It is possible that the interface is already gone after joining
the list of anycast on this interface as we don't hold a refcount
for the device, in this case we are safe to ignore the error.

What's more important, for API compatibility we should not
change this behavior for applications even if it were correct.

Fixes: commit a9ed4a29 ("ipv6: fix rtnl locking in setsockopt for anycast and multicast")
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tom Lendacky says:

====================
amd-xgbe: AMD XGBE driver fixes 2014-09-05

The following series of patches includes fixes to the driver.

- Proper access to 64 bit management counter registers
- Enable all management counter registers to generate an interrupt when
  the counter threshold is reached

This patch series is based on net.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the management counters reach a threshold they will generate an
interrupt so the value can be saved and the counter reset. The
current code does not enable this interrupt on all counters. This
can result in inaccurate statistics.

Update the code to enable all the counters to generate an interrupt
when its threshold is exceeded.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Even if the management counters are configured to be 32 bit register
values, the [rt]xoctetcount_gb and [rt]xoctetcount_g counters are
always 64 bit counter registers.  Since they are not being treated as
64 bit values, these statistics are being reported incorrectly (ifconfig,
ethtool, etc.).

Update the routines used to read the registers to access the "hi"
register (an offset of 4 from the "lo" register) to create a 64 bit
value for these 64 bit counters.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch does not affect the 10/100 GRETH MAC.

Before all GBit GRETH TX descriptor ring cleaning was done in
start_xmit(), when descriptor list became full it activated
TX interrupt to start the NAPI rx poll function to do TX ring
cleaning.

With this patch the TX descriptor ring is always cleaned from
the NAPI rx poll function, triggered via TX or RX interrupt.
Otherwise we could end up in TX frames being sent but not
reported to the stack being sent. On the 10/100 GRETH this
is not an issue since the SKB is copied&aligned into private
buffers so that the SKB can be freed directly on start_xmit()
Signed-off-by: NDaniel Hellstrom <daniel@gaisler.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cnic module needs to ensure that if ipv6 support is compiled as a module,
then the cnic module cannot be compiled as built-in as it depends on ipv6.
Made this check cleaner via Kconfig

Use simpler IS_ENABLED for CONFIG_VLAN_8021Q check
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fix spelling typo found in DocBook/networking.xml.
It is because the neworking.xml is generated from comments
in the source, I have to fix typo in comments within the source.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When 1G SFP RJ45 module is detected, driver must reset the Tx laser
in order to prevent link issues. As part of change, the link_attr_sync
was relocated from vars to params.
Signed-off-by: NYaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This bug was reported on a very old kernel (RHEL6, 2.6.32-491.el6):

BUG: unable to handle kernel paging request at 00800000
IP: [<c04107b5>] nommu_map_page+0x15/0x110
*pdpt = 000000003454f001 *pde = 000000003f03d067
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/system/cpu/online
Modules linked in: nfsd lockd nfs_acl auth_rpcgss sunrpc exportfs p4_clockmod
ipv6 ppdev parport_pc parport microcode iTCO_wdt iTCO_vendor_support 3c59x mii
dcdbas serio_raw snd_intel8x0 snd_ac97_codec ac97_bus snd_seq snd_seq_device
snd_pcm snd_timer snd soundcore snd_page_alloc i2c_i801 sg lpc_ich mfd_core ext4
jbd2 mbcache sr_mod cdrom sd_mod crc_t10dif pata_acpi ata_generic ata_piix
radeon ttm drm_kms_helper drm i2c_algo_bit i2c_core dm_mirror dm_region_hash
dm_log dm_mod [last unloaded: mperf]

