1. 16 6月, 2016 29 次提交
    • E
      net_sched: sch_pie: defer skb freeing · db4879d9
      Eric Dumazet 提交于
      pie_change() can use rtnl_qdisc_drop() to benefit from
      deferred freeing.
      
      pie_reset() is already using qdisc_reset_queue()
      Signed-off-by: NEric Dumazet <edumazet@google.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      db4879d9
    • E
      net_sched: sch_netem: defer skb freeing · 2f08a9a1
      Eric Dumazet 提交于
      rtnl_kfree_skbs() can be used in tfifo_reset()
      
      It would be nice if we could iterate through rb tree instead
      of removing one skb at a time, and build a single skb chain.
      But this is left for a future patch.
      Signed-off-by: NEric Dumazet <edumazet@google.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2f08a9a1
    • E
      net_sched: sch_htb: defer skb freeing · a5a9f534
      Eric Dumazet 提交于
      Both htb_reset() and htb_destroy() can use __qdisc_reset_queue()
      instead of __skb_queue_purge() to defer skb freeing of internal
      queues.
      Signed-off-by: NEric Dumazet <edumazet@google.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a5a9f534
    • E
      net_sched: sch_hhf: defer skb freeing · e7e424cd
      Eric Dumazet 提交于
      Both hhf_reset() and hhf_change() can use rtnl_kfree_skbs()
      Signed-off-by: NEric Dumazet <edumazet@google.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      e7e424cd
    • E
      net_sched: fq_codel: defer skb freeing · ece5d4c7
      Eric Dumazet 提交于
      Both fq_codel_change() and fq_codel_reset() can use rtnl_kfree_skbs()
      Signed-off-by: NEric Dumazet <edumazet@google.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ece5d4c7
    • E
      net_sched: sch_fq: defer skb freeing · e14ffdfd
      Eric Dumazet 提交于
      Both fq_change() and fq_reset() can use rtnl_kfree_skbs()
      Signed-off-by: NEric Dumazet <edumazet@google.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      e14ffdfd
    • E
      net_sched: sch_codel: defer skb freeing in codel_change() · b3d7e2b2
      Eric Dumazet 提交于
      codel_change() can use rtnl_qdisc_drop()
      to defer expensive skb freeing after locks are released.
      
      codel_reset() already has support for deferred skb freeing
      because it uses qdisc_reset_queue()
      Signed-off-by: NEric Dumazet <edumazet@google.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b3d7e2b2
    • E
      net_sched: sch_choke: defer skb freeing · f9aed311
      Eric Dumazet 提交于
      choke_reset() and choke_change() can use rtnl_qdisc_drop()
      to defer expensive skb freeing after locks are released.
      Signed-off-by: NEric Dumazet <edumazet@google.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f9aed311
    • E
      net_sched: add the ability to defer skb freeing · 1b5c5493
      Eric Dumazet 提交于
      qdisc are changed under RTNL protection and often
      while blocking BH and root qdisc spinlock.
      
      When lots of skbs need to be dropped, we free
      them under these locks causing TX/RX freezes,
      and more generally latency spikes.
      
      This commit adds rtnl_kfree_skbs(), used to queue
      skbs for deferred freeing.
      
      Actual freeing happens right after RTNL is released,
      with appropriate scheduling points.
      
      rtnl_qdisc_drop() can also be used in place
      of disc_drop() when RTNL is held.
      
      qdisc_reset_queue() and __qdisc_reset_queue() get
      the new behavior, so standard qdiscs like pfifo, pfifo_fast...
      have their ->reset() method automatically handled.
      Signed-off-by: NEric Dumazet <edumazet@google.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      1b5c5493
    • J
      tipc: add neighbor monitoring framework · 35c55c98
      Jon Paul Maloy 提交于
      TIPC based clusters are by default set up with full-mesh link
      connectivity between all nodes. Those links are expected to provide
      a short failure detection time, by default set to 1500 ms. Because
      of this, the background load for neighbor monitoring in an N-node
      cluster increases with a factor N on each node, while the overall
      monitoring traffic through the network infrastructure increases at
      a ~(N * (N - 1)) rate. Experience has shown that such clusters don't
      scale well beyond ~100 nodes unless we significantly increase failure
      discovery tolerance.
      
