This patch adds support for configuring the RGMII skew delays in Rx and
Tx. The Rx and Tx skews are set based on the interface mode. By default
their configuration is set to the default value in hardware (0.2ns);
this means the driver do not rely anymore on the bootloader
configuration.

Then based on the interface mode being used, a 2ns delay is added:
- RGMII_ID adds it for both Rx and Tx.
- RGMII_RXID adds it for Rx.
- RGMII_TXID adds it for Tx.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for connecting VSC8584 PHYs to the MAC using
RGMII.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Offload action skbedit priority when keyed to a flower classifier. The
skb->priority field in Linux is very generic, so only allow setting the
bottom 8 priorities and bounce anything else.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The QOS_ACTION is used for manipulating the QoS attributes of a packet.
Add the corresponding defines and helpers, in particular for the
switch_priority override.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

it will check the return value of dwmac_dma_reset() in the
stmmac_init_dma_engine() function and report an error if the
return value is not zero. so don't need check here.
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit a5afc167 ("net: phy: mscc: add support for VSC8584 PHY")
introduced a call to 'phy_write' storing its return value to a variable
called 'ret'. But 'ret' never was checked for a possible error being
returned, and hence was not used at all. Fix this by checking the return
value and exiting the function if an error was returned.

As this does not fix a known bug, this commit is mostly cosmetic and not
sent as a fix.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove including <linux/version.h> that don't need it.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'octeon_chip_specific_setup':
drivers/net/ethernet/cavium/liquidio/lio_main.c:1378:8: warning:
 variable 's' set but not used [-Wunused-but-set-variable]

It's not used since commit b6334be6 ("net/liquidio: Delete driver version assignment")
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At least some integrated PHY's in RTL8168/RTL8125 chip versions support
downshift, and the actual link speed can be read from a vendor-specific
register. Info about this register was provided by Realtek.
More details about downshift configuration (e.g. number of attempts)
aren't available, therefore the downshift tunable is not implemented.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement occupancy counting for counters and expose over devlink
resource API.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Put all init operations related to subpools into
mlxsw_sp_counter_sub_pools_init().
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the validation of subpools configuration, to avoid possible over
commitment to resource registration. Add WARN_ON to indicate bug
in the code.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement devlink resources support for counter pools. Move the subpool
sizes calculations into the new resources register function.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new field to subpool struct that would indicate which
resource id should be used to query the entry size for
the subpool from the device.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the global static array of subpools is used. Make it
per-instance as multiple instances of the mlxsw driver can have
different values.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bank size is different between Spectrum versions. Also it is
a resource that can be queried. So instead of hard coding the value in
code, query it from the firmware.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Chelsio NICs have 3 filter regions, in following order of priority:
1. High Priority (HPFILTER) region (Highest Priority).
2. HASH region.
3. Normal FILTER region (Lowest Priority).

Currently, there's a 1-to-1 mapping between the prio value passed
by TC and the filter region index. However, it's possible to have
multiple TC rules with the same prio value. In this case, if a region
is exhausted, no attempt is made to try inserting the rule in the
next available region.

So, rework and remove the 1-to-1 mapping. Instead, dynamically select
the region to insert the filter rule, as long as the new rule's prio
value doesn't conflict with existing rules across all the 3 regions.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To check whether a netdevice has already been registered, look at
NETREG_REGISTERED to replace some hacks I added a while ago.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qeth_do_ioctl() is only reached through our own net_device_ops, so we
can trust that dev->ml_priv still contains what we put there earlier.

qeth_bridgeport_an_set() is an internal function that doesn't require
such sanity checks.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Data addresses in the AOB are absolute, and need to be translated before
being fed into kmem_cache_free(). Currently this phys_to_virt() is a no-op.
Also see commit 2db01da8 ("s390/qdio: fill SBALEs with absolute addresses").
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Versions are meaningless for an in-kernel driver.
Instead use the UTS_RELEASE that is set by ethtool_get_drvinfo().

