This patch (as1577) adds hrtimer support for unlinking interrupt QHs
in ehci-hcd.  The current code relies on a fixed delay of either 2 or
55 us, which is not always adequate and in any case is totally bogus.
Thanks to internal caching, the EHCI hardware may continue to access
an interrupt QH for more than a millisecond after it has been unlinked.

In fact, the EHCI spec doesn't say how long to wait before using an
unlinked interrupt QH.  The patch sets the delay to 9 microframes
minimum, which ought to be adequate.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1576) adds hrtimer support for managing ehci-hcd's
async schedule.  Just as with the earlier change to the periodic
schedule management, two new hrtimer events take care of everything.

One event polls at 1-ms intervals to see when the Asynchronous
Schedule Status (ASS) flag matches the Asynchronous Schedule Enable
(ASE) value; the schedule's state must not be changed until it does.
The other event delays for 15 ms after the async schedule becomes
empty before turning it off.

The new events replace a busy-wait poll and a kernel timer usage.
They also replace the rather illogical method currently used for
indicating the async schedule should be turned off: attempting to
unlink the dedicated QH at the head of the async list.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1575) removes special code added for status polling of
the EHCI controller in PS3 systems.  While the controller is running,
the polling is now carried out by an hrtimer handler.  When the
controller is suspending or stopping, we use the same polling routine
as the old code -- but in neither case do we need to conclude that the
controller has died if the polling goes on for too long.

As a result the entire handshake_on_error_set_halt() routine is now
unused, so it is removed from the driver.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1574) changes the return type of multiple functions in
ehci-sched.c from int to void.  The values they return are now always
0, so there's no reason for them to return any value at all.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1573) adds hrtimer support for managing ehci-hcd's
periodic schedule.  There are two issues to deal with.

First, the schedule's state (on or off) must not be changed until the
hardware status has caught up with the current command.  This is
handled by an hrtimer event that polls at 1-ms intervals to see when
the Periodic Schedule Status (PSS) flag matches the Periodic Schedule
Enable (PSE) value.

Second, the schedule should not be turned off as soon as it becomes
empty.  Turning the schedule on and off takes time, so we want to wait
until the schedule has been empty for a suitable period before turning
it off.  This is handled by an hrtimer event that gets set to expire
10 ms after the periodic schedule becomes empty.

The existing code polls (for up to 1125 us and with interrupts
disabled!) to check the status, and doesn't implement a delay before
turning off the schedule.  Furthermore, if the polling fails then the
driver decides that the controller has died.  This has caused problems
for several people; some controllers can take 10 ms or more to turn
off their periodic schedules.

This patch fixes these issues.  It also makes the "broken_periodic"
workaround unnecessary; there is no longer any danger of turning off
the periodic schedule after it has been on for less than 1 ms.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1572) begins the conversion of ehci-hcd over to using
high-resolution timers rather than old-fashioned low-resolution kernel
timers.  This reduces overhead caused by timer roundoff on systems
where HZ is smaller than 1000.  Also, the new timer framework
introduced here is much more logical and easily extended than the
ad-hoc approach ehci-hcd currently uses for timers.

An hrtimer structure is added to ehci_hcd, along with a bitflag array
and an array of ktime_t values, to keep track of which timing events
are pending and what their expiration times are.

Only the infrastructure for the timing operations is added in this
patch.  Later patches will add routines for handling each of the
various timing events the driver needs.  In some cases the new hrtimer
handlers will replace the existing handlers for ehci-hcd's kernel
timers; as this happens the old timers will be removed.  In other
cases the new timing events will replace busy-wait loops.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1571) adds a new state for ehci-hcd's root hubs:
EHCI_RH_STOPPING.  This value is used at times when the root hub is
being stopped and we don't know whether or not the hardware has
finished all its DMA yet.

Although the purpose may not be apparent, this distinction will come
in useful later on.  Future patches will avoid actions that depend on
the root hub being operational (like turning on the async or periodic
schedules) when they see the state is EHCI_RH_STOPPING.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1570) adds a pointer for the end of ehci-hcd's
async-unlink list.  The list (which is actually a queue) is singly
linked, so having a pointer to its end makes adding new entries easier
-- there's no longer any need to scan through the whole list.

In principle it could be changed to a standard doubly-linked list.  It
turns out that doing so actually makes the code less clear, so I'm
leaving it as is.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1569) renames the ehci->reclaim list in ehci-hcd.  The
word "reclaim" is used in the EHCI specification to mean something
quite different, and "unlink_next" is more descriptive of the list's
purpose anyway.

