.mateo@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405140052.10682-3-mika.kuoppala@linux.intel.com

Interrupt identity register we already read from hardware
contains engine class and instance fields. Leverage
these fields to find correct engine to handle the interrupt.

v3: rebase on top of rps intr
    use correct class / instance limits (Michel)
v4: split engine/other handling
v5: empty iir is not err (Daniele, Michel)
Suggested-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180406093145.14389-1-mika.kuoppala@linux.intel.com

Using engine->irq_posted for execlists, we are not always serialised by
the tasklet as we supposed. On the reset paths, the tasklet is disabled
and ignored. Instead, we manipulate the engine->irq_posted directly to
account for the reset, but if an interrupt fired before the reset and so
wrote to engine->irq_posted, that write may not be flushed from the
local CPU's cacheline until much later as the tasklet is already active
and so does not generate a mb(). To correctly serialise the interrupt
with reset, we need serialisation on the set_bit() itself.

And at last Mika can be happy.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
CC: Michel Thierry <michel.thierry@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NJeff McGee <jeff.mcgee@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322073533.5313-3-chris@chris-wilson.co.uk

Not all callers want the GPU error to handled in the same way, so expose
a control parameter. In the first instance, some callers do not want the
heavyweight error capture so add a bit to request the state to be
captured and saved.

v2: Pass msg down to i915_reset/i915_reset_engine so that we include the
reason for the reset in the dev_notice(), superseding the earlier option
to not print that notice.
v3: Stash the reason inside the i915->gpu_error to handover to the direct
reset from the blocking waiter.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320100449.1360-2-chris@chris-wilson.co.uk

For the convenience of userspace passing in an arbitrary reset mask,
remove unknown engines from the set of engines that are to be reset.
This means that we always follow a per-engine reset with a full-device
reset when userspace writes -1 into debugfs/i915_wedged.
Reported-by: NMichał Winiarski <michal.winiarski@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180316215001.12391-1-chris@chris-wilson.co.ukReviewed-by: NMichel Thierry <michel.thierry@intel.com>

To allow future code reuse. While here, fix comment style.

v2: Notifications are a separate thing - rename the handler (Sagar)
Suggested-by: NOscar Mateo <oscar.mateo@intel.com>
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: NMichał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308154707.21716-3-michal.winiarski@intel.com

Originally we were inlining gen8_cs_irq_handler() and so expected the
compiler to constant-fold away the irq_shift (so we had hardcoded it as
opposed to use engine->irq_shift). However, we dropped the inline given
the proliferation of gen8_cs_irq_handler()s. If we pull the shifting
of the iir into the caller, we can shrink the code still further:

add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-34 (-34)
Function                                     old     new   delta
gen8_cs_irq_handler                          123     118      -5
gen8_gt_irq_handler                          261     248     -13
gen11_irq_handler                            722     706     -16

v2: Drop gen11_cs_irq_handler now that it is a simple
stub around gen8_cs_irq_handler (Daniele)

References: 5d3d69d5 ("drm/i915: Stop inlining the execlists IRQ handler")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309010808.11921-1-chris@chris-wilson.co.uk

