Avoid rc6 counter going backward in close to 0% RC6 scenarios like:

    15.005477996        114,246,613 ns   i915/rc6-residency/
    16.005876662            667,657 ns   i915/rc6-residency/
    17.006131417              7,286 ns   i915/rc6-residency/
    18.006615031 18,446,744,073,708,914,688 ns   i915/rc6-residency/
    19.007158361 18,446,744,073,709,447,168 ns   i915/rc6-residency/
    20.007806498                  0 ns   i915/rc6-residency/
    21.008227495          1,440,403 ns   i915/rc6-residency/

There are two aspects to this fix.

First is not assuming rc6 value zero means GT is asleep since that can
also mean GPU is fully busy and we do not want to enter the estimation
path in that case.

Second is ensuring monotonicity on the estimation path itself. I suspect
what is happening is with extremely rapid park/unpark cycles we get no
updates on the real rc6 and therefore have to careful not to
unconditionally trust use last known real rc6 when creating a new
estimation.

v2:
 * Simplify logic by not tracking the estimate but last reported value.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 16ffe73c ("drm/i915/pmu: Use GT parked for estimating RC6 while asleep")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> # v1
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217142057.1000-1-tvrtko.ursulin@linux.intel.com

Move all of haswell_crtc_disable() into the encoder
.post_disable() hooks. Now we're left with just
calling the .disable() and .post_disable() hooks
back to back.

I chose to move the code into the .post_disable() hook instead
of the .disable() hook as most of the sequence is currently
implemented in the .post_disable() hook.

We should collapse it all down to just one hook and then the
encoders can drive the modeset sequence fully. But that may
need some further refactoring as we currently call the
ddi .post_disable() hook from mst code and we can't just
replace that with a call to the ddi .disable() hook.

Should also follow up with similar treatment for the enable
sequence but let's start here where it's easier.

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-5-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

To make life easier in the future let's pass the old crtc state
to intel_crtc_vblank_off() just like we already do for its
counterpart intel_crtc_vblank_on().

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-4-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

To make life easier in the future let's pass the old crtc state
to skylake_scaler_disable() just like we already do for
for its ancestor ironlake_pfit_disable().

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-3-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

HSW+ platforms call encoder .post_disable() and .post_pll_disable()
back to back. And since we don't even disable the PLL in between
let's just move everything into .post_disable().

intel_dp_mst does forward the .post_disable() call to intel_ddi at
the very end of its own .post_disable() hook, so this time MST
I shouldn't even break MST by accident.

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-2-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

Remove the pointless vfunc detour for hsw_fdi_link_train()
and just call it directly. Also pass the encoder in so we
can nuke the silly encoder loop within.

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-1-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

For the sake of symmetry with the crtc stuff let's add
a helper to reset the plane state to sane default values.
For the moment this only gets caller from the plane init.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107142417.11107-5-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

We have a few places where we want to reset a crtc state to its
default values. Let's add a helper for that. We'll need the new
__drm_atomic_helper_crtc_state_reset() helper for this to allow
us to just reset the state itself without clobbering the
crtc->state pointer.

And while at it let's zero out the whole thing, except a few
choice member which we'll mark as "invalid". And thanks to this
we can now nuke intel_crtc_init_scalers().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107142417.11107-4-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

We already have alloc/free helpers for planes, add the same for
crtcs. The main benefit is we get to move all the annoying state
initialization out of the main crtc_init() flow.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107142417.11107-3-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

Let's get rid of the redundant intel_ prefix on our variables.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107142417.11107-2-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

For very light workloads that frequently park, acquiring the display
power well (required to prevent the dmc from trashing the system) takes
longer than the execution. A good example is the igt_coherency selftest,
which is slowed down by an order of magnitude in the worst case with
powerwell cycling. To prevent frequent cycling, while keeping our fast
soft-rc6, use a timer to delay release of the display powerwell.

Fixes: 31177017 ("drm/i915/gt: Schedule request retirement when timeline idles")
References: https://gitlab.freedesktop.org/drm/intel/issues/848Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218093504.3477048-1-chris@chris-wilson.co.uk

Since obj->frontbuffer is no longer protected by the struct_mutex, as we
are processing the execbuf, it may be removed. Mark the
intel_frontbuffer as rcu protected, and so acquire a reference to
the struct as we track activity upon it.

Closes: https://gitlab.freedesktop.org/drm/intel/issues/827
Fixes: 8e7cb179 ("drm/i915: Extract intel_frontbuffer active tracking")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: <stable@vger.kernel.org> # v5.4+
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218104043.3539458-1-chris@chris-wilson.co.uk

If the whole GT is asleep, we know that each engine must also be asleep
and so we can quickly return without checking them all.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218000756.3475668-1-chris@chris-wilson.co.uk

If we inherit an error along the fence chain, we skip the main work
callback and go straight to the error. In the case of the vma bind
worker, we only dropped the pinned pages from the worker.

