This patch implements 64 bit counter support for IBS. The
sampling period is no longer limited to the hw counter width.

The functions perf_event_set_period() and
perf_event_try_update() can be used as generic functions. They
can replace similar code that is duplicate across architectures.
Signed-off-by: NRobert Richter <robert.richter@amd.com>
Acked-by: NPeter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1323968199-9326-5-git-send-email-robert.richter@amd.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Add code to control the IBS pmu. We need to maintain per-cpu
states. Since some states are used and changed by the nmi
handler, access to these states must be atomic.
Signed-off-by: NRobert Richter <robert.richter@amd.com>
Acked-by: NPeter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1323968199-9326-4-git-send-email-robert.richter@amd.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

This patch implements code to handle ibs interrupts. If ibs data
is available a raw perf_event data sample is created and sent
back to the userland. This patch only implements the storage of
ibs data in the raw sample, but this could be extended in a
later patch by generating generic event data such as the rip
from the ibs sampling data.
Signed-off-by: NRobert Richter <robert.richter@amd.com>
Acked-by: NPeter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1323968199-9326-3-git-send-email-robert.richter@amd.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

This patch implements perf configuration for AMD IBS. The IBS
pmu is selected using the type attribute in sysfs. There are two
types of ibs pmus, for instruction fetch (IBS_FETCH) and for
instruction execution (IBS_OP):

 /sys/bus/event_source/devices/ibs_fetch/type
 /sys/bus/event_source/devices/ibs_op/type

Except for the sample period IBS can only be set up with raw
config values and raw data samples. The event attributes for the
syscall should be programmed like this (IBS_FETCH):

        type = get_pmu_type("/sys/bus/event_source/devices/ibs_fetch/type");

        memset(&attr, 0, sizeof(attr));
        attr.type        = type;
        attr.sample_type = PERF_SAMPLE_CPU | PERF_SAMPLE_RAW;
        attr.config      = IBS_FETCH_CONFIG_DEFAULT;

This implementation does not yet support 64 bit counters. It is
limited to the hardware counter bit width which is 20 bits. 64
bit support can be added later.
Signed-off-by: NRobert Richter <robert.richter@amd.com>
Acked-by: NPeter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1323968199-9326-2-git-send-email-robert.richter@amd.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Split out optprobe related code to arch/x86/kernel/kprobes-opt.c
for maintenanceability.
Signed-off-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Suggested-by: NIngo Molnar <mingo@elte.hu>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: systemtap@sourceware.org
Cc: anderson@redhat.com
Link: http://lkml.kernel.org/r/20120305133222.5982.54794.stgit@localhost.localdomain
[ Tidied up the code a tiny bit ]
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Fix a bug in kprobes which can modify kernel code
permanently at run-time. In the result, kernel can
crash when it executes the modified code.

This bug can happen when we put two probes enough near
and the first probe is optimized. When the second probe
is set up, it copies a byte which is already modified
by the first probe, and executes it when the probe is hit.
Even worse, the first probe and the second probe are removed
respectively, the second probe writes back the copied
(modified) instruction.

To fix this bug, kprobes always recovers the original
code and copies the first byte from recovered instruction.
Signed-off-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: systemtap@sourceware.org
Cc: anderson@redhat.com
Link: http://lkml.kernel.org/r/20120305133215.5982.31991.stgit@localhost.localdomainSigned-off-by: NIngo Molnar <mingo@elte.hu>

Current probed-instruction recovery expects that only breakpoint
instruction modifies instruction. However, since kprobes jump
optimization can replace original instructions with a jump,
that expectation is not enough. And it may cause instruction
decoding failure on the function where an optimized probe
already exists.

This bug can reproduce easily as below:

1) find a target function address (any kprobe-able function is OK)

 $ grep __secure_computing /proc/kallsyms
   ffffffff810c19d0 T __secure_computing

2) decode the function
   $ objdump -d vmlinux --start-address=0xffffffff810c19d0 --stop-address=0xffffffff810c19eb

  vmlinux:     file format elf64-x86-64

Disassembly of section .text:

ffffffff810c19d0 <__secure_computing>:
ffffffff810c19d0:       55                      push   %rbp
ffffffff810c19d1:       48 89 e5                mov    %rsp,%rbp
ffffffff810c19d4:       e8 67 8f 72 00          callq
ffffffff817ea940 <mcount>
ffffffff810c19d9:       65 48 8b 04 25 40 b8    mov    %gs:0xb840,%rax
ffffffff810c19e0:       00 00
ffffffff810c19e2:       83 b8 88 05 00 00 01    cmpl $0x1,0x588(%rax)
ffffffff810c19e9:       74 05                   je     ffffffff810c19f0 <__secure_computing+0x20>