This will get rid of the following error:
[   74.730271] WARNING: CPU: 4 PID: 0 at drivers/gpu/drm/drm_vblank.c:614 drm_calc_vbltimestamp_from_scanoutpos+0x13e/0x2f0
[   74.730311] Modules linked in: vgem snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic i915 x86_pkg_temp_thermal intel_powerclamp coretemp snd_hda_intel crct10dif_pclmul snd_hda_codec crc32_pclmul snd_hwdep broadcom ghash_clmulni_intel snd_hda_core bcm_phy_lib snd_pcm tg3 lpc_ich mei_me mei prime_numbers
[   74.730353] CPU: 4 PID: 0 Comm: swapper/4 Tainted: G     U           4.16.0-rc2-CI-CI_DRM_3822+ #1
[   74.730355] Hardware name: Dell Inc. XPS 8300  /0Y2MRG, BIOS A06 10/17/2011
[   74.730359] RIP: 0010:drm_calc_vbltimestamp_from_scanoutpos+0x13e/0x2f0
[   74.730361] RSP: 0018:ffff88022fb03d10 EFLAGS: 00010086
[   74.730365] RAX: ffffffffa0291d20 RBX: ffff88021a180000 RCX: 0000000000000001
[   74.730367] RDX: ffffffff820e7db8 RSI: 0000000000000001 RDI: ffffffff82068cea
[   74.730369] RBP: ffff88022fb03d70 R08: 0000000000000000 R09: ffffffff815d26d0
[   74.730371] R10: 0000000000000000 R11: ffffffffa0161ca0 R12: 0000000000000001
[   74.730373] R13: ffff880212448008 R14: ffff880212448330 R15: 0000000000000000
[   74.730376] FS:  0000000000000000(0000) GS:ffff88022fb00000(0000) knlGS:0000000000000000
[   74.730378] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   74.730380] CR2: 000055edcbec9000 CR3: 0000000002210001 CR4: 00000000000606e0
[   74.730382] Call Trace:
[   74.730385]  <IRQ>
[   74.730397]  drm_get_last_vbltimestamp+0x36/0x50
[   74.730401]  drm_update_vblank_count+0x64/0x240
[   74.730409]  drm_crtc_accurate_vblank_count+0x41/0x90
[   74.730453]  display_pipe_crc_irq_handler+0x176/0x220 [i915]
[   74.730497]  i9xx_pipe_crc_irq_handler+0xfe/0x150 [i915]
[   74.730537]  ironlake_irq_handler+0x618/0xa30 [i915]
[   74.730548]  __handle_irq_event_percpu+0x3c/0x340
[   74.730556]  handle_irq_event_percpu+0x1b/0x50
[   74.730561]  handle_irq_event+0x2f/0x50
[   74.730566]  handle_edge_irq+0xe4/0x1b0
[   74.730572]  handle_irq+0x11/0x20
[   74.730576]  do_IRQ+0x5e/0x120
[   74.730584]  common_interrupt+0x84/0x84
[   74.730586]  </IRQ>
[   74.730591] RIP: 0010:cpuidle_enter_state+0xaa/0x350
[   74.730593] RSP: 0018:ffffc9000008beb8 EFLAGS: 00000212 ORIG_RAX: ffffffffffffffde
[   74.730597] RAX: ffff880226b80040 RBX: 000000000031fc3e RCX: 0000000000000001
[   74.730599] RDX: 0000000000000000 RSI: ffffffff8210fb59 RDI: ffffffff820c02e7
[   74.730601] RBP: 0000000000000004 R08: 00000000000040af R09: 0000000000000018
[   74.730603] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000004
[   74.730606] R13: ffffe8ffffd00430 R14: 0000001166120bf4 R15: ffffffff82294460
[   74.730621]  ? cpuidle_enter_state+0xa6/0x350
[   74.730629]  do_idle+0x188/0x1d0
[   74.730636]  cpu_startup_entry+0x14/0x20
[   74.730641]  start_secondary+0x129/0x160
[   74.730646]  secondary_startup_64+0xa5/0xb0
[   74.730660] Code: e1 48 c7 c2 b8 7d 0e 82 be 01 00 00 00 48 c7 c7 ea 8c 06 82 e8 64 ec ff ff 48 8b 83 c8 07 00 00 48 83 78 28 00 0f 84 e2 fe ff ff <0f> 0b 45 31 ed e9 db fe ff ff 41 b8 d3 4d 62 10 89 c8 6a 03 41
[   74.730754] ---[ end trace 14b1345705b68565 ]---

Changes since v1:
- Don't try to apply CRC workaround when enabling pipe, it should already be enabled.
Changes since v2:
- Make crc functions for !DEBUGFS case inline.
- Pass intel_crtc to crc functions.
- Add comments to callsites.
Changes since v3:
- Cache selected source to pipe_crc->source.
- Set pipe_crc->skipped to MIN_INT during disable to close a race condition.
Changes since v4:
- Handle fallout from setting pipe_crc->source in irq handler.

Cc: Marta Löfstedt <marta.lofstedt@intel.com>
Reported-by: NMarta Löfstedt <marta.lofstedt@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105185Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308120202.52446-1-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

After we call dma_fence_signal(), confirm that the request was indeed
complete.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305104105.8296-1-chris@chris-wilson.co.uk

v2: Rebase.

v3:
  * Remove DPF, it has been removed from SKL+.
  * Fix -internal rebase wrt. execlists interrupt handling.

v4: Rebase.

v5:
  * Updated for POR changes. (Daniele Ceraolo Spurio)
  * Merged with irq handling fixes by Daniele Ceraolo Spurio:
      * Simplify the code by using gen8_cs_irq_handler.
      * Fix interrupt handling for the upstream kernel.