Pid: 4219, comm: nfsd Not tainted 2.6.32-491.el6.i686 #1 Dell Computer
Corporation OptiPlex GX240               /OptiPlex GX240
EIP: 0060:[<c04107b5>] EFLAGS: 00010246 CPU: 0
EIP is at nommu_map_page+0x15/0x110
EAX: 00000000 EBX: c0a83480 ECX: 00000000 EDX: 00800000
ESI: 00000000 EDI: f70e7860 EBP: e2d09b54 ESP: e2d09b24
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process nfsd (pid: 4219, ti=e2d08000 task=e2ceaaa0 task.ti=e2d08000)
Stack:
 00000056 00000000 0000000e c65efd38 00000020 00000296 00000206 00000206
<0> c050c850 c0a83480 e2cef154 00000001 e2d09ba8 f8fcd585 00000510 00000001
<0> 00000000 00000000 f5172200 f8fdac00 0039ef8c f5277020 f70e7860 00000510
Call Trace:
 [<c050c850>] ? page_address+0xd0/0xe0
 [<f8fcd585>] ? boomerang_start_xmit+0x3b5/0x520 [3c59x]
 [<c07b2975>] ? dev_hard_start_xmit+0xe5/0x400
 [<f9182b00>] ? ip6_output_finish+0x0/0xf0 [ipv6]
 [<c07ca053>] ? sch_direct_xmit+0x113/0x180
 [<c07d5588>] ? nf_hook_slow+0x68/0x120
 [<c07b2ea5>] ? dev_queue_xmit+0x1b5/0x290
 [<f9182b6d>] ? ip6_output_finish+0x6d/0xf0 [ipv6]
 [<f9184cb8>] ? ip6_xmit+0x3e8/0x490 [ipv6]
 [<f91ab9f9>] ? inet6_csk_xmit+0x289/0x2f0 [ipv6]
 [<c07f6451>] ? tcp_transmit_skb+0x431/0x7f0
 [<c07a403f>] ? __alloc_skb+0x4f/0x140
 [<c07f85a2>] ? tcp_write_xmit+0x1c2/0xa50
 [<c07f90b1>] ? __tcp_push_pending_frames+0x31/0xe0
 [<c07ea47a>] ? tcp_sendpage+0x44a/0x4b0
 [<c07ea030>] ? tcp_sendpage+0x0/0x4b0
 [<c079be1e>] ? kernel_sendpage+0x4e/0x90
 [<f8457bb9>] ? svc_send_common+0xc9/0x120 [sunrpc]
 [<f8457c85>] ? svc_sendto+0x75/0x1f0 [sunrpc]
 [<c060d0d9>] ? _atomic_dec_and_lock+0x59/0x90
 [<f87d55d0>] ? nfs3svc_encode_readres+0x0/0xc0 [nfsd]
 [<f845876d>] ? svc_authorise+0x2d/0x40 [sunrpc]
 [<f87d4410>] ? nfs3svc_release_fhandle+0x0/0x10 [nfsd]
 [<f8455721>] ? svc_process_common+0xf1/0x5a0 [sunrpc]
 [<f8457e86>] ? svc_tcp_sendto+0x36/0xa0 [sunrpc]
 [<f8461778>] ? svc_send+0x98/0xd0 [sunrpc]
 [<f87c698c>] ? nfsd+0xac/0x140 [nfsd]
 [<c04470e0>] ? complete+0x40/0x60
 [<f87c68e0>] ? nfsd+0x0/0x140 [nfsd]
 [<c04802ac>] ? kthread+0x7c/0xa0
 [<c0480230>] ? kthread+0x0/0xa0
 [<c0409f9f>] ? kernel_thread_helper+0x7/0x10
Code: 8d b6 00 00 00 00 eb f8 8d b4 26 00 00 00 00 8d bc 27 00 00 00 00 55 89 e5
83 ec 30 89 75 f8 31 f6 89 7d fc 89 c7 89 c8 89 5d f4 <8b> 1a 8b 4d 08 c1 eb 19
c1 e3 04 8b 9b c0 29 c7 c0 83 e3 fc 29

But the problem seems to still exist upstream.  It seems on 32 bit kernels
page_address() can reutrn a NULL value in some circumstances, and the
pci_map_single api isn't prepared to handle that (on this system it results in a
bogus pointer deference in nommu_map_page.

The fix is pretty easy, if we convert the 3c59x driver to use the more
convieient skb_frag_dma_map api we don't need to find the virtual address of the
page at all, and page gets mapped to the hardware properly.  Verified to fix the
problem as described by the reporter.

