Allow reading and setting bcast filtering configuration
through debugfs.

By default, mvm->bcast_filters is used for setting
the bcast filtering configuration (these filters
will be configured for each associated station).

For testing purposes, allow overriding this configuration,
and setting the bcast filtering configuration manually.
The following debugfs keys can be used:
* bcast_filtering/override - use debugfs values instead
	of default configuration
* bcast_filtering/filters - set filters (+ attributes)
* bcast_filtering/macs - per-mac bcast filtering
	configuration (policy + attached filters)
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add our ip as a new attribute to the bcast filtering
configuration (i.e. check the dest ip field of the
arp request).

Add bcast filter to pass incoming dhcp offer
broadcast frames as well (for sta vifs).

In order to support such dynamic configuration,
use the reserved1 field as a bitmap for driver internal
flags (which will indicate we want to configure the ip
in this attribute), and reconfigure the bcast
filtering on BSS_CHANGED_ARP_FILTER indication.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Configure arp request broadcast filter if this
option is enabled, in order to allow only arp
request broadcasts to pass-in.

(A following patch will make this filter even narrower
by limiting the arp request to our own ip)
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Broadcast filtering allows dropping broadcast
frames that don't match the configured patterns.

Use predefined filters, and configure them for
each associated station vif.

There is no need to optimize and attach the same
filter to multiple vifs, as a following patch
will configure each filter to have per-vif unique
values.

Configure the bcast filtering on assoc changes.

Add a new IWLWIFI_BCAST_FILTERING Kconfig option
in order to enable broadcast filtering.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

As a debug tool, we dump the SRAM from the device when an
error occurs. The main users of this want it in a different
format, so change the format to suit their needs.
Also - add a short delay between the prints to make sure
that the user space logger can catch up.

This happens only when the firmware asserts, and only when
fw_restart is set to 0 which is typically a testing
configuration.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Based on the Bluetooth activity grading, we can stop using
the shared antenna and ask the stations to honor the new
SMPS state.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If a vif is in low latency mode, it should be in primary
channel.
Also tell BT Coex about the change when a vif enters or
exits low latency mode.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Limit the scheduling duration of bindings without a low-latency
interface in the firmware, this prevents those bindings from
occupying the medium for a period of time longer than what we
want for the other interfaces in low-latency mode.

As older firmware doesn't do anything with the max_duration field
and ignores it completely, there's no need for a firmware flag.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If there is/are interface(s) in low-latency mode, reserve a
percentage (currently 64%) of the quota for that binding to
improve the quality of service for those interfaces. However,
if there's more than one binding that has low-latency, then
give up and don't reserve, we can't allocate more than 100%.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

While an interface is in low-latency mode, for now powersave
should be disabled for it, so take low-latency into account
in the powersave code and force powersave recalculation when
low-latency mode changes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

For various traffic use cases, we want to be able to treat multi-
channel scenarios differently. Introduce a low-latency framework
that currently only has a debugfs file to enable low-latency mode,
but can later be extended.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Notify scan completed if fw_restart flow isn't going to be run.
Otherwise, the scan will stay stack forever and mac80211 will
not be able to remove the interface.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Don't stop scheduled scan before reporting HW restart;
mac80211 was changed to reschedule it after reconfigure.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In iwl_pcie_int_cause_non_ict, trans_pcie is used for lockdep
purposes only. Since this might not be enabled, trans_pcie
finds itself without user leading to a complaint from gcc.
Avoid using trans_pcie by inlining IWL_TRANS_GET_PCIE_TRANS.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Since we use IWL_MVM_STATION_COUNT all over the driver, we
need to make sure that it is the right constant to look at.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We somtimes need to fetch the iwl_mvm_sta structure from a
station index - provide a helper to do that.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The calib_version is 255 and this is perfectly fine - no
need to leave a TODO there.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

iwlwifi-7260-8.ucode has been release. Warn if it is not
on the file system.
iwlwifi-7260-7.ucode is still supported for another kernel
version.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The code seems fine, as buf won't be assigned when an error
is returned, but checking for the error first is easier to
understand.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Also handle the bypass mode in which the second CPU doesn't
interfere.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This configuration is invalid for this family.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NDor Shaish <dor.shaish@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This register is not present in 8000 family devices.
There is prph register instead.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NDor Shaish <dor.shaish@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

APMG HW block was removed in this NIC, hence, no need to
configure it.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The identification of the hardware section in the NVM
of new devices has been changed, hence the need to add it
to iwl_cfg and adapt the code that uses this value
accordingly.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

add 8000-family configuration to iwl_cfg struct.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NDor Shaish <dor.shaish@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Newer firmware will support uAPSD clients in AP/GO mode, so complete
the driver support for it. The way it works is described in comments
in the code, but basically the driver just has to pass down all the
mac80211 requests and do accounting on agg/non-agg queues properly.

