The return value of function macvlan_addr_busy is used as bool value,
so use bool value instead of integer number "1" and "0".
Signed-off-by: NGao Feng <gfree.wind@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there is no existing macvlan port in lowdev, one new macvlan port
would be created. But it doesn't be destoried when something failed later.
It casues some memleak.

Now add one flag to indicate if new macvlan port is created.
Signed-off-by: NGao Feng <fgao@ikuai8.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

geneve:
- Merge __geneve_change_mtu back into geneve_change_mtu, set max_mtu
- This one isn't quite as straight-forward as others, could use some
  closer inspection and testing

macvlan:
- set min/max_mtu

tun:
- set min/max_mtu, remove tun_net_change_mtu

vxlan:
- Merge __vxlan_change_mtu back into vxlan_change_mtu
- Set max_mtu to IP_MAX_MTU and retain dynamic MTU range checks in
  change_mtu function
- This one is also not as straight-forward and could use closer inspection
  and testing from vxlan folks

bridge:
- set max_mtu of IP_MAX_MTU and retain dynamic MTU range checks in
  change_mtu function

openvswitch:
- set min/max_mtu, remove internal_dev_change_mtu
- note: max_mtu wasn't checked previously, it's been set to 65535, which
  is the largest possible size supported

sch_teql:
- set min/max_mtu (note: max_mtu previously unchecked, used max of 65535)

macsec:
- min_mtu = 0, max_mtu = 65535

macvlan:
- min_mtu = 0, max_mtu = 65535

ntb_netdev:
- min_mtu = 0, max_mtu = 65535

veth:
- min_mtu = 68, max_mtu = 65535

8021q:
- min_mtu = 0, max_mtu = 65535

CC: netdev@vger.kernel.org
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
CC: Tom Herbert <tom@herbertland.com>
CC: Daniel Borkmann <daniel@iogearbox.net>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Paolo Abeni <pabeni@redhat.com>
CC: Jiri Benc <jbenc@redhat.com>
CC: WANG Cong <xiyou.wangcong@gmail.com>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Pravin B Shelar <pshelar@ovn.org>
CC: Sabrina Dubroca <sd@queasysnail.net>
CC: Patrick McHardy <kaber@trash.net>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: Pravin Shelar <pshelar@nicira.com>
CC: Maxim Krasnyansky <maxk@qti.qualcomm.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The idea for type_check in dev_get_nest_level() was to count the number
of nested devices of the same type (currently, only macvlan or vlan
devices).
This prevented the false positive lockdep warning on configurations such
as:

eth0 <--- macvlan0 <--- vlan0 <--- macvlan1

However, this doesn't prevent a warning on a configuration such as:

eth0 <--- macvlan0 <--- vlan0
eth1 <--- vlan1 <--- macvlan1

In this case, all the locks end up with a nesting subclass of 1, so
lockdep thinks that there is still a deadlock:

- in the first case we have (macvlan_netdev_addr_lock_key, 1) and then
  take (vlan_netdev_xmit_lock_key, 1)
- in the second case, we have (vlan_netdev_xmit_lock_key, 1) and then
  take (macvlan_netdev_addr_lock_key, 1)

By removing the linktype check in dev_get_nest_level() and always
incrementing the nesting depth, lockdep considers this configuration
valid.
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case a qdisc is used on a macvlan device, we need to use different
lockdep classes to avoid false positives.

Use the new netdev_lockdep_set_classes() generic helper.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we always queue a multicast packet for further processing,
even if none of the macvlan devices are subscribed to the address.

This patch optimises this by adding a global multicast filter for
a macvlan_port.

Note that this patch doesn't handle the broadcast addresses of the
individual macvlan devices correctly, if they are not all identical
to vlan->lowerdev.  However, this is already broken because there
is no mechanism in place to update the individual multicast filters
when you change the broadcast address.

If someone cares enough they should fix this by collecting all
broadcast addresses for a macvlan as we do for multicast and unicast.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we postpone a broadcast packet we save the source port in
the skb if it is local.  However, the source port can disappear
before we get a chance to process the packet.

This patch fixes this by holding a ref count on the netdev.

It also delays the skb->cb modification until after we allocate
the new skb as you should not modify shared skbs.

Fixes: 412ca155 ("macvlan: Move broadcasts into a work queue")
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If macvlan_common_newlink fails in register_netdevice after macvlan_init
then it decrements port->count twice, first in macvlan_uninit (from
register_netdevice or rollback_registered) and then again in
macvlan_common_newlink.
A similar problem may exist in the ipvlan driver.
This patch consolidates modifications to port->count into macvlan_init
and macvlan_uninit (thanks to Eric Biederman for suggesting this approach).

