After enabling per-cpu processing it appeared that under heavy load
changing MTU can result in blocking all port's interrupts and
transmitting data is not possible after the change.

This commit fixes above issue by disabling percpu interrupts for the
time, when TXQs and RXQs are reconfigured.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Giuseppe Cavallaro says:

====================
stmmac MDIO and normal descr fixes

This patch series is to fix the problems below and recently debugged
in this mailing list:

o to fix a problem for the HW where the normal descriptor
o to fix the mdio registration according to the different
  platform configurations

I am resending all the patches again: built on top of net.git repo.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initially the phy_bus_name was added to manipulate the
driver name but it was recently just used to manage the
fixed-link and then to take some decision at run-time.
So the patch uses the is_pseudo_fixed_link and removes
the phy_bus_name variable not necessary anymore.

The driver can manage the mdio registration by using phy-handle,
dwmac-mdio and own parameter e.g. snps,phy-addr.
This patch takes care about all these possible configurations
and fixes the mdio registration in case of there is a real
transceiver or a switch (that needs to be managed by using
fixed-link).
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: NAndreas Färber <afaerber@suse.de>
Tested-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Phil Reid <preid@electromag.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 88f8b1bb.
due to problems on GeekBox and Banana Pi M1 board when
connected to a real transceiver instead of a switch via
fixed-link.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixs a regression raised when test on chips that use
the normal descriptor layout. In fact, no len bits were set for
the TDES1 and no OWN bit inside the TDES0.
Signed-off-by: NGiuseppe CAVALLARO <peppe.cavallaro@st.com>
Tested-by: NAndreas Färber <afaerber@suse.de>
Cc: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

L1_CACHE_BYTES may not be the real cacheline size, use cache_line_size
to determine the cacheline size in runtime.
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Suggested-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

L1_CACHE_BYTES may not be the real cacheline size, use cache_line_size
to determine the cacheline size in runtime.
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Suggested-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is to fix the following maybe-uninitialized warning:

drivers/net/ethernet/marvell/mvpp2.c:6007:18: warning: 'err' may be
used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sasha Levin reported a suspicious rcu_dereference_protected() warning
found while fuzzing with trinity that is similar to this one:

  [   52.765684] net/core/filter.c:2262 suspicious rcu_dereference_protected() usage!
  [   52.765688] other info that might help us debug this:
  [   52.765695] rcu_scheduler_active = 1, debug_locks = 1
  [   52.765701] 1 lock held by a.out/1525:
  [   52.765704]  #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff816a64b7>] rtnl_lock+0x17/0x20
  [   52.765721] stack backtrace:
  [   52.765728] CPU: 1 PID: 1525 Comm: a.out Not tainted 4.5.0+ #264
  [...]
  [   52.765768] Call Trace:
  [   52.765775]  [<ffffffff813e488d>] dump_stack+0x85/0xc8
  [   52.765784]  [<ffffffff810f2fa5>] lockdep_rcu_suspicious+0xd5/0x110
  [   52.765792]  [<ffffffff816afdc2>] sk_detach_filter+0x82/0x90
  [   52.765801]  [<ffffffffa0883425>] tun_detach_filter+0x35/0x90 [tun]
  [   52.765810]  [<ffffffffa0884ed4>] __tun_chr_ioctl+0x354/0x1130 [tun]
  [   52.765818]  [<ffffffff8136fed0>] ? selinux_file_ioctl+0x130/0x210
  [   52.765827]  [<ffffffffa0885ce3>] tun_chr_ioctl+0x13/0x20 [tun]
  [   52.765834]  [<ffffffff81260ea6>] do_vfs_ioctl+0x96/0x690
  [   52.765843]  [<ffffffff81364af3>] ? security_file_ioctl+0x43/0x60
  [   52.765850]  [<ffffffff81261519>] SyS_ioctl+0x79/0x90
  [   52.765858]  [<ffffffff81003ba2>] do_syscall_64+0x62/0x140
  [   52.765866]  [<ffffffff817d563f>] entry_SYSCALL64_slow_path+0x25/0x25

Same can be triggered with PROVE_RCU (+ PROVE_RCU_REPEATEDLY) enabled
from tun_attach_filter() when user space calls ioctl(tun_fd, TUN{ATTACH,
DETACH}FILTER, ...) for adding/removing a BPF filter on tap devices.

Since the fix in f91ff5b9 ("net: sk_{detach|attach}_filter() rcu
fixes") sk_attach_filter()/sk_detach_filter() now dereferences the
filter with rcu_dereference_protected(), checking whether socket lock
is held in control path.

Since its introduction in 99405162 ("tun: socket filter support"),
tap filters are managed under RTNL lock from __tun_chr_ioctl(). Thus the
sock_owned_by_user(sk) doesn't apply in this specific case and therefore
triggers the false positive.

