No functional change. But let's get first i915 pointer
directly from intel_dp so we can clean up a lot of code
later.
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180827223021.7145-1-rodrigo.vivi@intel.com

gen8_de_irq_postinstall() wasn't masking the IRQ bit before passing the
debug flag to psr_irq_control(). This check was missed when new debug bits
were defined in  'commit c44301fc ("drm/i915: Allow control of PSR at
runtime through debugfs, v6")'. Instead of ANDing the irq bit in all the
callers, move it to the callee.

v2: Rebased.

Fixes: c44301fc ("drm/i915: Allow control of PSR at runtime through
debugfs, v6")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180821221156.2442-3-dhinakaran.pandiyan@intel.com

Knowing the status of the PSR HW state machine is useful for debug,
especially since we are seeing errors with PSR2 in CI.

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180821221156.2442-1-dhinakaran.pandiyan@intel.com

After
commit 2cd9a689 ("drm/i915: Refactor intel_display_set_init_power() logic")
it makes more sense to check the power domain/well refcounts after
enabling the power domains functionality. Before that it's guaranteed
that most power wells (in the INIT domain) will have a reference held,
so not an interesting state.

While at it also add the check after the init_hw/fini_hw, disable and
suspend/resume steps. Make the test optional on a Kconfig option since
it may add substantial overhead: on VLV/CHV the corresponding PUNIT reg
access for each power well may take up to 20ms.

v2:
- Add the state check to more spots. (Chris)

v3:
- During suspend check the state before deiniting display core.
  Afterwards DC states are disabled (and so the dc_off power well is
  enabled) even though we don't hold a reference on it.
- Do the test conditionally based on a new Kconfig option. (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
[Add DRM_I915_DEBUG_RUNTIME_PM to welcome messages]
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817145837.26592-1-imre.deak@intel.com

The device global init_power_on flag is somewhat arbitrary and makes
debugging power refcounting problems difficult. Instead arrange things
so that all display power domain get has a corresponding put call. After
this change we have the following sequences:

driver loading:
intel_power_domains_init_hw();
<other init steps>
intel_power_domains_enable();

driver unloading:
intel_power_domains_disable();
<other uninit steps>
intel_power_domains_fini_hw();

system suspend:
intel_power_domains_disable();
<other suspend steps>
intel_power_domains_suspend();

system resume:
intel_power_domains_resume();
<other resume steps>
intel_power_domains_enable();

at other times while the driver is loaded:
intel_display_power_get();
...
intel_display_power_put();
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180816123757.3286-2-imre.deak@intel.com

Currently, we cancel the extra wakeref we have for !runtime-pm devices
inside power_wells_fini_hw. However, this is not strictly paired with
the acquisition of that wakeref in runtime_pm_enable (as the fini_hw may
be called on errors paths before we even call runtime_pm_enable). Make
the symmetry more explicit and include a check that we do release all of
our rpm wakerefs.

v2: Fixup transfer of ownership back to core whilst keeping our wakeref
count balanced.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180816123757.3286-1-imre.deak@intel.com

Currently tests modify i915.enable_psr and then do a modeset cycle
to change PSR. We can write a value to i915_edp_psr_debug to force
a certain PSR mode without a modeset.

To retain compatibility with older userspace, we also still allow
the override through the module parameter, and add some tracking
to check whether a debugfs mode is specified.

Changes since v1:
- Rename dev_priv->psr.enabled to .dp, and .hw_configured to .enabled.
- Fix i915_psr_debugfs_mode to match the writes to debugfs.
- Rename __i915_edp_psr_write to intel_psr_set_debugfs_mode, simplify
  it and move it to intel_psr.c. This keeps all internals in intel_psr.c
- Perform an interruptible wait for hw completion outside of the psr
  lock, instead of being forced to trywait and return -EBUSY.
Changes since v2:
- Rebase on top of intel_psr changes.
Changes since v3:
- Assign psr.dp during init. (dhnkrn)
- Add prepared bool, which should be used instead of relying on psr.dp. (dhnkrn)
- Fix -EDEADLK handling in debugfs. (dhnkrn)
- Clean up waiting for idle in intel_psr_set_debugfs_mode.
- Print PSR mode when trying to enable PSR. (dhnkrn)
- Move changing psr debug setting to i915_edp_psr_debug_set. (dhnkrn)
Changes since v4:
- Return error in _set() function.
- Change flag values to make them easier to remember. (dhnkrn)
- Only assign psr.dp once. (dhnkrn)
- Only set crtc_state->has_psr on the crtc with psr.dp.
- Fix typo. (dhnkrn)
Changes since v5:
- Only wait for PSR idle on the PSR connector correctly. (dhnkrn)
- Reinstate WARN_ON(drrs.dp) in intel_psr_enable. (dhnkrn)
- Remove stray comment. (dhnkrn)
- Be silent in intel_psr_compute_config on wrong connector. (dhnkrn)
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180809142101.26155-1-maarten.lankhorst@linux.intel.comReviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>