      This commit introduces a framework and an algorithm that drastically
      reduces this background load, while basically maintaining the original
      failure detection times across the whole cluster. Using this algorithm,
      background load will now grow at a rate of ~(2 * sqrt(N)) per node, and
      at ~(2 * N * sqrt(N)) in traffic overhead. As an example, each node will
      now have to actively monitor 38 neighbors in a 400-node cluster, instead
      of as before 399.
      
      This "Overlapping Ring Supervision Algorithm" is completely distributed
      and employs no centralized or coordinated state. It goes as follows:
      
      - Each node makes up a linearly ascending, circular list of all its N
        known neighbors, based on their TIPC node identity. This algorithm
        must be the same on all nodes.
      
      - The node then selects the next M = sqrt(N) - 1 nodes downstream from
        itself in the list, and chooses to actively monitor those. This is
        called its "local monitoring domain".
      
      - It creates a domain record describing the monitoring domain, and
        piggy-backs this in the data area of all neighbor monitoring messages
        (LINK_PROTOCOL/STATE) leaving that node. This means that all nodes in
        the cluster eventually (default within 400 ms) will learn about
        its monitoring domain.
      
      - Whenever a node discovers a change in its local domain, e.g., a node
        has been added or has gone down, it creates and sends out a new
        version of its node record to inform all neighbors about the change.
      
      - A node receiving a domain record from anybody outside its local domain
        matches this against its own list (which may not look the same), and
        chooses to not actively monitor those members of the received domain
        record that are also present in its own list. Instead, it relies on
        indications from the direct monitoring nodes if an indirectly
        monitored node has gone up or down. If a node is indicated lost, the
        receiving node temporarily activates its own direct monitoring towards
        that node in order to confirm, or not, that it is actually gone.
      
      - Since each node is actively monitoring sqrt(N) downstream neighbors,
        each node is also actively monitored by the same number of upstream
        neighbors. This means that all non-direct monitoring nodes normally
        will receive sqrt(N) indications that a node is gone.
      
      - A major drawback with ring monitoring is how it handles failures that
        cause massive network partitionings. If both a lost node and all its
        direct monitoring neighbors are inside the lost partition, the nodes in
        the remaining partition will never receive indications about the loss.
        To overcome this, each node also chooses to actively monitor some
        nodes outside its local domain. Those nodes are called remote domain
        "heads", and are selected in such a way that no node in the cluster
        will be more than two direct monitoring hops away. Because of this,
        each node, apart from monitoring the member of its local domain, will
        also typically monitor sqrt(N) remote head nodes.
      
      - As an optimization, local list status, domain status and domain
        records are marked with a generation number. This saves senders from
        unnecessarily conveying  unaltered domain records, and receivers from
        performing unneeded re-adaptations of their node monitoring list, such
        as re-assigning domain heads.
      
      - As a measure of caution we have added the possibility to disable the
        new algorithm through configuration. We do this by keeping a threshold
        value for the cluster size; a cluster that grows beyond this value
        will switch from full-mesh to ring monitoring, and vice versa when
        it shrinks below the value. This means that if the threshold is set to
        a value larger than any anticipated cluster size (default size is 32)
        the new algorithm is effectively disabled. A patch set for altering the
        threshold value and for listing the table contents will follow shortly.
      
      - This change is fully backwards compatible.
      Acked-by: NYing Xue <ying.xue@windriver.com>
      Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      35c55c98
    • D
      net: vrf: Update flags and features settings · 7889681f
      David Ahern 提交于
      1. Default VRF devices to not having a qdisc (IFF_NO_QUEUE). Users
         can add one as desired.
      
