This patch basically replaces legacy adv with extended adv
based on the controller support. Currently there is no
design change. ie only one adv set will be enabled at a time.

This also adds tx_power in instance and store whatever returns
from Set_ext_parameter, use the same in adv data as well.
For instance 0 tx_power is stored in hdev only.

< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
        Handle: 0x00
        Properties: 0x0010
          Use legacy advertising PDUs: ADV_NONCONN_IND
        Min advertising interval: 1280.000 msec (0x0800)
        Max advertising interval: 1280.000 msec (0x0800)
        Channel map: 37, 38, 39 (0x07)
        Own address type: Random (0x01)
        Peer address type: Public (0x00)
        Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
        Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
        TX power: 127 dbm (0x7f)
        Primary PHY: LE 1M (0x01)
        Secondary max skip: 0x00
        Secondary PHY: LE 1M (0x01)
        SID: 0x00
        Scan request notifications: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 5
      LE Set Extended Advertising Parameters (0x08|0x0036) ncmd 1
        Status: Success (0x00)
        TX power (selected): 7 dbm (0x07)
< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 6
        Extended advertising: Enabled (0x01)
        Number of sets: 1 (0x01)
        Entry 0
          Handle: 0x00
          Duration: 0 ms (0x00)
          Max ext adv events: 0
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
        Status: Success (0x00)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch reads the number of advertising sets in the controller
during init and save it in hdev.
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch defines the extended ADV types and handle it in ADV report.
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Use the PHYs selected in Set Phy Configuration management command
while scanning.

< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 13
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement (0x00)
        PHYs: 0x05
        Entry 0: LE 1M
          Type: Active (0x01)
          Interval: 11.250 msec (0x0012)
          Window: 11.250 msec (0x0012)
        Entry 1: LE Coded
          Type: Active (0x01)
          Interval: 11.250 msec (0x0012)
          Window: 11.250 msec (0x0012)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6
        Extended scan: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
        Duration: 0 msec (0x0000)
        Period: 0.00 sec (0x0000)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Enable (0x08|0x0042) ncmd 2
        Status: Success (0x00)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This defines and implement phy changed event and send it to user
whenever selected PHYs changes using SET_PHY_CONFIGURATION.

This will be also trigerred when BREDR pkt_type is changed using
the legacy ioctl HCISETPTYPE.

@ MGMT Command: Set PHY Configuration (0x0045) plen 4
		Selected PHYs: 0x7fff
		  BR 1M 1SLOT
		  BR 1M 3SLOT
		  BR 1M 5SLOT
		  EDR 2M 1SLOT
		  EDR 2M 3SLOT
		  EDR 2M 5SLOT
		  EDR 3M 1SLOT
		  EDR 3M 3SLOT
		  EDR 3M 5SLOT
		  LE 1M TX
		  LE 1M RX
		  LE 2M TX
		  LE 2M RX
		  LE CODED TX
		  LE CODED RX
< HCI Command: LE Set Default PHY (0x08|0x0031) plen 3
		All PHYs preference: 0x00
		TX PHYs preference: 0x07
		  LE 1M
		  LE 2M
		  LE Coded
		RX PHYs preference: 0x07
		  LE 1M
		  LE 2M
		  LE Coded
> HCI Event: Command Complete (0x0e) plen 4
	  LE Set Default PHY (0x08|0x0031) ncmd 1
		Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 3
	  Set PHY Configuration (0x0045) plen 0
		Status: Success (0x00)
@ MGMT Event: PHY Configuration Changed (0x0026) plen 4
		Selected PHYs: 0x7fff
		  BR 1M 1SLOT
		  BR 1M 3SLOT
		  BR 1M 5SLOT
		  EDR 2M 1SLOT
		  EDR 2M 3SLOT
		  EDR 2M 5SLOT
		  EDR 3M 1SLOT
		  EDR 3M 3SLOT
		  EDR 3M 5SLOT
		  LE 1M TX
		  LE 1M RX
		  LE 2M TX
		  LE 2M RX
		  LE CODED TX
		  LE CODED RX
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This enables user to set phys which will be used in all subsequent
connections. Also host will use the same in LE scanning as well.