It makes sense to keep unchanging data const. Extract such fields from
the i915_power_well struct into a new i915_power_well_desc struct that
we initialize during compile time. For the rest of the dynamic
fields allocate an array of i915_power_well objects in i915 dev_priv,
and link to each of these objects their corresponding
i915_power_well_desc object.

v2:
- Fix checkpatch warnings about missing param name in fn declaration and
  lines over 80 chars. (Paulo)
- Move check for unique IDs to __set_power_wells().

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
[Fixed checkpatch warn in __set_power_wells()]
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-5-imre.deak@intel.com

intel_power_domains_fini() rolls back what was done in
intel_power_domains_init_hw(), so rename and move it accordingly. This
allows us adding a cleanup function later for intel_power_domains_init()
in a cleaner way.

No functional change.

v2:
- Fix checkpatch error adding missing param name to function
  declaration. (Paulo)

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-3-imre.deak@intel.com

RPS provides a feedback loop where we use the load during the previous
evaluation interval to decide whether to up or down clock the GPU
frequency. Our responsiveness is split into 3 regimes, a high and low
plateau with the intent to keep the gpu clocked high to cover occasional
stalls under high load, and low despite occasional glitches under steady
low load, and inbetween. However, we run into situations like kodi where
we want to stay at low power (video decoding is done efficiently
inside the fixed function HW and doesn't need high clocks even for high
bitrate streams), but just occasionally the pipeline is more complex
than a video decode and we need a smidgen of extra GPU power to present
on time. In the high power regime, we sample at sub frame intervals with
a bias to upclocking, and conversely at low power we sample over a few
frames worth to provide what we consider to be the right levels of
responsiveness respectively. At low power, we more or less expect to be
kicked out to high power at the start of a busy sequence by waitboosting.

Prior to commit e9af4ea2 ("drm/i915: Avoid waitboosting on the active
request") whenever we missed the frame or stalled, we would immediate go
full throttle and upclock the GPU to max. But in commit e9af4ea2, we
relaxed the waitboosting to only apply if the pipeline was deep to avoid
over-committing resources for a near miss. Sadly though, a near miss is
still a miss, and perceptible as jitter in the frame delivery.

To try and prevent the near miss before having to resort to boosting
after the fact, we use the pageflip queue as an indication that we are
in an "interactive" regime and so should sample the load more frequently
to provide power before the frame misses it vblank. This will make us
more favorable to providing a small power increase (one or two bins) as
required rather than going all the way to maximum and then having to
work back down again. (We still keep the waitboosting mechanism around
just in case a dramatic change in system load requires urgent uplocking,
faster than we can provide in a few evaluation intervals.)

v2: Reduce rps_set_interactive to a boolean parameter to avoid the
confusion of what if they wanted a new power mode after pinning to a
different mode (which to choose?)
v3: Only reprogram RPS while the GT is awake, it will be set when we
wake the GT, and while off warns about being used outside of rpm.
v4: Fix deferred application of interactive mode
v5: s/state/interactive/
v6: Group the mutex with its principle in a substruct

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107111
Fixes: e9af4ea2 ("drm/i915: Avoid waitboosting on the active request")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180731132629.3381-1-chris@chris-wilson.co.uk

The Gen11 TypeC PHY DDI Buffer chapter, PHY Clock Gating Programming
section says that PHY clock gating should be disabled before starting
voltage swing programming, then enabled after any link training is
complete.

v2: Simple rebase.

Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v1)
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-6-paulo.r.zanoni@intel.com

Programming this register is part of the Enable Sequence for
DisplayPort on ICL. Do as the spec says.

v2: Simple rebase.

Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v1)
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-5-paulo.r.zanoni@intel.com

The type is detected based on the live status bits. Once detected,
it's not supposed to be changed, so we have some sanity checks for
that.

v2: Rebase.

Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-3-paulo.r.zanoni@intel.com

With neither LVDS or eDP no longer using intel_panel_detect() we can
kill it, and the accompanying modparam.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180717174216.22252-3-ville.syrjala@linux.intel.comReviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

It was originally introduced following the VESA spec in order to validate PSR.

However we found so many issues around sink_crc that instead of helping PSR
development it only brought another layer of trouble to the table.

So, sink_crc has been a black whole for us in question of time, effort and hope.

First of the problems is that HW statement is clear: "Do not attempt to use
aux communication with PSR enabled". So the main reason behind sink_crc is
already compromised.

For a while we had hope on the aux-mutex could workaround this problem on SKL+
platforms, but that mutex was not reliable, not tested,
and we shouldn't use according to HW engineers.

Also, nor source, nor sink designed and implemented the sink_crc to be used like
we are trying to use here.

Well, the sink side of things is also apparently not prepared for this
case. Each panel that we tried seemed to have a different behavior with same
code and same source.

So, for all the time we lost on trying to ducktape all these different issues
I believe it is now time to move PSR to a more reliable validation.
Maybe not a perfect one as we dreamed for this sink_crc, but at least more
reliable.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705192528.30515-1-rodrigo.vivi@intel.com

drm_format_info table has a field 'is_yuv' to denote if the format
is yuv or not. The driver is expected to use this instead of
having a function for the same purpose.
Signed-off-by: NAyan Kumar halder <ayan.halder@arm.com>
Reviewed-by: NVille Syrjala <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1531847626-22248-2-git-send-email-ayan.halder@arm.com

With the new CSB processing code, we are not vulnerable to delayed
delivery of a pre-reset interrupt as we use the CSB status pointers in
the HWSP to decide if we need to parse any CSB events and no longer need
to wait for the first post-reset interrupt to be assured that the CSB
mmio registers are valid.

The new icl code to clear registers has a nasty lock inversion:
[   57.409776] ======================================================
[   57.409779] WARNING: possible circular locking dependency detected
[   57.409783] 4.18.0-rc4-CI-CI_DII_1137+ #1 Tainted: G     U  W
[   57.409785] ------------------------------------------------------
[   57.409788] swapper/6/0 is trying to acquire lock:
[   57.409790] 000000004f304ee5 (&engine->timeline.lock/1){-.-.}, at: execlists_submit_request+0x2b/0x1a0 [i915]
[   57.409841]
               but task is already holding lock:
[   57.409844] 00000000aad89594 (&(&rq->lock)->rlock#2){-.-.}, at: notify_ring+0x2b2/0x480 [i915]
[   57.409869]
               which lock already depends on the new lock.

