The radiotap specification contains a flag to indicate that the sequence
number of an injected frame should not be overwritten. Parse this flag
and define and set a corresponding Tx control flag.
Signed-off-by: NMathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-2-Mathy.Vanhoef@kuleuven.beSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

In ieee80211_tx_dequeue there is a check to see if the dequeued frame
is allowed in the current state. Injected frames that are normally
not allowed are being be dropped here. Fix this by checking if a
frame was injected and if so always allowing it.
Signed-off-by: NMathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-1-Mathy.Vanhoef@kuleuven.beSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Adding bss-color configuration is only valid in HE mode.
Earlier we have enabled it by default, irrespective of
capabilities/mode. Fix that.
Reported-by: Nkernel test robot <lkp@intel.com>
Reported-by: NRajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: NP Praneesh <ppranees@codeaurora.org>
Link: https://lore.kernel.org/r/1594262781-21444-1-git-send-email-ppranees@codeaurora.org
[fix up commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This avoids flow separation issues when using software encryption.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200726130947.88145-2-nbd@nbd.nameSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

AQL does not take into account that most HT/VHT/HE traffic is A-MPDU aggregated.
Because of that, the per-packet airtime overhead is vastly overestimated.
Improve it by assuming an average aggregation length of 16 for non-legacy
traffic if not using the VO AC queue.
This should improve performance with high data rates, especially with multiple
stations
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200724182816.18678-1-nbd@nbd.nameSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch adds the necessary bits to later query the auth server
flag for every peer from iw.
Signed-off-by: NMarkus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200611140238.427461-2-markus.theil@tu-ilmenau.deSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Besides information about num of peerings and gate connectivity,
the mesh formation byte also contains a flag for authentication
server connectivity, that currently cannot be set in the mesh conf.
This patch adds this capability, which is necessary to implement
802.1X authentication in mesh mode.
Signed-off-by: NMarkus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200611140238.427461-1-markus.theil@tu-ilmenau.deSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, before being able to forward a packet between two 802.11s
nodes, both a PLINK handshake is performed upon receiving a beacon and
then later a PREQ/PREP exchange for path discovery is performed on
demand upon receiving a data frame to forward.

When running a mesh protocol on top of an 802.11s interface, like
batman-adv, we do not need the multi-hop mesh routing capabilities of
802.11s and usually set mesh_fwding=0. However, even with mesh_fwding=0
the PREQ/PREP path discovery is still performed on demand. Even though
in this scenario the next hop PREQ/PREP will determine is always the
direct 11s neighbor node.

The new mesh_nolearn parameter allows to skip the PREQ/PREP exchange in
this scenario, leading to a reduced delay, reduced packet buffering and
simplifies HWMP in general.

mesh_nolearn is still rather conservative in that if the packet destination
is not a direct 11s neighbor, it will fall back to PREQ/PREP path
discovery.

For normal, multi-hop 802.11s mesh routing it is usually not advisable
to enable mesh_nolearn as a transmission to a direct but distant neighbor
might be worse than reaching that same node via a more robust /
higher throughput etc. multi-hop path.

Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NLinus Lüssing <ll@simonwunderlich.de>
Link: https://lore.kernel.org/r/20200617073034.26149-1-linus.luessing@c0d3.blue
[fix nl80211 policy to range 0/1 only]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The low level driver adds its own opaque information
in the BSS table in the cfg80211_bss structure.

The low level driver may need to signal that this information
is no longer relevant and needs to be recreated.
Add an API to allow the low level driver to do that.

iwlwifi needs this because it keeps there an information about
the firmware's internal clock. This is kept in mac80211's
struct ieee80211_bss::sync_device_ts.
This information is populated while we scan, we add the
internal firmware's clock to each beacon which allows us to
program the firmware correctly after association so that
it'll know when (in terms of its internal clock) the DTIM
and TBTT will happen.

When the firmware is reset this internal clock is reset as
well and ieee80211_bss::sync_device_ts is no longer accurate.

iwlwifi will call this new API any time the firmware is started.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20200625111524.3992-1-emmanuel.grumbach@intel.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/latest/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200707204548.GA9320@embeddedorSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Re-write the end of 'nl80211_trigger_scan()' with a more standard, easy to
understand and future proof version.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200712173551.274448-1-christophe.jaillet@wanadoo.frSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Since commit 5fe231e8 ("cfg80211: vastly simplify locking"), the
'unlock' label at the end of 'nl80211_trigger_scan()' is useless and
misleading, because nothing is unlocked there.