@ MGMT Command: Set PHY Configuration (0x0045) plen 4
        Selected PHYs: 0x7fff
          BR 1M 1SLOT
          BR 1M 3SLOT
          BR 1M 5SLOT
          EDR 2M 1SLOT
          EDR 2M 3SLOT
          EDR 2M 5SLOT
          EDR 3M 1SLOT
          EDR 3M 3SLOT
          EDR 3M 5SLOT
          LE 1M TX
          LE 1M RX
          LE 2M TX
          LE 2M RX
          LE CODED TX
          LE CODED RX
< HCI Command: LE Set Default PHY (0x08|0x0031) plen 3
        All PHYs preference: 0x00
        TX PHYs preference: 0x07
          LE 1M
          LE 2M
          LE Coded
        RX PHYs preference: 0x07
          LE 1M
          LE 2M
          LE Coded
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Default PHY (0x08|0x0031) ncmd 1
        Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 3
      Set PHY Configuration (0x0045) plen 0
        Status: Success (0x00)
@ MGMT Event: PHY Configuration Changed (0x0026) plen 4
        Selected PHYs: 0x7fff
          BR 1M 1SLOT
          BR 1M 3SLOT
          BR 1M 5SLOT
          EDR 2M 1SLOT
          EDR 2M 3SLOT
          EDR 2M 5SLOT
          EDR 3M 1SLOT
          EDR 3M 3SLOT
          EDR 3M 5SLOT
          LE 1M TX
          LE 1M RX
          LE 2M TX
          LE 2M RX
          LE CODED TX
          LE CODED RX
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This commands basically retrieve the supported packet types of
BREDR and supported PHYs of the controller.

BR_1M_1SLOT, LE_1M_TX and LE_1M_RX would be supported by default.
Other PHYs are supported based on the local features.

Also this sets PHY_CONFIGURATION bit in supported settings.

@ MGMT Command: Get PHY Configuration (0x0044) plen 0
@ MGMT Event: Command Complete (0x0001) plen 15
      Get PHY Configuration (0x0044) plen 12
        Status: Success (0x00)
        Supported PHYs: 0x7fff
          BR 1M 1SLOT
          BR 1M 3SLOT
          BR 1M 5SLOT
          EDR 2M 1SLOT
          EDR 2M 3SLOT
          EDR 2M 5SLOT
          EDR 3M 1SLOT
          EDR 3M 3SLOT
          EDR 3M 5SLOT
          LE 1M TX
          LE 1M RX
          LE 2M TX
          LE 2M RX
          LE CODED TX
          LE CODED RX
        Configurable PHYs: 0x79fe
          BR 1M 3SLOT
          BR 1M 5SLOT
          EDR 2M 1SLOT
          EDR 2M 3SLOT
          EDR 2M 5SLOT
          EDR 3M 1SLOT
          EDR 3M 3SLOT
          EDR 3M 5SLOT
          LE 2M TX
          LE 2M RX
          LE CODED TX
          LE CODED RX
        Selected PHYs: 0x07ff
          BR 1M 1SLOT
          BR 1M 3SLOT
          BR 1M 5SLOT
          EDR 2M 1SLOT
          EDR 2M 3SLOT
          EDR 2M 5SLOT
          EDR 3M 1SLOT
          EDR 3M 3SLOT
          EDR 3M 5SLOT
          LE 1M TX
          LE 1M RX
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This also add macros for checking LMP support for different
pkt_types
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

1M is mandatory to be supported by LE controllers and the same
would be set in power on. This patch defines hdev flags for
LE PHYs and set 1M to default.
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This implements extended LE craete connection and enhanced
LE conn complete event if the controller supports.

For now it is as good as legacy LE connection and event as
no new features in the extended connection is handled.

