- 24 1月, 2016 1 次提交
-
-
由 Huacai Chen 提交于
While synchronization, count register will go backwards for the master. If synchronise_count_master() runs before synchronise_count_slave(), skew becomes even more. The skew is very harmful for CPU hotplug (CPU0 do synchronization with CPU1, then CPU0 do synchronization with CPU2 and CPU0's count goes backwards, so it will be out of sync with CPU1). After the commit cf9bfe55 (MIPS: Synchronize MIPS count one CPU at a time), we needn't evaluate count_reference at the beginning of synchronise_count_master() any more. Thus, we evaluate the initcount (It seems like count_reference is redundant) in the 2nd loop. Since we write the count register in the last loop, we don't need additional barriers (the existing memory barriers are enough). Moreover, I think we loop 3 times is enough to get a primed instruction cache, this can also get less skew than looping 5 times. Comments are also updated in this patch. Signed-off-by: NHuacai Chen <chenhc@lemote.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Patchwork: https://patchwork.linux-mips.org/patch/12163/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 22 1月, 2016 4 次提交
-
-
由 Huacai Chen 提交于
This patch is borrowed from x86 hpet driver and explaind below: Due to the overly intelligent design of HPETs, we need to workaround the problem that the compare value which we write is already behind the actual counter value at the point where the value hits the real compare register. This happens for two reasons: 1) We read out the counter, add the delta and write the result to the compare register. When a NMI hits between the read out and the write then the counter can be ahead of the event already. 2) The write to the compare register is delayed by up to two HPET cycles in AMD chipsets. We can work around this by reading back the compare register to make sure that the written value has hit the hardware. But that is bad performance wise for the normal case where the event is far enough in the future. As we already know that the write can be delayed by up to two cycles we can avoid the read back of the compare register completely if we make the decision whether the delta has elapsed already or not based on the following calculation: cmp = event - actual_count; If cmp is less than 64 HPET clock cycles, then we decide that the event has happened already and return -ETIME. That covers the above #1 and #2 problems which would cause a wait for HPET wraparound (~306 seconds). Signed-off-by: NHuacai Chen <chenhc@lemote.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: Huacai Chen <chenhc@lemote.com> Cc: linux-mips@linux-mips.org Cc: stable@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/12162/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Huacai Chen 提交于
When Core-0 handle SMP_ASK_C0COUNT IPI, we should make other cores to see the result as soon as possible (especially when Store-Fill-Buffer is enabled). Otherwise, C0_Count syncronization makes no sense. BTW, array is more suitable than per-cpu variable for syncronization, and there is a corner case should be avoid: C0_Count of Core-0 can be really 0. Signed-off-by: NHuacai Chen <chenhc@lemote.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: Huacai Chen <chenhc@lemote.com> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> Patchwork: https://patchwork.linux-mips.org/patch/12160/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Huacai Chen 提交于
If GCC >= 4.9 and Binutils >=2.25, we use -march=loongson3a, otherwise we use -march=mips64r2, this can slightly improve performance. Besides, arch/mips/loongson64/Platform is a better location rather than arch/ mips/Makefile. Signed-off-by: NHuacai Chen <chenhc@lemote.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/12161/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Huacai Chen 提交于
In history, __arch_local_irq_restore() is only used by SMTC. However, SMTC support has been removed since 3.16, this patch remove the unused function. Signed-off-by: NHuacai Chen <chenhc@lemote.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/12159/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 20 1月, 2016 20 次提交
-
-
由 Maciej W. Rozycki 提交于
