nic_data was already initialised to the right thing, no need to assign
it again.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TX size bins were not supported on the 7000's 40G MAC, but the 8000 series
does support them and the MCPU advertises that via a new capability bit.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Richard Alpe says:

====================
tipc: introduce UDP replicast

This series introduces UDP replicast. A concept where we emulate multicast by
sending multiple unicast messages to configured peers. This allows TIPC to be
used in environments where IP multicast is disabled.

There is a corresponding patch series for the tipc user space tool that
allows a user to add remote addresses to the replicast list.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using replicast a UDP bearer can have an arbitrary amount of
remote ip addresses associated with it. This means we cannot simply
add all remote ip addresses to an existing bearer data message as it
might fill the message, leaving us with a truncated message that we
can't safely resume. To handle this we introduce the new netlink
command TIPC_NL_UDP_GET_REMOTEIP. This command is intended to be
called when the bearer data message has the
TIPC_NLA_UDP_MULTI_REMOTEIP flag set, indicating there are more than
one remote ip (replicast).
Signed-off-by: NRichard Alpe <richard.alpe@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add UDP bearer options to netlink bearer get message. This is used by
the tipc user space tool to display UDP options.

The UDP bearer information is passed using either a sockaddr_in or
sockaddr_in6 structs. This means the user space receiver should
intermediately store the retrieved data in a large enough struct
(sockaddr_strage) before casting to the proper IP version type.
Signed-off-by: NRichard Alpe <richard.alpe@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Automatically learn UDP remote IP addresses of communicating peers by
looking at the source IP address of incoming TIPC link configuration
messages (neighbor discovery).

This makes configuration slightly easier and removes the problematic
scenario where a node receives directly addressed neighbor discovery
messages sent using replicast which the node cannot "reply" to using
mutlicast, leaving the link FSM in a limbo state.
Signed-off-by: NRichard Alpe <richard.alpe@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces UDP replicast. A concept where we emulate
multicast by sending multiple unicast messages to configured peers.

The purpose of replicast is mainly to be able to use TIPC in cloud
environments where IP multicast is disabled. Using replicas to unicast
multicast messages is costly as we have to copy each skb and send the
copies individually.
Signed-off-by: NRichard Alpe <richard.alpe@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a function to check if a tipc UDP media address is a multicast
address or not. This is a purely cosmetic change.
Signed-off-by: NRichard Alpe <richard.alpe@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split the UDP send function into two. One callback that prepares the
skb and one transmit function that sends the skb. This will come in
handy in later patches, when we introduce UDP replicast.
Signed-off-by: NRichard Alpe <richard.alpe@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split the UDP netlink parse function so that it only parses one
netlink attribute at the time. This makes the parse function more
generic and allow future UDP API functions to use it for parsing.
Signed-off-by: NRichard Alpe <richard.alpe@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And while at it, remove the unecessary writing of zeroes to the CPU_MASK_CLEAR
register since it has no functional use.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add tso/tso6 support to the alx driver.
Based on information from the downstream driver at github.com/qca/alx
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nelson Chang says:

====================
net: ethernet: mediatek: modify to use the PDMA for Ethernet RX

This series have some modifications and refines to support Ethernet RX by the PDMA.

changes since v4:
- Remove the redundant OR operation in mtk_hw_init()

changes since v3:
- Add GDM hardware settings to send packets to PDMA for RX

changes since v2:
- Fix the bugs of PDMA cpu index and interrupt settings in mtk_poll_rx()

changes since v1:
- Modify to use the PDMA instead of the QDMA for Ethernet RX
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because we change to use the PDMA as the Ethernet RX DMA engine,
the patch modifies to set GDM to send packets to PDMA for RX.
Acked-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NNelson Chang <nelson.chang@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because the PDMA has richer features than the QDMA for Ethernet RX
(such as multiple RX rings, HW LRO, etc.),
the patch modifies to use the PDMA to handle Ethernet RX.
Acked-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NNelson Chang <nelson.chang@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: Make bcm_sf2 utilize b53_common

This patch series makes the bcm_sf2 driver utilize a large number of the core
functions offered by the b53_common driver since the SWITCH_CORE registers are
mostly register compatible with the switches driven by b53_common.

In order to accomplish that, we just override the dsa_driver_ops callbacks that
we need to. There are still integration specific logic from the bcm_sf2 that we
cannot absorb into b53_common because it is just not there, mostly in the area
of link management and power management, but most of the features are within
b53_common now: VLAN, FDB, bridge

Along the process, we also improve support for the BCM58xx SoCs, since those
also have the same version of the switching IP that 7445 has (for which bcm_sf2
was developed).