< HCI Command: LE Extended Create Connection (0x08|0x0043) plen 26
        Filter policy: White list is not used (0x00)
        Own address type: Public (0x00)
        Peer address type: Random (0x01)
        Peer address: DB:7E:2E:1D:85:E8 (Static)
        Initiating PHYs: 0x01
        Entry 0: LE 1M
          Scan interval: 60.000 msec (0x0060)
          Scan window: 60.000 msec (0x0060)
          Min connection interval: 50.00 msec (0x0028)
          Max connection interval: 70.00 msec (0x0038)
          Connection latency: 0 (0x0000)
          Supervision timeout: 420 msec (0x002a)
          Min connection length: 0.000 msec (0x0000)
          Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4
      LE Extended Create Connection (0x08|0x0043) ncmd 2
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 31
      LE Enhanced Connection Complete (0x0a)
        Status: Success (0x00)
        Handle: 3585
        Role: Master (0x00)
        Peer address type: Random (0x01)
        Peer address: DB:7E:2E:1D:85:E8 (Static)
        Local resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
        Peer resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
        Connection interval: 67.50 msec (0x0036)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Master clock accuracy: 0x00
@ MGMT Event: Device Connected (0x000b) plen 40
        LE Address: DB:7E:2E:1D:85:E8 (Static)
        Flags: 0x00000000
        Data length: 27
        Name (complete): Designer Mouse
        Appearance: Mouse (0x03c2)
        Flags: 0x05
          LE Limited Discoverable Mode
          BR/EDR Not Supported
        16-bit Service UUIDs (complete): 1 entry
          Human Interface Device (0x1812)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch enables Extended ADV report event if extended scanning
is supported in the controller and process the same.

The new features are not handled and for now its as good as
legacy ADV report.

> HCI Event: LE Meta Event (0x3e) plen 53
      LE Extended Advertising Report (0x0d)
        Num reports: 1
        Entry 0
          Event type: 0x0013
            Props: 0x0013
              Connectable
              Scannable
              Use legacy advertising PDUs
            Data status: Complete
          Legacy PDU Type: ADV_IND (0x0013)
          Address type: Random (0x01)
          Address: DB:7E:2E:1A:85:E8 (Static)
          Primary PHY: LE 1M
          Secondary PHY: LE 1M
          SID: 0x00
          TX power: 0 dBm
          RSSI: -90 dBm (0xa6)
          Periodic advertising invteral: 0.00 msec (0x0000)
          Direct address type: Public (0x00)
          Direct address: 00:00:00:00:00:00 (OUI 00-00-00)
          Data length: 0x1b
        0f 09 44 65 73 69 67 6e 65 72 20 4d 6f 75 73 65  ..Designer Mouse
        03 19 c2 03 02 01 05 03 03 12 18                 ...........
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This implements Set extended scan param and set extended scan enable
commands and use it for start LE scan based on controller support.

The new features added in these commands are setting of new PHY for
scanning and setting of scan duration. Both features are disabled
for now, meaning only 1M PHY is set and scan duration is set to 0
which means that scanning will be done untill scan disable is called.

< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement (0x00)
        PHYs: 0x01
        Entry 0: LE 1M
          Type: Active (0x01)
          Interval: 11.250 msec (0x0012)
          Window: 11.250 msec (0x0012)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6
        Extended scan: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
        Duration: 0 msec (0x0000)
        Period: 0.00 sec (0x0000)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Enable (0x08|0x0042) ncmd 2
        Status: Success (0x00)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Check for Resolv list supported by controller. So check the supported
commmand first before issuing this command i.e.,HCI_OP_LE_CLEAR_RESOLV_LIST

Before patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 13.338168
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 13.338842
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 13.339029
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 13.339939
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0  #59 [hci0] 13.340152
> HCI Event: Command Complete (0x0e) plen 5                #60 [hci0] 13.340952
      LE Read Resolving List Size (0x08|0x002a) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #61 [hci0] 13.341180
> HCI Event: Command Complete (0x0e) plen 12               #62 [hci0] 13.341898
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040

After patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 28.919131
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 28.920016
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 28.920164
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 28.920873
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0  #59 [hci0] 28.921109
> HCI Event: Command Complete (0x0e) plen 5                #60 [hci0] 28.922016
      LE Read Resolving List Size (0x08|0x002a) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear Resolving... (0x08|0x0029) plen 0  #61 [hci0] 28.922166
> HCI Event: Command Complete (0x0e) plen 4                #62 [hci0] 28.922872
      LE Clear Resolving List (0x08|0x0029) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #63 [hci0] 28.923117
> HCI Event: Command Complete (0x0e) plen 12               #64 [hci0] 28.924030
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040
Signed-off-by: NAnkit Navik <ankit.p.navik@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When the controller supports the Read LE Resolv List size feature, the
maximum list size are read and now stored.