Applies to the net tree

Change Notes:

v2) Converted PCI_DMA_TODEVICE to DMA_TO_DEVICE.  Thanks Dave!

v3) Actually Run git commit after making changes to v2 :)
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: klassert@mathematik.tu-chemnitz.de
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Paul Bolle reports that 'select NETFILTER_XT_NAT' from the IPV4 and IPV6
NAT tables becomes noop since there is no Kconfig switch for it. Add the
Kconfig switch to resolve this problem.

Fixes: 8993cf8e netfilter: move NAT Kconfig switches out of the iptables scope
Reported-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

addrconf_get_prefix_route() ensures to get the right route in the right table.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no reason to take a refcnt before deleting the peer address route.
It's done some lines below for the local prefix route because
inet6_ifa_finish_destroy() will release it at the end.
For the peer address route, we want to free it right now.

This bug has been introduced by commit
caeaba79 ("ipv6: add support of peer address").
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The timestamping API has separate bits for generating and reporting
timestamps. A software timestamp should only be reported for a packet
when the packet has the relevant generation flag (SKBTX_..) set
and the socket has reporting bit SOF_TIMESTAMPING_SOFTWARE set.

The second check was accidentally removed. Reinstitute the original
behavior.

Tested:
  Without this patch, Documentation/networking/txtimestamp reports
  timestamps regardless of whether SOF_TIMESTAMPING_SOFTWARE is set.
  After the patch, it only reports them when the flag is set.

Fixes: f24b9be5 ("net-timestamp: extend SCM_TIMESTAMPING ancillary data struct")
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

They are use less, and may generate compiling warnings, so remove them
(microblaze, arc, arm64, and unicore32 have already defined PCI_IOBASE).

The related warnings (with allmodconfig under microblaze):

  CC [M]  drivers/net/fddi/skfp/skfddi.o
  In file included from drivers/net/fddi/skfp/skfddi.c:95:0:
  drivers/net/fddi/skfp/h/skfbi.h:151:0: warning: "PCI_IOBASE" redefined
   #define PCI_IOBASE 0xffffff00L  /* Bit 31..8:  I/O Base address */
   ^
  In file included from include/linux/io.h:22:0,
                   from include/linux/pci.h:31,
                   from drivers/net/fddi/skfp/skfddi.c:82:
  ./arch/microblaze/include/asm/io.h:33:0: note: this is the location of the previous definition
   #define PCI_IOBASE ((void __iomem *)_IO_BASE)
   ^
Signed-off-by: NChen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use dst_entry held by sk_dst_get() to retrieve tunnel's PMTU.

The dst_mtu(__sk_dst_get(tunnel->sock)) call was racy. __sk_dst_get()
could return NULL if tunnel->sock->sk_dst_cache was reset just before the
call, thus making dst_mtu() dereference a NULL pointer:

[ 1937.661598] BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
[ 1937.664005] IP: [<ffffffffa049db88>] pppol2tp_connect+0x33d/0x41e [l2tp_ppp]
[ 1937.664005] PGD daf0c067 PUD d9f93067 PMD 0
[ 1937.664005] Oops: 0000 [#1] SMP
[ 1937.664005] Modules linked in: l2tp_ppp l2tp_netlink l2tp_core ip6table_filter ip6_tables iptable_filter ip_tables ebtable_nat ebtables x_tables udp_tunnel pppoe pppox ppp_generic slhc deflate ctr twofish_generic twofish_x86_64_3way xts lrw gf128mul glue_helper twofish_x86_64 twofish_common blowfish_generic blowfish_x86_64 blowfish_common des_generic cbc xcbc rmd160 sha512_generic hmac crypto_null af_key xfrm_algo 8021q garp bridge stp llc tun atmtcp clip atm ext3 mbcache jbd iTCO_wdt coretemp kvm_intel iTCO_vendor_support kvm pcspkr evdev ehci_pci lpc_ich mfd_core i5400_edac edac_core i5k_amb shpchp button processor thermal_sys xfs crc32c_generic libcrc32c dm_mod usbhid sg hid sr_mod sd_mod cdrom crc_t10dif crct10dif_common ata_generic ahci ata_piix tg3 libahci libata uhci_hcd ptp ehci_hcd pps_core usbcore scsi_mod libphy usb_common [last unloaded: l2tp_core]
[ 1937.664005] CPU: 0 PID: 10022 Comm: l2tpstress Tainted: G           O   3.17.0-rc1 #1
[ 1937.664005] Hardware name: HP ProLiant DL160 G5, BIOS O12 08/22/2008
[ 1937.664005] task: ffff8800d8fda790 ti: ffff8800c43c4000 task.ti: ffff8800c43c4000
[ 1937.664005] RIP: 0010:[<ffffffffa049db88>]  [<ffffffffa049db88>] pppol2tp_connect+0x33d/0x41e [l2tp_ppp]
[ 1937.664005] RSP: 0018:ffff8800c43c7de8  EFLAGS: 00010282
[ 1937.664005] RAX: ffff8800da8a7240 RBX: ffff8800d8c64600 RCX: 000001c325a137b5
[ 1937.664005] RDX: 8c6318c6318c6320 RSI: 000000000000010c RDI: 0000000000000000
[ 1937.664005] RBP: ffff8800c43c7ea8 R08: 0000000000000000 R09: 0000000000000000
[ 1937.664005] R10: ffffffffa048e2c0 R11: ffff8800d8c64600 R12: ffff8800ca7a5000
[ 1937.664005] R13: ffff8800c439bf40 R14: 000000000000000c R15: 0000000000000009
[ 1937.664005] FS:  00007fd7f610f700(0000) GS:ffff88011a600000(0000) knlGS:0000000000000000
[ 1937.664005] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 1937.664005] CR2: 0000000000000020 CR3: 00000000d9d75000 CR4: 00000000000027e0
[ 1937.664005] Stack:
[ 1937.664005]  ffffffffa049da80 ffff8800d8fda790 000000000000005b ffff880000000009
[ 1937.664005]  ffff8800daf3f200 0000000000000003 ffff8800c43c7e48 ffffffff81109b57
[ 1937.664005]  ffffffff81109b0e ffffffff8114c566 0000000000000000 0000000000000000
[ 1937.664005] Call Trace:
[ 1937.664005]  [<ffffffffa049da80>] ? pppol2tp_connect+0x235/0x41e [l2tp_ppp]
[ 1937.664005]  [<ffffffff81109b57>] ? might_fault+0x9e/0xa5
[ 1937.664005]  [<ffffffff81109b0e>] ? might_fault+0x55/0xa5
[ 1937.664005]  [<ffffffff8114c566>] ? rcu_read_unlock+0x1c/0x26
[ 1937.664005]  [<ffffffff81309196>] SYSC_connect+0x87/0xb1
[ 1937.664005]  [<ffffffff813e56f7>] ? sysret_check+0x1b/0x56
[ 1937.664005]  [<ffffffff8107590d>] ? trace_hardirqs_on_caller+0x145/0x1a1
[ 1937.664005]  [<ffffffff81213dee>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[ 1937.664005]  [<ffffffff8114c262>] ? spin_lock+0x9/0xb
[ 1937.664005]  [<ffffffff813092b4>] SyS_connect+0x9/0xb
[ 1937.664005]  [<ffffffff813e56d2>] system_call_fastpath+0x16/0x1b
[ 1937.664005] Code: 10 2a 84 81 e8 65 76 bd e0 65 ff 0c 25 10 bb 00 00 4d 85 ed 74 37 48 8b 85 60 ff ff ff 48 8b 80 88 01 00 00 48 8b b8 10 02 00 00 <48> 8b 47 20 ff 50 20 85 c0 74 0f 83 e8 28 89 83 10 01 00 00 89
[ 1937.664005] RIP  [<ffffffffa049db88>] pppol2tp_connect+0x33d/0x41e [l2tp_ppp]
[ 1937.664005]  RSP <ffff8800c43c7de8>
[ 1937.664005] CR2: 0000000000000020
[ 1939.559375] ---[ end trace 82d44500f28f8708 ]---