Similarly, the "reclaim" field in the ehci_stats structure is renamed
"iaa", which is more meaningful (to experts, anyway) and is a better
match for the "lost_iaa" field.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1568) introduces symbolic constants for some of the
less-frequently used bitfields in the QH structure.  This makes the
code a little easier to read and understand.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1567) removes ehci-hcd's reference counting of QH
structures.  It's not necessary to refcount these things because they
always get deallocated at exactly one spot in ehci_endpoint_disable()
(except for two special QHs, ehci->async and ehci->dummy) and are
never used again.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1566) removes the code in ehci-hcd's resume routines
which tries to restart or cancel any transfers left active while the
root hub or controller was asleep.  This code isn't necessary, because
all URBs are terminated before the root hub is suspended.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently, EHCI initialization turns off the controller (in case it
was left running by the firmware) before setting up the ehci_hcd data
structure.  This patch (as1565) reverses that order.

Although it doesn't matter now, it will matter later on when future
additions to ehci_halt() will want to acquire a spinlock that gets
initialized by ehci_init().
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Update information of Seagate Portable HDD and WD My Passport HDD in
quirk list.
Signed-off-by: NNamjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: NPankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: NAmit Sahrawat <a.sahrawat@samsung.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for write cache quirk on usb hdd. scsi driver will be set to wce
by detecting write cache quirk in quirk list when plugging usb hdd.
Signed-off-by: NNamjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: NPankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: NAmit Sahrawat <a.sahrawat@samsung.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make use of USB quirk method to identify such HDD while reading
the cache status in sd_probe(). If cache quirk is present for
the HDD, lets assume that cache is enabled and make WCE bit
equal to 1.
Signed-off-by: NNamjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: NPankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: NAmit Sahrawat <a.sahrawat@samsung.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The idr_pre_get() function never returns a value < 0.  It returns 0 (no
memory) or 1 (OK).
Reported-by: NSilva Paulo <psdasilva@yahoo.com>
[ Rewrote Silva's patch, but attributing it to Silva anyway  - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixes a problem that can occur when a lone package object is
wrapped with an outer package object in order to conform to
the ACPI specification. Can affect these predefined names:
_ALR,_MLS,_PSS,_TRT,_TSS,_PRT,_HPX,_DLM,_CSD,_PSD,_TSD

https://bugzilla.kernel.org/show_bug.cgi?id=44171

This problem was introduced in 3.4-rc1 by commit
6a99b1c9
(ACPICA: Object repair code: Support to add Package wrappers)
Reported-by: NVlastimil Babka <caster@gentoo.org>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Cc: <stable@vger.kernel.org> # 3.4
Signed-off-by: NLen Brown <len.brown@intel.com>

I couldn't find the vendor ID in any of the online databases, but this
mat has a Pump It Up logo on the top side of the controller compartment,
and a disclaimer stating that Andamiro will not be liable on the bottom.
Signed-off-by: NYuri Khan <yurivkhan@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

We were accidentally losing one bit in the configuration register on
device initialization. It was reported to freeze one specific system
right away. Properly preserve all bits we don't explicitly want to
change in order to prevent that.
Reported-by: NStevie Trujillo <stevie.trujillo@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>

Commit d640113f introduced a regression on SMP
systems where the processor core with ACPI id zero is disabled
(typically should be the case because of hyperthreading).
The regression got spread through stable kernels.
On 3.0.X it got introduced via 3.0.18.

Such platforms may be rare, but do exist.
Look out for a disabled processor with acpi_id 0 in dmesg:
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x10] disabled)

This problem has been observed on a:
HP Proliant BL280c G6 blade

This patch restricts the introduced workaround to platforms
with nr_cpu_ids <= 1.
Signed-off-by: NThomas Renninger <trenn@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Requesting a threaded interrupt without a primary handler and without
IRQF_ONESHOT is dangerous, and after commit 1c6c6952 ("genirq: Reject
bogus threaded irq requests"), these requests are rejected.  This causes
->probe() to fail, and the RTC driver not to be availble.

To fix, add IRQF_ONESHOT to the IRQ flags.

Tested on OMAP3730/OveroSTORM and OMAP4430/Panda board using rtcwake to
wake from system suspend multiple times.
Signed-off-by: NKevin Hilman <khilman@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The code here has a nested spin_lock_irqsave().  It's not needed since
IRQs are already disabled and it causes a problem because it means that
IRQs won't be enabled again at the end.  The second call to
spin_lock_irqsave() will overwrite the value of irq_flags and we can't
restore the proper settings.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NRobin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixes

  WARNING: at irq/handle.c:146 handle_irq_event_percpu+0x19c/0x1b8()
  irq 25 handler mxc_rtc_interrupt+0x0/0xac enabled interrupts
  Modules linked in:
   (unwind_backtrace+0x0/0xf0) from (warn_slowpath_common+0x4c/0x64)
   (warn_slowpath_common+0x4c/0x64) from (warn_slowpath_fmt+0x30/0x40)
   (warn_slowpath_fmt+0x30/0x40) from (handle_irq_event_percpu+0x19c/0x1b8)
   (handle_irq_event_percpu+0x19c/0x1b8) from (handle_irq_event+0x28/0x38)
   (handle_irq_event+0x28/0x38) from (handle_level_irq+0x80/0xc4)
   (handle_level_irq+0x80/0xc4) from (generic_handle_irq+0x24/0x38)
   (generic_handle_irq+0x24/0x38) from (handle_IRQ+0x30/0x84)
   (handle_IRQ+0x30/0x84) from (avic_handle_irq+0x2c/0x4c)
   (avic_handle_irq+0x2c/0x4c) from (__irq_svc+0x40/0x60)
  Exception stack(0xc050bf60 to 0xc050bfa8)
  bf60: 00000001 00000000 003c4208 c0018e20 c050a000 c050a000 c054a4c8 c050a000
  bf80: c05157a8 4117b363 80503bb4 00000000 01000000 c050bfa8 c0018e2c c000e808
  bfa0: 60000013 ffffffff
   (__irq_svc+0x40/0x60) from (default_idle+0x1c/0x30)
   (default_idle+0x1c/0x30) from (cpu_idle+0x68/0xa8)
   (cpu_idle+0x68/0xa8) from (start_kernel+0x22c/0x26c)
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Without this patch, if Device Tree is enabled the AB8500 RTC wouldn't get
probed at all, as there is no reference to it from platform code.  This
patch ensures the driver is probed during normal DT start-up.

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This driver's IRQ registration is failing because the kernel now forces
IRQs to be ONESHOT if no IRQ handler is passed.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

`config' is freed and is then used in the rtc_device_unregister() call,
causing a kernel panic.
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Reviewed-by: NViresh Kumar <viresh.linux@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Do not use MX2_CAMERA_SWAP16 and MX2_CAMERA_PACK_DIR_MSB flags. The driver
must negotiate with the attached sensor whether the mbus format is UYUV or
YUYV and set CSICR1 configuration accordingly.

This is needed for the video function on mach-imx27_visstrim_m10.c to
perform properly, since an earlier version of this patch has been proven
wrong and has been reverted and a commit, depending on it: "[media]
i.MX27: visstrim_m10: Remove use of MX2_CAMERA_SWAP16" is in the mainline.
Signed-off-by: NJavier Martin <javier.martin@vista-silicon.com>
Reviewed-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
[ g.liakhovetski@gmx.de: move a macro definition to a more logical place ]
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
[ Applying directly because Mauro is on vacation - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NIlia Katsnelson <k0009000@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The device should be handled by xpad driver instead of generic HID driver.
Signed-off-by: NYuri Khan <yurivkhan@gmail.com>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Fix a boot regression on Mackerel boards with sh_mobile_sdhi
in existing kernels causing:

genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq XXX

caused by 1c6c6952 (genirq: Reject bogus threaded irq requests).

This is backported from Guennadi's patch:
"mmc: extend and rename cd-gpio helpers to handle more slot GPIO functions"
Reported-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This reverts commit 3d93576e(skip card initialization if
power class selection fails).
Problem has been reported when this is used with eMMC4.41
card with Tegra Platform. Till the issue is root caused,
bus width selection failure should not be treated as fatal.
Reported-by: NMarc Dietrich <marvin24@gmx.de>
Signed-Off-by: NVenkatraman S <svenkatr@ti.com>
CC: Ulf Hansson <ulf.hansson@stericsson.com>
CC: Subhash Jadavani <subhashj@codeaurora.org>
CC: Saugata Das <saugata.das@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

commit 626f9914 added code to initialize gpio_chip.of_node, but if
CONFIG_OF_GPIO is not defined gps-tps65910 fails to build with an
error complaining gpio_chip has no member of_node. I ran into this
while doing a allyesconfig build on linux-next.
Signed-off-by: NGerard Snitselaar <dev@snitselaar.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This is an old suspend/resume lockup fix:

	commit 2780cc4660e1
	Author: Len Brown <len.brown@intel.com>
	Date:   Thu Dec 23 13:43:30 2004 -0500

	    [ACPI] Fix suspend/resume lockup issue
	    by leaving Bus Master Arbitration enabled.
	    The ACPI spec mandates it be disabled only for C3.

	    http://bugzilla.kernel.org/show_bug.cgi?id=3599Signed-off-by: NDavid Shaohua Li <shaohua.li@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The bug snuck back in in commit 2feec47d (ACPICA: ACPI 5: Support
for new FADT SleepStatus, SleepControl registers, 2012-02-14),
presumably by copy/pasting a copy of the code without that fix for the
legacy case.