v3: remove macvtap specific bits.
Signed-off-by: NFrancesco Ruggeri <fruggeri@arista.com>
Acked-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vlan drivers lack proper propagation of gso_max_segs from
lower device.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid Decotigny <decot@googlers.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use IFF_NO_QUEUE to indicate that a device can run without a qdisc.
Signed-off-by: NZhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when a macvlan is being initialized and the lower device is
netif_carrier_ok(), the macvlan device doesn't run through
rfc2863_policy() and is left with UNKNOWN operstate. Fix it by adding an
unconditional linkwatch event for the new macvlan device. Similar fix is
already used by the 8021q device (see register_vlan_dev()). Also fix the
inconsistent state when the lower device has been down and its carrier
was changed (when a device is down NETDEV_CHANGE doesn't get generated).
The second issue can be seen f.e. when we have a macvlan on top of a 8021q
device which has been down and its real device has been changing carrier
states, after setting the 8021q device up, the macvlan device will have
the same carrier state as it was before even though the 8021q can now
have a different state.
Example for case 1:
4: eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UP mode DEFAULT group default qlen 1000

$ ip l add l eth2 macvl0 type macvlan
$ ip l set macvl0 up
$ ip l sh macvl0
72: macvl0@eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc
noqueue state UNKNOWN mode DEFAULT group default
    link/ether f6:0b:54:0a:9d:a3 brd ff:ff:ff:ff:ff:ff

Example for case 2 (order is important):
Prestate: eth2 UP/CARRIER, vlan1 down, vlan1-macvlan down
$ ip l set vlan1-macvlan up
$ ip l sh vlan1-macvlan
71: vlan1-macvlan@vlan1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500
qdisc noqueue state UNKNOWN mode DEFAULT group default
    link/ether 4a:b8:44:56:b9:b9 brd ff:ff:ff:ff:ff:ff

[ eth2 loses CARRIER before vlan1 has been UP-ed ]

$ ip l sh eth2
4: eth2: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast
state DOWN mode DEFAULT group default qlen 1000
    link/ether 52:54:00:bf:57:16 brd ff:ff:ff:ff:ff:ff
$ ip l sh vlan1-macvlan
71: vlan1-macvlan@vlan1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500
qdisc noqueue state UNKNOWN mode DEFAULT group default
    link/ether 4a:b8:44:56:b9:b9 brd ff:ff:ff:ff:ff:ff
$ ip l set vlan1 up
$ ip l sh vlan1
70: vlan1@eth2: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc
noqueue state LOWERLAYERDOWN mode DEFAULT group default qlen 1000
    link/ether 52:54:00:bf:57:16 brd ff:ff:ff:ff:ff:ff
$ ip l sh vlan1-macvlan
71: vlan1-macvlan@vlan1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500
qdisc noqueue state UNKNOWN mode DEFAULT group default
    link/ether 4a:b8:44:56:b9:b9 brd ff:ff:ff:ff:ff:ff

vlan1-macvlan is still UP, still has carrier and is still in the same
operstate as before. After the patch in case 1 macvl0 has state UP as it
should and in case 2 vlan1-macvlan has state LOWERLAYERDOWN again as it
should. Note that while the lower macvlan device is down their carrier
and thus operstate can go out of sync but that will be fixed once the
lower device goes up again.
This behaviour seems to have been present since beginning of git history.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These netif flags are unnecessary convolutions. It is more
straightforward to just use NETIF_F_HW_CSUM, NETIF_F_IP_CSUM,
and NETIF_F_IPV6_CSUM directly.

This patch also:
    - Cleans up can_checksum_protocol
    - Simplifies netdev_intersect_features
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.

This patch:
  - Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
    NETIF_F_ALL_CSUM is being used as a mask).
  - Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
    use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reset pskb in macvlan_handle_frame in case skb_share_check returned a
clone.

Fixes: 8a4eb573 ("net: introduce rx_handler results and logic around that")
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function ip_defrag is called on both the input and the output
paths of the networking stack.  In particular conntrack when it is
tracking outbound packets from the local machine calls ip_defrag.

So add a struct net parameter and stop making ip_defrag guess which
network namespace it needs to defragment packets in.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Macvlan/macvtap devices don't need to segment multiple tagged packets
since the lower devices can segment them.
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a macvlan device is placed in promiscuous mode, it currently
just sets it's multicast mask to permissive, but doesn't change
the state of the lower device.  As a result, not all multicast
traffic can be received on such device.  Additionally, none of
a vlan traffic can be received on such device as well.
This patch propagates the promiscuous mode setting to lower device
so that lower device may receive all packets that macvlan may
be interested in.
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't use dev->iflink anymore.

CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that there are no more users kill dev_rebuild_header and all of it's
implementations.

This is long overdue.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Assign rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is
added to rtnetlink messages.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If device is already used as an ipvlan port then refuse to
use it as a macvlan port at early stage of port creation.

	thost1:~# ip link add link eth0 ipvl0 type ipvlan
	thost1:~# echo $?
	0
	thost1:~# ip link add link eth0 mvl0 type macvlan
	RTNETLINK answers: Device or resource busy
	thost1:~# echo $?
	2
	thost1:~#
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit fbe168ba ("net: generic dev_disable_lro() stacked
device handling"), dev_disable_lro() zeroes NETIF_F_LRO feature flag
first for a macvlan device and then for its lower device. As an attempt
to set NETIF_F_LRO to zero is ignored, dev_disable_lro() issues a
warning and taints kernel.