3) put a kprobe-event at an optimize-able place, where no
 call/jump places within the 5 bytes.
 $ su -
 # cd /sys/kernel/debug/tracing
 # echo p __secure_computing+0x9 > kprobe_events

4) enable it and check it is optimized.
 # echo 1 > events/kprobes/p___secure_computing_9/enable
 # cat ../kprobes/list
 ffffffff810c19d9  k  __secure_computing+0x9    [OPTIMIZED]

5) put another kprobe on an instruction after previous probe in
  the same function.
 # echo p __secure_computing+0x12 >> kprobe_events
 bash: echo: write error: Invalid argument
 # dmesg | tail -n 1
 [ 1666.500016] Probing address(0xffffffff810c19e2) is not an instruction boundary.

6) however, if the kprobes optimization is disabled, it works.
 # echo 0 > /proc/sys/debug/kprobes-optimization
 # cat ../kprobes/list
 ffffffff810c19d9  k  __secure_computing+0x9
 # echo p __secure_computing+0x12 >> kprobe_events
 (no error)

This is because kprobes doesn't recover the instruction
which is overwritten with a relative jump by another kprobe
when finding instruction boundary.
It only recovers the breakpoint instruction.

This patch fixes kprobes to recover such instructions.

With this fix:

 # echo p __secure_computing+0x9 > kprobe_events
 # echo 1 > events/kprobes/p___secure_computing_9/enable
 # cat ../kprobes/list
 ffffffff810c1aa9  k  __secure_computing+0x9    [OPTIMIZED]
 # echo p __secure_computing+0x12 >> kprobe_events
 # cat ../kprobes/list
 ffffffff810c1aa9  k  __secure_computing+0x9    [OPTIMIZED]
 ffffffff810c1ab2  k  __secure_computing+0x12    [DISABLED]

Changes in v4:
 - Fix a bug to ensure optimized probe is really optimized
   by jump.
 - Remove kprobe_optready() dependency.
 - Cleanup code for preparing optprobe separation.

Changes in v3:
 - Fix a build error when CONFIG_OPTPROBE=n. (Thanks, Ingo!)
   To fix the error, split optprobe instruction recovering
   path from kprobes path.
 - Cleanup comments/styles.

Changes in v2:
 - Fix a bug to recover original instruction address in
   RIP-relative instruction fixup.
 - Moved on tip/master.
Signed-off-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: systemtap@sourceware.org
Cc: anderson@redhat.com
Link: http://lkml.kernel.org/r/20120305133209.5982.36568.stgit@localhost.localdomainSigned-off-by: NIngo Molnar <mingo@elte.hu>

It turned out that a performance counter on AMD does not
count at all when the GO or HO bit is set in the control
register and SVM is disabled in EFER.

This patch works around this issue by masking out the HO bit
in the performance counter control register when SVM is not
enabled.

The GO bit is not touched because it is only set when the
user wants to count in guest-mode only. So when SVM is
disabled the counter should not run at all and the
not-counting is the intended behaviour.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Avi Kivity <avi@redhat.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: stable@vger.kernel.org # v3.2
Link: http://lkml.kernel.org/r/1330523852-19566-1-git-send-email-joerg.roedel@amd.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

static keys: Introduce 'struct static_key', static_key_true()/false() and static_key_slow_[inc|dec]()

So here's a boot tested patch on top of Jason's series that does
all the cleanups I talked about and turns jump labels into a
more intuitive to use facility. It should also address the
various misconceptions and confusions that surround jump labels.

Typical usage scenarios:

        #include <linux/static_key.h>

        struct static_key key = STATIC_KEY_INIT_TRUE;

        if (static_key_false(&key))
                do unlikely code
        else
                do likely code

Or:

        if (static_key_true(&key))
                do likely code
        else
                do unlikely code

The static key is modified via:

        static_key_slow_inc(&key);
        ...
        static_key_slow_dec(&key);

The 'slow' prefix makes it abundantly clear that this is an
expensive operation.

I've updated all in-kernel code to use this everywhere. Note
that I (intentionally) have not pushed through the rename
blindly through to the lowest levels: the actual jump-label
patching arch facility should be named like that, so we want to
decouple jump labels from the static-key facility a bit.