On affected machines, after that commit, the machine locks up hard on
resume from suspend.  The same fix as seven years ago still works.

Addresses <https://bugzilla.kernel.org/show_bug.cgi?id=43641>.
Reported-bisected-and-tested-by: NOctavio Alvarez <alvarezp@alvarezp.com>
Reported-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NJonathan Nieder <jrnieder@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

This reverts commit 107a84e6.

Meelis Roos reports a regression since 3.5-rc5 that stops Sun Fire V100
and Sun Netra X1 sparc64 machines from booting, hanging after enabling
serial console.  He bisected it to commit 107a84e6.

Rob Herring explains:
 "The problem is match combinations of compatible plus name and/or type
  fail to match correctly.  I have a fix for this, but given how late it
  is for 3.5 I think it is best to revert this for now.  There could be
  other cases that rely on the current although wrong behavior.  I will
  post an updated version for 3.6."
Bisected-and-reported-by: NMeelis Roos <mroos@linux.ee>
Requested-by: NRob Herring <rob.herring@calxeda.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

when the default irq quick handler is used then IRQF_ONESHOT must be set
otherwise the request fails and following error is displayed:

mei 0000:00:16.0: irq 48 for MSI/MSI-X
genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq 48
mei 0000:00:16.0: request_threaded_irq failed: irq = 48.
dpm_run_callback(): pci_pm_resume+0x0/0x140 returns -22
PM: Device 0000:00:16.0 failed to resume async: error -22
Reported-by: NPeter Wu <lekensteyn@gmail.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Tested-by: NPeter Wu <lekensteyn@gmail.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Quite a few ASUS computers experience a nasty problem, related to the
EHCI controllers, when going into system suspend.  It was observed
that the problem didn't occur if the controllers were not put into the
D3 power state before starting the suspend, and commit
151b6128 (USB: EHCI: fix crash during
suspend on ASUS computers) was created to do this.

It turned out this approach messed up other computers that didn't have
the problem -- it prevented USB wakeup from working.  Consequently
commit c2fb8a3f (USB: add
NO_D3_DURING_SLEEP flag and revert 151b6128) was merged; it
reverted the earlier commit and added a whitelist of known good board
names.

Now we know the actual cause of the problem.  Thanks to AceLan Kao for
tracking it down.

According to him, an engineer at ASUS explained that some of their
BIOSes contain a bug that was added in an attempt to work around a
problem in early versions of Windows.  When the computer goes into S3
suspend, the BIOS tries to verify that the EHCI controllers were first
quiesced by the OS.  Nothing's wrong with this, but the BIOS does it
by checking that the PCI COMMAND registers contain 0 without checking
the controllers' power state.  If the register isn't 0, the BIOS
assumes the controller needs to be quiesced and tries to do so.  This
involves making various MMIO accesses to the controller, which don't
work very well if the controller is already in D3.  The end result is
a system hang or memory corruption.

Since the value in the PCI COMMAND register doesn't matter once the
controller has been suspended, and since the value will be restored
anyway when the controller is resumed, we can work around the BIOS bug
simply by setting the register to 0 during system suspend.  This patch
(as1590) does so and also reverts the second commit mentioned above,
which is now unnecessary.

In theory we could do this for every PCI device.  However to avoid
introducing new problems, the patch restricts itself to EHCI host
controllers.

Finally the affected systems can suspend with USB wakeup working
properly.

Reference: https://bugzilla.kernel.org/show_bug.cgi?id=37632
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=42728Based-on-patch-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NDâniel Fraga <fragabr@gmail.com>
Tested-by: NJavier Marcet <jmarcet@gmail.com>
Tested-by: NAndrey Rahmatullin <wrar@wrar.name>
Tested-by: NOleksij Rempel <bug-track@fisher-privat.net>
Tested-by: NPavel Pisa <pisa@cmp.felk.cvut.cz>
Cc: stable <stable@vger.kernel.org>
Acked-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for the 15'' MacBook Pro Retina model (MacBookPro10,1).

Patch originally written by clipcarl (forums.opensuse.org).
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add support for the 15'' MacBook Pro Retina. The keyboard is
the same as recent models.

The patch needs to be synchronized with the bcm5974 patch for
the trackpad - as usual.

Patch originally written by clipcarl (forums.opensuse.org).

[rydberg@euromail.se: Amended mouse ignore lines]
Signed-off-by: NRyan Bourgeois <bluedragonx@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

udbg_init_debug_opal() should be udbg_init_debug_opal_raw() as
the caller in arch/powerpc/kernel/udbg.c expects
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>