Remove st_sensors_get_buffer_element symbol export since not explicitly
used outside of st_sensors driver.
Signed-off-by: NGregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Initial support for ST LPS22HB pressure sensor. Datasheet:
http://www2.st.com/resource/en/datasheet/lps22hb.pdf

Features:
* pressure data and timestamping channels
* sampling frequency selection
* interrupt based trigger
* over I2C or SPI
Signed-off-by: NGregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This structure has not been optional for a long time (if ever) but the
code implies that it is.  As we then use it later in a fashion that would
crash if it was in fact NULL, it's inconsistent so fix it up by removing
unnecessary checks.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add datasheet names for ADC channels to allow iio consumers access.
Signed-off-by: NMatt Ranostay <matt.ranostay@intel.com>
Acked-by: NDaniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Enable humidity support for the BME280 part
Signed-off-by: NMatt Ranostay <matt.ranostay@intel.com>
Acked-by: NVlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This driver does not call i2c_smbus_read|write_byte_data(),
so remove the corresponding functionality test. It uses regmap
to handle byte transfers transparently.
Signed-off-by: NAlison Schofield <amsfield22@gmail.com>
Reviewed-by: NKuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: NMatt Ranostay <matt.ranostay@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The Nuvoton NAU7802 ADC is able to adjust its gain but prior knowledge of
its possible values was required to adjust it. Users had to guess the
possible gain values based on the ADC datasheet or on this driver's code.

This exposes the possible values in the in_voltage_scale_available file of
each nau7802 ADC device. The gain is set for the whole ADC and is therefore
not configurable by channel. Thus, there exists only one
in_voltage_scale_available file for each nau7802 ADC device even if it has
two separate channels.
Signed-off-by: NQuentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add implementation for Maxim MAX5487, MAX5488, MAX5489
digital potentiometers.

Datasheet:
http://datasheets.maximintegrated.com/en/ds/MAX5487-MAX5489.pdfSigned-off-by: NCristina Moraru <cristina.moraru09@gmail.com>
CC: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The I2C drivers have an i2c_device_id array but that information isn't
exported to the modules using the MODULE_DEVICE_TABLE() macro. So the
modules autoloading won't work if the I2C device is registered using
OF or legacy board files due missing alias information in the modules.

The issue was found using Kieran Bingham's coccinelle semantic patch:
https://lkml.org/lkml/2016/5/10/520Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Signed-off-by: NTiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

TI ADS1115 is a 16-bit resolution ADC that is register map
compatible with the ADS1015 device.
Signed-off-by: NMatt Ranostay <matt.ranostay@intel.com>
Acked-by: NDaniel Baluta <daniel.baluta@intel.com>
Acked-by: NCrt Mori <cmo@melexis.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

BMM150 is register compatible with magnetometer part of
BMC156.

Datasheet is at:
http://www.mouser.com/ds/2/783/BST-BMM150-DS001-01-786480.pdfSigned-off-by: NDaniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This commit adds basic support for the Bosch Sensortec BMA220
digital triaxial acceleration sensor.
The device datasheet can be found here:

http://www.mouser.com/pdfdocs/BSTBMA220DS00308.PDF

Includes:
- raw readings
- ACPI detection
- power management
Signed-off-by: NTiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Actually I2C_FUNC_SMBUS_WORD_DATA isn't need for this device, and regmap
handles all single byte reads transparently.
Signed-off-by: NMatt Ranostay <mranostay@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This adds the following sysfs files according to the iio ABI:

-rw-r--r--    4096 in_accel_oversampling_ratio
-r--r--r--    4096 in_accel_oversampling_ratio_available

Internally, the device knows about 4 different power modes that differ
in oversampling ratio (and power consumption). We just show the user
what oversampling ratio(s) is/are available, depending on the current
frequency.

The referenced table in the datasheets makes it easier to understand.
Signed-off-by: NMartin Kepplinger <martink@posteo.de>
Signed-off-by: NChristoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Signed-off-by: NDaniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

We register a new device type named "dummy", this will create a
configfs entry under:
	* /config/iio/devices/dummy.