[   57.409872]
               the existing dependency chain (in reverse order) is:
[   57.409876]
               -> #2 (&(&rq->lock)->rlock#2){-.-.}:
[   57.409900]        notify_ring+0x2b2/0x480 [i915]
[   57.409922]        gen8_cs_irq_handler+0x39/0xa0 [i915]
[   57.409943]        gen11_irq_handler+0x2f0/0x420 [i915]
[   57.409949]        __handle_irq_event_percpu+0x42/0x370
[   57.409952]        handle_irq_event_percpu+0x2b/0x70
[   57.409956]        handle_irq_event+0x2f/0x50
[   57.409959]        handle_edge_irq+0xe7/0x190
[   57.409964]        handle_irq+0x67/0x160
[   57.409967]        do_IRQ+0x5e/0x120
[   57.409971]        ret_from_intr+0x0/0x1d
[   57.409974]        _raw_spin_unlock_irqrestore+0x4e/0x60
[   57.409979]        tasklet_action_common.isra.5+0x47/0xb0
[   57.409982]        __do_softirq+0xd9/0x505
[   57.409985]        irq_exit+0xa9/0xc0
[   57.409988]        do_IRQ+0x9a/0x120
[   57.409991]        ret_from_intr+0x0/0x1d
[   57.409995]        cpuidle_enter_state+0xac/0x360
[   57.409999]        do_idle+0x1f3/0x250
[   57.410004]        cpu_startup_entry+0x6a/0x70
[   57.410010]        start_secondary+0x19d/0x1f0
[   57.410015]        secondary_startup_64+0xa5/0xb0
[   57.410018]
               -> #1 (&(&dev_priv->irq_lock)->rlock){-.-.}:
[   57.410081]        clear_gtiir+0x30/0x200 [i915]
[   57.410116]        execlists_reset+0x6e/0x2b0 [i915]
[   57.410140]        i915_reset_engine+0x111/0x190 [i915]
[   57.410165]        i915_handle_error+0x11a/0x4a0 [i915]
[   57.410198]        i915_hangcheck_elapsed+0x378/0x530 [i915]
[   57.410204]        process_one_work+0x248/0x6c0
[   57.410207]        worker_thread+0x37/0x380
[   57.410211]        kthread+0x119/0x130
[   57.410215]        ret_from_fork+0x3a/0x50
[   57.410217]
               -> #0 (&engine->timeline.lock/1){-.-.}:
[   57.410224]        _raw_spin_lock_irqsave+0x33/0x50
[   57.410256]        execlists_submit_request+0x2b/0x1a0 [i915]
[   57.410289]        submit_notify+0x8d/0x124 [i915]
[   57.410314]        __i915_sw_fence_complete+0x81/0x250 [i915]
[   57.410339]        dma_i915_sw_fence_wake+0xd/0x20 [i915]
[   57.410344]        dma_fence_signal_locked+0x79/0x200
[   57.410368]        notify_ring+0x2ba/0x480 [i915]
[   57.410392]        gen8_cs_irq_handler+0x39/0xa0 [i915]
[   57.410416]        gen11_irq_handler+0x2f0/0x420 [i915]
[   57.410421]        __handle_irq_event_percpu+0x42/0x370
[   57.410425]        handle_irq_event_percpu+0x2b/0x70
[   57.410428]        handle_irq_event+0x2f/0x50
[   57.410432]        handle_edge_irq+0xe7/0x190
[   57.410436]        handle_irq+0x67/0x160
[   57.410439]        do_IRQ+0x5e/0x120
[   57.410445]        ret_from_intr+0x0/0x1d
[   57.410449]        cpuidle_enter_state+0xac/0x360
[   57.410453]        do_idle+0x1f3/0x250
[   57.410456]        cpu_startup_entry+0x6a/0x70
[   57.410460]        start_secondary+0x19d/0x1f0
[   57.410464]        secondary_startup_64+0xa5/0xb0
[   57.410466]
               other info that might help us debug this:

[   57.410471] Chain exists of:
                 &engine->timeline.lock/1 --> &(&dev_priv->irq_lock)->rlock --> &(&rq->lock)->rlock#2

[   57.410481]  Possible unsafe locking scenario:

[   57.410485]        CPU0                    CPU1
[   57.410487]        ----                    ----
[   57.410490]   lock(&(&rq->lock)->rlock#2);
[   57.410494]                                lock(&(&dev_priv->irq_lock)->rlock);
[   57.410498]                                lock(&(&rq->lock)->rlock#2);
[   57.410503]   lock(&engine->timeline.lock/1);
[   57.410506]
                *** DEADLOCK ***

