The default hop penalty is currently set to 15, which is applied like
that for multi interface devices (e.g. dual band APs). Single band
devices will still use an effective penalty of 30 (hop penalty + wifi
penalty).

After receiving reports of too long paths in mesh networks with dual
band APs which were fixed by increasing the hop penalty, we'd like to
suggest to increase that default value in the default setting as well.
We've evaluated that increase in a handful of medium sized mesh
networks (5-20 nodes) with single and dual band devices, with changes
for the better (shorter routes, higher throughput) or no change at all.

This patch changes the hop penalty to 30, which will give an effective
penalty of 60 on single band devices (hop penalty + wifi penalty).
Signed-off-by: NSimon Wunderlich <simon@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

This patch removes unnecessary logspam which resulted from superfluous
calls to net_ratelimit(). With the supplied patch, net_ratelimit() is
called after the loglevel has been checked.
Signed-off-by: NAndré Gaul <gaul@web-yard.de>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Reported by checkpatch with the following warning:
WARNING: Prefer kmalloc_array over kmalloc with multiply
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>

As pointed out by the intel guys, there is no need to hold rcu read lock in
cxgbi_inet6addr_handler(), this patch removes it.

Fixes: 759a0cc5 ("cxgb4i: Add ipv6 code to driver, call into libcxgbi ipv6 api")
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Thomas Graf says:

====================
Lockless netlink_lookup() with new concurrent hash table

Netlink sockets are maintained in a hash table to allow efficient lookup
via the port ID for unicast messages. However, lookups currently require
a read lock to be taken. This series adds a new generic, resizable,
scalable, concurrent hash table based on the paper referenced in the first
patch. It then makes use of the new data type to implement lockless
netlink_lookup().

Patch 3/3 to convert nft_hash is included for reference but should be
merged via the netfilter tree. Inclusion in this series is to provide
context for the suggested API.

Against net-next since the initial user of the new hash table is in net/

Changes:
v4-v5:
 - use GFP_KERNEL to alloc Netlink buckets as suggested by Nikolay
   Aleksandrov
 - free nft hash element on removal as spotted by Nikolay Aleksandrov
   and Patrick McHardy
v3-v4:
 - fixed wrong shift assignment placement as spotted by Nikolay Aleksandrov
 - reverted default size of nft_hash to 4 as requested by Patrick McHardy,
   default size for other hash tables remains at 64 if no hint is given
 - fixed copyright as requested by Patrick McHardy
v2-v3:
 - fixed typo in nft_hash_destroy() when passing rhashtable handle
v1-v2:
 - fixed traversal off-by-one as spotted by Tobias Klauser
 - removed unlikely() from BUG_ON() as spotted by Josh Triplett
 - new 3rd patch to convert nft_hash to rhashtable
 - make rhashtable_insert() return void
 - nl_sk_hash_lock must be a mutex
 - fixed wrong name of rht_shrink_below_30()
 - exported symbols rht_grow_above_75() and rht_shrink_below_30()
 - allow table freeing with RCU callback
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sizing of the hash table and the practice of requiring a lookup
to retrieve the pprev to be stored in the element cookie before the
deletion of an entry is left intact.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NPatrick McHardy <kaber@trash.net>
Reviewed-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Heavy Netlink users such as Open vSwitch spend a considerable amount of
time in netlink_lookup() due to the read-lock on nl_table_lock. Use of
RCU relieves the lock contention.

Makes use of the new resizable hash table to avoid locking on the
lookup.

The hash table will grow if entries exceeds 75% of table size up to a
total table size of 64K. It will automatically shrink if usage falls
below 30%.

Also splits nl_table_lock into a separate mutex to protect hash table
mutations and allow synchronize_rcu() to sleep while waiting for readers
during expansion and shrinking.