v6:
  * Remove early bringup debug messages (Tvrtko)
  * Add NB about arbitrary spin wait timeout (Tvrtko)

v7 (from Paulo):
  * Don't try to write RO bits to registers.
  * Don't check for PCH types that don't exist. PCH interrupts are not
    here yet.

v9:
  * squashed in selector and shared register handling (Daniele)
  * skip writing of irq if data is not valid (Daniele)
  * use time_after32 (Chris)
  * use I915_MAX_VCS and I915_MAX_VECS (Daniele)
  * remove fake pm interrupt handling for later patch (Mika)

v10:
  * Direct processing of banks. clear banks early (Chris)
  * remove poll on valid bit, only clear valid bit (Mika)
  * use raw accessors, better naming (Chris)

v11:
  * adapt to raw_reg_[read|write]
  * bring back polling the valid bit (Daniele)

v12:
  * continue if unset intr_dw (Daniele)
  * comment the usage of gen8_de_irq_handler bits (Daniele)

Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: NOscar Mateo <oscar.mateo@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180228101153.7224-2-mika.kuoppala@linux.intel.com

We want to de-emphasize the link between the request (dependency,
execution and fence tracking) from GEM and so rename the struct from
drm_i915_gem_request to i915_request. That is we may implement the GEM
user interface on top of requests, but they are an abstraction for
tracking execution rather than an implementation detail of GEM. (Since
they are not tied to HW, we keep the i915 prefix as opposed to intel.)

In short, the spatch:
@@

@@
- struct drm_i915_gem_request
+ struct i915_request

A corollary to contracting the type name, we also harmonise on using
'rq' shorthand for local variables where space if of the essence and
repetition makes 'request' unwieldy. For globals and struct members,
'request' is still much preferred for its clarity.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221095636.6649-1-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

The compiler is not automatically caching the i915->regs address inside
a register and emitting a load for every mmio access. For simple
functions like gen8_gt_irq_handler that are already using the raw
accessors, we can open-code them for substantial savings:

add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-83 (-83)
Function                                     old     new   delta
gen8_gt_irq_handler                          290     266     -24
gen8_gt_irq_ack                              181     122     -59
Total: Before=954637, After=954554, chg -0.01%

v2: Add raw_reg_read/raw_reg_write.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180219100926.16554-1-chris@chris-wilson.co.uk

Keep the master iir and use it to reduce the number of reads and writes
to the GT iir array, i.e. only the bits marked as set by the master iir
are valid inside GT iir array and will be handled during the interrupt.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180215073713.26985-1-chris@chris-wilson.co.uk

The frame counter may have got reset between disabling and enabling vblank
interrupts due to DMC putting the hardware to DC5/6 states if PSR was
active. The frame counter could also have stalled if PSR was active in case
there was no DMC. The frame counter resetting has a user visible impact
of screen freezes.

Make use of drm_vblank_restore() to compute missed vblanks for the duration
in which vblank interrupts were disabled and update the vblank counter with
this value as diff. There's no need to check if PSR was actually active in
the interrupt disabled duration, so simplify the check to a feature check.

Enabling vblank interrupts wakes up the hardware from DC5/6 and prevents it
from going back again as long as the there are pending interrupts. So, we
don't have to explicity disallow DC5/6 after enabling vblank interrupts to
keep the counter running.

This change is not applicable to CHV, as enabling interrupts does not
prevent the hardware from activating PSR.

v2: Added comments(Rodrigo) and rewrote commit message.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-10-dhinakaran.pandiyan@intel.com

As we ourselves cancel interrupts during reset by clearing the GTIIR, it
is possible for the master IIR to indicate a pending IRQ for which we
have already cleared from the GTIIR. In this case, the DRM_ERROR are
intended and should not be flagged as an error.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180202153448.23908-1-chris@chris-wilson.co.uk

On CNP boards that are using DDI F,
bit 25 (SDE_PORTE_HOTPLUG_SPT) is representing
the Digital Port F hotplug line when the Digital
Port F hotplug detect input is enabled.

v2: Reuse all existent structure instead of adding a
new HPD_PORT_F pointing to pin of port E.
v3: Use IS_CNL_WITH_PORT_F so we can start upstreaming
    this right now. If that SKU ever get a proper name
    we come back and update it.
v4: Rebase on top of digital connected port using encoder
    instead of port.
v5: Moved IS_CNL_WITH_PORT_F definition to the PCI IDs patch.

