Add explanatory comment to avoid confusion when a pointer is set
to the second word of an array instead of the customary cast of a
pointer to the beginning of the array.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The igb online link test was always reporting pass because instead of
checking for if_running it was checking for netif_carrier_ok.

This change corrects the test so that it is run if the interface is running
instead of checking for netif carrier ok.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check the value of max_vfs at the time of assignment of vfs_allocated_count.

The previous check in igb_probe_vfs was too late as by that time the rx/tx
rings were initialized with the wrong offset.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 82576 expects the second rx queue in any pool to receive L2 switch
loop back packets sent from the second tx queue in another pool.  The
82576 VF driver does not enable the second rx queue so if the PF driver
sends packets destined to a VF from its second tx queue then the VF
driver will never see them.  In SR-IOV mode limit the number of tx queues
used by the PF driver to one. This patch fixes a bug reported in which
the PF cannot communciate with the VF and should be considered for 2.6.34
stable.

CC: stable@kernel.org
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

82580 NICs can have up to 4 functions. This fixes phy accesses
to use the correct locks for functions 2 and 3.
Signed-off-by: NNicholas Nunley <nicholasx.d.nunley@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the CONFIG_MCORE2 check from around NET_IP_ALIGN.  It is
based on a suggestion from Andi Kleen.  The assumption is that there are
not any x86 cores where unaligned access is really slow, and this change
would allow for a performance improvement to still exist on configurations
that are not necessarily optimized for Core 2.

Cc: Andi Kleen <ak@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add error checking to DMA descriptor rings initialization code.
Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

be2net driver is currently not showing correct phy details in certain cases.
This patch fixes it.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since ehea_get_stats calls ehea_h_query_ehea_port, which
can sleep, we can also sleep when allocating a page in
this function. This fixes some memory allocation failure
warnings seen under low memory conditions.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/wireless/libertas/host.h

x86 architectures can handle unaligned accesses in hardware, and it has
been shown that unaligned DMA accesses can be expensive on Nehalem
architectures.  As such we should overwrite NET_IP_ALIGN to resolve
this issue.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for 1G SFP+ PHY's to 82599.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow ethtool to query the number of RX rings, the fields used in RX
flow hashing and the hash indirection table.

Allow ethtool to update the RX flow hash indirection table.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many NICs use an indirection table to map an RX flow hash value to one
of an arbitrary number of queues (not necessarily a power of 2).  It
can be useful to remove some queues from this indirection table so
that they are only used for flows that are specifically filtered
there.  It may also be useful to weight the mapping to account for
user processes with the same CPU-affinity as the RX interrupts.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only some netdev feature flags correspond directly to ethtool feature
flags.  ethtool_op_get_flags() does the right thing.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NBhavesh Davda <bhavesh@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The documented error code for attempts to set unsupported flags (or
to clear flags that cannot be disabled) is EINVAL, not EOPNOTSUPP.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ethtool_op_set_flags() does not check for unsupported flags, and has
no way of doing so.  This means it is not suitable for use as a
default implementation of ethtool_ops::set_flags.

Add a 'supported' parameter specifying the flags that the driver and
hardware support, validate the requested flags against this, and
change all current callers to pass this parameter.

Change some other trivial implementations of ethtool_ops::set_flags to
call ethtool_op_set_flags().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Reviewed-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use correct shift factor for extracting the SGE DMA Ingress Padding
Boundary.  Was accidentally using the register field's shift which was
close enough (4 instead of the propper value of 5) that it actually
sort of worked for various packet sizes ...
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove obsolete comment about the lack of a TX Timer Callback -- which
we now _do_ have ...
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add fast path for in-order fragments

As the fragments are sent in order in most of OSes, such as Windows, Darwin and
FreeBSD, it is likely the new fragments are at the end of the inet_frag_queue.
In the fast path, we check if the skb at the end of the inet_frag_queue is the
prev we expect.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
----
 include/net/inet_frag.h |    1 +
 net/ipv4/ip_fragment.c  |   12 ++++++++++++
 net/ipv6/reassembly.c   |   11 +++++++++++
 3 files changed, 24 insertions(+)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

/proc/net/snmp and /proc/net/netstat expose SNMP counters.

Width of these counters is either 32 or 64 bits, depending on the size
of "unsigned long" in kernel.

This means user program parsing these files must already be prepared to
deal with 64bit values, regardless of user program being 32 or 64 bit.

