Enable HS-USB device for the Lager board, defining the GPIO that the driver
should check when probing. Since this board doesn't have the OTG ID pin, we
assume that GP5_18 (USB0_PWEN) is an ID pin because it is 1 when the SW5 is
in position 2-3 (meaning USB function) and 0 in other positions.

Note that there will be pinctrl-related error messages if both internal PCI
and HS-USB drivers are enabled but they should be just ignored.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: added pin node and prop, moved device node, fixed summary, supplemented
changelog]
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Define the R8A7790 generic part of the HS-USB device node.
It is up to the board file to enable the device.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: fixed summary, added changelog]
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Since the PHY of USB3.0 and EHCI/OHCI ch2 are the same, the USB3.0
driver cannot use the phy driver when the EHCI/OHCI ch2 already used it:

phy phy-e6590100.usb-phy.3: phy init failed --> -16
xhci-hcd: probe of ee000000.usb failed with error -16

If so, we have to unbind the EHCI/OHCI ch2, and then we have to bind
the USB3.0 driver as the following:

  echo 0000:02:02.0 > /sys/bus/pci/drivers/ehci-pci/unbind
  echo 0000:02:01.0 > /sys/bus/pci/drivers/ohci-pci/unbind
  echo ee000000.usb > /sys/bus/platform/drivers/xhci-hcd/bind

Note that there will be pinctrl-related error messages if both
internal PCI and USB3.0 are enabled but they should be just ignored:

sh-pfc e6060000.pfc: pin GP_5_22 already requested by ee0d0000.pci; cannot claim for ee000000.usb
sh-pfc e6060000.pfc: pin-182 (ee000000.usb) status -22
ata1: SATA link down (SStatus 0 SControl 300)
sh-pfc e6060000.pfc: could not request pin 182 (GP_5_22) from group usb2  on device sh-pfc
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NHisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Initialise TMU device using DT when booting bockw
using DT-reference.
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This describes all of the TMU hardware of the r8a7778.
Each node is disabled and may be enabled as necessary
by board DTS files.
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

ch0 will be used for clock events and for periodic clock events,
ch1 will be used as clock source.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NYoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NYoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NKouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NKouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The clocks property for the scifa2 device node referred to the scifa0
clock index instead of the scifa2 clock index.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

SCIF and SCIFA can be plexed onto the same wires on Lager board. The
datasheet also describes the wires as SCIFA. So, to make use of the
bigger FIFOs switch to SCIFA instead.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Describe the PCI USB devices that are behind the PCI bridges, adding necessary
links to the USB PHY device.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Describe the PCI USB devices that are behind the PCI bridges, adding necessary
links to the USB PHY device.

Based on the original work by Ben Dooks <ben.dooks@codethink.co.uk>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable USB PHY device for the Henninger board.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable USB PHY device for the Koelsch board.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Define the R8A7791 generic part of the USB PHY device node. It is up to the
board file to enable the device.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable USB PHY device for the Lager board.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Define the R8A7790 generic part of the USB PHY device node. It is up to the
board file to enable the device.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This clock drives the INTCA irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Cc: devicetree@vger.kernel.org
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The Mitsubishi AA104XD12 panel is commonly used with the Marzen, Lager
and Koelsch boards. Create a .dtsi file that describe the panel and its
connection to the board.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: resolved minor conflict]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: resolved minor conflict]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Initialise CMT1 device using DT when booting ape6evm
using DT-reference.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This describes all of the CMT1 hardware of the r8a73a4.
The node is disabled and may be enabled as necessary by board DTS files.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.

Note that we have to keep the "console=ttyS1,115200n81" parameter in
chosen/bootargs, else the console will use the default setting of 9600
baud.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.
In addition, this will allow the PM domain code to find the PM domain
for the console device.

Note that we have to keep the "console=ttySC4" parameter in
chosen/bootargs, else we only get console messages on tty0.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.

Note that we have to keep the "console=ttySC0,38400" parameter in
chosen/bootargs, else the console will use the default setting of 115200
baud.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.

Note that we have to keep the "console=" parameter in chosen/bootargs,
as this DTS is shared between legacy and multi-platform.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.

Note that we have to keep the "console=ttySC0,38400" parameter in
chosen/bootargs, else the console will use the default setting of 115200
baud.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.

Note that we have to keep the "console=" parameter in chosen/bootargs,
as this DTS is shared between legacy and multi-platform.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.

Note that we have to keep the "console=" parameter in chosen/bootargs,
as this DTS is shared between legacy and multi-platform.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>