Creating dummy devices is now as simple as:

$ mkdir /config/iio/devices/dummy/my_dummy_device
Signed-off-by: NDaniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This is similar with support for creating triggers via configfs.
Devices will be hosted under:
	* /config/iio/devices

We allow users to register "device types" under:
	* /config/iio/devices/<device_types>/
Signed-off-by: NDaniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Rename this definition, no functional changes.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

These definitions are not currently used and if the functionality
they represent is needed the values should be added back to a table
for easy userspace use.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The current channel number for the LEDs should match the stage
number that they are active during, fix this here.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Currently the TIA gain settings are exported to userspace as sysfs
entries that do not clearly represent their internal relation to the
sampling stages. The gain settings are enabled on a per-stage basis,
this can be seen in figure 24 of the current AFE4404 datasheet.
These gain settings should therefore be tied to the channels that are
read during these stages. Make this change here.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

These drivers can use regmap fields to access fields in registers, this
allows us to remove some macros/defines and simplify code, do this here.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

These AFEs have 4 ADC mesuring stages (called LED2, ALED2, LED1, and
ALED1 in the datasheet), we map these as channels, these stages can serve
different purposes depending on the application. For instance the AFE4404
has an additional LED (LED3), this LED can be timed to be active during
stage 2 (or anystage, but the datasheet describes this case and the name
of the stage reflects this use). This ability is used further in upcoming
parts that tie the front-end gain and the LED timings together. For these
reasons we remove explicit naming the channels.

Without channel names it is best that the index numbers are in order to
match the stage number, reorder the channel numbers.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Input channel LED3 is only an alias for stage ALED2, this virtual channel
does nothing for us, remove this channel.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

No channel in the afe4403 driver has IIO_CHAN_INFO_OFFSET set so
remove the handlers for this.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The LED channels are not scannable and so scan_index should
be negative, fix this here.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Locking the two gain stages to the same setting adds no value for us,
so initialize them as unlocked and remove the sysfs for unlocking them.
This also allows us to greatly simplify showing and setting the gain
registers.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The drivers set some register values during initialization that can be
set at runtime, these defaults were used in testing but are not
necessary, remove these.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The drivers DT tables are not built-in when OF is not enabled, this does
not save us enough to justify ugly ifdefs. Clean this up.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Fix kernel-doc formatting for structs, and while we are making little
fixes, clarify the module description and update the copywrite.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Signed-off-by: NDaniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Disabling of the touchscreen IRQs should be done in
mxs_lradc_disable_ts. So disable only the masked virtual channels
in mxs_lradc_hw_stop and finally remove the unused function
mxs_lradc_irq_en_mask.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Tested-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

After using devm_input_allocate_device for registration
the function mxs_lradc_ts_unregister isn't necessary anymore
since mxs_lradc_ts_close already does the job.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Suggested-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch simplifies the TS registration of mxs-lradc by
using devm_input_allocate_device.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Minimal implementation of an IIO driver for the Freescale
MMA7660FC 3-axis accelerometer. Datasheet:
http://www.nxp.com/files/sensors/doc/data_sheet/MMA7660FC.pdf

Includes:
- ACPI support;
- read_raw for x,y,z axes;
- reading and setting the scale (range) parameter.
- power management
Signed-off-by: NConstantin Musca <constantin.musca@intel.com>
Reviewed-by: NMartin Klepplinger <martink@posteo.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The device has simple 8-bit registers but the driver incorrectly uses
block or word reads without checking functionality bits.

Fix by using i2c_smbus_read_i2c_block_data_or_emulated instead of
i2c_smbus_read_i2c_block_data or i2c_smbus_read_word_data. This will
check functionality bits and use the fastest available transfer method.
Signed-off-by: NCrestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This device is a package containing a MPU6050-like sensor and an AK8975
magnetometer. The magnetometer component is supported by the existing
ak8975 driver.

This patch also rephrases the Kconfig descriptions.
Signed-off-by: NCrestez Dan Leonard <leonard.crestez@intel.com>
Acked-by: NGe Gao <ggao@invensense.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>