Direct return can be used instead of 'err = -<error code>; goto unlock;'
construction.

Remove this label and simplify code accordingly.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200712173539.274395-1-christophe.jaillet@wanadoo.frSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

nl80211 vendor netlink dumpit, like netlink_callback->dump, should
signal successful completion by returning 0.

Currently, that will just cause dumpit to be called again, possibly
many times until an error occurs.  Since skb->len is never going to be
0 by the time dumpit is called, the only way for dumpit to signal
completion is by returning an error.  If it returns a positive value,
the current message is cancelled, but that positive value is returned
and nl80211_vendor_cmd_dump gets called again.

Fix that by passing a return value of 0 through.
Signed-off-by: NJulian Squires <julian@cipht.net>
Link: https://lore.kernel.org/r/20200720145033.401307-1-julian@cipht.net
[reword commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently rates_idx is being initialized with the value -1 and this
value is never read so the initialization is redundant and can be
removed. The next time the variable is used it is assigned a value
that is returned a few statements later. Just return i - 1 and
remove the need for rates_idx.

Addresses-Coverity: ("Unused value")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200722153830.959010-1-colin.king@canonical.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Gives drivers the definitions needed to advertise support
for S1G bands.
Signed-off-by: NThomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200602062247.23212-1-thomas@adapt-ip.com
Link: https://lore.kernel.org/r/20200731055636.795173-1-thomas@adapt-ip.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch fixes:
commit b9aaec8f ("fib: use indirect call wrappers in the most common
fib_rules_ops") which didn't consider the case when
CONFIG_IPV6_MULTIPLE_TABLES is not set.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Fixes: b9aaec8f ("fib: use indirect call wrappers in the most common fib_rules_ops")
Signed-off-by: NBrian Vazquez <brianvv@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This avoids another inderect call per RX packet which save us around
20-40 ns.

Changelog:

v1 -> v2:
- Move declaraions to fib_rules.h to remove warnings
Reported-by: Nkernel test robot <lkp@intel.com>
Signed-off-by: NBrian Vazquez <brianvv@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When red_init() fails, red_destroy() is called to clean up.
If the timer is not initialized yet, del_timer_sync() will
complain. So we have to move timer_setup() before any failure.

Reported-and-tested-by: syzbot+6e95a4fabf88dc217145@syzkaller.appspotmail.com
Fixes: aee9caa0 ("net: sched: sch_red: Add qevents "early_drop" and "mark"")
Cc: Petr Machata <petrm@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MPTCP socket's write_seq member can be read without the msk lock
held, so use WRITE_ONCE() to store it.
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MPTCP socket's write_seq member should be read with READ_ONCE() when
the msk lock is not held.
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bare TCP ack skbs are freed right after MPTCP sees them, so the work to
allocate, zero, and populate the MPTCP skb extension is wasted. Detect
these skbs and do not add skb extensions to them.
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MPTCP state machine handles disconnections on non-fallback connections,
but the mptcp_sock still needs to get notified when fallback subflows
disconnect.
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC 8684 appendix D describes the connection state machine for
MPTCP. This patch implements the DATA_FIN / DATA_ACK exchanges and
MPTCP-level socket state changes described in that appendix, rather than
simply sending DATA_FIN along with TCP FIN when disconnecting subflows.

DATA_FIN is now sent and acknowledged before shutting down the
subflows. Received DATA_FIN information (if not part of a data packet)
is written to the MPTCP socket when the incoming DSS option is parsed by
the subflow, and the MPTCP worker is scheduled to process the
flag. DATA_FIN received as part of a full DSS mapping will be handled
when the mapping is processed.

The DATA_FIN is acknowledged by the worker if the reader is caught
up. If there is still data to be moved to the MPTCP-level queue, ack_seq
will be incremented to account for the DATA_FIN when it reaches the end
of the stream and a DATA_ACK will be sent to the peer.
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After DATA_FIN has been sent, the peer will acknowledge it. An ack of
the relevant MPTCP-level sequence number will update the MPTCP
connection state appropriately.
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will be used to transition to the appropriate state on close and
determine if a DATA_FIN needs to be sent for that state transition.
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Incoming DATA_FIN headers need to propagate the presence of the DATA_FIN
bit and the associated sequence number to the MPTCP layer, even when
arriving on a bare ACK that does not get added to the receive queue. Add
structure members to store the DATA_FIN information and helpers to set
and check those values.
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since DATA_FIN information is the same for every subflow, store it only
in the mptcp_sock.
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mptcp_close() acquires the msk lock, so it clearly should not be held
before the function is called.
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A MPTCP socket where sending has been shut down should not attempt to
send additional data, since DATA_FIN has already been sent.
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC 8684-compliant DATA_FIN needs to be sent and ack'd before subflows
are closed with TCP FIN, so write DATA_FIN DSS headers whenever their
transmission has been enabled by the MPTCP connection-level socket.
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure not just the pointer itself but the whole range lies in
the user address space.  For that pass the length and then use
the access_ok helper to do the check.