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-8-rodrigo.vivi@intel.com

On some Cannonlake SKUs we have a dedicated Aux for port F,
that is only the full split between port A and port E.

There is still no Aux E for Port E, as in previous platforms,
because port_E still means shared lanes with port A.

v2: Rebase.
v3: Add couple missed PORT_F cases on intel_dp.
v4: Rebase and fix commit message.
v5: Squash Imre's "drm/i915: Add missing AUX_F power well string"
v6: Rebase on top of display headers rework.
v7: s/IS_CANNONLAKE/IS_CNL_WITH_PORT_F (DK)
v8: Fix Aux bits for Port F (DK)
v9: Fix VBT definition of Port F (DK).
v10: Squash power well addition to this patch to avoid
     warns as pointed by DK.
v11: Clean up squashed commit message. (David)
v12: Remove unnecessary handling for older platforms (DK)
     Adding AUX_F to PG2 following other existent ones. (DK)

Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-2-rodrigo.vivi@intel.com

Disabling GuC interrupts involves access to GuC IRQ control registers
hence ensure device is RPM awake.

v1-v2: old changelog
1: Add comment about need to synchronize flush work and log runtime
   destroy
2: Moved patch earlier in the series and removed comment about future
work. (Tvrtko)

v3: Added assert_rpm_wakelock_held() to gen9_*_guc_interrupts. (Chris)
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1516808821-3638-1-git-send-email-sagar.a.kamble@intel.com

In the upcoming patch we will change the way how to recognize
when GuC is in use. Using helper macros will minimize scope
of that changes. While here, update dev_info message.
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171206135316.32556-3-michal.wajdeczko@intel.com

drivers/gpu/drm/i915/i915_irq.c|3096 col 29| error: comparison between signed and unsigned integer expressions [-Werror=sign-compare]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171130125253.21405-1-chris@chris-wilson.co.ukReviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>

intel_lrc_irq_handler and i915_guc_irq_handler are HW submission related
tasklet functions. Name them with "submission_tasklet" suffix and
remove intel/i915 prefix as they are static. Also rename irq_tasklet
as just tasklet for clarity.

v2: s/_bh/_tasklet (Chris)
Suggested-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1510839162-25197-2-git-send-email-sagar.a.kamble@intel.comSigned-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Back in commit a4b2b015 ("drm/i915: Don't mark an execlists
context-switch when idle") we noticed the presence of late
context-switch interrupts. We were able to filter those out by looking
at whether the ELSP remained active, but in commit beecec90
("drm/i915/execlists: Preemption!") that became problematic as we now
anticipate receiving a context-switch event for preemption while ELSP
may be empty. To restore the spurious interrupt suppression, add a
counter for the expected number of pending context-switches and skip if
we do not need to handle this interrupt to make forward progress.

v2: Don't forget to switch on for preempt.
v3: Reduce the counter to a on/off boolean tracker. Declare the HW as
active when we first submit, and idle after the final completion event
(with which we confirm the HW says it is idle), and track each source
of activity separately. With a finite number of sources, it should aide
us in debugging which gets stuck.

Fixes: beecec90 ("drm/i915/execlists: Preemption!")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023213237.26536-3-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
(cherry picked from commit 4a118ecb)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

The execlists emulation on top of the GuC (used for scheduling and
preemption) depends on the MI_USER_INTERRUPT for its notifications and
tasklet action. As we always employ the irq, there is no advantage in
ever disabling it while we are using the GuC, so allow us to arm the
breadcrumb irq when enabling GuC submission and disarm upon disabling.
The impact should be lessened by the delayed irq disabling we do (we
only disable after receiving an interrupt for which no one was wanting),
but allowing guc to explicitly manage the irq in relation to itself is
simpler and prevents an issue with losing an interrupt for preemption
as it is not coupled to an active request.

Internally, we add a reference counter (breadcrumbs.irq_enabled) as a
simple mechanism to allow GuC to keep the breadcrumb irq enabled. To
improve upon always enabling the irq while guc is selected, we need
to hook into the parking facility of intel_engines so that we only enable
the breadcrumbs while the GT is active (one step better would be to
individually park/unpark each engine).