Extend the BPF API with __sk_attach_filter()/__sk_detach_filter() pair
that is used by tap filters and pass in lockdep_rtnl_is_held() for the
rcu_dereference_protected() checks instead.
Reported-by: NSasha Levin <sasha.levin@oracle.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Telit LE910 V2 is a mobile broadband card with no ARP capabilities:
the patch makes this device to use wwan_noarp_info struct
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Reviewed-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Size of the attribute IFLA_PHYS_PORT_NAME was missing.

Fixes: db24a904 ("net: add support for phys_port_name")
CC: David Ahern <dsahern@gmail.com>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 55cd48c8 ("net: fec: stop the "rcv is not +last, " error
messages") introduces a write to a register that does not exist in
Coldfire.

Move the FEC_FTRL register access inside the FEC_QUIRK_HAS_RACC 'if' block,
so that we guarantee it will not be used on Coldfire CPUs.
Reported-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvneta is also used in some Marvell berlin family SoCs which may
have 64bytes cacheline size. Replace the MVNETA_CPU_D_CACHE_LINE_SIZE
usage with L1_CACHE_BYTES.

And since dma_alloc_coherent() is always cacheline size aligned, so
remove the align checks.
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvpp2 ip maybe used in SoCs which may have have 64bytes cacheline
size. Replace the MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES.

And since dma_alloc_coherent() is always cacheline size aligned, so
remove the align checks.
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of the vendor-specific bootloaders set up this part
of the initialization for us, so this was never added.
However, since upstream bootloaders don't initialize the
chip specifically, they leave the fiber MII's PDOWN flag
set, which means that the CPU port doesn't connect.

This patch checks whether this flag has been clear prior
by something else, and if not make us clear it.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NPatrick Uiterwijk <patrick@puiterwijk.org>
Tested-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add versions of the phy_page_read and _write functions to
be used in a context where the SMI mutex is held.
Tested-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NPatrick Uiterwijk <patrick@puiterwijk.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2016-03-29

This series contains fixes to ixgbe and ixgbevf.

Tushar fixes an issue which was introduced with an earlier commit, where
hardware register RAR0 default MAC address does not get set properly.

Alex fixes two issues, first being the VXLAN port number should be stored
in network order instead of in host order.  The second fix corrects the ATR
code to handle IPv6 extension headers.  The issue was ATR code was assuming
that it would be able to use tcp_hdr for every TCP frame that came through,
but that is not the case, which resulted in bad filters being setup.

Mark fixes a use of usleep_range() to udelay() in the case where a lock
is being held.

Stefan fixes the offline self tests where ndo_stop() should be used instead
of ndo_close(), which causes IFF_UP to be cleared and interface routes get
removed.

Emil fixes the error case where we need to return an error when a MAC
address change is rejected by the PF.  This helps prevent the user from
modifying the MAC address when the operation is not permitted.

Sridhar provides three fixes for ixgbe, all dealing with traffic class
offload handling.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the 2 byte padding in struct bpf_tunnel_key between tunnel_ttl
and tunnel_label members explicit. No issue has been observed, and
gcc/llvm does padding for the old struct already, where tunnel_label
was not yet present, so the current code works, but since it's part
of uapi, make sure we don't introduce holes in structs.

Therefore, add tunnel_ext that we can use generically in future
(f.e. to flag OAM messages for backends, etc). Also add the offset
to the compat tests to be sure should some compilers not padd the
tail of the old version of bpf_tunnel_key.

Fixes: 4018ab18 ("bpf: support flow label for bpf_skb_{set, get}_tunnel_key")
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IPv6 counters updates use a different macro than IPv4.

Fixes: 36cbb245 ("udp: Increment UDP_MIB_IGNOREDMULTI for arriving unmatched multicasts")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Rick Jones <rick.jones2@hp.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To report flow control tx/rx settings accurately regardless of autoneg
setting, we should use link_info->req_flow_ctrl.  Before this patch,
the reported settings were only correct when autoneg was on.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The typo caused the wrong flow control bit to be set.

Reported by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The size of every padded firmware message is specified in the first
HWRM_VER_GET response message.  Use this value to pad every message
after that.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The existing code does the following:
    allocate completion ring
    initialize completion ring doorbell
    disable interrupts on this completion ring by writing to the doorbell

We can have a race where firmware sends an asynchronous event to the host
after completion ring allocation and before doorbell is initialized.
When this happens driver can crash while ringing the doorbell using
uninitialized value as part of handling the IRQ/napi request.
Signed-off-by: NPrashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is an issue when we use mavtap over team:
When we replug nic links from team0, the real nics's mc list will not
include the maddr for macvtap any more. then we can't receive pkts to
macvtap device, as they are filterred by mc list of nic.

In Bonding Driver, it syncs the uc/mc addrs in bond_enslave().

We will fix this issue on team by adding the port's uc/mc addrs sync in
team_port_add.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch should fix the issues seen with a recent fix to prevent
tunnel-in-tunnel frames from being generated with GRO.  The fix itself is
correct for now as long as we do not add any devices that support
NETIF_F_GSO_GRE_CSUM.  When such a device is added it could have the
potential to mess things up due to the fact that the outer transport header
points to the outer UDP header and not the GRE header as would be expected.