Before:
   9.16%  kpktgend_0  [openvswitch]      [k] masked_flow_lookup
   6.42%  kpktgend_0  [pktgen]           [k] mod_cur_headers
   6.26%  kpktgend_0  [pktgen]           [k] pktgen_thread_worker
   6.23%  kpktgend_0  [kernel.kallsyms]  [k] memset
   4.79%  kpktgend_0  [kernel.kallsyms]  [k] netlink_lookup
   4.37%  kpktgend_0  [kernel.kallsyms]  [k] memcpy
   3.60%  kpktgend_0  [openvswitch]      [k] ovs_flow_extract
   2.69%  kpktgend_0  [kernel.kallsyms]  [k] jhash2

After:
  15.26%  kpktgend_0  [openvswitch]      [k] masked_flow_lookup
   8.12%  kpktgend_0  [pktgen]           [k] pktgen_thread_worker
   7.92%  kpktgend_0  [pktgen]           [k] mod_cur_headers
   5.11%  kpktgend_0  [kernel.kallsyms]  [k] memset
   4.11%  kpktgend_0  [openvswitch]      [k] ovs_flow_extract
   4.06%  kpktgend_0  [kernel.kallsyms]  [k] _raw_spin_lock
   3.90%  kpktgend_0  [kernel.kallsyms]  [k] jhash2
   [...]
   0.67%  kpktgend_0  [kernel.kallsyms]  [k] netlink_lookup
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Reviewed-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Generic implementation of a resizable, scalable, concurrent hash table
based on [0]. The implementation supports both, fixed size keys specified
via an offset and length, or arbitrary keys via own hash and compare
functions.

Lookups are lockless and protected as RCU read side critical sections.
Automatic growing/shrinking based on user configurable watermarks is
available while allowing concurrent lookups to take place.

Objects to be hashed must include a struct rhash_head. The reason for not
using the existing struct hlist_head is that the expansion and shrinking
will have two buckets point to a single entry which would lead in obscure
reverse chaining behaviour.

Code includes a boot selftest if CONFIG_TEST_RHASHTABLE is defined.

[0] https://www.usenix.org/legacy/event/atc11/tech/final_files/Triplett.pdfSigned-off-by: NThomas Graf <tgraf@suug.ch>
Reviewed-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Aaron Brown says:

====================
Intel Wired LAN Driver Updates

This series contains updates to the i40e and i40evf drivers.

Vasu adds FCOE support, build options and a documentation pointer to i40e.

Shannon exposes a Firmware API request used to do register writes on the
driver's behalf and disables local loopback on VMDQ VSI in order to stop the
VEB from echoing the VMDQ packets back at the VSI.

Ashish corrects the vf_id offset for virtchnl messages in the case of multiple
PFs, removes support for vf unicast promiscuos mode to disallow VFs from
receiving traffic intended for another VF, updates the vfr_stat state check to
handle the existing and future mechanism and adds an adapter state check to
prevent re-arming the watchdog timer after i40evf_remove has been called and
the timer has been deleted.

Serey fixes an issue where a guest OS would panic when removing the vf driver
while the device is being reset due to an attempt to clean a non initialized
mac_filter_list.

Akeem makes a minor comment change.

Jessie changes an instance of sprintf to snprintf that was missed when the
driver was converted to use snprintf everywhere.

Mitch plugs a few memory leaks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing VF driver during device still in reset caused guest OS panic.

in the i40evf_remove(), we're trying to clean mac_filter_list which has
not been initialized since the device is still stuck at the reset.
The change is to initialize the filter_list before setting any task.

Change-ID: I8b59df7384416c7e6f2d264b598f447e1c2c92b0
Signed-off-by: NSerey Kong <serey.kong@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the driver is loaded and then unloaded before the interface is
brought up, then it will allocate a MAC filter entry and never free it.
To fix this, on unload, run through the mac filter list and free all the
entries. We also do this during reset recovery when the driver cannot
contact the PF and needs to shut down completely.

Change-ID: I15fabd67eb4a1bfc57605a7db60d0b5d819839db
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a memory leak. Driver was allocating memory for queue vectors on
init but not freeing them on shutdown. These need to be freed at two
different times: during module unload, and during reset recovery when
the driver cannot contact the PF driver and needs to give up.