Changes in v3:

- rebase against 145dd5f9 ("net: flush the
  softnet backlog in process context")

Changes in v2:

- rebased against "net: dsa: rename switch operations structure"
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we are using b53_common for most VLAN, FDB and bridge
operations, delete all the redundant code that we had in bcm_sf2.c to
keep only the integration specific logic that we have to deal with:
power management, link management and the external interfaces (RGMII,
MDIO).
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Broadcom Starfighter2 is almost entirely register compatible with
B53, yet for historical reasons came up first in the tree and is now
being updated to utilize b53_common.c to the fullest extent possible. A
few things need to be adjusted to allow that:

- the switch "core" registers currently operate on a 32-bit address,
  whereas b53 passes a page + reg pair to offset from, so we need to
  convert that, thankfully there is a generic formula to do that

- the link managemenent is not self contained with the B53/CORE register
  set, but instead is in the SWITCH_REG block which is part of the
  integration glue logic, so we keep that entirely custom here because
  this really is part of the existing bcm_sf2 implementation

- there are additional power management constraints on the port's
  memories that make us keep the port_enable/disable callbacks custom
  for now, also, we support tagging whereas b53_common does not support
  that yet

All the VLAN and bridge code is entirely identical though so, avoid
duplicating it. Other things will be migrated in the future like EEE and
possibly Wake-on-LAN.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to migrate the bcm_sf2 driver over to the b53 driver for most
VLAN/FDB/bridge operations, we need to add support for the "join all
VLANs" register and behavior which allows us to make a given port join
all VLANs and avoid setting specific VLAN entries when it is leaving the
bridge.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 58xx and 7445 chips use the Starfighter2 code, define its MIB layout
and introduce a helper function: is58xx() which checks for both of these
IDs for now.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate a device entry for the Broadcom BCM7445 integrated switch
currently backed by bcm_sf2.c. Since this is the latest generation, it
has 4 ARL entries, 4K VLANs and uses Port 8 for the CPU/IMP port.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to allow drivers to override specific dsa_switch_driver
callbacks, initialize ds->ops to b53_switch_ops earlier, which avoids
having to expose this structure to glue drivers.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Introduce support for offload forward mark

Ido says:
This patchset enables the forwarding of certain control packets by the
device instead of relying on the CPU to do the forwarding.

The first two patches simplify the current switchdev offload forward
infrastructure and make it usable for stacked devices. This is done by
moving the packet and port marking to the bridge driver instead of the
switch driver.

Patches 3-5 add the mlxsw specific bits to support the forward mark.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of trapping certain packets to the CPU and then relying on it to
flood them we can instead make the device mirror them.

The following packet types are mirrored:

* DHCP: Broadcast packets that should be flooded by the device, but also
trapped in case CPU is running the DHCP server.

* IGMP query: Multicast packets that need to be forwarded to other
bridge ports, but also trapped so that receiving netdev will be marked
as a router port by the bridge driver.

* ARP request: Broadcast packets that should be forwarded to other
bridge ports, but also trapped in case requested IP is of the local
machine.

* ARP response: Unicast packets that should be forwarded by the bridge
but also trapped in case response is directed at us.

Set the trap action of such packets to mirror and mark them using
'offload_fwd_mark' to prevent the bridge driver from forwarding them
itself.

Note that OSPF packets are also marked despite their action being trap.
The reason for this is that the device traps such packets in the
pipeline after they were already flooded.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Up until now we only trapped packets to CPU, but we are going to allow
some packets to be mirrored (trap & forward) to CPU.

Extend the Rx listener with 'action' member.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of copying & pasting the same struct initialization for every
Rx listener, just use a macro.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of
port netdevs so that packets being flooded by the device won't be
flooded twice.

It works by assigning a unique identifier (the ifindex of the first
bridge port) to bridge ports sharing the same parent ID. This prevents
packets from being flooded twice by the same switch, but will flood
packets through bridge ports belonging to a different switch.

This method is problematic when stacked devices are taken into account,
such as VLANs. In such cases, a physical port netdev can have upper
devices being members in two different bridges, thus requiring two
different 'offload_fwd_mark's to be configured on the port netdev, which
is impossible.