      2. Disable adding a VLAN to a VRF device.
      
      3. Enable offloads and hardware features similar to other logical
         devices (e.g., dummy, veth)
      
      Change provides a significant boost in TCP stream Tx performance,
      from ~2,700 Mbps to ~18,100 Mbps and makes throughput close to the
      performance without a VRF (18,500 Mbps). netperf TCP_STREAM benchmark
      using qemu with virtio+vhost for the NICs
      Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7889681f
    • P
      tun: fix csum generation for tap devices · df10db98
      Paolo Abeni 提交于
      The commit 34166093 ("tuntap: use common code for virtio_net_hdr
      and skb GSO conversion") replaced the tun code for header manipulation
      with the generic helpers. While doing so, it implictly moved the
      skb_partial_csum_set() invocation after eth_type_trans(), which
      invalidate the current gso start/offset values.
      Fix it by moving the helper invocation before the mac pulling.
      
      Fixes: 34166093 ("tuntap: use common code for virtio_net_hdr and skb GSO conversion")
      Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
      Acked-by: NMike Rapoport <rppt@linux.vnet.ibm.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      df10db98
    • D
      Merge branch 'skb_array' · 829e64d1
      David S. Miller 提交于
      Michael S. Tsirkin says:
      
      ====================
      skb_array: array based FIFO for skbs
      
      This is in response to the proposal by Jason to make tun
      rx packet queue lockless using a circular buffer.
      My testing seems to show that at least for the common usecase
      in networking, which isn't lockless, circular buffer
      with indices does not perform that well, because
      each index access causes a cache line to bounce between
      CPUs, and index access causes stalls due to the dependency.
      
      By comparison, an array of pointers where NULL means invalid
      and !NULL means valid, can be updated without messing up barriers
      at all and does not have this issue.
      
      On the flip side, cache pressure may be caused by using large queues.
      tun has a queue of 1000 entries by default and that's 8K.
      At this point I'm not sure this can be solved efficiently.
      The correct solution might be sizing the queues appropriately.
      
      Here's an implementation of this idea: it can be used more
      or less whenever sk_buff_head can be used, except you need
      to know the queue size in advance.
      
      As this might be useful outside of networking, I implemented
      a generic array of void pointers, with a type-safe wrapper for skbs.
      
      It remains to be seen whether resizing is required, in case it is
      I included patches implementing resizing by holding both the
      consumer and the producer locks.
      
      I think this code works fine without any extra memory barriers since we
      always read and write the same location, so the accesses can not be
      reordered.
      Multiple writes of the same value into memory would mess things up
      for us, I don't think compilers would do it though.
      But if people feel it's better to be safe wrt compiler optimizations,
      specifying queue as volatile would probably do it in a cleaner way
      than converting all accesses to READ_ONCE/WRITE_ONCE. Thoughts?
      
      The only issue is with calls within a loop using the __ptr_ring_XXX
      accessors - in theory compiler could hoist accesses out of the loop.
      
      Following volatile-considered-harmful.txt I merely
      documented that callers that busy-poll should invoke cpu_relax().
      Most people will use the external skb_array_XXX APIs with a spinlock,
      so this should not be an issue for them.
      
      Eric Dumazet suggested adding an extra pointer to skb for when
      we have a single outstanding packet. I could not figure out
      a way to implement this without a shared consumer/producer lock
      though, which would cause cache line bounces by itself.
      
      Jesper, Jason, I know that both of you tested this,
      please post Tested-by tags for whatever was tested.
      
      changes since v7
      	fix typos noticed by Jesper Brouer
      
      changes since v6
      	resize implemented. peek/full calls are no longer lockless
      
      	replaced _FIELD macros with _CALL which invoke a function
      	on the pointer rather than just returning a value
      
      	destroy now scans the array and frees all queued skbs
      
      changes since v5
      	implemented a generic ptr_ring api, and
      		made skb_array a type-safe wrapper
      	apis for taking the spinlock in different contexts
      		following expected usecase in tun
      changes since v4 (v3 was never posted)
      	documentation
      	dropped SKB_ARRAY_MIN_SIZE heuristic
      	unit test (in userspace, included as patch 2)
      
      changes since v2:
              fixed integer overflow pointed out by Eric.
              added some comments.
      
