We don't track gpu flush request in any special way. So even with
obj->write_domain == 0, a gpu flush might be outstanding but no
yet executed. Even worse, the latest request might use the object
only for reading. So and unconditional call to object_wait_rendering
is needed for !pipelined.

Hence revert that patch fully and untangle the flushing from the
synchronization again.
Reported-by: NKeith Packard <keithp@keithp.com>
Tested-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Commit d09c23de intended to add a 30ms delay to give the ADD time to
detect any TVs connected. However, it used the sdvo->is_tv flag to do so
which is dependent upon the previous detection result and not whether the
output supports TVs.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

On a few devices, like the Mac Mini, the CRT DDC pins are shared between
the analog connector and the digital connector. In this scenario, rely
on the EDID to determine if a digital panel is connected to the digital
connector.
Reported-and-tested-by: NTino Keitel <tino.keitel@tikei.de>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Currently if we hit a pagefault when applying a user relocation for the
execbuffer, we bail and return EFAULT to the application. Instead, we
need to unwind, drop the dev->struct_mutex, copy all the relocation
entries to a vmalloc array (to avoid any potential circular deadlocks
when resolving the pagefault), retake the mutex and then apply the
relocations.  Afterwards, we need to again drop the lock and copy the
vmalloc array back to userspace.

v2: Incorporate feedback from Daniel Vetter.
Reported-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As we conflated intel_sdvo->is_hdmi with both having HDMI support on the
ADD along with having HDMI support on the monitor, we would attempt to
use HDMI encodings even if the interface did not support those commands.
Reported-by: NSimon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NSimon Farnsworth <simon.farnsworth@onelan.co.uk>
Reviewed-by: NSimon Farnsworth <simon.farnsworth@onelan.co.uk>

Under KMS, restoring the cursor is handled upon modeswitch in order to
avoid enabling an undefined set of registers. At the moment, the cursor
is restored before the aperture and modes are fully setup causing some
invalid access during resume, such as:

  PGTBL_ER: 0x00040000
    Invalid GTT entry during Cursor Fetch

Fix this by only performing cursor register save/restore under UMS where
it is done in the correct sequence.
Reported-by: NArkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Commit 2549d6c2 removed the vmalloc used for temporary storage of the
relocation lists used during execbuffer. However, our use of vmalloc was
being protected by an integer overflow check which we do want to
preserve!
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Frame buffer compression is broken on Ironlake due to buggy hardware.
Currently it is disabled through chicken bits, but it still consumes
over 1W more than if we simply never attempt to enable the FBC code
paths.
Signed-off-by: NAlex Shi <alex.shi@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

Both IBX and CPT have an automatic hotplug detection mode which appears to work reliably enough
that we can dispense with the manual force hotplug trigger stuff. This means that
hotplug detection is as simple as reading the current hotplug register values.

The first time the hotplug detection is activated, the code synchronously waits for a hotplug
sequence in case the hardware hasn't bothered to do a detection cycle since being initialized.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

We will use this structure in future patches to store CRT specific
information on the encoder.

Split out and tweaked from a patch by Keith Packard.
Signed-off-by: NKeith Packard <keithp@kithp.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Linus Torvalds found that it was rather trivial to trigger a system
freeze:

  In fact, with lockdep, I don't even need to do the sysrq-d thing: it
  shows the bug as it happens. It's the X server taking the same lock
  recursively.

  Here's the problem:

    =============================================
    [ INFO: possible recursive locking detected ]
    2.6.37-rc2-00012-gbdbd01ac #7
    ---------------------------------------------
    Xorg/2816 is trying to acquire lock:
     (&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c626c>] i915_gem_fault+0x50/0x17e

    but task is already holding lock:
     (&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c403b>] i915_mutex_lock_interruptible+0x28/0x4a

    other info that might help us debug this:
    2 locks held by Xorg/2816:
     #0:  (&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c403b>] i915_mutex_lock_interruptible+0x28/0x4a
     #1:  (&mm->mmap_sem){++++++}, at: [<ffffffff81022d4f>] page_fault+0x156/0x37b