Fixes: 6d04fe15 ("net: optimize the sockptr_t for unified kernel/user address spaces")
Reported-by: NDavid Laight <David.Laight@ACULAB.COM>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sockptr_advance never properly worked.  Replace it with _offset variants
of copy_from_sockptr and copy_to_sockptr.

Fixes: ba423fda ("net: add a new sockptr_t type")
Reported-by: NJason A. Donenfeld <Jason@zx2c4.com>
Reported-by: NIdo Schimmel <idosch@idosch.org>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NJason A. Donenfeld <Jason@zx2c4.com>
Tested-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was accidentally removed in an unrelated commit.

Fixes: c2f12630 ("netfilter: switch nf_setsockopt to sockptr_t")
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Print PRP specific information from node table as part of debugfs
node table display. Also display the node as DAN-H or DAN-P depending
on the info from node table.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DAN-P (Dual Attached Nodes PRP) nodes are expected to receive
traditional IP packets as well as PRP (Parallel Redundancy
Protocol) tagged (trailer) packets. PRP trailer is 6 bytes
of PRP protocol unit called RCT, Redundancy Control Trailer
(RCT) similar to HSR tag. PRP network can have traditional
devices such as bridges/switches or PC attached to it and
should be able to communicate. Regular Ethernet devices treat
the RCT as pads.  This patch adds logic to format L2 frames
from network stack to add a trailer (RCT) and send it as
duplicates over the slave interfaces when the protocol is
PRP as per IEC 62439-3. At the ingress, it strips the trailer,
do duplicate detection and rejection and forward a stripped
frame up the network stack. PRP device should accept frames
from Singly Attached Nodes (SAN) and thus the driver mark
the link where the frame came from in the node table.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As a preparatory patch to introduce PRP, refactor the code specific to
handling HSR frames into separate functions and call them through
proto_ops function pointers.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for generation of PRP supervision frames. For PRP,
supervision frame format is similar to HSR version 0, but have
a PRP Redundancy Control Trailer (RCT) added and uses a different
message type, PRP_TLV_LIFE_CHECK_DD. Also update
is_supervision_frame() to include the new message type used for
PRP supervision frame.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As a preparatory patch to introduce support for PRP protocol, add a
protocol ops ptr in the private hsr structure to hold function
pointers as some of the functions at protocol level packet
handling is different for HSR vs PRP. It is expected that PRP will
add its of set of functions for protocol handling. Modify existing
hsr_announce() function to call proto_ops->send_sv_frame() to send
supervision frame for HSR. This is expected to be different for PRP.
So introduce a ops function ptr, send_sv_frame() for the same and
initialize it to send_hsr_supervsion_frame(). Modify hsr_announce()
to call proto_ops->send_sv_frame().
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As a preparatory patch to introduce PRP protocol support in the
driver, refactor the skb init code to a separate function.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Parallel Redundancy Protocol (PRP) is another redundancy protocol
introduced by IEC 63439 standard. It is similar to HSR in many
aspects:-

 - Use a pair of Ethernet interfaces to created the PRP device
 - Use a 6 byte redundancy protocol part (RCT, Redundancy Check
   Trailer) similar to HSR Tag.
 - Has Link Redundancy Entity (LRE) that works with RCT to implement
   redundancy.

Key difference is that the protocol unit is a trailer instead of a
prefix as in HSR. That makes it inter-operable with tradition network
components such as bridges/switches which treat it as pad bytes,
whereas HSR nodes requires some kind of translators (Called redbox) to
talk to regular network devices. This features allows regular linux box
to be converted to a DAN-P box. DAN-P stands for Dual Attached Node - PRP
similar to DAN-H (Dual Attached Node - HSR).

Add a comment at the header/source code to explicitly state that the
driver files also handles PRP protocol as well.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>