The main problem is that packet and netdev marking is performed at the
physical netdev level, whereas flooding occurs between bridge ports,
which are not necessarily port netdevs.

Instead, packet and netdev marking should really be done in the bridge
driver with the switch driver only telling it which packets it already
forwarded. The bridge driver will mark such packets using the mark
assigned to the ingress bridge port and will prevent the packet from
being forwarded through any bridge port sharing the same mark (i.e.
having the same parent ID).

Remove the current switchdev 'offload_fwd_mark' implementation and
instead implement the proposed method. In addition, make rocker - the
sole user of the mark - use the proposed method.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

switchdev_port_same_parent_id() currently expects port netdevs, but we
need it to support stacked devices in the next patch, so drop the
NO_RECURSE flag.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unused and useless priv_size member from struct devlink_ops.

Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently in process_backlog(), the process_queue dequeuing is
performed with local IRQ disabled, to protect against
flush_backlog(), which runs in hard IRQ context.

This patch moves the flush operation to a work queue and runs the
callback with bottom half disabled to protect the process_queue
against dequeuing.
Since process_queue is now always manipulated in bottom half context,
the irq disable/enable pair around the dequeue operation are removed.

To keep the flush time as low as possible, the flush
works are scheduled on all online cpu simultaneously, using the
high priority work-queue and statically allocated, per cpu,
work structs.

Overall this change increases the time required to destroy a device
to improve slightly the packets reinjection performances.
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When I added support to export the vlan entry flags via xstats I forgot to
add support for the pvid since it is manually matched, so check if the
entry matches the vlan_group's pvid and set the flag appropriately.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit b17c7069 ("loopback: sctp: add NETIF_F_SCTP_CSUM to device
features") added NETIF_F_SCTP_CRC to device features for lo device to
improve the performance of sctp over lo.

This patch is to add NETIF_F_SCTP_CRC to device features for veth to
improve the performance of sctp over veth.

Before this patch:
  ip netns exec cs_client netperf -H 10.167.12.2 -t SCTP_STREAM -- -m 10K
  Recv   Send    Send
  Socket Socket  Message  Elapsed
  Size   Size    Size     Time     Throughput
  bytes  bytes   bytes    secs.    10^6bits/sec

  212992 212992  10240    10.00    1117.16

After this patch:
  ip netns exec cs_client netperf -H 10.167.12.2 -t SCTP_STREAM -- -m 10K
  Recv   Send    Send
  Socket Socket  Message  Elapsed
  Size   Size    Size     Time     Throughput
  bytes  bytes   bytes    secs.    10^6bits/sec

  212992 212992  10240    10.20    1415.22
Tested-by: NLi Shuang <tjlishuang@yeah.net>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we keep shadow copies of which interrupt sources are enabled
through the intrl2_*_mask_{set,clear} macros, make sure that the
ordering in which we do these two operations: update the copy, then
unmask the register is correct.

This is not currently a problem because we actually do not use them, but
we will in a subsequent patch optimizing register accesses, so better be
safe here.

Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

per_cpu_inc() is faster (at least on x86) than per_cpu_ptr(xxx)++;
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds SNMP counter for drops caused by MD5 mismatches.

The current syslog might help, but a counter is more precise and helps
monitoring.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TCP MD5 mismatches do increment sk_drops counter in all states but
SYN_RECV.

This is very unlikely to happen in the real world, but worth adding
to help diagnostics.

We increase the parent (listener) sk_drops.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following sparse warning:

drivers/net/vmxnet3/vmxnet3_drv.c:1645:1: warning:
 symbol 'vmxnet3_rq_destroy_all_rxdataring' was not declared. Should it be static?
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NShrikrishna Khare <skhare@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return error code -ENOMEM from the dma_map_single error
handling case instead of 0, as done elsewhere in this function.

Fixes: 032c5e82 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove an open coded simple_open() function and replace file
operations references to the function with simple_open()
instead.

Generated by: scripts/coccinelle/api/simple_open.cocci
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows a privileged process to filter by socket mark when
dumping sockets via INET_DIAG_BY_FAMILY. This is useful on
systems that use mark-based routing such as Android.

The ability to filter socket marks requires CAP_NET_ADMIN, which
is consistent with other privileged operations allowed by the
SOCK_DIAG interface such as the ability to destroy sockets and
the ability to inspect BPF filters attached to packet sockets.

Tested: https://android-review.googlesource.com/261350Signed-off-by: NLorenzo Colitti <lorenzo@google.com>
Acked-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>