Before patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 17.979791
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 17.980629
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 17.980786
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 17.981627
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #59 [hci0] 17.981786
> HCI Event: Command Complete (0x0e) plen 12               #60 [hci0] 17.982636
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040

After patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 13.338168
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 13.338842
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 13.339029
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 13.339939
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0  #59 [hci0] 13.340152
> HCI Event: Command Complete (0x0e) plen 5                #60 [hci0] 13.340952
      LE Read Resolving List Size (0x08|0x002a) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #61 [hci0] 13.341180
> HCI Event: Command Complete (0x0e) plen 12               #62 [hci0] 13.341898
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040
Signed-off-by: NAnkit Navik <ankit.p.navik@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Essentially the same as the ipv4 equivalents.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

enable_sriov - Enables Single-Root Input/Output Virtualization(SR-IOV)
characteristic of the device.
Reviewed-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add 2 first generic parameters to devlink configuration parameters set:
internal_err_reset - When set enables reset device on internal errors.
max_macs - max number of MACs per ETH port.
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add devlink_param_notify() function to support devlink param notifications.
Add notification call to devlink param set, register and unregister
functions.
Add devlink_param_value_changed() function to enable the driver notify
devlink on value change. Driver should use this function after value was
changed on any configuration mode part to driverinit.
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"driverinit" configuration mode value is held by devlink to enable
the driver query the value after reload. Two additional functions
added to help the driver get/set the value from/to devlink:
devlink_param_driverinit_value_set() and
devlink_param_driverinit_value_get().
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add param set command to set value for a parameter.
Value can be set to any of the supported configuration modes.
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define configuration parameters data structure.
Add functions to register and unregister the driver supported
configuration parameters table.
For each parameter registered, the driver should fill all the parameter's
fields. In case the only supported configuration mode is "driverinit"
the parameter's get()/set() functions are not required and should be set
to NULL, for any other configuration mode, these functions are required
and should be set by the driver.
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the socket error queue for reporting dropped packets if the
socket has enabled that feature through the SO_TXTIME API.

Packets are dropped either on enqueue() if they aren't accepted by the
qdisc or on dequeue() if the system misses their deadline. Those are
reported as different errors so applications can react accordingly.

Userspace can retrieve the errors through the socket error queue and the
corresponding cmsg interfaces. A struct sock_extended_err* is used for
returning the error data, and the packet's timestamp can be retrieved by
adding both ee_data and ee_info fields as e.g.:

    ((__u64) serr->ee_data << 32) + serr->ee_info

This feature is disabled by default and must be explicitly enabled by
applications. Enabling it can bring some overhead for the Tx cycles
of the application.
Signed-off-by: NJesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add infra so etf qdisc supports HW offload of time-based transmission.

For hw offload, the time sorted list is still used, so packets are
dequeued always in order of txtime.

Example:

$ tc qdisc replace dev enp2s0 parent root handle 100 mqprio num_tc 3 \
           map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 0

$ tc qdisc add dev enp2s0 parent 100:1 etf offload delta 100000 \
	   clockid CLOCK_REALTIME

In this example, the Qdisc will use HW offload for the control of the
transmission time through the network adapter. The hrtimer used for
packets scheduling inside the qdisc will use the clockid CLOCK_REALTIME
as reference and packets leave the Qdisc "delta" (100000) nanoseconds
before their transmission time. Because this will be using HW offload and
since dynamic clocks are not supported by the hrtimer, the system clock
and the PHC clock must be synchronized for this mode to behave as
expected.
Signed-off-by: NJesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds 'qdisc_watchdog_init_clockid()' that allows a clockid to be
passed, this allows other time references to be used when scheduling
the Qdisc to run.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a transmit_time field to struct inet_cork, then copy the
timestamp from the CMSG cookie at ip_setup_cork() so we can
safely copy it into the skb later during __ip_make_skb().