On non-jump-label enabled architectures static keys default to
likely()/unlikely() branches.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NJason Baron <jbaron@redhat.com>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Cc: a.p.zijlstra@chello.nl
Cc: mathieu.desnoyers@efficios.com
Cc: davem@davemloft.net
Cc: ddaney.cavm@gmail.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20120222085809.GA26397@elte.huSigned-off-by: NIngo Molnar <mingo@elte.hu>

141168c3 ("x86: Simplify code by removing a !SMP #ifdefs
from 'struct cpuinfo_x86'") removed a bunch of CONFIG_SMP ifdefs
around code touching struct cpuinfo_x86 members but also caused
the following build error with Randy's randconfigs:

mce_amd.c:(.cpuinit.text+0x4723): undefined reference to `cpu_llc_shared_map'

Restore the #ifdef in threshold_create_bank() which creates
symlinks on the non-BSP CPUs.

There's a better patch series being worked on by Kevin Winchester
which will solve this in a cleaner fashion, but that series is
too ambitious for v3.3 merging - so we first queue up this trivial
fix and then do the rest for v3.4.
Signed-off-by: NBorislav Petkov <bp@alien8.de>
Acked-by: NKevin Winchester <kjwinchester@gmail.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Nick Bowler <nbowler@elliptictech.com>
Link: http://lkml.kernel.org/r/20120203191801.GA2846@x1.osrc.amd.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

(And define it properly for x86-32, which had its 'current_task'
declaration in separate from x86-64)

Bitten by my dislike for modules on the machines I use, and the fact
that apparently nobody else actually wanted to test the patches I sent
out.

Snif. Nobody else cares.

Anyway, we probably should uninline the 'kernel_fpu_begin()' function
that is what modules actually use and that references this, but this is
the minimal fix for now.
Reported-by: NJosh Boyer <jwboyer@gmail.com>
Reported-and-tested-by: NJongman Heo <jongman.heo@samsung.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Linus noticed that the cmp used to check if the code segment is
__KERNEL_CS or not did not specify a size. Perhaps it does not matter
as H. Peter Anvin noted that user space can not set the bottom two
bits of the %cs register. But it's best not to let the assembly choose
and change things between different versions of gas, but instead just
pick the size.

Four bytes are used to compare the saved code segment against
__KERNEL_CS. Perhaps this might mess up Xen, but we can fix that when
the time comes.

Also I noticed that there was another non-specified cmp that checks
the special stack variable if it is 1 or 0. This too probably doesn't
matter what cmp is used, but this patch uses cmpl just to make it non
ambiguous.

Link: http://lkml.kernel.org/r/CA+55aFxfAn9MWRgS3O5k2tqN5ys1XrhSFVO5_9ZAoZKDVgNfGA@mail.gmail.comSuggested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

This makes us recognize when we try to restore FPU state that matches
what we already have in the FPU on this CPU, and avoids the restore
entirely if so.

To do this, we add two new data fields:

 - a percpu 'fpu_owner_task' variable that gets written any time we
   update the "has_fpu" field, and thus acts as a kind of back-pointer
   to the task that owns the CPU.  The exception is when we save the FPU
   state as part of a context switch - if the save can keep the FPU
   state around, we leave the 'fpu_owner_task' variable pointing at the
   task whose FP state still remains on the CPU.

 - a per-thread 'last_cpu' field, that indicates which CPU that thread
   used its FPU on last.  We update this on every context switch
   (writing an invalid CPU number if the last context switch didn't
   leave the FPU in a lazily usable state), so we know that *that*
   thread has done nothing else with the FPU since.

These two fields together can be used when next switching back to the
task to see if the CPU still matches: if 'fpu_owner_task' matches the
task we are switching to, we know that no other task (or kernel FPU
usage) touched the FPU on this CPU in the meantime, and if the current
CPU number matches the 'last_cpu' field, we know that this thread did no
other FP work on any other CPU, so the FPU state on the CPU must match
what was saved on last context switch.

In that case, we can avoid the 'f[x]rstor' entirely, and just clear the
CR0.TS bit.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This inlines what is usually just a couple of instructions, but more
importantly it also fixes the theoretical error case (can that FPU
restore really ever fail? Maybe we should remove the checking).

We can't start sending signals from within the scheduler, we're much too
deep in the kernel and are holding the runqueue lock etc.  So don't
bother even trying.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This makes sure we clear the FPU usage counter for newly created tasks,
just so that we start off in a known state (for example, don't try to
preload the FPU state on the first task switch etc).