Change-ID: I7c1d0157a776e960d4da432dfe309035aad7c670
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add in an adapter state check to prevent re-arming watchdog timer after
i40evf_remove has been called and timer has been deleted.

Change-ID: I636ba7c6322be8cbf053231959f90c0a2d8d803a
Signed-off-by: NAshish Shah <ashish.n.shah@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously defined state I40E_VFR_VFACTIVE uses bit 1 which is now set to
"reserved."  Update the state checks to also include I40E_VFR_COMPLETED.
This change will allow the VF to work with both existing and future PFs.

Change-ID: Ifd1d34f79f3b0ffd6d2550ee4dadc55825ff52f8
Signed-off-by: NAshish Shah <ashish.n.shah@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the ability of a VF to set unicast promiscuous mode.
Considered to be a security risk to allow VFs to receive traffic
intended for other VFs so don't allow it, simply ignore the flag.

Also fix it to send the correct seid to aq for multicast promiscuous set.

Change-ID: Icb9c49a281a8e9d3aeebf991ef1533ac82b84b14
Signed-off-by: NAshish Shah <ashish.n.shah@intel.com>
Tested-by: NJim Young  <jamesx.m.young@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes comment for reset reason

Change-ID: I6fda4fa292255e6eb0f874502b4d38d722149b10
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver was converted to use snprintf everywhere but this one function.
Just use snprintf, instead of sprintf.

Also a small spelling correction in a comment.

Change-ID: I59d45f94a52754c7b4cd6034df9a61d8132b7f77
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The local loopback should only be enabled for VSIs that are supporting
cascaded VEBs or VEPA setups.  This is not the case here, and we need
to stop the VEB from echoing the VMDQ VSI packets back at the VSI.

Change-ID: I9dfb6ac79db24d04360d7efde62d81e20abc5090
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vf_id needs to be offset by the vf_base_id from hw function capabilities
for the case of multiple PFs.

Change-ID: I20ca8621f98e9cdf98649380b8eeaa35db52677c
Signed-off-by: NAshish Shah <ashish.n.shah@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the HW registers are no longer in debug mode and many are
locked down for writes, we need to expose the Firmware API request
used to do writes on the driver's behalf.

Change-ID: I09a05c4dc9ea0b24c00193faac34d7799eaa8496
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds newly added FCoE files to the build but only if FCoE module is configured.

Also, updates i40e document for added FCoE support.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds FCoE specific code to existing i40e core driver to:-

1. have separate FCoE VSI with additional FCoE queues pairs.
2. have FCoE related hash defines.
3. have additional FCoE related stats code.
4. export and then re-use existing functions required by FCoE build.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds FCoE ( Fibre Channel Over Ethernet ) code for
Intel XL710 adapters. This patch is limited to only new FCoE
offloads code in newly added files by this patch and then
following patches in the series modifies rest of the existing
driver to enable FCoE with i40e driver.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tom Lendacky says:

====================
amd-xgbe: AMD XGBE driver update 2014-08-01

The following series of patches includes minor fixes/updates to the
driver.

- Remove some uses of spinlock around ethtool/phylib areas
- Update Rx/Tx ready check logic
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current time range waiting for Rx/Tx to become ready can sometimes
be too short if a connection is not present.  Increase the number of
retries and the sleep to give a bit more time. Also, change level of
the message issued from _err to _dbg if Rx/Tx do not become ready
since the underlying logic will function as if no link is established
and retry eventually.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the spinlocks around the ethtool get and set settings
functions and within the link adjustment callback routine.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces the use of managed interfaces like
devm_ioremap_resource and does away with the calls to free the
allocated memory in the probe and remove functions. Also, some
labels and variable are done away with. This fixes a bug as there
was a missing release_mem_region in the remove function.
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces the use of devm_ioremap_resource, devm_kmalloc and
does away with the functions to free the allocated memory in the probe
and remove functions. Also, some labels are done away with. A bug is
fixed as two regions are allocated in the probe function, but only one
is freed in the remove function.
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces the use of managed interfaces like
devm_ioremap_resource and does away with the functions to free the
allocated memory in the probe and remove functions. Also, many labels
are done away with. The field size in no longer needed and is hence
removed from the struct net_local.
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHisashi Nakamura <hisashi.nakamura.ak@renesas.com>
[uli: added bindings documentation]
Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sathya Perla says:

====================
be2net: patch set

Patch 1 fixes a regression caused by a previous commit on net-next.
Old versions of BE3 FW may not support cmds to re-provision (and hence
optimize) resources/queues in SR-IOV config. Do not treat this FW cmd
failure as fatal and fail the function initialization. Instead, just
enable SR-IOV with the resources provided by the FW.