Add an `ieee754=' kernel parameter to control IEEE Std 754 conformance mode. Use separate flags copied from the respective CPU feature flags, and adjusted according to the conformance mode selected, to make binaries requesting individual NaN encoding modes accepted or rejected as needed. Update the initial setting for FCSR and, in the full FPU emulation mode, its read-only mask accordingly. Accept the mode selection requested for legacy processors as well. As with the EF_MIPS_NAN2008 ELF file header flag adjust both ABS2008 and NAN2008 bits at the same time, to match the choice made for hardware currently implemented. Signed-off-by: NMaciej W. Rozycki <macro@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Matthew Fortune <Matthew.Fortune@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11481/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Maciej W. Rozycki 提交于
Determine the presence of and the amount of control available over IEEE Std 754-2008 features. In the case of a hardware FPU being used examine the FIR register for the presence of the HAS2008 bit and then the FCSR register for the writability of the ABS2008 and NAN2008 bits and the hardwired state of each of these bits if read-only. Update the initial FCSR contents used for threads and the FCSR writability mask accordingly. For full FPU emulation and MIPS32 or MIPS64 processors make the FCSR ABS2008 and NAN2008 bits writable. Signed-off-by: NMaciej W. Rozycki <macro@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Matthew Fortune <Matthew.Fortune@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11480/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Maciej W. Rozycki 提交于
Handle the EF_MIPS_NAN2008 ELF file header flag and refuse execution where there is no support in the FPU for the NaN encoding mode requested by a binary invoked. Ensure that the setting of the bit in the binary matches one in any intepreter used. Set the thread's initial FCSR contents according to the value of the EF_MIPS_NAN2008. Set the values of the FCSR ABS2008 and NAN2008 bits both to the same value if possible, to take the approach taken with existing FPU hardware into account. As of now all implementations have both bits hardwired to the same value, that is both are fixed at 0 or both are fixed at 1, even though the architecture allows for implementations where the amount of control implemented with each of these two individual bits is independent of each other. Signed-off-by: NMaciej W. Rozycki <macro@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Matthew Fortune <Matthew.Fortune@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11479/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Maciej W. Rozycki 提交于
Also pass any interpreter's file header to `arch_check_elf' so that any architecture handler can have a look at it if needed. Signed-off-by: NMaciej W. Rozycki <macro@imgtec.com> Acked-by: NAndrew Morton <akpm@linux-foundation.org> Acked-by: NAl Viro <viro@zeniv.linux.org.uk> Cc: Matthew Fortune <Matthew.Fortune@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11478/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Maciej W. Rozycki 提交于
Implement IEEE Std 754-2008 NaN encoding wired to the state of the FCSR.NAN2008 bit. Make the interpretation of the quiet bit in NaN data as follows: * in the legacy mode originally defined by the MIPS architecture the value of 1 denotes an sNaN whereas the value of 0 denotes a qNaN, * in the 2008 mode introduced with revision 5 of the MIPS architecture the value of 0 denotes an sNaN whereas the value of 1 denotes a qNaN, following the definition of the preferred NaN encoding introduced with IEEE Std 754-2008. In the 2008 mode, following the requirement of the said standard, quiet an sNaN where needed by setting the quiet bit to 1 and leaving all the NaN payload bits unchanged. Update format conversion operations according to the rules set by IEEE Std 754-2008 and the MIPS architecture. Specifically: * propagate NaN payload bits through conversions between floating-point formats such that as much information as possible is preserved and specifically a conversion from a narrower format to a wider format and then back to the original format does not change a qNaN payload in any way, * conversions from a floating-point to an integer format where the source is a NaN, infinity or a value that would convert to an integer outside the range of the result format produce, under the default exception handling, the respective values defined by the MIPS architecture. In full FPU emulation set the FIR.HAS2008 bit to 1, however do not make any further FCSR bits writable. Signed-off-by: NMaciej W. Rozycki <macro@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Matthew Fortune <Matthew.Fortune@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11477/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Maciej W. Rozycki 提交于