Fixes: f34c4a35 ("l2tp: take PMTU from tunnel UDP socket")
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling setsockopt with IPV6_JOIN_ANYCAST or IPV6_LEAVE_ANYCAST
triggers the assertion in addrconf_join_solict()/addrconf_leave_solict()

ipv6_sock_ac_join(), ipv6_sock_ac_drop(), ipv6_sock_ac_close() need to
take RTNL before calling ipv6_dev_ac_inc/dec. Same thing with
ipv6_sock_mc_join(), ipv6_sock_mc_drop(), ipv6_sock_mc_close() before
calling ipv6_dev_mc_inc/dec.

This patch moves ASSERT_RTNL() up a level in the call stack.
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Reported-by: NTommi Rantala <tt.rantala@gmail.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should check if the map of the table actually succeeds, and also free
resources accordingly.

Version bumped to 1.2.1.0
Acked-by: NShelley Gong <shelleygong@vmware.com>
Acked-by: NBhavesh Davda <bhavesh@vmware.com>
Signed-off-by: NAndy King <acking@vmware.com>
Reported-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

distinguish between the dropped and consumed skb, not assume the skb
is consumed always

Cc: Thomas Graf <tgraf@noironetworks.com>
Cc: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Acked-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During allocation and initialization of the network driver structures,
the wrong pointer is used to initialize a spin lock. Fix the spin lock
initialization by using the proper pointer.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The user_skb maybe be leaked if the operation on it failed and codes
skipped into the label "out:" without calling genlmsg_unicast.

Cc: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Acked-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

make defconfig reports:

warning: (NETFILTER_XT_TARGET_LOG) selects NF_LOG_IPV6 which has unmet direct dependencies (NET && INET && IPV6 && NETFILTER && NETFILTER_ADVANCED)

Fixes: d79a61d6 netfilter: NETFILTER_XT_TARGET_LOG selects NF_LOG_*
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
pull request: Netfilter/IPVS fixes for net

The following patchset contains seven Netfilter fixes for your net
tree, they are:

1) Make the NAT infrastructure independent of x_tables, some users are
   already starting to test nf_tables with NAT without enabling x_tables.
   Without this patch for Kconfig, there's a superfluous dependency
   between NAT and x_tables.
2) Allow to use 0 in the cgroup match, the kernel rejects with -EINVAL
   with no good reason. From Daniel Borkmann.

3) Select CONFIG_NF_NAT from the nf_tables NAT expression, this also
   resolves another NAT dependency with x_tables.

4) Use HAVE_JUMP_LABEL instead of CONFIG_JUMP_LABEL in the Netfilter hook
   code as elsewhere in the kernel to resolve toolchain problems, from
   Zhouyi Zhou.

5) Use iptunnel_handle_offloads() to set up tunnel encapsulation
   depending on the offload capabilities, reported by Alex Gartrell
   patch from Julian Anastasov.

6) Fix wrong family when registering the ip_vs_local_reply6() hook,
   also from Julian.

7) Select the NF_LOG_* symbols from NETFILTER_XT_TARGET_LOG. Rafał
   Miłecki reported that when jumping from 3.16 to 3.17-rc, his log
   target is not selected anymore due to changes in the previous
   development cycle to accomodate the full logging support for
   nf_tables.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some hosts can be both little and big endian.
In certain scenarios a big endian kernel can kexec a little endian kernel.