Fixes: fac8e0f5 ("tunnels: Don't apply GRO to multiple layers of encapsulation.")
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

in the case where qed_slowpath_irq_req is not called, rc is not
assigned and so qed_int_igu_enable will return a garbage value.
Fix this by initializing rc to 0.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Somehow my patch for commit cea8768f ("sctp: allow
sctp_transmit_packet and others to use gfp") missed two important
chunks, which are now added.

Fixes: cea8768f ("sctp: allow sctp_transmit_packet and others to use gfp")
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-By: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When NET_SWITCHDEV=n, switchdev_port_attr_set will return -EOPNOTSUPP,
we should ignore this error code and continue to set the ageing time.

Fixes: c62987bb ("bridge: push bridge setting ageing_time down to switchdev")
Signed-off-by: NHaishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix support for 16 bit source/dest port matches in ixgbe model.
u32 uses a single 32-bit key value for both source and destination ports
starting at offset 0. So replace the 2 functions with a single function
that takes this key value/mask to program both source and dest ports.

Verified with the following filter:

 #tc qdisc add dev p4p1 ingress
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 1: u32 divisor 1
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:10 u32 ht 800: link 1: \
	offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 1:0:10 u32 ht 1: \
	match tcp src 1024 ffff match tcp dst 80 ffff action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 1:0:11 u32 ht 1: \
	match tcp src 1025 ffff action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 1:0:12 u32 ht 1: \
	match tcp dst 81 ffff action drop
Signed-off-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the incorrect check for mask in ixgbe_configure_clsu32 and
drop the 'mask' field that is not required in struct ixgbe_mat_field

Verified with the following filters:

 #tc qdisc add dev p4p1 ingress
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:1 u32 ht 800: \
	match ip dst 10.0.0.1/8 match ip src 10.0.0.2/8 action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:2 u32 ht 800: \
	match ip dst 11.0.0.1/16 match ip src 11.0.0.2/16 action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:3 u32 ht 800: \
	match ip dst 12.0.0.1/24 match ip src 12.0.0.2/24 action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:4 u32 ht 800: \
	match ip dst 13.0.0.1/32 match ip src 13.0.0.2/32 action drop
Signed-off-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Check for handle ids when adding/deleting hash nodes OR adding/deleting
filter entries and limit them to max number of links or header nodes
supported(IXGBE_MAX_LINK_HANDLE).

Start from bit 0 when setting hash table bit-map.(adapter->tables)
Signed-off-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This function is only used in ixgbe_main.c
Resolves a "missing prototype" warning when building the driver with W=1
Reported-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Return error when a MAC address change is rejected by the PF.

This will prevent the user from modifying the MAC address when
that operation is not permitted.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use udelay instead of usleep_range because this can be called while
a lock is held.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ATR code was assuming that it would be able to use tcp_hdr for
every TCP frame that came through.  However this isn't the case as it
is possible for a frame to arrive that is TCP but sent through something
like a raw socket.  As a result the driver was setting up bad filters in
which tcp_hdr was really pointing to the network header so the data was
all invalid.

In order to correct this I have added a bit of parsing logic that will
determine the TCP header location based off of the network header and
either the offset in the case of the IPv4 header, or a walk through the
IPv6 extension headers until it encounters the header that indicates
IPPROTO_TCP.  In addition I have added checks to verify that the lowest
protocol provided is recognized as IPv4 or IPv6 to help mitigate raw
sockets using ETH_P_ALL from having ATR applied to them.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VXLAN port number should be stored in network order instead of in host
order as it is accessed from the hot-path in ATR.  This way we can avoid
having to do any byte swaps in order to validate the port number.

I moved the vxlan_port value into a hole in the read-mostly region of the
adapter struct.  This way it should be in a warm cache-line instead of in
some isolated region in memory when it needs to be accessed.

In addition I went through and stripped a bunch of unneeded ifdef flags
since having an extra variable present doesn't really hurt anything and
makes the code easier to read.  I also went through and dropped the
NETIF_F_RXCSUM flag which was being set in hw_encap_features but provides
no value as the flag is not evaluated in the Rx path.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

commit c9f53e63 ("ixgbe: Refactor MAC address configuration code")
introduced code that doesn't set HW register RAR0 to default mac address
but FF:FF:FF:FF:FF:FF. Due to this, ixgbe HW discards all incoming packets
that doesn't have destination mac address equals to FF:FF:FF:FF:FF:FF.

This commit sets RAR0 correctly to default HW mac address.
Signed-off-by: NTushar Dave <tushar.n.dave@oracle.com>
Tested-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Thomas reports:
"Windows:

00 diagnostics
01 modem
02 at-port
03 nmea
04 nic

Linux:

T:  Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=2001 ProdID=7e19 Rev=02.32
S:  Manufacturer=Mobile Connect
S:  Product=Mobile Connect
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage"
Reported-by: NThomas Schäfer <tschaefer@t-online.de>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>