[   57.410511] 4 locks held by swapper/6/0:
[   57.410514]  #0: 0000000074575789 (&(&dev_priv->irq_lock)->rlock){-.-.}, at: gen11_irq_handler+0x8a/0x420 [i915]
[   57.410542]  #1: 000000009b29b30e (rcu_read_lock){....}, at: notify_ring+0x1a/0x480 [i915]
[   57.410573]  #2: 00000000aad89594 (&(&rq->lock)->rlock#2){-.-.}, at: notify_ring+0x2b2/0x480 [i915]
[   57.410601]  #3: 000000009b29b30e (rcu_read_lock){....}, at: submit_notify+0x35/0x124 [i915]
[   57.410635]
               stack backtrace:
[   57.410640] CPU: 6 PID: 0 Comm: swapper/6 Tainted: G     U  W         4.18.0-rc4-CI-CI_DII_1137+ #1
[   57.410644] Hardware name: Intel Corporation Ice Lake Client Platform/IceLake U DDR4 SODIMM PD RVP, BIOS ICLSFWR1.R00.2222.A01.1805300339 05/30/2018
[   57.410650] Call Trace:
[   57.410652]  <IRQ>
[   57.410657]  dump_stack+0x67/0x9b
[   57.410662]  print_circular_bug.isra.16+0x1c8/0x2b0
[   57.410666]  __lock_acquire+0x1897/0x1b50
[   57.410671]  ? lock_acquire+0xa6/0x210
[   57.410674]  lock_acquire+0xa6/0x210
[   57.410706]  ? execlists_submit_request+0x2b/0x1a0 [i915]
[   57.410711]  _raw_spin_lock_irqsave+0x33/0x50
[   57.410741]  ? execlists_submit_request+0x2b/0x1a0 [i915]
[   57.410769]  execlists_submit_request+0x2b/0x1a0 [i915]
[   57.410774]  ? _raw_spin_unlock_irqrestore+0x39/0x60
[   57.410804]  submit_notify+0x8d/0x124 [i915]
[   57.410828]  __i915_sw_fence_complete+0x81/0x250 [i915]
[   57.410854]  dma_i915_sw_fence_wake+0xd/0x20 [i915]
[   57.410858]  dma_fence_signal_locked+0x79/0x200
[   57.410882]  notify_ring+0x2ba/0x480 [i915]
[   57.410907]  gen8_cs_irq_handler+0x39/0xa0 [i915]
[   57.410933]  gen11_irq_handler+0x2f0/0x420 [i915]
[   57.410938]  __handle_irq_event_percpu+0x42/0x370
[   57.410943]  handle_irq_event_percpu+0x2b/0x70
[   57.410947]  handle_irq_event+0x2f/0x50
[   57.410951]  handle_edge_irq+0xe7/0x190
[   57.410955]  handle_irq+0x67/0x160
[   57.410958]  do_IRQ+0x5e/0x120
[   57.410962]  common_interrupt+0xf/0xf
[   57.410965]  </IRQ>
[   57.410969] RIP: 0010:cpuidle_enter_state+0xac/0x360
[   57.410972] Code: 44 00 00 31 ff e8 84 93 91 ff 45 84 f6 74 12 9c 58 f6 c4 02 0f 85 31 02 00 00 31 ff e8 7d 30 98 ff e8 e8 0e 94 ff fb 4c 29 fb <48> ba cf f7 53 e3 a5 9b c4 20 48 89 d8 48 c1 fb 3f 48 f7 ea b8 ff
[   57.411015] RSP: 0018:ffffc90000133e90 EFLAGS: 00000216 ORIG_RAX: ffffffffffffffdd
[   57.411023] RAX: ffff8804ae748040 RBX: 000000000002a97d RCX: 0000000000000000
[   57.411029] RDX: 0000000000000046 RSI: ffffffff82141263 RDI: ffffffff820f05a7
[   57.411035] RBP: 0000000000000001 R08: 0000000000000001 R09: 0000000000000000
[   57.411041] R10: 0000000000000000 R11: 0000000000000000 R12: ffffffff8229f078
[   57.411045] R13: ffff8804ab2adfa8 R14: 0000000000000000 R15: 0000000d5de092e3
[   57.411052]  do_idle+0x1f3/0x250
[   57.411055]  cpu_startup_entry+0x6a/0x70
[   57.411059]  start_secondary+0x19d/0x1f0
[   57.411064]  secondary_startup_64+0xa5/0xb0

The easiest remedy is to remove the defunct code.

Fixes: ff047a87 ("drm/i915/icl: Correctly clear lost ctx-switch interrupts across reset for Gen11")
References: fd8526e5 ("drm/i915/execlists: Trust the CSB")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180713203529.1973-3-chris@chris-wilson.co.uk

Instead of looping over ports and hpd_pins, let's loop over
the encoders when doing hotplug processing. And instead of
depending on dev_priv->irq_port[] to tell us whether the
encoder has the ->hpd_pulse() hook or not, we can just
check for that directly. So we can just nuke irq_port[] entirely.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705164357.28512-5-ville.syrjala@linux.intel.comReviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Rather than looping over all the ports and picking the encoder based on
the port, let's just loop over all the encoders instead. Gets rid of
some irq_port[] usage, which is a bit of an eye sore.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705164357.28512-4-ville.syrjala@linux.intel.comReviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Add intel_encoder_is_dig_port() to match intel_encoder_is_dp().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705164357.28512-3-ville.syrjala@linux.intel.comReviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Add a convenience macro for iterating DP encoders.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705164357.28512-2-ville.syrjala@linux.intel.comReviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

On GLK NUC platforms the HDMI retiming buffer needs additional disabled
time to correctly sync to a faster incoming signal.