This patch fixes this case from both ends:
1) Return endianity to original values on shutdown (in case little endian kernel boots after we shutdown).
2) Do not rely on HW reset values when loading driver in little endian kernel
   but configure them explicitly (in case previous kernel was big endian and did not reset the HW).
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When qeth device is queried for ethtool data, hardware operation
is performed to extract the necessary information from the card.
If the card is not online at the moment (e.g. it is undergoing
recovery), this operation produces undesired effects like
temporarily freezing the system. This patch prevents execution
of the hardware query operation when the card is not online.
In such case, ioctl() operation returns error with errno ENODEV.
Reviewed-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NFrank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calxeda 1G/10G XGMAC Ethernet support should be available only on
Calxeda ECX-1000/2000 (Highbank/Midway) platforms.
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Renesas SuperH Ethernet support should be available only on
Renesas ARM SoCs and SuperH architecture.
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a link is already up, the following sequence makes the kernel
block completely:

  ip link set dev eth0 down
  ip link set dev eth0 up

This is because on suspended phy, the following lines

  __lpc_eth_reset(pldat);
  __lpc_eth_init(pldat);

make the LPC ethernet core block (see LPC32x0 manual). The PHY needs to be
(re-)activated low-level first.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch fixes race conditions between PCI error recovery callbacks and
potential ifup/ifdown.

First, if ifup (tg3_open) is called between tg3_io_error_detected() and
tg3_io_resume() then tp->timer is armed twice before expiry. Once during
tg3_open() and again during tg3_io_resume(). This results in BUG
at kernel/time/timer.c:945.

Second, if ifdown (tg3_close) is called between tg3_io_error_detected()
and tg3_io_resume() then tg3_napi_disable() is called twice without
a tg3_napi_enable between. Once during tg3_io_error_detected() and again
during tg3_close(). The tg3_io_resume() then hangs on rtnl_lock().

v2: Added logging messages per Prashant's request

Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NPrashant Sreedharan <prashant@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
Trivial fixes for cxgb4

This patch series adds support to fix T5 adapter accessing T4 adapter registers,
issue mbox command on correct mbox for physical function, avoid dumping write
only registers, use correct length for adapter part number and support to detect
and display firmware reported errors.

The patches series is created against 'net' tree.
And includes patches on cxgb4 driver.

We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.

Thanks

V2:
   Added description for each patch as per David Miller's comment
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A couple of RDMA-related called to t4_query_params() were issuing mbox commands
on mbox0 instead of mbox4.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid dumping MPS_RPLC_MAP_CTL for reg dumps; this is a Write-Only register.
Reading this register may cause MPS TCAM corruption.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The adapter firmware can indicate error conditions to the host.
If the firmware has indicated an error, print out the reason for
the firmware error.

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes few register access for both T4 and T5.
PCIE_CORE_UTL_SYSTEM_BUS_AGENT_STATUS & PCIE_CORE_UTL_PCI_EXPRESS_PORT_STATUS
is T4 only register don't let T5 access them. For T5 MA_PARITY_ERROR_STATUS2
is additionally read. MPS_TRC_RSS_CONTROL is T4 only register, for T5 use
MPS_T5_TRC_RSS_CONTROL.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously it was using the length value of serial number.
Also added macro for VPD unique identifier (0x82).
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We previously assumed that a Port's Capabilities and Advertised Capabilities
would never change from Port Initialization time.  This is no longer true
when we can have 10Gb/s and 1Gb/s SFP+ Transceiver Modules randomly swapped.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of the HW is not able to do the receive checksum offloading
the only feature to remove is NETIF_F_RXCSUM.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For new GMACs it is possible to turn-on/off the COE.
In the current driver, when disabled the Rx-checksum
via ethtool, the tool reported that csum was disabled
but the HW continued to set the IPC. Indeed this is
because the fix_features allows this. So the patch
fixes this problem by adding the set_features.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tom Lendacky says:

====================
amd-xgbe: AMD XGBE driver fixes 2014-08-29

The following series of patches includes fixes to the driver.

- Tx hardware queue flushing support dependent on hardware version
- Incorrect reported fifo size
- Proper mmd select in XPCS debugfs support
- Proper queue count for configuring Tx flow control

This patch series is based on net.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When configuring Tx flow control the Rx queue count was used instead of
the Tx queue count for looping through the Tx hardware queues. Fix the
code to use the Tx queue count.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The debugfs support for the xpcs registers did not properly use the
specified mmd (xpcs_mmd entry) which resulted in the default mmd
value always being used.  Update the debugfs support to generate the
proper mmd register value.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>