HW workaround:
Disable logging of correctable error for some NX3031 based adapter.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is race between netif_stop_queue and netif_stopped_queue
check.So check once again if buffers are available to avoid race.
With above logic we can also get rid of tx lock in process_cmd_ring.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added statistics for Nic Partition supported adapter.
These statistics are maintined in device.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change a few checks against the hardcoded broadcast address,
0xffffffff, to ipv4_is_lbcast().  Remove some existing checks
using ipv4_is_lbcast() that are now obviously superfluous.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As suggested by: Joe Perches <joe@perches.com>

Although RSS is meaningless when there is a single HW queue we
still need it enabled in order to have HW Rx hash generated.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the value of the constant is the same, but it's clearer to use original
constant provided by HSI
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Optimized the branching in the bnx2x_rx_int() based on the fact
that FP CQE will always have at least one of START or STOP flags set,
so if not both bits are set and START bit is not set,
then it's a STOP bit that is set.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>

Since commit e446630c, i.e. v2.6.35-rc1,
the mcp251x chip model can be selected via the modalias member in the
struct spi_board_info. The driver stores the actual model in the
struct mcp251x_platform_data.

From the driver point of view the platform_data should be read only.
Since all in-tree users of the mcp251x have already been converted to
the modalias method, this patch moves the "model" member from the
struct mcp251x_platform_data to the driver's private data structure.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Cc: Christian Pellegrin <chripell@fsfe.org>
Cc: Marc Zyngier <maz@misterjones.org>

This patch introduces a variable "clear_intf" that hold the bits that
should be cleared. Only read-modify-write register if "clear_intf"
is set.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>

Use read-modify-write instead of a simple write to change the register
contents, to close existing the race window between the original manual
read and write.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>

This patch bases on work done earlier by David Jander.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NDavid Jander <david@protonic.nl>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>

This patch replaces netif_rx() with netif_rx_ni() which has to be used
from the threaded interrupt i.e. process context context.

Thanks to Christian Pellegrin for pointing at the right fix:
481a8199 by Oliver Hartkopp.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>

This is essentially cosmetic.  At this point the IRQs are already
disabled because we called spin_lock_irq(&dev->rx_info.lock).

The real bug here was fixed back in 2006 in 3a10cceb: "[PATCH] lock
validator: fix ns83820.c irq-flags bug".  Prior to that patch, it was
a "spin_lock_irq is not nestable" type bug.  The 2006 patch changes the
unlock to not re-enable IRQs, which eliminates the potential deadlock.

But this bit was missed.  We should change the lock function as well so
it balances nicely.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Optimize processing in TIPC's bearer shutdown code, including:

1. Remove an unnecessary check to see if TIPC bearer's can exist.
2. Don't release spinlocks before calling a media-specific disabling
routine, since the routine can't sleep.
3. Make bearer_disable() operate directly on a struct bearer, instead
of needlessly taking a name and then mapping that to the struct.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's completely unused and exporting a static symbol
makes no sense and breaks the build.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the tg3 version to 3.115.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the tg3 driver leaves the speed and duplex fields
uninitialized in tg3_get_settings() if the device is not up.  This can
lead to some strange deductions in certain versions of ethtool.  When
the device is up and the link is down, the driver reports SPEED_INVALID
and DUPLEX_INVALID for these fields.  This patch makes the presentation
consistent by returning SPEED_INVALID and DUPLEX_INVALID when the device
has not been brought up as well.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5714, 5715, and 5780 devices do not have a separate rx jumbo
producer ring.  This patch changes the code so that resources are not
allocated for it.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

src_map is no longer used in tg3_alloc_rx_skb().  Remove it.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds Energy Efficient Ethernet (EEE) support for the 5718
device ID and the 57765 B0 asic revision.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds clause 45 register access methods.  They will be used in
the following patch.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows the driver to disable the additional transmit rings
available on the 5717 and 5719 devices.  This is not strictly necessary,
but is done anyways for correctness.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

5718 B0 and 5719 devices will use a new selfboot firmware format.  This
patch adds code to detect the new format so that bootcode versions get
reported correctly.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get rid of fib_hash_lock rwlock.

The fn_zone hash table resize is the noticeable part of this patch.

I added a seqlock per fn_zone, so that readers can restart their lookup
in the (very rare) case a writer expanded the hash table.

Add rcu heads in fib_alias and fib_node, use call_rcu() to defer their
freeing, and use appropriate _rcu list manipulations.