This patch introduces 64bit snmp values for IPSTAT mib, where some
counters can wrap pretty fast if they are 32bit wide.

# netstat -s|egrep "InOctets|OutOctets"
    InOctets: 244068329096
    OutOctets: 244069348848
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ibm p7 architecure seems to reorder memory accesses more
aggressively than previous ppc64 architectures. This requires memory
barriers to ensure that rx/tx doorbells are pressed only after
memory to be DMAed is written.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original code is off by one because we should start counting at
zero.  So the size of the resource is end - start + 1.  I switched it to
use resource_size() to do the calculation.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

act_nat: use stack variable

structure tc_nat isn't too big for stack, so we can put it in stack.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
----
 net/sched/act_nat.c |   31 ++++++++++---------------------
 1 file changed, 10 insertions(+), 21 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

act_mirred: combine duplicate code

tcf_bstats is updated in any way, so we can do it earlier to reduce the size of
the code.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca>
----
 net/sched/act_mirred.c |    6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'Shoul' must be 'should'.
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow selection of minstrel_ht as default rate control algorithm. At
the moment minstrel_ht can only be requested by the driver code but
not selected as default in make menuconfig. Fix this by using
minstrel_ht when minstrel was selected as default and minstrel_ht
is available.

This change won't affect legacy devices as minstrel_ht falls back to
minstrel in that case.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When issuing a reset, the TSF value is lost in the hardware because of
the 913x specific cold reset. As with some AR9280 cards, the TSF needs
to be preserved in software here.

Additionally, there's an issue that frequently prevents a successful
TSF write directly after the chip reset. In this case, repeating the
TSF write after the initval-writes usually works.

This patch detects failed TSF writes and recovers from them, taking
into account the delay caused by the initval writes.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Reported-by: NBjörn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CC [M]  drivers/net/wireless/rt2x00/rt2800lib.o
drivers/net/wireless/rt2x00/rt2800lib.c: In function 'rt2800_ampdu_action':
drivers/net/wireless/rt2x00/rt2800lib.c:2821: warning: unused variable 'rt2x00dev'
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Latest rt2870 legacy driver also sets BBP_CSR_CFG_BBP_RW_MODE to 1
when reading or writing the EEPROM. This means we can make the
BBP reading and writing completely equal on all platforms.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Legacy driver indicates that BBP1_TX_ANTENNA must be set
to 0 for TXPATH values of 1 and 3. So the previous statement
that nothing should be done for TXPATH = 3, is false.

Furthermore, remove the false BBP3_RX_ANTENNA initialization
when TXPATH is 1 for PCI and SOC devices. This field will always
be overridden in the next switch statement, making this initialization
bogus. History of this line indicates it was there from the beginning,
and was once caught as typo. Instead of replacing the line with the
correct line, the correct line was added...
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IEEE80211_HT_CAP_RX_STBC is a 2 bit flag, and should thus
never be set as normal flag. Instead we must read the number
of RX paths from the EEPROM and set the IEEE80211_HT_CAP_RX_STBC
with the correct value (using the same logic as the number of TX
streams).
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When an interface is removed the according beacon entry should be reset.
The current approach to only clear the first word is not enough to stop
the device from sending out the beacon, hence resulting in beacons being
sent out for already removed interfaces.

Fix this by invalidating the entire TXWI in front of the beacon instead
of only the first word.

Also clear all beacons during startup in the same way.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since the link tuning is based on average RSSI values taken from all received
frames it doesn't make sense to enable it in AP mode where every associated
station provides independent RSSI values. Furthermore the legacy drivers
don't enable link tuning in AP mode as well.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix rt61pci beacon updates in the same way as rt2800pci. rt61pci didn't
update the beacon template after each beacon interval, resulting in the
DTIM count being incorrect (if DTIM period > 1). Fix this by calling
rt2x00lib_beacondone after the current beacon was sent out.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2800pci didn't update the beacon template after each beacon interval,
resulting in the DTIM count being incorrect (if DTIM period > 1). Fix this
by calling rt2x00lib_beacondone after the current beacon was sent out.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

MAC_BSSID_DW1_BSS_ID_MASK must be set to the mask 3, to
enable 8 BSSID's. The MAC_BSSID_DW1_BSS_BCN_NUM is initialized
to 7 to enable the 8 beacons.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Tested-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Align with the latest versions of the Ralink legacy driver(s).
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>