When measured on a scope the highspeed lines of the HDMI clock turn off
 for ~400uS during a normal resolution change. The HDMI retimer on the
 GLK NUC appears to require at least a full frame of quiet time before a
new faster clock can be correctly sync'd. Wait 100ms due to msleep
inaccuracies while waiting for a completed frame. Add a quirk to the
driver for GLK boards that use ITE66317 HDMI retimers.

V2: Add more devices to the quirk list
V3: Delay increased to 100ms, check to confirm crtc type is HDMI.
V4: crtc type check extended to include _DDI and whitespace fixes
v5: Fix white spaces, remove the macro for delay. Revert the crtc type
    check introduced in v4.

Cc: Imre Deak <imre.deak@intel.com>
Cc: <stable@vger.kernel.org> # v4.14+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105887Signed-off-by: NClint Taylor <clinton.a.taylor@intel.com>
Tested-by: NDaniel Scheller <d.scheller.oss@gmail.com>
Signed-off-by: NRadhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710200205.1478-1-radhakrishna.sripada@intel.com

In commit "drm/i915: Wait for PSR exit before checking for vblank
evasion", the idea was to limit the PSR IDLE checks when PSR is
actually supported. While CAN_PSR does do that check, it doesn't
applies on a per-crtc basis. crtc_state->has_psr is a more granular
check that only applies to pipe(s) that have PSR enabled.

Without the has_psr check, we end up waiting on the eDP transcoder's
PSR_STATUS register irrespective of whether the pipe being updated is
driving it or not.

v2: Remove unnecessary parantheses, make checkpatch happy.

v3: Move the has_psr check to intel_psr_wait_for_idle and commit
    message changes (DK).

v4: Derive dev_priv from intel_crtc_state (DK)

v5: Commit message changes to reflect the HW behavior (DK)

Fixes: a6089879 ("drm/i915: Wait for PSR exit before checking for vblank evasion")
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NTarun Vyas <tarun.vyas@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712053323.26266-1-tarun.vyas@intel.com

This interface is deprecated, and has been replaced by the upstream
drm crc interface.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Cc: Petri Latvala <petri.latvala@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628072303.14175-1-maarten.lankhorst@linux.intel.com

Avoid confusion with the functions to be added for the new ICL or gen 11
DSI implementation by renaming the current DSI functions. While at it,
permutate the words in the function names to make them all start with
"vlv_dsi" or "vlv_dsi_pll" etc.

Reduce the platform abstractions in the PLL file while at it, moving the
checks to vlv_dsi.c instead, where we typically already have the
necessary if ladders.

Leave the static functions as-is for now; they could be renamed later if
needed.

No functional changes.

v2: use "gen7" prefix.

v3: use "vlv" and "bxt" prefixes, reduce the abstractions.

References: https://patchwork.freedesktop.org/series/44823/
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMadhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705132509.12881-2-jani.nikula@intel.com

Starting from ICL or gen 11 we have a new DSI block which requires
completely different programming from the current implementation. Having
them in the same file would be confusing. Rename the current DSI and DSI
PLL implementation files as vlv_dsi.c and vlv_dsi_pll.c.

No functional changes.

v2: use "gen7" prefix.

v3: use "vlv" prefix.

References: https://patchwork.freedesktop.org/series/44823/
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMadhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705132509.12881-1-jani.nikula@intel.com

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 141432
Addresses-Coverity-ID: 141433
Addresses-Coverity-ID: 141434
Addresses-Coverity-ID: 141435
Addresses-Coverity-ID: 141436
Addresses-Coverity-ID: 1357360
Addresses-Coverity-ID: 1357403
Addresses-Coverity-ID: 1357433
Addresses-Coverity-ID: 1392622
Addresses-Coverity-ID: 1415273
Addresses-Coverity-ID: 1435752
Addresses-Coverity-ID: 1441500
Addresses-Coverity-ID: 1454596
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628223541.GA17665@embeddedor.com

This is a lockless version of the exisiting psr_wait_for_idle().
We want to wait for PSR to idle out inside intel_pipe_update_start.
At the time of a pipe update, we should never race with any psr
enable or disable code, which is a part of crtc enable/disable.
The follow up patch will use this lockless wait inside pipe_update_
start to wait for PSR to idle out before checking for vblank evasion.
We need to keep the wait in pipe_update_start to as less as it can be.
So,we can live and flourish w/o taking any psr locks at all.