Implement IEEE Std 754-2008 non-arithmetic ABS.fmt and NEG.fmt emulation wired to the state of the FCSR.ABS2008 bit. In the non-arithmetic mode the sign bit is altered according to the operation requested regardless of the datum encoded in the input operand, no other bits are changed, the resulting bit pattern is written to the output operand and no exception is ever signalled. Signed-off-by: NMaciej W. Rozycki <macro@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Matthew Fortune <Matthew.Fortune@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11476/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Maciej W. Rozycki 提交于
Allocate CPU option bits and define macros for the legacy-NaN and 2008-NaN IEEE Std 754 MIPS architecture features. Unconditionally mark the legacy-NaN feature as present across hardware and emulated floating-point configurations. Signed-off-by: NMaciej W. Rozycki <macro@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Matthew Fortune <Matthew.Fortune@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11475/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Maciej W. Rozycki 提交于
Rewrite `arch_elf_pt_proc' and `arch_check_elf' using a union to access the ELF file header. Signed-off-by: NMaciej W. Rozycki <macro@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Matthew Fortune <Matthew.Fortune@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11474/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 John Crispin 提交于
Signed-off-by: NJohn Crispin <blogic@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/11998/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 John Crispin 提交于
Signed-off-by: NJohn Crispin <blogic@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/11997/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 John Crispin 提交于
The "a" version of the MT7620 has single port PCIE bus. The driver is straightforward without any special magic required. The driver works on MT7620 and MT7628. There are a few magic values that get written to the pcie phy and a register of which we only know the name. I marked these places as vodoo in the comments above the code. Signed-off-by: NJohn Crispin <blogic@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/11996/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 John Crispin 提交于
Signed-off-by: NJohn Crispin <blogic@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/11995/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 John Crispin 提交于
Ralink was acquired by Mediatek. Represent this in the cpuinfo. It apparently confused people. Signed-off-by: NJohn Crispin <blogic@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/11994/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 John Crispin 提交于
Commit 418d29c8 ("MIPS: ralink: Unify SoC id handling") introduced broken code. We obviously need to assign the value. Signed-off-by: NJohn Crispin <blogic@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/11993/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 John Crispin 提交于
Commit 418d29c8 ("MIPS: ralink: Unify SoC id handling") was not fully correct. The logic for the SoC check got inverted. We need to check if it is not a MT76x8. Signed-off-by: NJohn Crispin <blogic@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/11992/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 John Crispin 提交于
A few fixes to the pinmux data, 2 new muxes and a minor whitespace cleanup. Signed-off-by: NJohn Crispin <blogic@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/11991/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 John Crispin 提交于
MT7621 is based on a 1004k core. This patch adds support for the SoC. The timer and IRQ is just boiler plate as GIC has recently been moved to generic places in the kernel and just works. Signed-off-by: NJohn Crispin <blogic@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/11990/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 John Crispin 提交于
Some of the newer SoCs use the GIC. This patch splits the INTC out into its own symbol, allowing us to add the gic code in the following patch. Signed-off-by: NJohn Crispin <blogic@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/11989/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 John Crispin 提交于
