- 16 5月, 2018 38 次提交
-
-
由 Yoshihiro Shimoda 提交于
The cache controller node should not have unit-addresses and reg properties. So, this patch removes them. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Yoshihiro Shimoda 提交于
The basic support patch 9491a8b17530 ("arm64: dts: renesas: Add Renesas R8A77990 SoC support") lacks the compatible "arm,psci-1.0" in the psci node. So, this patch revises it. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Simon Horman 提交于
Remove 'status = "disabled"' to make sure all IPMMU devices are enabled in DT on the r8a7795 ES1.0 Soc. This is a follow up for a patch by Magnus Damm for the the r8a7795 ES2.0 and other R-Car Gen 3 SoCs. Signed-off-by: NSimon Horman <horms+renesas@verge.net.au> Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Kuninori Morimoto 提交于
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-by: NNguyen Viet Dung <nv-dung@jinso.co.jp> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Kuninori Morimoto 提交于
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-by: NNguyen Viet Dung <nv-dung@jinso.co.jp> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Kuninori Morimoto 提交于
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-by: NNguyen Viet Dung <nv-dung@jinso.co.jp> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Kuninori Morimoto 提交于
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-by: NNguyen Viet Dung <nv-dung@jinso.co.jp> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Kuninori Morimoto 提交于
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-by: NNguyen Viet Dung <nv-dung@jinso.co.jp> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Kuninori Morimoto 提交于
Current Sound is using simple-audio-card which can't support HDMI. To use HDMI sound, we need to use audio-graph-card. But, one note is that r8a7795 has 2 HDMI ports, but r8a7796 has 1. Because of this mismatch, supporting HDMI on salvator-common is impossible. Thus, this patch exchange sound card to audio-graph-card and keep supporting ak4613 as 1st sound node. r8a7795/r8a7796 salvator-x{s} need to add HDMI sound individually. Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-by: NNguyen Viet Dung <nv-dung@jinso.co.jp> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Kuninori Morimoto 提交于
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-by: NNguyen Viet Dung <nv-dung@jinso.co.jp> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Kuninori Morimoto 提交于
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-by: NNguyen Viet Dung <nv-dung@jinso.co.jp> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Sergei Shtylyov 提交于
Define the generic R8A77980 part of the MMC0 (SDHI2) device node. Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Sergei Shtylyov 提交于
Add the (previously omitted) EtherAVB pin data to the Condor board's device tree. Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Sergei Shtylyov 提交于
Add the (previously omitted) SCIF0 pin data to the Condor board's device tree. Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Sergei Shtylyov 提交于
Define the generic R8A77980 part of the PFC device node. Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Sergei Shtylyov 提交于
Add the (previously omitted) EtherAVB pin data to the V3M Starter Kit board's device tree. Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Sergei Shtylyov 提交于
Add the (previously omitted) EtherAVB pin data to the Eagle board's device tree. Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Geert Uytterhoeven 提交于
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio" instead of "mdc". Fix the inconsistency, now the pinctrl drivers for R-Car H3, M3-W, and M3-N have gained support for the traditional pin group name. Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Geert Uytterhoeven 提交于
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio" instead of "mdc". Fix the inconsistency, now the pinctrl drivers for R-Car H3, M3-W, and M3-N have gained support for the traditional pin group name. Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Geert Uytterhoeven 提交于
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio" instead of "mdc". Fix the inconsistency, now the pinctrl drivers for R-Car H3, M3-W, and M3-N have gained support for the traditional pin group name. Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Magnus Damm 提交于
Remove 'status = "disabled"' to make sure all IPMMU devices are enabled in DT on the r8a77995 SoC. Signed-off-by: NMagnus Damm <damm+renesas@opensource.se> Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be> [simon: rebased] Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Magnus Damm 提交于
Remove 'status = "disabled"' to make sure all IPMMU devices are enabled in DT on the r8a77970 SoC. Signed-off-by: NMagnus Damm <damm+renesas@opensource.se> Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be> [simon: rebased] Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Magnus Damm 提交于