For the raw fast path, just perform the copy at raw_send_hdrinc().
Signed-off-by: NRichard Cochran <rcochran@linutronix.de>
Signed-off-by: NJesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces SO_TXTIME. User space enables this option in
order to pass a desired future transmit time in a CMSG when calling
sendmsg(2). The argument to this socket option is a 8-bytes long struct
provided by the uapi header net_tstamp.h defined as:

struct sock_txtime {
	clockid_t 	clockid;
	u32		flags;
};

Note that new fields were added to struct sock by filling a 2-bytes
hole found in the struct. For that reason, neither the struct size or
number of cachelines were altered.
Signed-off-by: NRichard Cochran <rcochran@linutronix.de>
Signed-off-by: NJesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also involved adding a way to run a netfilter hook over a list of packets.
 Rather than attempting to make netfilter know about lists (which would be
 a major project in itself) we just let it call the regular okfn (in this
 case ip_rcv_finish()) for any packets it steals, and have it give us back
 a list of packets it's synchronously accepted (which normally NF_HOOK
 would automatically call okfn() on, but we want to be able to potentially
 pass the list to a listified version of okfn().)
The netfilter hooks themselves are indirect calls that still happen per-
 packet (see nf_hook_entry_hookfn()), but again, changing that can be left
 for future work.

There is potential for out-of-order receives if the netfilter hook ends up
 synchronously stealing packets, as they will be processed before any
 accepts earlier in the list.  However, it was already possible for an
 asynchronous accept to cause out-of-order receives, so presumably this is
 considered OK.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Like some other per transport params, flowlabel and dscp are added
in transport, asoc and sctp_sock. By default, transport sets its
value from asoc's, and asoc does it from sctp_sock. flowlabel
only works for ipv6 transport.

Other than that they need to be passed down in sctp_xmit, flow4/6
also needs to set them before looking up route in get_dst.

Note that it uses '& 0x100000' to check if flowlabel is set and
'& 0x1' (tos 1st bit is unused) to check if dscp is set by users,
so that they could be set to 0 by sockopt in next patch.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces __ip_queue_xmit(), through which the callers
can pass tos param into it without having to set inet->tos. For
ipv6, ip6_xmit() already allows passing tclass parameter.

It's needed when some transport protocol doesn't use inet->tos,
like sctp's per transport dscp, which will be added in next patch.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support to pick Tx queue based on the Rx queue(s) map
configuration set by the admin through the sysfs attribute
for each Tx queue. If the user configuration for receive queue(s) map
does not apply, then the Tx queue selection falls back to CPU(s) map
based selection and finally to hashing.
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new field to sock_common 'skc_rx_queue_mapping'
which holds the receive queue number for the connection. The Rx queue
is marked in tcp_finish_connect() to allow a client app to do
SO_INCOMING_NAPI_ID after a connect() call to get the right queue
association for a socket. Rx queue is also marked in tcp_conn_request()
to allow syn-ack to go on the right tx-queue associated with
the queue on which syn is received.
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change 'skc_tx_queue_mapping' field in sock_common structure from
'int' to 'unsigned short' type with ~0 indicating unset and
other positive queue values being set. This will accommodate adding
a new 'unsigned short' field in sock_common in the next patch for
rx_queue_mapping.
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SMC-D relies on PNETIDs to find usable SMC-D/ISM devices for a SMC
connection. This patch adds SMC-D/ISM support to the current PNETID
implementation.
Signed-off-by: NHans Wippel <hwippel@linux.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Suggested-by: NThomas Richter <tmricht@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SMC supports two variants: SMC-R and SMC-D. For data transport, SMC-R
uses RDMA devices, SMC-D uses so-called Internal Shared Memory (ISM)
devices. An ISM device only allows shared memory communication between
SMC instances on the same machine. For example, this allows virtual
machines on the same host to communicate via SMC without RDMA devices.