It also fixes a thinko in when we increment the fpu_counter at task
switch time, introduced by commit 34ddc81a ("i387: re-introduce FPU
state preloading at context switch time").  We should increment the
*new* task fpu_counter, not the old task, and only if we decide to use
that state (whether lazily or preloaded).
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

[Pls also look at https://lkml.org/lkml/2012/2/10/228]

Using of PAT to change pages from WB to WC works quite nicely.
Changing it back to WB - not so much. The crux of the matter is
that the code that does this (__page_change_att_set_clr) has only
limited information so when it tries to the change it gets
the "raw" unfiltered information instead of the properly filtered one -
and the "raw" one tell it that PSE bit is on (while infact it
is not).  As a result when the PTE is set to be WB from WC, we get
tons of:

:WARNING: at arch/x86/xen/mmu.c:475 xen_make_pte+0x67/0xa0()
:Hardware name: HP xw4400 Workstation
.. snip..
:Pid: 27, comm: kswapd0 Tainted: G        W    3.2.2-1.fc16.x86_64 #1
:Call Trace:
: [<ffffffff8106dd1f>] warn_slowpath_common+0x7f/0xc0
: [<ffffffff8106dd7a>] warn_slowpath_null+0x1a/0x20
: [<ffffffff81005a17>] xen_make_pte+0x67/0xa0
: [<ffffffff810051bd>] __raw_callee_save_xen_make_pte+0x11/0x1e
: [<ffffffff81040e15>] ? __change_page_attr_set_clr+0x9d5/0xc00
: [<ffffffff8114c2e8>] ? __purge_vmap_area_lazy+0x158/0x1d0
: [<ffffffff8114cca5>] ? vm_unmap_aliases+0x175/0x190
: [<ffffffff81041168>] change_page_attr_set_clr+0x128/0x4c0
: [<ffffffff81041542>] set_pages_array_wb+0x42/0xa0
: [<ffffffff8100a9b2>] ? check_events+0x12/0x20
: [<ffffffffa0074d4c>] ttm_pages_put+0x1c/0x70 [ttm]
: [<ffffffffa0074e98>] ttm_page_pool_free+0xf8/0x180 [ttm]
: [<ffffffffa0074f78>] ttm_pool_mm_shrink+0x58/0x90 [ttm]
: [<ffffffff8112ba04>] shrink_slab+0x154/0x310
: [<ffffffff8112f17a>] balance_pgdat+0x4fa/0x6c0
: [<ffffffff8112f4b8>] kswapd+0x178/0x3d0
: [<ffffffff815df134>] ? __schedule+0x3d4/0x8c0
: [<ffffffff81090410>] ? remove_wait_queue+0x50/0x50
: [<ffffffff8112f340>] ? balance_pgdat+0x6c0/0x6c0
: [<ffffffff8108fb6c>] kthread+0x8c/0xa0

for every page. The proper fix for this is has been posted
and is https://lkml.org/lkml/2012/2/10/228
"x86/cpa: Use pte_attrs instead of pte_flags on CPA/set_p.._wb/wc operations."
along with a detailed description of the problem and solution.

But since that posting has gone nowhere I am proposing
this band-aid solution so that at least users don't get
the page corruption (the pages that are WC don't get changed to WB
and end up being recycled for filesystem or other things causing
mysterious crashes).

The negative impact of this patch is that users of WC flag
(which are InfiniBand, radeon, nouveau drivers) won't be able
to set that flag - so they are going to see performance degradation.
But stability is more important here.

Fixes RH BZ# 742032, 787403, and 745574
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

commit 7347b408 "xen: Allow
unprivileged Xen domains to create iomap pages" added a redundant
line in the early bootup code to filter out the PTE. That
filtering is already done a bit earlier so this extra processing
is not required.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Currently, the NMI handler tests if it is nested by checking the
special variable saved on the stack (set during NMI handling)
and whether the saved stack is the NMI stack as well (to prevent
the race when the variable is set to zero).

But userspace may set their %rsp to any value as long as they do
not derefence it, and it may make it point to the NMI stack,
which will prevent NMIs from triggering while the userspace app
is running. (I tested this, and it is indeed the case)

Add another check to determine nested NMIs by looking at the
saved %cs (code segment register) and making sure that it is the
kernel code segment.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1329687817.1561.27.camel@acer.local.homeSigned-off-by: NIngo Molnar <mingo@elte.hu>

After all the FPU state cleanups and finally finding the problem that
caused all our FPU save/restore problems, this re-introduces the
preloading of FPU state that was removed in commit b3b0870e ("i387:
do not preload FPU state at task switch time").

However, instead of simply reverting the removal, this reimplements
preloading with several fixes, most notably

 - properly abstracted as a true FPU state switch, rather than as
   open-coded save and restore with various hacks.