Remove 'status = "disabled"' to make sure all IPMMU devices are enabled in DT on the r8a7796 SoC. Signed-off-by: NMagnus Damm <damm+renesas@opensource.se> Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Magnus Damm 提交于
Remove 'status = "disabled"' to make sure all IPMMU devices are enabled in DT on the r8a7795 SoC. Signed-off-by: NMagnus Damm <damm+renesas@opensource.se> Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Takeshi Kihara 提交于
Basic support for the Renesas Ebisu board based on R-Car E3: - Memory, - Main crystal, - Serial console, Signed-off-by: NTakeshi Kihara <takeshi.kihara.df@renesas.com> [shimoda: rebase and add SPDX-License-Identifier] Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Yoshihiro Shimoda 提交于
This patch adds basic support for the Renesas R-Car E3 (R8A77990) SoC: - PSCI - CPU (single) - Cache controller - Main clocks and controller - Interrupt controller - Timer - PMU - Reset controller - Product register - System controller - UART for console Inspried by a patch by Takeshi Kihara in the BSP. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Yoshihiro Kaneko 提交于
Sort subnodes of the soc node. - The primary key is the bus address. - The secondary key is the IP block. - The tertiary key is the node name. This is part of an ongoing effort to provide consistent node order in the DT of Renesas SoCs to improve maintainability. This should not have any run-time effect. Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com> [simon: rebased; move fcpvd0 to after vspd0] Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Yoshihiro Kaneko 提交于
Sort subnodes of the soc node. - The primary key is the bus address. - The secondary key is the IP block. - The tertiary key is the node name. This is part of an ongoing effort to provide consistent node order in the DT of Renesas SoCs to improve maintainability. This should not have any run-time effect. Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Yoshihiro Kaneko 提交于
Sort subnodes of the root node alphanumerically. This is part of an ongoing effort to provide consistent node order in the DT of Renesas SoCs to improve maintainability. This should not have any run-time effect. Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Yoshihiro Kaneko 提交于
Sort subnodes of the soc node. - The primary key is the bus address. - The secondary key is the IP block. - The tertiary key is the node name. This is part of an ongoing effort to provide consistent node order in the DT of Renesas SoCs to improve maintainability. This should not have any run-time effect. Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Yoshihiro Kaneko 提交于
Sort subnodes of the root node alphanumerically. This is part of an ongoing effort to provide consistent node order in the DT of Renesas SoCs to improve maintainability. This should not have any run-time effect. Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Jacopo Mondi 提交于
Enable HDMI output on Renesas R-Car V3M Eagle board. The HDMI output is enabled connecting the DU LVDS output to the transparent LVDS converter THC63LVD1024, and successively routing its RGB output to the ADV7511W HDMI encoder. Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: NJacopo Mondi <jacopo+renesas@jmondi.org> Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com> [for THC63LVD1024: ] Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Sergei Shtylyov 提交于
Define the generic R8A77970 part of the LVDS device node. Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Sergei Shtylyov 提交于
Define the generic R8A77970 part of the DU device node. Based on the original (and large) patch by Daisuke Matsushita <daisuke.matsushita.ns@hitachi.com>. Signed-off-by: NVladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Sergei Shtylyov 提交于
Describe VSPD0 in the R8A77970 device tree; it will be used by DU in the next patch... Based on the original (and large) patch by Daisuke Matsushita <daisuke.matsushita.ns@hitachi.com>. Signed-off-by: NVladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: NJacopo Mondi <jacopo+renesas@jmondi.org> Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Niklas Söderlund 提交于
To incorporate more tests by the hardware team decrease the hysteresis value to 1C. Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Niklas Söderlund 提交于
To incorporate more tests by the hardware team decrease the hysteresis value to 1C. Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Yoshihiro Shimoda 提交于
Add configuration option for the R-Car E3 (R8A77990) SoC. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
- 16 4月, 2018 2 次提交
-
-
由 Sergei Shtylyov 提交于
Describe FCPVD0 in the R8A77970 device tree; it will be used by VSPD0 in the next patch... Based on the original (and large) patch by Daisuke Matsushita <daisuke.matsushita.ns@hitachi.com>. Signed-off-by: NVladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-
由 Yoshihiro Shimoda 提交于
This patch adds PWM device nodes for r8a77965. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
-