In the process, make sure we call the release earlier rather than wait
until the final reference to the fence is dropped (as a reference is
kept while being listened upon).
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216161717.2688274-1-chris@chris-wilson.co.uk

The Gen11+ and the legacy function differ in the register and value
written to interrupt the GuC. However, while on older gen the value
matches a bit on the register, on Gen11+ the value is a SW defined
payload that is sent to the FW. Since the FW behaves the same no matter
what value we pass to it, we can just write the same thing on all gens
and get rid of the function pointer by saving the register offset.
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217012316.13271-6-daniele.ceraolospurio@intel.com

Since we started using CT buffers on all gens, the function pointers can
only be set to either the _nop() or the _ct() functions. Since the
_nop() case applies to when the CT are disabled, we can just handle that
case in the _ct() functions and call them directly.

v2: keep intel_guc_send() and make the CT send/receive functions work on
    intel_guc_ct. (Michal)
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217012316.13271-5-daniele.ceraolospurio@intel.com

For better isolation of the request tracking from the rest of the
CT-related data.

v2: split to separate patch, move next_fence to substructure (Michal)
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217012316.13271-4-daniele.ceraolospurio@intel.com

The GuC supports having multiple CT buffer pairs and we designed our
implementation with that in mind. However, the different channels are not
processed in parallel within the GuC, so there is very little advantage
in having multiple channels (independent locks?), compared to the
drawbacks (one channel can starve the other if messages keep being
submitted to it). Given this, it is unlikely we'll ever add a second
channel and therefore we can simplify our code by removing the
flexibility.

v2: split substructure grouping to separate patch, improve docs (Michal)
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217012316.13271-3-daniele.ceraolospurio@intel.com

We track the status of the GuC much more closely now and we expect the
enable/disable functions to be correctly called only once. If this isn't
true we do want to flag it as a flow failure (via the BUG_ON in the ctch
functions) and not silently ignore the call.
Suggested-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217012316.13271-2-daniele.ceraolospurio@intel.com

The only difference from the GuC POV between guc_communication_stop and
guc_communication_disable is that the former can be called after GuC
has been reset. Instead of having two separate paths, we can just skip
the call into GuC in the disabling path and re-use that.

Note that by using the disable() path instead of the stop() one there
are two additional changes in SW side for the stop path:

- interrupts are now disabled before disabling the CT, which is ok
  because we do not want interrupts with CT disabled;
- guc_get_mmio_msg() is called in the stop case as well, which is ok
  because if there are errors before the reset we do want to record
  them.
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217012316.13271-1-daniele.ceraolospurio@intel.com

Get_pid_task() needs to be paired with a put_pid or we leak a pid
reference every time a banned client tries to create a context.

v2:
 * task_pid_nr helper exists! (Chris)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: b083a087 ("drm/i915: Add per client max context ban limit")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217170933.8108-1-tvrtko.ursulin@linux.intel.com

As we stash a pointer to the HWSP cacheline on the request, when reading
it we only need confirm that the cacheline is still valid by checking
that the request and timeline are still intact.

v2: Protect hwsp_cachline with RCU
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217011659.3092130-1-chris@chris-wilson.co.uk

Since commit e5dadff4 ("drm/i915: Protect request retirement with
timeline->mutex"), the request retirement can happen outside of the
struct_mutex serialised only by the timeline->mutex. We drop the
timeline->mutex on submitting the request (i915_request_add) so after
that point, it is liable to be freed. Make sure our local reference is
kept alive until we have finished attaching it to the signalers. (Note
that this erodes the argument that i915_request_add should consume the
reference, but that is a slightly larger patch!)

Fixes: e5dadff4 ("drm/i915: Protect request retirement with timeline->mutex")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217134729.3297818-1-chris@chris-wilson.co.uk

At least Bay Trail (BYT) and Cherry Trail (CHT) devices can use 1 of 2
different PWM controllers for controlling the LCD's backlight brightness.
Either the one integrated into the PMIC or the one integrated into the
SoC (the 1st LPSS PWM controller).

So far in the LPSS code on BYT we have skipped registering the LPSS PWM
controller "pwm_backlight" lookup entry when a Crystal Cove PMIC is
present, assuming that in this case the PMIC PWM controller will be used.

On CHT we have been relying on only 1 of the 2 PWM controllers being
enabled in the DSDT at the same time; and always registered the lookup.

So far this has been working, but the correct way to determine which PWM
controller needs to be used is by checking a bit in the VBT table and
recently I've learned about 2 different BYT devices:
Point of View MOBII TAB-P800W
Acer Switch 10 SW5-012

Which use a Crystal Cove PMIC, yet the LCD is connected to the SoC/LPSS
PWM controller (and the VBT correctly indicates this), so here our old
heuristics fail.