      changes since v1:
              fixed bug pointed out by Eric.
      ====================
      Tested-by: NJesper Dangaard Brouer <brouer@redhat.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      829e64d1
    • M
      skb_array: resize support · 7d7072e3
      Michael S. Tsirkin 提交于
      Update skb_array after ptr_ring API changes.
      Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
      Acked-by: NJesper Dangaard Brouer <brouer@redhat.com>
      Tested-by: NJesper Dangaard Brouer <brouer@redhat.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7d7072e3
    • M
      ptr_ring: resize support · 5d49de53
      Michael S. Tsirkin 提交于
      This adds ring resize support. Seems to be necessary as
      users such as tun allow userspace control over queue size.
      
      If resize is used, this costs us ability to peek at queue without
      consumer lock - should not be a big deal as peek and consumer are
      usually run on the same CPU.
      
      If ring is made bigger, ring contents is preserved.  If ring is made
      smaller, extra pointers are passed to an optional destructor callback.
      
      Cleanup function also gains destructor callback such that
      all pointers in queue can be cleaned up.
      
      This changes some APIs but we don't have any users yet,
      so it won't break bisect.
      Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
      Acked-by: NJesper Dangaard Brouer <brouer@redhat.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5d49de53
    • M
      skb_array: array based FIFO for skbs · ad69f35d
      Michael S. Tsirkin 提交于
      A simple array based FIFO of pointers.  Intended for net stack so uses
      skbs for type safety. Implemented as a set of wrappers around ptr_ring.
      Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
      Acked-by: NJesper Dangaard Brouer <brouer@redhat.com>
      Tested-by: NJesper Dangaard Brouer <brouer@redhat.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ad69f35d
    • M
      ptr_ring: ring test · 9fb6bc5b
      Michael S. Tsirkin 提交于
      Add ringtest based unit test for ptr ring.
      Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      9fb6bc5b
    • M
      ptr_ring: array based FIFO for pointers · 2e0ab8ca
      Michael S. Tsirkin 提交于
      A simple array based FIFO of pointers.  Intended for net stack which
      commonly has a single consumer/producer.
      Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
      Acked-by: NJesper Dangaard Brouer <brouer@redhat.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2e0ab8ca
    • W
      net_sched: make tcf_hash_check() boolean · b2313077
      WANG Cong 提交于
      Cc: Jamal Hadi Salim <jhs@mojatatu.com>
      Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
      Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b2313077
    • D
      Merge branch 'vrf-ipv6-mcast-link-local' · a6e225ca
      David S. Miller 提交于
      David Ahern says:
      
      ====================
      net: vrf: Handle ipv6 multicast and link-local addresses
      
      IPv6 multicast and link-local addresses require special handling by the
      VRF driver. Rather than using the VRF device index and full FIB lookups,
      packets to/from these addresses should use direct FIB lookups based on
      the VRF device table.
      
      Multicast routes do not make sense for the L3 master device directly.
      Accordingly, do not add mcast routes for the device, and the VRF driver
      should fail attempts to send packets to ipv6 mcast addresses on the
      device (e.g, ping6 ff02::1%<vrf> should fail)
      
      With this change connections into and out of a VRF enslaved device work
      for multicast and link-local addresses (icmp, tcp, and udp).  e.g.,
      
      1. packets into VM with VRF config:
          ping6 -c3 fe80::e0:f9ff:fe1c:b974%br1
          ping6 -c3 ff02::1%br1
          ssh -6 fe80::e0:f9ff:fe1c:b974%br1
      
      2. packets going out a VRF enslaved device:
          ping6 -c3 fe80::18f8:83ff:fe4b:7a2e%eth1
          ping6 -c3 ff02::1%eth1
          ssh -6 root@fe80::18f8:83ff:fe4b:7a2e%eth1
      ====================
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a6e225ca
    • D
      net: vrf: Handle ipv6 multicast and link-local addresses · 9ff74384
      David Ahern 提交于
      IPv6 multicast and link-local addresses require special handling by the
      VRF driver:
      1. Rather than using the VRF device index and full FIB lookups,
         packets to/from these addresses should use direct FIB lookups based on
         the VRF device table.
      
