The SRR0 and SRR1 registers contain cached values of the PC and MSR
respectively. They get written to by the hypervisor when an interrupt
occurs or directly by the kernel. They are also used to tell the rfi(d)
instruction where to jump to.

Because it only gets touched on defined events that, it's very simple to
share with the guest. Hypervisor and guest both have full r/w access.

This patch converts all users of the current field to the shared page.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The DAR register contains the address a data page fault occured at. This
register behaves pretty much like a simple data storage register that gets
written to on data faults. There is no hypervisor interaction required on
read or write.

This patch converts all users of the current field to the shared page.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The DSISR register contains information about a data page fault. It is fully
read/write from inside the guest context and we don't need to worry about
interacting based on writes of this register.

This patch converts all users of the current field to the shared page.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

One of the most obvious registers to share with the guest directly is the
MSR. The MSR contains the "interrupts enabled" flag which the guest has to
toggle in critical sections.

So in order to bring the overhead of interrupt en- and disabling down, let's
put msr into the shared page. Keep in mind that even though you can fully read
its contents, writing to it doesn't always update all state. There are a few
safe fields that don't require hypervisor interaction. See the documentation
for a list of MSR bits that are safe to be set from inside the guest.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

For transparent variable sharing between the hypervisor and guest, I introduce
a shared page. This shared page will contain all the registers the guest can
read and write safely without exiting guest context.

This patch only implements the stubs required for the basic structure of the
shared page. The actual register moving follows.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

If a nop instruction is encountered, we jump directly to the done label.
This skip updating rip. Break from the switch case instead
Signed-off-by: NMohammed Gamal <m.gamal005@gmail.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Since modrm operand can be either register or memory, decoding it into
a 'struct operand', which can represent both, is simpler.
Signed-off-by: NAvi Kivity <avi@redhat.com>

Instead of using modrm_ea, which will soon be gone.
Signed-off-by: NAvi Kivity <avi@redhat.com>

The NoAccess flag will prevent memory from being accessed.
Signed-off-by: NAvi Kivity <avi@redhat.com>

Use for INVLPG, which accesses the tlb, not memory.
Signed-off-by: NAvi Kivity <avi@redhat.com>

This is an ordinary modrm source or destination; use the standard structure
representing it.
Signed-off-by: NAvi Kivity <avi@redhat.com>

This is an ordinary modrm source or destination; use the standard structure
representing it.
Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

The operands for these instructions are 32 bits or 64 bits, depending on
long mode, and ignoring REX prefixes, or the operand size prefix.
Signed-off-by: NAvi Kivity <avi@redhat.com>

(x && (x & y)) == (x & y)
Signed-off-by: NAvi Kivity <avi@redhat.com>

Unused (and has never been).
Signed-off-by: NAvi Kivity <avi@redhat.com>

The code is repeated three times, put it into fetch_register_operand()
Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Use X8() to avoid repetition.
Signed-off-by: NAvi Kivity <avi@redhat.com>

Currently we use a void pointer for memory addresses.  That's wrong since
these are guest virtual addresses which are not directly dereferencable by
the host.

Use the correct type, unsigned long.
Signed-off-by: NAvi Kivity <avi@redhat.com>

Let it compute modrm_seg instead, and have the caller apply it.
Signed-off-by: NAvi Kivity <avi@redhat.com>

This patch lets a nested vmrun fail if the L1 hypervisor
left the asid zero. This fixes the asid_zero unit test.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This patch lets the nested vmrun fail if the L1 hypervisor
has not intercepted vmrun. This fixes the "vmrun intercept
check" unit test.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Mark page dirty only when this page is really written, it's more exacter,
and also can fix dirty page marking in speculation path
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Introduce spte_has_volatile_bits() function to judge whether spte
bits will miss, it's more readable and can help us to cleanup code
later
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

It's a small cleanup that using using kvm_set_pfn_accessed() instead
of mark_page_accessed()
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Do not recheck io permission on every iteration.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

LMSW is documented not to be able to clear cr0.pe; make it so.
Signed-off-by: NAvi Kivity <avi@redhat.com>

No need to update vcpu state since instruction is in the middle of the
emulation.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Needed for repeating instructions with execution functions.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

So they can reference execution functions.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

No code changes.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Instead of looking up the opcode twice (once for decode flags, once for
the big execution switch) look up both flags and function in the decode tables.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

It doesn't ever change, so we don't need to pass it around everywhere.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Now that the group index no longer exists, the space is free.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>