This commit fixes using the wrong PWM controller on these devices by
calling pwm_get() for the right PWM controller based on the
VBT dsi.config.pwm_blc bit.

Note this is part of a series which contains 2 other patches which renames
the PWM lookup for the 1st SoC/LPSS PWM from "pwm_backlight" to
"pwm_pmic_backlight" and the PWM lookup for the Crystal Cove PMIC PWM
from "pwm_backlight" to "pwm_pmic_backlight".
Acked-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216202906.1662893-4-hdegoede@redhat.com

Sandybridge is the gen that didn't handle multiple registers in a single
LRI packet. Don't forget it!

Fixes: 902eb748 ("drm/i915/gt: Tidy up full-ppgtt on Ivybridge")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Tested-by: NTomi Sarvela <tomi.p.sarvela@intel.com>
Acked-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217091328.3093551-1-chris@chris-wilson.co.uk

We currently use an error-prone mutex_trylock to grab another timeline
to find an earlier request along it. However, with a bit of a
sleight-of-hand, we can reduce the mutex_trylock to a spin_lock on the
immediate request and careful pointer chasing to acquire a reference on
the previous request.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216165317.2742896-1-chris@chris-wilson.co.uk

Signed-off-by: NMaya Rashish <coypu@sdf.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213102630.GA24082@SDF.ORG

With a couple more memory barriers dotted around the place we can
significantly reduce the MTBF on Ivybridge. Still doesn't really help
Haswell though.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216142409.2605211-1-chris@chris-wilson.co.uk

When creating a handle, it is just that, an abstract handle. The fact
that we cannot currently support a handle larger than the size of the
backing storage is an artifact of our whole-object-at-a-time handling in
get_pages() and being an implementation limitation is best handled at
that point -- similar to shmem, where we only barf when asked to
populate the whole object if larger than RAM. (Pinning the whole object
at a time is major hindrance that we are likely to have to overcome in
the near future.) In the case of the buddy allocator, the late check is
preferable as the request size may often be smaller than the required
size.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216122603.2598155-1-chris@chris-wilson.co.uk

typecheck() macro creates an huge stack size causing
issues with static analysis with coverity, addressing
this with creating a local pointer.

Fixes: 639f2f24 ("drm/i915: Introduce new macros for tracing")
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NVenkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216185332.83289-1-venkata.s.dhanalakota@intel.com

Fixes coccicheck warning:

drivers/gpu/drm/i915/gem/i915_gem_region.c:88:2-3: Unneeded semicolon
drivers/gpu/drm/i915/gvt/gtt.c:1285:2-3: Unneeded semicolon
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: Nzhengbin <zhengbin13@huawei.com>
Acked-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1576467845-60920-1-git-send-email-zhengbin13@huawei.com

In some cases like latency[level]==0, wm[level].res_lines>31,
min_ddb_alloc can be U16_MAX, exclude it from the WARN_ON.

v2: Specify the cases in which we hit U16_MAX, indentation (Ville)

Fixes: 10a7e07b ("drm/i915: Make sure cursor has enough ddb for the selected wm level")
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216080619.10945-1-vandita.kulkarni@intel.com

According to both the old acpi_igd_opregion_spec_0.pdf and the newer
skl_opregion_rev0p5.pdf opregion specification documents, if a driver
handles hotplug events itself, it should set the opregion CHPD field to
1 to indicate this and the firmware should respond to this by no longer
sending ACPI 0x00 notification events on e.g. lid-state changes.

Specifically skl_opregion_rev0p5.pdf states thid in the documentation of
the CHPD word: "Re-enumeration trigger logic in System BIOS MUST be
disabled for all the Operating Systems supporting Hot-Plug
(e.g., Windows* Longhorn and above)." Note the MUST in there.

We ignore these notifications, so this should not be a problem but many
recent DSTDs seem to all have the same copy-pasted bug in the GNOT() AML
function which is used to send these notifications. Windows likely does not
hit this bug as it presumably correcty sets CHPD to 1.

Here is an example of the broken GNOT() method:

            Method (GNOT, 2, NotSerialized)
            {
                ...
                CEVT = Arg0
                CSTS = 0x03
                If (((CHPD == Zero) && (Arg1 == Zero)))
                {
                    If (((OSYS > 0x07D0) || (OSYS < 0x07D6)))
                    {
                        Notify (PCI0, Arg1)
                    }
                    Else
                    {
                        Notify (GFX0, Arg1)
                    }
                }
                ...

Notice that the condition for the If is always true I believe that the
|| like needs to be an &&, but there is nothing we can do about this and
in my own DSDT archive 55 of the 93 DSDTs have this issue.