This recursion was introduced by rearranging the locking to avoid the
double locking on the fast path (4f27b5d and fbd5a26d) and the
introduction of the prefault to encourage the fast paths (b5e4f2b). In
order to undo the problem, we rearrange the code to perform the access
validation upfront, attempt to prefault and then fight for control of the
mutex.  the best case scenario where the mutex is uncontended the
prefaulting is not wasted.
Reported-and-tested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

As per advice from Jean Delvare.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

These got lost in the last i2c cleanup.  Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=23222Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

A process suspended waiting for a higher sequence or no sequence to unreserve,
a bo may be beaten to the reservation by a process with a lower sequence.
In that case the first process should give up trying to reserve and
return -EAGAIN. In order for that to happen, we must wake waiting processes
when we change sequence, so that they have a chance to detect the new
sequence.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We aren't currently using tiling in userspace on evergreen,
but the info we currently return for the tiling info query
(gb_addr_config) is no adequate for userspace tiling alignment
calculations.  It does not contain the bank info.  Create a custom
tiling info dword with all the necessary info (num channels,
num banks, group size, row size).
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We were previously dropping alignment requests on the floor
when allocating buffers so we always ended up page aligned.
Certain tiling modes on 6xx+ require larger alignment which
wasn't happening before.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <j.glisse@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This causes the connector to not be added since i2c init fails
for the adapter.  Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=31688

Noticed by Ari Savolainen.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: Ari Savolainen <ari.m.savolainen@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

These are external encoder chips connected via DVO or DP.
The actual external encoder programming is handled by the
kms encoder functions for primary encoder.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Handle all the various asic family specific things for DVO.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The eDP panel must be powered up for aux transactions, so power it
up for detect and mode probe functions, otherwise power it up or
down based on dpms.

v2:
- only mess with eDP panel on DCE4+
- only mess with eDP panel on eDP connectors, not all DP connectors
v3:
- be extra careful to only mess with eDP panels on eDP connectors
v4:
- avoid possible null derefernce if a connector has not been
assigned to the encoder
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If there was no connector mapped to the encoder, atombios_get_encoder_mode()
returned 0 which is the id for DP.  Return something sane instead based on
the encoder id.  This avoids hitting the DP paths on non-DP encoders.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Seems some newer systems require this explicitly.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Looks like a typo in:
drm/radeon/r600: fix tiling issues in CS checker.
(f30df2fa)
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

enable_vblank implementations should use negative result to indicate error.
radeon_enable_vblank() returns EINVAL in this case.  Change this to -EINVAL.
Signed-off-by: NVasiliy Kulikov <segoon@openwall.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Tiled buffers have the same alignment requirements regardless of
whether the surface is for db, cb, or textures.  Previously, the
calculations where inconsistent for each buffer type.

- Unify the alignment calculations in a common function
- Standardize the alignment units (pixels for pitch/height/depth,
bytes for base)
- properly check the buffer base alignments
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The old code generated an interrupt storm bad enough to completely
take down my system.
Signed-off-by: NAndy Lutomirski <luto@mit.edu>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Avoid confusing userspace by not publishing backlight controls if ACPI
equivalents are available.
Reported-by: NAaron Sowry <aaron@aeneby.se>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Improvements:
 - Fix bug in switch statement
 - Add parts of 0x10022c, 0x10023c
 - Clean up 0x100234
 - Comment out assumption in 0x100228 until verified
Signed-off-by: NRoy Spliet <r.spliet@student.tudelft.nl>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reported-by: NTomas Miljenovic <tomasmiljenovic@gmail.com>
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reported-by: NTomas Miljenovic <tomasmiljenovic@gmail.com>
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NMartin Peres <martin.peres@ensi-bourges.fr>
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Analog output polling makes GL programs jerky when pageflip is being
used because it's carried out with the mode_config mutex held.
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reported-by: NXavier Chantry <chantry.xavier@gmail.com>
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Nouveau sets the PCIE GART size to 64MiB for all cards before nv50,
but nv40 has enough RAMIN space to support 512MiB GART size. This
patch fixes this value to make use of this hardware capability.
Signed-off-by: NLucas Stach <dev@lynxeye.de>
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>