Stress test (160.000.000 udp frames sent, IP route cache disabled to
mimic DDOS attack, FIB_HASH)

Before:
real	0m41.191s
user	0m13.137s
sys	8m55.241s

After:
real	0m38.091s
user	0m13.189s
sys	7m53.018s
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

First step for RCU conversion of fib_hash :

struct fn_zone are created and never deleted.

Very classic conversion, using rcu_assign_pointer(), rcu_dereference()
and rtnl_dereference() verbs.

__rcu markers on fz_next and fn_zone_list

They are created under RTNL, we dont need fib_hash_lock anymore in
fn_new_zone().
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While looking for false sharing problems, I noticed
sizeof(struct fn_zone) was small (28 bytes) and possibly sharing a cache
line with an often written kernel structure.

Most of the time, fn_zone uses its initial hash table of 16 slots.

We can avoid the false sharing problem by embedding this initial hash
table in fn_zone itself, so that sizeof(fn_zone) > L1_CACHE_BYTES

We did a similar optimization in commit a6501e08 (Reduce memory needs
and speedup lookups)

Add a fz_revorder field to speedup fn_hash() a bit.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the standard macro to put this table in __devinitconst.

Compiled, untested.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a network bench, I noticed an unfortunate false sharing between
'loopback_dev' and 'count' fields in "struct net".

'count' is written each time a socket is created or destroyed, while
loopback_dev might be often read in routing code.

Move loopback_dev in a read mostly section of "struct net"

Note: struct netns_xfrm is cache line aligned on SMP.
(It contains a "struct dst_ops")
Move it at the end to avoid holes, and reduce sizeof(struct net) by 128
bytes on ia32.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As CWR is stronger than CA_Disorder state, we can miscount
SACK/Reno failure into other timeouts. Not a bad problem as
it can happen only due to ECN, FRTO detecting spurious RTO
or xmit error which are the only callers of tcp_enter_cwr.
And even then losses and RTO must still follow thereafter
to actually end up into the relevant code paths.

Compile tested.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When only fast rexmit should be done, tcp_mark_head_lost marks
L too far. Also, sacked_upto below 1 is perfectly valid number,
the packets == 0 then needs to be trapped elsewhere.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Reported-by: NArmando Visconti <armando.visconti@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Suppress a large block of warnings like:
drivers/net/niu.c:7094:38: warning: incorrect type in assignment (different base types)
drivers/net/niu.c:7094:38:    expected restricted __be32 [usertype] ip4src
drivers/net/niu.c:7094:38:    got unsigned long long
drivers/net/niu.c:7104:17: warning: cast from restricted __be32
...
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have USB, PCMCIA, and gigabit ethernet drivers that select
MII even though NET_ETHERNET is not enabled, so make MII not
be dependent on NET_ETHERNET.  It is still dependent on NET
and NETDEVICES.

Fixes kconfig unmet dependency warning (shortened, was very long string):

warning: (ARM_AT91_ETHER && NETDEVICES && NET_ETHERNET && ARM && ARCH_AT91RM9200 || ARM_KS8695_ETHER && NETDEVICES && NET_ETHERNET && ARM && ARCH_KS8695 || ... || IP1000 && NETDEVICES && NETDEV_1000 && PCI && EXPERIMENTAL || HAMACHI && NETDEVICES && NETDEV_1000 && PCI || R8169 && NETDEVICES && NETDEV_1000 && PCI || SIS190 && NETDEVICES && NETDEV_1000 && PCI || VIA_VELOCITY && NETDEVICES && NETDEV_1000 && PCI || ATL1 && NETDEVICES && NETDEV_1000 && PCI || ATL1E && NETDEVICES && NETDEV_1000 && PCI && EXPERIMENTAL || ATL1C && NETDEVICES && NETDEV_1000 && PCI && EXPERIMENTAL || JME && NETDEVICES && NETDEV_1000 && PCI || STMMAC_ETH && NETDEV_1000 && NETDEVICES && HAS_IOMEM || USB_PEGASUS && NETDEVICES && USB && NET || USB_RTL8150 && NETDEVICES && USB && NET && EXPERIMENTAL || USB_USBNET && NETDEVICES && USB && NET || PCMCIA_SMC91C92 && NETDEVICES && NET_PCMCIA && PCMCIA) selects MII which has unmet direct dependencies (NETDEVICES && NET_ETHERNET)
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com> [2006-NOV-30]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>