When the if is true the notification gets send to the PCI root instead
of only to the GFX0 device. This causes Linux to re-enumerate PCI devices
whenever the LID opens / closes, leading to unexpected messages in dmesg:

Suspend through lid close:
[  313.598199] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
[  313.664453] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
[  313.737982] pci_bus 0000:01: Allocating resources
[  313.738036] pcieport 0000:00:1c.0: bridge window [io  0x1000-0x0fff] to [bus 01] add_size 1000
[  313.738051] pcieport 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000 add_align 100000
[  313.738111] pcieport 0000:00:1c.0: BAR 15: assigned [mem 0x91000000-0x911fffff 64bit pref]
[  313.738128] pcieport 0000:00:1c.0: BAR 13: assigned [io  0x1000-0x1fff]

Resume:
[  813.623894] pci 0000:00:03.0: [8086:22b8] type 00 class 0x048000
[  813.623955] pci 0000:00:03.0: reg 0x10: [mem 0x00000000-0x003fffff]
[  813.630477] pci 0000:00:03.0: BAR 0: assigned [mem 0x91c00000-0x91ffffff]
[  854.579101] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3

And more importantly this re-enumeration races with suspend/resume causing
enumeration to not be complete  when assert_isp_power_gated() from
drivers/gpu/drm/i915/display/intel_display_power.c runs. This causes
the !pci_dev_present(isp_ids) check in assert_isp_power_gated() to fail
making the condition for the WARN true, leading to:

[  813.327886] ------------[ cut here ]------------
[  813.327898] ISP not power gated
[  813.328028] WARNING: CPU: 2 PID: 2317 at drivers/gpu/drm/i915/display/intel_display_power.c:4870 intel_display_print_error_state+0x2b98/0x3a80 [i915]
...
[  813.328599] ---[ end trace f01e81b599596774 ]---

This commit fixes the unwanted ACPI notification on the PCI root device
by setting CHPD to 1, so that the broken if condition in the AML never
gets checked as notifications of type 0x00 are disabled altogether.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212204828.191288-1-hdegoede@redhat.com

Wait for the object to be idle before changing its cache-level and
unbinding. This was dropped as supposedly superfluous from commit
8b1c78e0 ("drm/i915: Avoid calling i915_gem_object_unbind holding
object lock"), but it turns out to prevent some cache dirt escaping.
Smells like papering over a race...

Closes: https://gitlab.freedesktop.org/drm/intel/issues/820
Fixes: 8b1c78e0 ("drm/i915: Avoid calling i915_gem_object_unbind holding object lock")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Acked-by: NAndi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213223140.1830738-1-chris@chris-wilson.co.uk

Commit 4d89adc7 ("drm/i915/display/dsi: Add support to pipe D")
added pipe D support for DSI, but failed to update the state readout.

Fixes: 4d89adc7 ("drm/i915/display/dsi: Add support to pipe D")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191211110844.2996-1-jani.nikula@intel.com

Just like in commit 523e0cc8 ("drm/i915/tgl: allow DVI/HDMI on port
A"), the port checks when reading the VBT can easily not match what the
platform really exposes. However here we only have some additional debug
messages that are not adding much value: in the previous debug message
we already print everything we know about the VBT.

Instead of keep fixing the possible port assignments according to the
platform, just nuke the additional messages.
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191206190552.8818-1-lucas.demarchi@intel.com

Add two helpers that for reading the actual GT's frequency. The
two helpers are:

 - intel_rps_read_cagf: reads the frequency and returns it not
   normalized

 - intel_rps_read_actual_frequency: provides the frequency in Hz.

Use the above helpers in sysfs and debugfs.
Signed-off-by: NAndi Shyti <andi.shyti@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213183736.31992-2-andi@etezian.org

While not good behaviour, it is, however, established behaviour that we
can punt EAGAIN to userspace if we need to retry the ioctl. When trying
to acquire a mutex, prefer to use EAGAIN to propagate losing the race
so that if it does end up back in userspace, we try again.

Fixes: c81471f5 ("drm/i915: Copy across scheduler behaviour flags across submit fences")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/800Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213160347.1789004-1-chris@chris-wilson.co.uk

New macros ENGINE_TRACE(), CE_TRACE(), RQ_TRACE() and
GT_TRACE() are introduce to tag device name and engine
name with contexts and requests tracing in i915.

Cc: Sudeep Dutt <sudeep.dutt@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NVenkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213155152.69182-2-venkata.s.dhanalakota@intel.com

We do not require to register the sysctl paths per instance,
so making registration global.

v2: make sysctl path register and unregister function driver
    specific (Tvrtko and Lucas).

Cc: Sudeep Dutt <sudeep.dutt@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NVenkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213155152.69182-1-venkata.s.dhanalakota@intel.com