- 30 6月, 2011 4 次提交
-
-
由 Krishna Gudipati 提交于
Made changes to FCS lport, vport state machines to support vport enable / disable operations. Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Krishna Gudipati 提交于
- Added support for Brocade-1860 Fabric Adapter. - Made changes to support single firmware image per asic type. - Combined bfi_cbreg.h and bfi_ctreg.h defines into bfi_reg.h with only minimal defines used by host. - Added changes to setup CPE/RME Queue register offsets based on firmware response. - Removed queue register offset initializations and added register offsets to BFI config response message. - Added Brocade-1860 asic specific interrupt status definitions and mailbox interfaces. Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Krishna Gudipati 提交于
- Add PBC port Disabled condition check. - Rename incorrectly named LPS I2H messages. Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
由 Krishna Gudipati 提交于
- Avoid the use of hardware defined structure bfi_sge_s for DMA requests in host. - Defined a generic address len pair to represent a DMA memory chunk (bfi_alen_s). Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com> Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
-
- 22 12月, 2010 4 次提交
-
-
由 Krishna Gudipati 提交于
- Direct attach is not working due to the check of PID in fcxp_send request. - Added logic to set the lps->lp_pid with the PID assigned for n2n mode. Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 Krishna Gudipati 提交于
When the bfa driver is loaded a flogi is sent without the knowledge of trunking configuration. This normal flogi causes the switch ports which had trunking enabled to go to persistent offline. Solution is to store the port configuration (which has trunking info) in the flash for persistency. The firmware will read this configuration when the very first fcport enable is received. Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 Maggie Zhang 提交于
Remove SCSI IO callbacks, and as a result remove bfa_cb_ioim.h. Signed-off-by: NMaggie Zhang <xmzhang@brocade.com> Signed-off-by: NJing Huang <huangj@brocade.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
由 Maggie 提交于
First round of fix for the endianess check warnings from make C=2 CF="-D__CHECK_ENDIAN__". Signed-off-by: NMaggie <xmzhang@brocade.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
- 26 10月, 2010 1 次提交
-
-
由 Jing Huang 提交于
This patch addresses the comments from Randy Dunlap (Randy.Dunlap@oracle.com) regarding comment blocks that begining with "/**". bfa driver comments currently do not follow kernel-doc convention, we hence replace all /** with /* and **/ with */. Signed-off-by: NJing Huang <huangj@brocade.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-
- 17 9月, 2010 1 次提交
-
-
由 Krishna Gudipati 提交于
We have flattened the BFA hierarchy and also reduced the number of source and header files we used to have earlier. Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com> Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
-