Even if psr is never enabled, psr2_enabled will be false and this
function will wait for PSR1 to idle out, which should just return
immediately, so a very short (~1-2 usec) wait for cases where PSR
is disabled.

v2: Add comment to explain the 25msec timeout (DK)

v3: Rename psr_wait_for_idle to __psr_wait_for_idle_locked to avoid
    naming conflicts and propagate err (if any) to the caller (Chris)

v5: Form a series with the next patch

v7: Better explain the need for lockless wait and increase the max
    timeout to handle refresh rates < 60 Hz (Daniel Vetter)

v8: Rebase
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NTarun Vyas <tarun.vyas@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627200250.1515-1-tarun.vyas@intel.com

eDP spec states that sink device will do a short pulse in HPD
line when there is a PSR/PSR2 error that needs to be handled by
source, this is handling the first and most simples error:
DP_PSR_SINK_INTERNAL_ERROR.

Here taking the safest approach and disabling PSR(at least until
the next modeset), to avoid multiple rendering issues due to
bad pannels.

v5:
added lockdep_assert in psr_disable and renamed psr_disable()
to intel_psr_disable_locked()

v4:
Using CAN_PSR instead of HAS_PSR in intel_psr_short_pulse

v3:
disabling PSR instead of exiting on error
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626201644.21932-2-jose.souza@intel.com

So far we got an AUX power domain reference only for the duration of DP
AUX transfers. However, the following suggests that we also need these
for main link functionality:
- The specification doesn't state whether it's needed or not for main
  link functionality, but suggests that these power wells need to be
  enabled already during display core initialization (Sequences to
  Initialize Display).
- For PSR we need to keep the AUX power well enabled.
- On ICL combo PHY ports (non-TC) the AUX power well is needed for
  link training too: while the port is enabled with a DP link training
  test pattern trying to toggle the AUX power well will time out.
- On ICL MG PHY ports (TC) the AUX power well is needed also for main
  link functionality (both in DP and HDMI modes).
- Windows enables these power wells both for main and AUX lane
  functionality.

Based on the above take an AUX power reference for main link
functionality too. This makes a difference only on GEN10+ (GLK+)
platforms, where we have separate port specific AUX power wells.

For PSR we still need to distinguish between port A and the other
ports, since on port A DC states must stay enabled for main link
functionality, but DC states must be disabled for driver initiated
AUX transfers. So re-use the corresponding helper from intel_psr.c.

Since we take now a reference for main link functionality on all DP
ports we can forgo taking the separate power ref for PSR functionality.

v2:
- Make sure DC states stay enabled when taking the ref on port A.
  (Ville)

v3: (Ville)
- Fix comment about logic for encoders without a crtc state and
  add FIXME note for a simplification to avoid calling get_power_domains
  in such cases.
- Use intel_crtc_has_dp_encoder() instead !intel_crtc_has_type(HDMI).

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
[Clarified code comments in intel_ddi_main_link_aux_domain() and
 intel_ddi_get_power_domains() (Imre)]
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621184449.26634-1-imre.deak@intel.com

This became dead code with commit 309bd8ed ("drm/i915: Reinstate
GMBUS and AUX interrupts on gen4/g4x").

v2: Move comment about HW behavior to where decision is made to enable
MSI (Ville).

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180523180435.18042-1-lucas.demarchi@intel.com

No point in having this extra indireciton for the cursor max size.
So drop the defines and just write out the raw numbers. Makes it
easier to see what's going on.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615174406.12258-1-ville.syrjala@linux.intel.comReviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>

DP spec 1.4 supports training pattern set 4 (TPS4) for HBR3 link
rate. This will be used in link training's channel equalization
phase if supported by both source and sink.
This patch adds the helpers to check if HBR3 is supported and uses
TPS4 in training pattern selection during link training.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: NJames Ausmus <james.ausmus@intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611222655.5696-2-paulo.r.zanoni@intel.com

Add and enum for TC ports and auxiliary functions to handle them.
Icelake brings a lot of registers and other things that only apply to
the TC ports and are indexed starting from 0, so having an enum for
tc_ports that starts at 0 really helps the indexing.