      2. fail sends/receives on a VRF device to/from a multicast address
         (e.g, make ping6 ff02::1%<vrf> fail)
      
      3. move the setting of the flow oif to the first dst lookup and revert
         the change in icmpv6_echo_reply made in ca254490 ("net: Add VRF
         support to IPv6 stack"). Linklocal/mcast addresses require use of the
         skb->dev.
      
      With this change connections into and out of a VRF enslaved device work
      for multicast and link-local addresses work (icmp, tcp, and udp)
      e.g.,
      
      1. packets into VM with VRF config:
          ping6 -c3 fe80::e0:f9ff:fe1c:b974%br1
          ping6 -c3 ff02::1%br1
      
          ssh -6 fe80::e0:f9ff:fe1c:b974%br1
      
      2. packets going out a VRF enslaved device:
          ping6 -c3 fe80::18f8:83ff:fe4b:7a2e%eth1
          ping6 -c3 ff02::1%eth1
          ssh -6 root@fe80::18f8:83ff:fe4b:7a2e%eth1
      Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      9ff74384
    • D
      net: ipv6: Do not add multicast route for l3 master devices · ba46ee4c
      David Ahern 提交于
      L3 master devices are virtual devices similar to the loopback
      device. Link local and multicast routes for these devices do
      not make sense. The ipv6 addrconf code already skips adding a
      linklocal address; do the same for the mcast route.
      Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ba46ee4c
    • D
      net: l3mdev: Remove const from flowi6 arg to get_rt6_dst · cd2a9e62
      David Ahern 提交于
      Allow drivers to pass flow arg to functions where the arg is not const
      and allow the driver to make updates as needed (eg., setting oif).
      Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      cd2a9e62
    • D
      Merge branch 'af_iucv-big-bufs' · c9ad5a65
      David S. Miller 提交于
      Ursula Braun says:
      
      ====================
      s390: af_iucv patches
      
      here are improvements for af_iucv relaxing the pressure to allocate
      big contiguous kernel buffers.
      ====================
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c9ad5a65
    • E
      af_iucv: use paged SKBs for big inbound messages · a006353a
      Eugene Crosser 提交于
      When an inbound message is bigger than a page, allocate a paged SKB,
      and subsequently use IUCV receive primitive with IPBUFLST flag.
      This relaxes the pressure to allocate big contiguous kernel buffers.
      Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
      Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a006353a
    • E
      af_iucv: remove fragment_skb() to use paged SKBs · 291759a5
      Eugene Crosser 提交于
      Before introducing paged skbs in the receive path, get rid of the
      function `iucv_fragment_skb()` that replaces one large linear skb
      with several smaller linear skbs.
      Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
      Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      291759a5
    • E
      af_iucv: use paged SKBs for big outbound messages · e5374399
      Eugene Crosser 提交于
      When an outbound message is bigger than a page, allocate and fill
      a paged SKB, and subsequently use IUCV send primitive with IPBUFLST
      flag. This relaxes the pressure to allocate big contiguous kernel
      buffers.
      Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
      Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      e5374399
    • A
      dt: bindings: Add bindings for Cirrus Logic CS89x0 ethernet chip · 818d49ad
      Alexander Shiyan 提交于
      Add device tree binding documentation details for Cirrus Logic
      CS8900/CS8920 ethernet chip.
      Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
      Acked-by: NRob Herring <robh@kernel.org>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      818d49ad
    • A
      net: cx89x0: Add DT support · d3cf8fd3
      Alexander Shiyan 提交于
      Add DT support to the Cirrus Logic CS89x0 driver.
      Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d3cf8fd3
  2. 15 6月, 2016 11 次提交