Add three files. ralink,rt2880-net.txt descibes the actual frame engine and the other two describe the switch forntend bindings. Signed-off-by: NJohn Crispin <blogic@openwrt.org> Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NMichael Lee <igvtee@gmail.com> Cc: devicetree@vger.kernel.org Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-mediatek@lists.infradead.org Cc: John Crispin <blogic@openwrt.org> Cc: Felix Fietkau <nbd@nbd.name> Cc: Michael Lee <igvtee@gmail.com> Cc: steven.liu@mediatek.com Cc: Fred.Chang@mediatek.com Patchwork: https://patchwork.linux-mips.org/patch/11970/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Rafał Miłecki 提交于
BCM47XX platform has specific PCI setup because all buses share the same domain. It's different e.g. on ARM ARCH_BCM_5301X where each PCI bus gets its own domain (they are handled by iProc PCIe controller driver). As we want to make SPROM driver more generic, let's add an exception for BCM47xx. It was tested on BCM4706 (MIPS) and BCM4708A0 (ARM). Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/11969/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 04 1月, 2016 12 次提交
-
-
由 Alex Smith 提交于
Add device tree nodes for the NEMC and BCH to the JZ4780 device tree, and make use of them in the Ci20 device tree to add a node for the board's NAND. Note that since the pinctrl driver is not yet upstream, this includes neither pin configuration nor busy/write-protect GPIO pins for the NAND. Use of the NAND relies on the boot loader to have left the pins configured in a usable state, which should be the case when booted from the NAND. [ralf@linux-mips.org: fold in Geert Uytterhoeven's patch and acks from Harvey's latest version.] Signed-off-by: NAlex Smith <alex.smith@imgtec.com> Signed-off-by: NHarvey Hunt <harvey.hunt@imgtec.com> Reviewed-by: NBoris Brezillon <boris.brezillon@free-electrons.com> Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Alex Smith <alex.smith@imgtec.com> Cc: linux-mtd@lists.infradead.org Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-mtd@lists.infradead.org Patchwork: https://patchwork.linux-mips.org/patch/11695/ Patchwork: https://patchwork.linux-mips.org/patch/11914/ Patchwork: https://patchwork.linux-mips.org/patch/11985/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Simon Arlott 提交于
The BCM63168 requires the same CPU1 fix as BCM6368. Signed-off-by: NSimon Arlott <simon@fire.lp0.eu> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: linux-mips@linux-mips.org Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org> Patchwork: https://patchwork.linux-mips.org/patch/11487/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Alban Bedel 提交于
Remove the unused defines for the reference clocks rate and the useless machine init function. Signed-off-by: NAlban Bedel <albeu@free.fr> Cc: Felix Fietkau <nbd@openwrt.org> Cc: Qais Yousef <qais.yousef@imgtec.com> Cc: Andrew Bresticker <abrestic@chromium.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11505/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Alban Bedel 提交于
Move the declaration of ath79_ddr_wb_flush() to asm/mach-ath79/ath79.h to allow using it from drivers. This is needed to move the CPU IRQ driver to drivers/irqchip. Signed-off-by: NAlban Bedel <albeu@free.fr> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Alexander Couzens <lynxis@fe80.eu> Cc: Joel Porquet <joel@porquet.org> Cc: Andrew Bresticker <abrestic@chromium.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11502/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Alban Bedel 提交于
To prepare moving out of the arch directory rework the MISC implementation to use irq domains instead of hard coded IRQ numbers. Also remove the uses of the ath79_reset_base global pointer in the IRQ methods. Signed-off-by: NAlban Bedel <albeu@free.fr> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Alexander Couzens <lynxis@fe80.eu> Cc: Joel Porquet <joel@porquet.org> Cc: Andrew Bresticker <abrestic@chromium.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11506/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Alban Bedel 提交于
IRQCHIP is always enabled, so the #ifdef can just be removed. Signed-off-by: NAlban Bedel <albeu@free.fr> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Alexander Couzens <lynxis@fe80.eu> Cc: Joel Porquet <joel@porquet.org> Cc: Andrew Bresticker <abrestic@chromium.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11504/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Alban Bedel 提交于
Signed-off-by: NAlban Bedel <albeu@free.fr> Cc: linux-mips@linux-mips.org Cc: Rob Herring <robh+dt@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11499/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Alban Bedel 提交于