   In particular, implementing it as a proper FPU state switch allows us
   to optimize the CR0.TS flag accesses: there is no reason to set the
   TS bit only to then almost immediately clear it again.  CR0 accesses
   are quite slow and expensive, don't flip the bit back and forth for
   no good reason.

 - Make sure that the same model works for both x86-32 and x86-64, so
   that there are no gratuitous differences between the two due to the
   way they save and restore segment state differently due to
   architectural differences that really don't matter to the FPU state.

 - Avoid exposing the "preload" state to the context switch routines,
   and in particular allow the concept of lazy state restore: if nothing
   else has used the FPU in the meantime, and the process is still on
   the same CPU, we can avoid restoring state from memory entirely, just
   re-expose the state that is still in the FPU unit.

   That optimized lazy restore isn't actually implemented here, but the
   infrastructure is set up for it.  Of course, older CPU's that use
   'fnsave' to save the state cannot take advantage of this, since the
   state saving also trashes the state.

In other words, there is now an actual _design_ to the FPU state saving,
rather than just random historical baggage.  Hopefully it's easier to
follow as a result.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This moves the bit that indicates whether a thread has ownership of the
FPU from the TS_USEDFPU bit in thread_info->status to a word of its own
(called 'has_fpu') in task_struct->thread.has_fpu.

This fixes two independent bugs at the same time:

 - changing 'thread_info->status' from the scheduler causes nasty
   problems for the other users of that variable, since it is defined to
   be thread-synchronous (that's what the "TS_" part of the naming was
   supposed to indicate).

   So perfectly valid code could (and did) do

	ti->status |= TS_RESTORE_SIGMASK;

   and the compiler was free to do that as separate load, or and store
   instructions.  Which can cause problems with preemption, since a task
   switch could happen in between, and change the TS_USEDFPU bit. The
   change to TS_USEDFPU would be overwritten by the final store.

   In practice, this seldom happened, though, because the 'status' field
   was seldom used more than once, so gcc would generally tend to
   generate code that used a read-modify-write instruction and thus
   happened to avoid this problem - RMW instructions are naturally low
   fat and preemption-safe.

 - On x86-32, the current_thread_info() pointer would, during interrupts
   and softirqs, point to a *copy* of the real thread_info, because
   x86-32 uses %esp to calculate the thread_info address, and thus the
   separate irq (and softirq) stacks would cause these kinds of odd
   thread_info copy aliases.

   This is normally not a problem, since interrupts aren't supposed to
   look at thread information anyway (what thread is running at
   interrupt time really isn't very well-defined), but it confused the
   heck out of irq_fpu_usable() and the code that tried to squirrel
   away the FPU state.

   (It also caused untold confusion for us poor kernel developers).

It also turns out that using 'task_struct' is actually much more natural
for most of the call sites that care about the FPU state, since they
tend to work with the task struct for other reasons anyway (ie
scheduling).  And the FPU data that we are going to save/restore is
found there too.

Thanks to Arjan Van De Ven <arjan@linux.intel.com> for pointing us to
the %esp issue.

Cc: Arjan van de Ven <arjan@linux.intel.com>
Reported-and-tested-by: NRaphael Prevost <raphael@buro.asia>
Acked-and-tested-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Tested-by: NPeter Anvin <hpa@zytor.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The AMD K7/K8 CPUs don't save/restore FDP/FIP/FOP unless an exception is
pending.  In order to not leak FIP state from one process to another, we
need to do a floating point load after the fxsave of the old process,
and before the fxrstor of the new FPU state.  That resets the state to
the (uninteresting) kernel load, rather than some potentially sensitive
user information.

We used to do this directly after the FPU state save, but that is
actually very inconvenient, since it

 (a) corrupts what is potentially perfectly good FPU state that we might
     want to lazy avoid restoring later and

 (b) on x86-64 it resulted in a very annoying ordering constraint, where
     "__unlazy_fpu()" in the task switch needs to be delayed until after
     the DS segment has been reloaded just to get the new DS value.

Coupling it to the fxrstor instead of the fxsave automatically avoids
both of these issues, and also ensures that we only do it when actually
necessary (the FP state after a save may never actually get used).  It's
simply a much more natural place for the leaked state cleanup.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Yes, taking the trap to re-load the FPU/MMX state is expensive, but so
is spending several days looking for a bug in the state save/restore
code.  And the preload code has some rather subtle interactions with
both paravirtualization support and segment state restore, so it's not
nearly as simple as it should be.

Also, now that we no longer necessarily depend on a single bit (ie
TS_USEDFPU) for keeping track of the state of the FPU, we migth be able
to do better.  If we are really switching between two processes that
keep touching the FP state, save/restore is inevitable, but in the case
of having one process that does most of the FPU usage, we may actually
be able to do much better than the preloading.