In effect, this means that we keep the breadcrumb irq always enabled for
the entire duration the guc is busy, whereas before we would try to
switch it off whenever we idled for more than interrupt with no
associated waiters. The difference *should* be negligible in practice!

v2: Stop abusing fence signaling (and its auxiliary data structures) to
enable the breadcrumbs irqs.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>,
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>,
Link: https://patchwork.freedesktop.org/patch/msgid/20171025143943.7661-3-chris@chris-wilson.co.uk

Back in commit a4b2b015 ("drm/i915: Don't mark an execlists
context-switch when idle") we noticed the presence of late
context-switch interrupts. We were able to filter those out by looking
at whether the ELSP remained active, but in commit beecec90
("drm/i915/execlists: Preemption!") that became problematic as we now
anticipate receiving a context-switch event for preemption while ELSP
may be empty. To restore the spurious interrupt suppression, add a
counter for the expected number of pending context-switches and skip if
we do not need to handle this interrupt to make forward progress.

v2: Don't forget to switch on for preempt.
v3: Reduce the counter to a on/off boolean tracker. Declare the HW as
active when we first submit, and idle after the final completion event
(with which we confirm the HW says it is idle), and track each source
of activity separately. With a finite number of sources, it should aide
us in debugging which gets stuck.

Fixes: beecec90 ("drm/i915/execlists: Preemption!")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023213237.26536-3-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>

Prepared substructure rps for RPS related state. autoenable_work is
used for RC6 too hence it is defined outside rps structure. As we do
this lot many functions are refactored to use intel_rps *rps to access
rps related members. Hence renamed intel_rps_client pointer variables
to rps_client in various functions.

v2: Rebase.

v3: s/pm/gt_pm (Chris)
Refactored access to rps structure by declaring struct intel_rps * in
many functions.
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com> #1
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-9-git-send-email-sagar.a.kamble@intel.comAcked-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-8-chris@chris-wilson.co.uk

In order to separate GT PM related functionality into new structure
we are updating rps structure. hw_lock in it is used for display
related PCU communication too hence move it to dev_priv.
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-8-git-send-email-sagar.a.kamble@intel.comAcked-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-7-chris@chris-wilson.co.uk

We were using dev_priv->pm for runtime power management related state.
This patch renames it to "runtime_pm" which looks more apt.

v2: s/rpm/runtime_pm (Chris)
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com> #1Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-7-git-send-email-sagar.a.kamble@intel.comAcked-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-6-chris@chris-wilson.co.uk

Cleanup and parametrize the handling of South Error Interrupts (SERR_INT).
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507630626-23806-6-git-send-email-mika.kahola@intel.com

Fold IRQ pipe masks into one loop instead of hardcoding per pipe.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507630626-23806-4-git-send-email-mika.kahola@intel.com

When we write to ELSP, it triggers a context preemption at the earliest
arbitration point (3DPRIMITIVE, some PIPECONTROLs, a few other
operations and the explicit MI_ARB_CHECK). If this is to the same
context, it triggers a LITE_RESTORE where the RING_TAIL is merely
updated (used currently to chain requests from the same context
together, avoiding bubbles). However, if it is to a different context, a
full context-switch is performed and it will start to execute the new
context saving the image of the old for later execution.

Previously we avoided preemption by only submitting a new context when
the old was idle. But now we wish embrace it, and if the new request has
a higher priority than the currently executing request, we write to the
ELSP regardless, thus triggering preemption, but we tell the GPU to
switch to our special preemption context (not the target). In the
context-switch interrupt handler, we know that the previous contexts
have finished execution and so can unwind all the incomplete requests
and compute the new highest priority request to execute.

It would be feasible to avoid the switch-to-idle intermediate by
programming the ELSP with the target context. The difficulty is in
tracking which request that should be whilst maintaining the dependency
change, the error comes in with coalesced requests. As we only track the
most recent request and its priority, we may run into the issue of being
tricked in preempting a high priority request that was followed by a
low priority request from the same context (e.g. for PI); worse still
that earlier request may be our own dependency and the order then broken
by preemption. By injecting the switch-to-idle and then recomputing the
priority queue, we avoid the issue with tracking in-flight coalesced
requests. Having tried the preempt-to-busy approach, and failed to find
a way around the coalesced priority issue, Michal's original proposal to
inject an idle context (based on handling GuC preemption) succeeds.