For older firmware, this doesn't change anything as it ignores the
fields used by the new firmware, and we only advertise uAPSD support
when the firmware does.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

None of the devices supported by iwldvm have support for
shadow registers. This means that we wake the NIC
when we increment the write pointer on Tx ring.
This happened even before my bad commit mentionned below.
Since my commit below, we wake up the NIC when we put a
host command on the ring regardless of shadow register
support. This means that in iwldvm (when the NIC doesn't
support shadow register), we wake up the NIC twice:

pcie_enqueue_hcmd:
	wake up the NIC
	iwl_pcie_txq_inc_wr_ptr:
		wake up the NIC - no shadow reg support

Since waking up the NIC means that we need to acquire a
spinlock, this obviously leads to a recursive spinlock
and hence a freeze.

Fixes: b9439491 ("iwlwifi: pcie: keep the NIC awake when commands are in flight")
Reported-by: NJanusz Dziedzic <janusz.dziedzic@gmail.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Keeping this as 0 is ok according to spec section 9.7.11
as this means the limits are according to the Tx/Rx
supported MCS x NSS bitmap. Initially we've set these as
there were concerns of interop issues but these turned out
to be false.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If we try to write NVM that do not exist, the function will return
uninitialized value. fixed.
Signed-off-by: NEytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add an inline helper function for getting an RX packet's
length or payload length and use it throughout the code
(most of which I did using an spatch.)

While at it, adjust some code, and remove a bogus comment
from the dvm calibration code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All beamformee supporting chips have the ability to support
VHT NDP in up to 4 STSs. So change the published beamformee
STS cap accordingly to 3 as it should be Nsts-1.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The request of SMPS issued by the Thermal Throttling code
was not reset when we disassociated - fix that.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

It's a bit strange to treat an array as a pointer, so use proper
array indexing instead.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If the length isn't set it means we want all the SRAM.
Also - this is perfectly valid to partially dump starting
at offset 0.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Discovered by klocwork

Array 'iwl_rate_mcs' of size 15 may use index value(s) -1
  * rs.c:2562: index = iwl_hwrate_to_plcp_idx(rate)
    * rs.c:2562: Result of function call 'iwl_hwrate_to_plcp_idx(rate)' is '[-1,14]'
  * rs.c:2565: Array 'iwl_rate_mcs' size is 15.
  * rs.c:2565: Possible attempt to access element -1 of array 'iwl_rate_mcs'.

While at it stop using index = -1 and always use IWL_RATE_INVALID
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Some NIC comes with more than the 4 NVM (non volative
memory) sections described in the nvm_to_read array.
These NICs usually get their NVM from an external file
fetched from userland during init.
We already parsed the file, but sent to the NIC only 4 NVM
sections whereas there could be more sections in the file.
Fix this.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Since seq_number is incremented right after using
it, so printed seq_ctrl was actually the next
one to be used.

Fix it by incrementing the seq_number only later,
before saving it.

Additionally, use the IEEE80211_SEQ_TO_SN macro
in order to print the actual sequence number.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Enabling the oscillator consumes slightly more power (100uA)
but allows to make sure that we exit from L1 on time.

Not doing so might lead to a PCIe specification violation
since we might wake up from L1 at the wrong time.
This issue has been identified on 3160 and 7260 only.
On older NICs L1 off is not enabled, on newer NICs (7265),
the issue is fixed.

When the bug occurs the user sees that the NIC has
disappeared from the PCI bridge, any access to the device
returns 0xff.

This fixes:
	https://bugzilla.kernel.org/show_bug.cgi?id=64541

and has been extensively discussed here:
	http://markmail.org/thread/mfmpzqt3r333n4bo

Cc: stable@vger.kernel.org [3.10+]
Fixes: 99cd4714 ("iwlwifi: add 7000 series device configuration")
Reported-and-tested-by: Nwzyboy <wzyboy@wzyboy.org>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>