In particular, we may be able to keep track of which CPU the process ran
on last, and also per CPU keep track of which process' FP state that CPU
has.  For modern CPU's that don't destroy the FPU contents on save time,
that would allow us to do a lazy restore by just re-enabling the
existing FPU state - with no restore cost at all!
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This creates three helper functions that do the TS_USEDFPU accesses, and
makes everybody that used to do it by hand use those helpers instead.

In addition, there's a couple of helper functions for the "change both
CR0.TS and TS_USEDFPU at the same time" case, and the places that do
that together have been changed to use those.  That means that we have
fewer random places that open-code this situation.

The intent is partly to clarify the code without actually changing any
semantics yet (since we clearly still have some hard to reproduce bug in
this area), but also to make it much easier to use another approach
entirely to caching the CR0.TS bit for software accesses.

Right now we use a bit in the thread-info 'status' variable (this patch
does not change that), but we might want to make it a full field of its
own or even make it a per-cpu variable.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Touching TS_USEDFPU without touching CR0.TS is confusing, so don't do
it.  By moving it into the callers, we always do the TS_USEDFPU next to
the CR0.TS accesses in the source code, and it's much easier to see how
the two go hand in hand.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 5b1cbac3 ("i387: make irq_fpu_usable() tests more robust")
added a sanity check to the #NM handler to verify that we never cause
the "Device Not Available" exception in kernel mode.

However, that check actually pinpointed a (fundamental) race where we do
cause that exception as part of the signal stack FPU state save/restore
code.

Because we use the floating point instructions themselves to save and
restore state directly from user mode, we cannot do that atomically with
testing the TS_USEDFPU bit: the user mode access itself may cause a page
fault, which causes a task switch, which saves and restores the FP/MMX
state from the kernel buffers.

This kind of "recursive" FP state save is fine per se, but it means that
when the signal stack save/restore gets restarted, it will now take the
'#NM' exception we originally tried to avoid.  With preemption this can
happen even without the page fault - but because of the user access, we
cannot just disable preemption around the save/restore instruction.

There are various ways to solve this, including using the
"enable/disable_page_fault()" helpers to not allow page faults at all
during the sequence, and fall back to copying things by hand without the
use of the native FP state save/restore instructions.

However, the simplest thing to do is to just allow the #NM from kernel
space, but fix the race in setting and clearing CR0.TS that this all
exposed: the TS bit changes and the TS_USEDFPU bit absolutely have to be
atomic wrt scheduling, so while the actual state save/restore can be
interrupted and restarted, the act of actually clearing/setting CR0.TS
and the TS_USEDFPU bit together must not.

Instead of just adding random "preempt_disable/enable()" calls to what
is already excessively ugly code, this introduces some helper functions
that mostly mirror the "kernel_fpu_begin/end()" functionality, just for
the user state instead.

Those helper functions should probably eventually replace the other
ad-hoc CR0.TS and TS_USEDFPU tests too, but I'll need to think about it
some more: the task switching functionality in particular needs to
expose the difference between the 'prev' and 'next' threads, while the
new helper functions intentionally were written to only work with
'current'.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The check for save_init_fpu() (introduced in commit 5b1cbac3: "i387:
make irq_fpu_usable() tests more robust") was the wrong way around, but
I hadn't noticed, because my "tests" were bogus: the FPU exceptions are
disabled by default, so even doing a divide by zero never actually
triggers this code at all unless you do extra work to enable them.

So if anybody did enable them, they'd get one spurious warning.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some code - especially the crypto layer - wants to use the x86
FP/MMX/AVX register set in what may be interrupt (typically softirq)
context.

That *can* be ok, but the tests for when it was ok were somewhat
suspect.  We cannot touch the thread-specific status bits either, so
we'd better check that we're not going to try to save FP state or
anything like that.

Now, it may be that the TS bit is always cleared *before* we set the
USEDFPU bit (and only set when we had already cleared the USEDFP
before), so the TS bit test may actually have been sufficient, but it
certainly was not obviously so.

So this explicitly verifies that we will not touch the TS_USEDFPU bit,
and adds a few related sanity-checks.  Because it seems that somehow
AES-NI is corrupting user FP state.  The cause is not clear, and this
patch doesn't fix it, but while debugging it I really wanted the code to
be more obviously correct and robust.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It was marked asmlinkage for some really old and stale legacy reasons.
Fix that and the equally stale comment.