This patch adds the base infrastructure for SMC-D and ISM devices to
the existing SMC code. It contains the following:

* ISM driver interface:
  This interface allows an ISM driver to register ISM devices in SMC. In
  the process, the driver provides a set of device ops for each device.
  SMC uses these ops to execute SMC specific operations on or transfer
  data over the device.

* Core SMC-D link group, connection, and buffer support:
  Link groups, SMC connections and SMC buffers (in smc_core) are
  extended to support SMC-D.

* SMC type checks:
  Some type checks are added to prevent using SMC-R specific code for
  SMC-D and vice versa.

To actually use SMC-D, additional changes to pnetid, CLC, CDC, etc. are
required. These are added in follow-up patches.
Signed-off-by: NHans Wippel <hwippel@linux.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Suggested-by: NThomas Richter <tmricht@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

s390 hardware supports the definition of a so-call Physical NETwork
IDentifier (short PNETID) per network device port. These PNETIDS
can be used to identify network devices that are attached to the same
physical network (broadcast domain).

On s390 try to use the PNETID of the ethernet device port used for
initial connecting, and derive the IB device port used for SMC RDMA
traffic.

On platforms without PNETID support fall back to the existing
solution of a configured pnet table.
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check the tunnel option type stored in tunnel flags when creating options
for tunnels. Thereby ensuring we do not set geneve, vxlan or erspan tunnel
options on interfaces that are not associated with them.

Make sure all users of the infrastructure set correct flags, for the BPF
helper we have to set all bits to keep backward compatibility.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This feature is actually already supported by sk->sk_reuse which can be
set by socket level opt SO_REUSEADDR. But it's not working exactly as
RFC6458 demands in section 8.1.27, like:

  - This option only supports one-to-one style SCTP sockets
  - This socket option must not be used after calling bind()
    or sctp_bindx().

Besides, SCTP_REUSE_PORT sockopt should be provided for user's programs.
Otherwise, the programs with SCTP_REUSE_PORT from other systems will not
work in linux.

To separate it from the socket level version, this patch adds 'reuse' in
sctp_sock and it works pretty much as sk->sk_reuse, but with some extra
setup limitations that are needed when it is being enabled.

"It should be noted that the behavior of the socket-level socket option
to reuse ports and/or addresses for SCTP sockets is unspecified", so it
leaves SO_REUSEADDR as is for the compatibility.

Note that the name SCTP_REUSE_PORT is somewhat confusing, as its
functionality is nearly identical to SO_REUSEADDR, but with some
extra restrictions. Here it uses 'reuse' in sctp_sock instead of
'reuseport'. As for sk->sk_reuseport support for SCTP, it will be
added in another patch.

Thanks to Neil to make this clear.

v1->v2:
  - add sctp_sk->reuse to separate it from the socket level version.
v2->v3:
  - improve changelog according to Marcelo's suggestion.
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The poll() changes were not well thought out, and completely
unexplained.  They also caused a huge performance regression, because
"->poll()" was no longer a trivial file operation that just called down
to the underlying file operations, but instead did at least two indirect
calls.

Indirect calls are sadly slow now with the Spectre mitigation, but the
performance problem could at least be largely mitigated by changing the
"->get_poll_head()" operation to just have a per-file-descriptor pointer
to the poll head instead.  That gets rid of one of the new indirections.

But that doesn't fix the new complexity that is completely unwarranted
for the regular case.  The (undocumented) reason for the poll() changes
was some alleged AIO poll race fixing, but we don't make the common case
slower and more complex for some uncommon special case, so this all
really needs way more explanations and most likely a fundamental
redesign.

[ This revert is a revert of about 30 different commits, not reverted
  individually because that would just be unnecessarily messy  - Linus ]

Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Netfilter assumes that if the socket is present in the skb, then
it can be used because that reference is cleaned up while the skb
is crossing netns.

We want to change that to preserve the socket reference in a future
patch, so this is a preparation updating netfilter to check if the
socket netns matches before use it.
Signed-off-by: NFlavio Leitner <fbl@redhat.com>
Acked-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix coding style issues in tc pedit headers detected by the
checkpatch script.
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NRoman Mashak <mrv@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>