The current heuristic for deciding when to preempt are only if the new
request is of higher priority, and has the privileged priority of
greater than 0. Note that the scheduler remains unfair!

v2: Disable for gen8 (bdw/bsw) as we need additional w/a for GPGPU.
Since, the feature is now conditional and not always available when we
have a scheduler, make it known via the HAS_SCHEDULER GETPARAM (now a
capability mask).
v3: Stylistic tweaks.
v4: Appease Joonas with a snippet of kerneldoc, only to fuel to fire of
the preempt vs preempting debate.
Suggested-by: NMichal Winiarski <michal.winiarski@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003203453.15692-8-chris@chris-wilson.co.uk

Only init / reset the display interrupts during power well enabling /
disabling if the i915 interrupts are enabled. So far we did the
init / reset during driver loading / resuming too, where
initialization / enabling of the i915 interrupts happens only at a later
point. This didn't cause a problem due to GEN8_MASTER_IRQ_CONTROL being
cleared, but triggered gen3_assert_iir_is_zero() in GEN8_IRQ_INIT_NDX().

References: https://bugs.freedesktop.org/show_bug.cgi?id=102988
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20170928100624.15533-1-imre.deak@intel.com

One of the differences I spotted for GEN8+ platforms when
compared to older platforms is that spec for BDW+ includes
this sentence:

"The first CRC done indication after CRC is first enabled is
from only a partial frame, so it will not have the expected
CRC result."

This is an indication that on BDW+ platforms, by the time
we receive the interrupt the CRC is not accurate yet for
the full frame. That would be ok, because we are already
skipping the first CRC for all platforms. However the comment
on the code state that it is for some unknown reason. Also,
on CHV (gen8 lp) we were already discarding the second CRC
as well to make sure we have a reliable CRC on hand.

So based on all ou tests and bugs it seems that it is not
on CHV that needs to discard 2 first CRCs, but all BDW+
platforms.

Starting on SKL we have this CRC done bit (24), but the
experiments around the use of this bit wasn't that stable
as just discarding the second CRC. So, let's for now
just move with CHV solution for all gen8+ platforms and
make our CI a bit more stable.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102374
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101309
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: NMika Kahola <mika.kahola@intel.com>
Reviewed-by: NMika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170928002040.7917-1-rodrigo.vivi@intel.com

For certain platforms on certain encoders, timings are driven
from port instead of pipe. Thus, we can't rely on pipe scanline
registers to get the timing information. Some cases scanline
register read will not be functional.
This is causing vblank evasion logic to fail since it relies on
scanline, causing atomic update failure warnings.

This patch uses pipe framestamp and current timestamp registers
to calculate scanline. This is an indirect way to get the scanline.
It helps resolve atomic update failure for gen9 dsi platforms.

v2: Addressed Ville and Daniel's review comments. Updated the
register MACROs, handled race condition for register reads,
extracted timings from the hwmode. Removed the dependency on
crtc->config to get the encoder type.

v3: Made get scanline function generic

v4: Addressed Ville's review comments. Added a flag to decide timestamp
based scanline reporting. Changed 64bit variables to u32

v5: Adressed Ville's review comments. Put the scanline compute function
at the place of caller. Removed hwmode flags from uapi and used a local
i915 data structure instead.

v6: Used vblank hwmode to get the timings.

v7: Fixed sparse warnings, indentation and minor review comments.

v8: Limited this only for Gen9 DSI.

Credits-to: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NChandra Konduru <chandra.konduru@intel.com>
Signed-off-by: NVidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1506347761-4201-1-git-send-email-vidya.srinivas@intel.com

i830 seems to occasionally forget the PIPESTAT enable bits when
we read the register. These aren't the only registers on i830 that
have problems with RMW, as reading the double buffered plane
registers returns the latched value rather than the last written
value. So something similar is perhaps going on with PIPESTAT.

This corruption results on vblank interrupts occasionally turning off
on their own, which leads to vblank timeouts and generally a stuck
display subsystem.

So let's not RMW the pipestat enable bits, and instead use the cached
copy we have around.

Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170914151731.5034-1-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Engine's execlist related items have been increasing to
a point where a separate struct is warranted. Carve execlist
specific items to a dedicated struct to add clarity.

v2: add kerneldoc and fix whitespace (Joonas, Chris)
v3: csb_mmio changes, rebase
v4: s/\b(el|execlist)\b/execlists/ (Joonas)
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com> (v3)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170922124307.10914-1-mika.kuoppala@intel.com

Our global struct with params is named exactly the same way
as new preferred name for the drm_i915_private function parameter.
To avoid such name reuse lets use different name for the global.

v5: pure rename
v6: fix

Credits-to: Coccinelle

@@
identifier n;
@@
(
-	i915.n
+	i915_modparams.n
)
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjala <ville.syrjala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170919193846.38060-1-michal.wajdeczko@intel.com