Noticed when debugging the irq_fpu_usable() bugs.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The power and cpuidle tracepoints are called within a rcu_idle_exit()
section, and must be denoted with the _rcuidle() version of the tracepoint.
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Fix to decode grouped AVX with VEX pp bits which should be
handled as same as last-prefixes. This fixes below warnings
in posttest with CONFIG_CRYPTO_SHA1_SSSE3=y.

 Warning: arch/x86/tools/test_get_len found difference at <sha1_transform_avx>:ffffffff810d5fc0
 Warning: ffffffff810d6069:	c5 f9 73 de 04       	vpsrldq $0x4,%xmm6,%xmm0
 Warning: objdump says 5 bytes, but insn_get_length() says 4
 ...

With this change, test_get_len can decode it correctly.

 $ arch/x86/tools/test_get_len -v -y
 ffffffff810d6069:       c5 f9 73 de 04          vpsrldq $0x4,%xmm6,%xmm0
 Succeed: decoded and checked 1 instructions
Reported-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: yrl.pp-manager.tt@hitachi.com
Link: http://lkml.kernel.org/r/20120210053340.30429.73410.stgit@localhost.localdomainSigned-off-by: NIngo Molnar <mingo@elte.hu>

For L1 instruction cache and L2 cache the shared CPU information
is wrong. On current AMD family 15h CPUs those caches are shared
between both cores of a compute unit.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=42607Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Cc: Petkov Borislav <Borislav.Petkov@amd.com>
Cc: Dave Jones <davej@redhat.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/20120208195229.GA17523@alberich.amd.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

The following patch fixes a bug introduced by the following
commit:

        e050e3f0 ("perf: Fix broken interrupt rate throttling")

The patch caused the following warning to pop up depending on
the sampling frequency adjustments:

  ------------[ cut here ]------------
  WARNING: at arch/x86/kernel/cpu/perf_event.c:995 x86_pmu_start+0x79/0xd4()

It was caused by the following call sequence:

perf_adjust_freq_unthr_context.part() {
     stop()
     if (delta > 0) {
          perf_adjust_period() {
              if (period > 8*...) {
                  stop()
                  ...
                  start()
              }
          }
      }
      start()
}

Which caused a double start and a double stop, thus triggering
the assert in x86_pmu_start().

The patch fixes the problem by avoiding the double calls. We
pass a new argument to perf_adjust_period() to indicate whether
or not the event is already stopped. We can't just remove the
start/stop from that function because it's called from
__perf_event_overflow where the event needs to be reloaded via a
stop/start back-toback call.

The patch reintroduces the assertion in x86_pmu_start() which
was removed by commit:

	84f2b9b2 ("perf: Remove deprecated WARN_ON_ONCE()")

In this second version, we've added calls to disable/enable PMU
during unthrottling or frequency adjustment based on bug report
of spurious NMI interrupts from Eric Dumazet.
Reported-and-tested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NStephane Eranian <eranian@google.com>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: markus@trippelsdorf.de
Cc: paulus@samba.org
Link: http://lkml.kernel.org/r/20120207133956.GA4932@quad
[ Minor edits to the changelog and to the code ]
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Stephane Eranian reported that doing a scheduler latency
measurements with perf on AMD doesn't work out as expected due
to the fact that the sched_clock() granularity is too coarse,
i.e. done in jiffies due to the sched_clock_stable not set,
which, if set, would mean that we get to use the TSC as sample
source which would give us much higher precision.

However, there's no reason not to set sched_clock_stable on AMD
because all families from F10h and upwards do have an invariant
TSC and have the CPUID flag to prove (CPUID_8000_0007_EDX[8]).

Make it so, #1.
Signed-off-by: NBorislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Venki Pallipadi <venki@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Link: http://lkml.kernel.org/r/20120206132546.GA30854@quad
[ Should any non-standard system break the TSC, we should
  mark them so explicitly, in their platform init handler, or
  in a DMI quirk. ]
Signed-off-by: NIngo Molnar <mingo@elte.hu>

AMD processors will never support /dev/cpu/microcode updating so
just silently fail instead of printing out a warning for every
cpu.
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1328552935-965-1-git-send-email-prarit@redhat.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

CC: stable@kernel.org #2.6.37 and onwards
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

When a user offlines a VCPU and then onlines it, we get:

NMI watchdog disabled (cpu2): hardware events not enabled
BUG: scheduling while atomic: swapper/2/0/0x00000002
Modules linked in: dm_multipath dm_mod xen_evtchn iscsi_boot_sysfs iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi scsi_mod libcrc32c crc32c radeon fbco
 ttm bitblit softcursor drm_kms_helper xen_blkfront xen_netfront xen_fbfront fb_sys_fops sysimgblt sysfillrect syscopyarea xen_kbdfront xenfs [last unloaded:

Pid: 0, comm: swapper/2 Tainted: G           O 3.2.0phase15.1-00003-gd6f7f5b-dirty #4
Call Trace:
 [<ffffffff81070571>] __schedule_bug+0x61/0x70
 [<ffffffff8158eb78>] __schedule+0x798/0x850
 [<ffffffff8158ed6a>] schedule+0x3a/0x50
 [<ffffffff810349be>] cpu_idle+0xbe/0xe0
 [<ffffffff81583599>] cpu_bringup_and_idle+0xe/0x10

The reason for this should be obvious from this call-chain:
cpu_bringup_and_idle:
 \- cpu_bringup
  |   \-[preempt_disable]
  |
  |- cpu_idle
       \- play_dead [assuming the user offlined the VCPU]
       |     \
       |     +- (xen_play_dead)
       |          \- HYPERVISOR_VCPU_off [so VCPU is dead, once user
       |          |                       onlines it starts from here]
       |          \- cpu_bringup [preempt_disable]
       |
       +- preempt_enable_no_reschedule()
       +- schedule()
       \- preempt_enable()

So we have two preempt_disble() and one preempt_enable(). Calling
preempt_enable() after the cpu_bringup() in the xen_play_dead
fixes the imbalance.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

With the new throttling/unthrottling code introduced with
commit:

  e050e3f0 ("perf: Fix broken interrupt rate throttling")

we occasionally hit two WARN_ON_ONCE() checks in:

  - intel_pmu_pebs_enable()
  - intel_pmu_lbr_enable()
  - x86_pmu_start()

The assertions are no longer problematic. There is a valid
path where they can trigger but it is harmless.

The assertion can be triggered with:

  $ perf record -e instructions:pp ....

Leading to paths:

  intel_pmu_pebs_enable
  intel_pmu_enable_event
  x86_perf_event_set_period
  x86_pmu_start
  perf_adjust_freq_unthr_context
  perf_event_task_tick
  scheduler_tick

And:

  intel_pmu_lbr_enable
  intel_pmu_enable_event
  x86_perf_event_set_period
  x86_pmu_start
  perf_adjust_freq_unthr_context.
  perf_event_task_tick
  scheduler_tick

cpuc->enabled is always on because when we get to
perf_adjust_freq_unthr_context() the PMU is not totally
disabled. Furthermore when we need to adjust a period,
we only stop the event we need to change and not the
entire PMU. Thus, when we re-enable, cpuc->enabled is
already set. Note that when we stop the event, both
pebs and lbr are stopped if necessary (and possible).
Signed-off-by: NStephane Eranian <eranian@google.com>
Cc: peterz@infradead.org
Link: http://lkml.kernel.org/r/20120202110401.GA30911@quadSigned-off-by: NIngo Molnar <mingo@elte.hu>

Return to behaviour perf MSR had before introducing vPMU in case vPMU
is disabled. Some guests access those registers unconditionally and do
not expect it to fail.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

On hosts without this patch, 32bit guests will crash (and 64bit guests
may behave in a wrong way) for example by simply executing following
nasm-demo-application:

    [bits 32]
    global _start
    SECTION .text
    _start: syscall

(I tested it with winxp and linux - both always crashed)

    Disassembly of section .text:

    00000000 <_start>:
       0:   0f 05                   syscall

The reason seems a missing "invalid opcode"-trap (int6) for the
syscall opcode "0f05", which is not available on Intel CPUs
within non-longmodes, as also on some AMD CPUs within legacy-mode.
(depending on CPU vendor, MSR_EFER and cpuid)

Because previous mentioned OSs may not engage corresponding
syscall target-registers (STAR, LSTAR, CSTAR), they remain
NULL and (non trapping) syscalls are leading to multiple
faults and finally crashs.

Depending on the architecture (AMD or Intel) pretended by
guests, various checks according to vendor's documentation
are implemented to overcome the current issue and behave
like the CPUs physical counterparts.

[mtosatti: cleanup/beautify code]
Signed-off-by: NStephan Baerwolf <stephan.baerwolf@tu-ilmenau.de>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

In order to be able to proceed checks on CPU-specific properties
within the emulator, function "get_cpuid" is introduced.
With "get_cpuid" it is possible to virtually call the guests
"cpuid"-opcode without changing the VM's context.

[mtosatti: cleanup/beautify code]
Signed-off-by: NStephan Baerwolf <stephan.baerwolf@tu-ilmenau.de>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>