Patch 2 ignores a VF mac address setting if the new mac is already active
on the VF.

Patch 3 adds support to delete a FW-dump via ethtool on Lancer adapters.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support to delete an existing FW-dump in Lancer via ethtool.
Initiating a new dump is not allowed if a FW dump is already present in the
adapter. The existing dump has to be first explicitly deleted.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ndo_set_vf_mac() call may be issued for a mac-addr that is already
active on a VF. If so, silently ignore the request.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Old versions of BE3 FW may not support cmds to re-provision (and hence
optimize) resources/queues in SR-IOV config. Do not treat this FW cmd
failure as fatal and fail the function initialization. Instead, just
enable SR-IOV with the resources provided by the FW.

Prior to the "create optimal number of queues on SR-IOV config" patch
such failures were ignored.
Fixes: bec84e6b ("create optimal number of queues on SR-IOV config")
Reported-by: NEduardo Habkost <ehabkost@redhat.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
inet: frags: cleanup and kmem_cache use

This patchset does a couple of small cleanups in patches 1-5 and then in
patch 06 it introduces the use of kmem_cache for allocation/freeing of
inet_frag_queue+header objects.

v2: Broke up patch 02 into 3 patches as David suggested

Here are the results of a couple of netperf runs:
netperf options: -l 30 -I95,5 -i 15,10 -m 64k

- 10 gig before the patchset
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.155.1 () port 0 AF_INET : +/-2.500% @ 95% conf.
Socket  Message  Elapsed      Messages
Size    Size     Time         Okay Errors   Throughput
bytes   bytes    secs            #      #   10^6bits/sec

212992   64000   30.00      442466      0    7551.39
212992           30.00      439130           7494.45

- 10 gig after the patchset
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.155.1 () port 0 AF_INET : +/-2.500% @ 95% conf.
Socket  Message  Elapsed      Messages
Size    Size     Time         Okay Errors   Throughput
bytes   bytes    secs            #      #   10^6bits/sec

212992   64000   30.00      458846      0    7830.94
212992           30.00      457575           7809.25

- Virtio before the patchset
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.144.1 () port 0 AF_INET : +/-2.500% @ 95% conf.
Socket  Message  Elapsed      Messages
Size    Size     Time         Okay Errors   Throughput
bytes   bytes    secs            #      #   10^6bits/sec

212992   64000   30.00      735000      0    12543.96
212992           30.00      560322           9562.79

- Virtio after the patchset
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.144.1 () port 0 AF_INET : +/-2.500% @ 95% conf.
Socket  Message  Elapsed      Messages
Size    Size     Time         Okay Errors   Throughput
bytes   bytes    secs            #      #   10^6bits/sec

212992   64000   30.00      731729      0    12488.14
212992           30.00      647241           11046.21
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use kmem_cache to allocate/free inet_frag_queue objects since they're
all the same size per inet_frags user and are alloced/freed in high volumes
thus making it a perfect case for kmem_cache.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Acked-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have INET_FRAG_EVICTED we might as well use it to stop
sending icmp messages in the "frag_expire" functions instead of
stripping INET_FRAG_FIRST_IN from their flags when evicting.
Also fix the comment style in ip6_expire_frag_queue().
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Reviewed-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a couple of functions' declaration alignments.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the flags to an enum definion, swap FIRST_IN/LAST_IN to be in increasing
order and add comments explaining each flag and the inet_frag_queue struct
members.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The last_in field has been used to store various flags different from
first/last frag in so give it a more descriptive name: flags.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>