This patch is based on previous patches written by Dhinakaran Pandiyan
and Mahesh Kumar.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: NMahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180522002558.29262-4-paulo.r.zanoni@intel.com

Set up the SKL+ scaler initial phase registers correctly. Otherwise
we start fetching the data from the center of the first pixel instead
of the top-left corner, which obviously then leads to right/bottom edges
replicating data excessively as the data runs out half a pixel too soon.

Cc: Vidya Srinivas <vidya.srinivas@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180521185613.5097-2-ville.syrjala@linux.intel.comReviewed-By: NVidya Srinivas <vidya.srinivas@intel.com>

Like we do for encoder let's make the plane->get_hw_state() return
the pipe to which the plane is currently attached. We don't currently
allow planes to move between the pipes, but perhaps one day we will.

In either case this makes the code more uniform and perhaps makes
intel_plane_mapping_ok() slightly more clear.

Note that for i965 and g4x planes A and B still have pipe select bits
but they're hardwired to pipe A and B respectively. This means we can
safely interpret those bits just like on gen2/3. This allows the
same readout code work for plane C (which can still be assigned
to eiter pipe on i965) should we ever expose it.

g4x no longer allows moving the cursor planes between the pipes,
but the pipe select bits can still be set in the register. Thus
we have to ignore those bits. OTOH i965 still allows the cursors
to move between pipes thus we have to trust the bits there.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130203807.13721-3-ville.syrjala@linux.intel.comReviewed-by: NMika Kahola <mika.kahola@intel.com>

This reverts commit dc911f5b.

Per the report, no matter what display mode you select with xrandr, the
i915 driver will always select the alternate fixed mode. For the
reporter this means that the display will always run at 40Hz which is
quite annoying. This may be due to the mode comparison.

But there are some other potential issues. The choice of alt_fixed_mode
seems dubious. It's the first non-preferred mode, but there are no
guarantees that the only difference would be refresh rate. Similarly,
there may be more than one preferred mode in the probed modes list, and
the commit changes the preferred mode selection to choose the last one
on the list instead of the first.

(Note that the probed modes list is the raw, unfiltered, unsorted list
of modes from drm_add_edid_modes(), not the pretty result after a
drm_helper_probe_single_connector_modes() call.)

Finally, we already have eerily similar code in place to find the
downclock mode for DRRS that seems like could be reused here.

Back to the drawing board.

Note: This is a hand-crafted revert due to conflicts. If it fails to
backport, please just try reverting the original commit directly.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105469Reported-by: NRune Petersen <rune@megahurts.dk>
Reported-by: NMark Spencer <n7u4722r35@ynzlx.anonbox.net>
Fixes: dc911f5b ("drm/i915/edp: Allow alternate fixed mode for eDP if available.")
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180516080110.22770-1-jani.nikula@intel.com
(cherry picked from commit d93fa1b4)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Up to now we've used the plane's modifier list as the primary
source of information for which modifiers are supported by a
given plane. In order to allow auxiliary metadata to be embedded
within the bits of the modifier we need to stop doing that.

Thus we have to make .format_mod_supported() aware of the plane's
capabilities and gracefully deal with any modifier being passed
in directly from userspace.

v2: Rebase after NV12
    Simplify

Cc: Eric Anholt <eric@anholt.net>
References: https://lists.freedesktop.org/archives/dri-devel/2018-March/169782.htmlSigned-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180518162159.30305-1-ville.syrjala@linux.intel.comReviewed-by: NEric Anholt <eric@anholt.net>

PSR hardware and hence the driver code for VLV and CHV deviates a lot from
their DDI counterparts. While the feature has been disabled for a long time
now, retaining support for these platforms is a maintenance burden. There
have been multiple refactoring commits to just keep the existing code for
these platforms in line with the rest. There are known issues that need to
be fixed to enable PSR on these platforms, and there is no PSR capable
platform in CI to ensure the code does not break again if we get around to
fixing the existing issues. On account of all these reasons, let's nuke
this code for now and bring it back if a need arises in the future.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180511230059.19387-1-dhinakaran.pandiyan@intel.com

Clean up the DP pipe select bits. To make the whole situation a bit
less ugly we'll start to share the same code between .get_hw_state(),
the port state asserts, and the VLV power sequencer code.

v2: Return PIPE_A for cpt/ppt when the port isn't selected by
    any transcoder. Returning INVALID_PIPE explodes *somewhere*
    on some machines (can't immediately see where though). This
    now matches the old behaviour.
v3: Order the defines shift,mask,value (Jani)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180518152931.13104-4-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>