Cc: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for SOF_TIMESTAMPING_TX_SOFTWARE.
No support for non-IQD devices, since they orphan the skb in their xmit
path.

To play nice with TX bulking, set the timestamp when the buffer that
contains the skb(s) is actually flushed out to HW.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For ucast traffic, qeth_iqd_select_queue() falls back to
netdev_pick_tx(). This will potentially use skb_tx_hash() to distribute
the flow over all active TX queues - so txq 0 is a valid selection, and
qeth_iqd_select_queue() needs to check for this and put it on some other
queue. As a result, the distribution for ucast flows is unbalanced and
hits QETH_IQD_MIN_UCAST_TXQ heavier than the other queues.

Open-coding a custom variant of skb_tx_hash() isn't an option, since
netdev_pick_tx() also gives us eg. access to XPS. But we can pull a
little trick: add a single TC class that excludes the mcast txq, and
thus encourage skb_tx_hash() to not pick the mcast txq.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to the support for z/VM NICs, but we need to take extra care
about the dedicated mcast queue:

1. netdev_pick_tx() is unaware of this limitation and might select the
   mcast txq. Catch this.
2. require at least _two_ TX queues - one for ucast, one for mcast.
3. when reducing the number of TX queues, there's a potential race
   where netdev_cap_txqueue() over-rules the selected txq index and
   falls back to index 0. This would place ucast traffic on the mcast
   queue, and result in TX errors.
   So for IQD, reject a reduction while the interface is running.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for ETHTOOL_SCHANNELS to change the count of active
TX queues.

Since all TX queue structs are pre-allocated and -registered, we just
need to trivially adjust dev->real_num_tx_queues.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

z/VM NICs don't offer HW QoS for TX rings. So just use netdev_pick_tx()
to distribute the connections equally over all enabled TX queues.

We start with just 1 enabled TX queue (this matches the typical
configuration without prio-queueing). A follow-on patch will allow users
to enable additional TX queues.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When falling back to an allocation from the HW header cache, check if
the skb is eligible for using memory reserves.
This only makes a difference if the cache is empty and needs to be
refilled.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use dev_alloc_page() for backing the RX buffers with pages. This way we
pick up __GFP_MEMALLOC.
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement helpers for PCS accessed via the MII bus using 802.3 clause
45 cycles for 10GBASE-R. Only link up/down is supported, 10G full
duplex is assumed.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement helpers for PCS accessed via the MII bus using 802.3 clause
22 cycles, conforming to 802.3 clause 37 and Cisco SGMII specifications
for the advertisement word.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add APIs for modifying a MDIO device register, similar to the existing
phy_modify() group of functions, but at mdiobus level instead.  Adapt
__phy_modify_changed() to use the new mdiobus level helper.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid using BUG_ON() in the mdiobus accessors, prefering instead to use
WARN_ON_ONCE() and returning an error.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds the support for Enterprise MAC IP version which is very similar to
XGMAC. It's so similar that we just need to check the device id and add
new speeds definitions and some minor callbacks.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add XLGMII support for stmmac including the list of speeds and defines
for them.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add XLGMII support for XPCS. This does not include Autoneg feature.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add decoding for a new firmware error code.
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we don't recognize the transceiver type, set the xcvr type
and data length such that ethtool can at least print the first
256 bytes and the reader can figure out why the transceiver
is not recognized.

While we're here, we can update the phy_id type values to use
the enum values in sfp.h.

Fixes: 4d03e00a ("ionic: Add initial ethtool support")
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the adminq's napi struct when tearing down
the adminq.

Fixes: 1d062b7b ("ionic: Add basic adminq support")
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't bother de-initing RSS if it wasn't selected.

Fixes: aa319881 ("ionic: Add RSS support")
Signed-off-by: NShannon Nelson <snelson@pensando.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>