Signed-off-by: NAlban Bedel <albeu@free.fr> Cc: Rob Herring <robh+dt@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: linux-mips@linux-mips.org Cc: devicetree@vger.kernel.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11498/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Alban Bedel 提交于
Signed-off-by: NAlban Bedel <albeu@free.fr> Acked-by: NRob Herring <robh@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: devicetree@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11496/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Linus Torvalds 提交于
-
git://git.linux-mips.org/pub/scm/ralf/upstream-linus由 Linus Torvalds 提交于
Pull MIPS build fix from Ralf Baechle: "Fix a makefile issue resulting in build breakage with older binutils. This has sat in -next for a few days, testers and buildbot are happy with it, too though if you are going for another -rc that'd certainly help ironing out a few more issues" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: MIPS: VDSO: Fix build error with binutils 2.24 and earlier
-
git://anongit.freedesktop.org/drm-intel由 Linus Torvalds 提交于
Pull i915 drm fixes from Jani Nikula: "Two display fixes still for v4.4. The new year's resolution is to start using signed tags per Linus' request. This one is still unsigned; I want to fix this up in our maintainer scripts instead of doing it one-off" * tag 'drm-intel-fixes-2016-01-02' of git://anongit.freedesktop.org/drm-intel: drm/i915: increase the tries for HDMI hotplug live status checking drm/i915: Unbreak check_digital_port_conflicts()
-
- 01 1月, 2016 3 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci由 Linus Torvalds 提交于
Pull PCI bugfix from Bjorn Helgaas: "Here's another fix for v4.4. This fixes 32-bit config reads for the HiSilicon driver. Obviously the driver is completely broken without this fix (apparently it actually was tested internally, but got broken somehow in the process of upstreaming it). Summary: HiSilicon host bridge driver Fix 32-bit config reads (Dongdong Liu)" * tag 'pci-v4.4-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI: hisi: Fix hisi_pcie_cfg_read() 32-bit reads
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc由 Linus Torvalds 提交于
Pull sparc fixes from David Miller: "Just some missing syscall wire ups" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc: sparc: Wire up mlock2 system call. sparc: Add all necessary direct socket system calls.
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net由 Linus Torvalds 提交于
Pull networking fixes from David Miller: 1) Prevent XFRM per-cpu counter updates for one namespace from being applied to another namespace. Fix from DanS treetman. 2) Fix RCU de-reference in iwl_mvm_get_key_sta_id(), from Johannes Berg. 3) Remove ethernet header assumption in nft_do_chain_netdev(), from Pablo Neira Ayuso. 4) Fix cpsw PHY ident with multiple slaves and fixed-phy, from Pascal Speck. 5) Fix use after free in sixpack_close and mkiss_close. 6) Fix VXLAN fw assertion on bnx2x, from Yuval Mintz. 7) natsemi doesn't check for DMA mapping errors, from Alexey Khoroshilov. 8) Fix inverted test in ip6addrlbl_get(), from ANdrey Ryabinin. 9) Missing initialization of needed_headroom in geneve tunnel driver, from Paolo Abeni. 10) Fix conntrack template leak in openvswitch, from Joe Stringer. 11) Mission initialization of wq->flags in sock_alloc_inode(), from Nicolai Stange. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits) sctp: sctp should release assoc when sctp_make_abort_user return NULL in sctp_close net, socket, socket_wq: fix missing initialization of flags drivers: net: cpsw: fix error return code openvswitch: Fix template leak in error cases. sctp: label accepted/peeled off sockets sctp: use GFP_USER for user-controlled kmalloc qlcnic: fix a loop exit condition better net: cdc_ncm: avoid changing RX/TX buffers on MTU changes geneve: initialize needed_headroom ipv6: honor ifindex in case we receive ll addresses in router advertisements addrconf: always initialize sysctl table data ipv6/addrlabel: fix ip6addrlbl_get() switchdev: bridge: Pass ageing time as clock_t instead of jiffies sh_eth: fix 16-bit descriptor field access endianness too veth: don’t modify ip_summed; doing so treats packets with bad checksums as good. net: usb: cdc_ncm: Adding Dell DW5813 LTE AT&T Mobile Broadband Card net: usb: cdc_ncm: Adding Dell DW5812 LTE Verizon Mobile Broadband Card natsemi: add checks for dma mapping errors rhashtable: Kill harmless RCU warning in rhashtable_walk_init openvswitch: correct encoding of set tunnel action attributes ...
-