Allowing NETIF_F_LRO to be set independently of the lower device
consists of three parts:

  - add the flag to hw_features to allow toggling it
  - allow setting it to 0 even if lower device has the flag set
  - add the flag to MACVLAN_FEATURES to restore copying from lower
    device on macvlan creation
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We do header check twice for a dodgy packet. One is done before
macvlan_start_xmit(), another is done before lower device's
ndo_start_xmit(). The first one seems redundant so this patch tries to
delay header check until a packet reaches its lower device (or macvtap)
through always enabling NETIF_F_GSO_ROBUST for macvlan device.

Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to cancel the work queue after rcu grace period,
otherwise it can be rescheduled by incoming packets.

We need to purge queue if some skbs are still in it.

We can use __skb_queue_head_init() variant in
macvlan_process_broadcast()
Signed-off-by: NEric Dumazet <edumazet@google.com>
Fixes: 412ca155 ("macvlan: Move broadcasts into a work queue")
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netif_rx() call on the fast path of macvlan_handle_frame() appears to
be there to ensure that we properly throttle incoming packets. However, it
would appear as though the proper throttling is already in place for all
possible ingress paths, and that the call is redundant. If packets are arriving
from the physical NIC, we've already throttled them by this point. Otherwise,
if they are coming via macvlan_queue_xmit(), it calls either
'dev_forward_skb()', which ends up calling netif_rx_internal(), or else in
the broadcast case, we are throttling via macvlan_broadcast_enqueue().

The test results below are from off the box to an lxc instance running macvlan.
Once the tranactions/sec stop increasing, the cpu idle time has gone to 0.
Results are from a quad core Intel E3-1270 V2@3.50GHz box with bnx2x 10G card.

for i in {10,100,200,300,400,500};
do super_netperf $i -H $ip -t TCP_RR; done
Average of 5 runs.

trans/sec 		 trans/sec
(3.17-rc7-net-next)      (3.17-rc7-net-next + this patch)
----------               ----------
208101                   211534 (+1.6%)
839493                   850162 (+1.3%)
845071                   844053 (-.12%)
816330                   819623 (+.4%)
778700                   789938 (+1.4%)
735984                   754408 (+2.5%)
Signed-off-by: NJason Baron <jbaron@akamai.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass last argument to macvlan_count_rx() as the correct bool type.
Signed-off-by: NJason Baron <jbaron@akamai.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Testing xmit_more support with netperf and connected UDP sockets,
I found strange dst refcount false sharing.

Current handling of IFF_XMIT_DST_RELEASE is not optimal.

Dropping dst in validate_xmit_skb() is certainly too late in case
packet was queued by cpu X but dequeued by cpu Y

The logical point to take care of drop/force is in __dev_queue_xmit()
before even taking qdisc lock.

As Julian Anastasov pointed out, need for skb_dst() might come from some
packet schedulers or classifiers.

This patch adds new helper to cleanly express needs of various drivers
or qdiscs/classifiers.

Drivers that need skb_dst() in their ndo_start_xmit() should call
following helper in their setup instead of the prior :

	dev->priv_flags &= ~IFF_XMIT_DST_RELEASE;
->
	netif_keep_dst(dev);

Instead of using a single bit, we use two bits, one being
eventually rebuilt in bonding/team drivers.

The other one, is permanent and blocks IFF_XMIT_DST_RELEASE being
rebuilt in bonding/team. Eventually, we could add something
smarter later.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new mode of operation to macvlan, called "source".
It allows one to set a list of allowed mac address, which is used
to match against source mac address from received frames on underlying
interface.
This enables creating mac based VLAN associations, instead of standard
port or tag based. The feature is useful to deploy 802.1x mac based
behavior, where drivers of underlying interfaces doesn't allows that.

Configuration is done through the netlink interface using e.g.:
 ip link add link eth0 name macvlan0 type macvlan mode source
 ip link add link eth0 name macvlan1 type macvlan mode source
 ip link set link dev macvlan0 type macvlan macaddr add 00:11:11:11:11:11
 ip link set link dev macvlan0 type macvlan macaddr add 00:22:22:22:22:22
 ip link set link dev macvlan0 type macvlan macaddr add 00:33:33:33:33:33
 ip link set link dev macvlan1 type macvlan macaddr add 00:33:33:33:33:33
 ip link set link dev macvlan1 type macvlan macaddr add 00:44:44:44:44:44

This allows clients with MAC addresses 00:11:11:11:11:11,
00:22:22:22:22:22 to be part of only VLAN associated with macvlan0
interface. Clients with MAC addresses 00:44:44:44:44:44 with only VLAN
associated with macvlan1 interface. And client with MAC address
00:33:33:33:33:33 to be associated with both VLANs.

Based on work of Stefan Gula <steweg@gmail.com>

v8: last version of Stefan Gula for Kernel 3.2.1
v9: rework onto linux-next 2014-03-12 by Michael Braun
    add MACADDR_SET command, enable to configure mac for source mode
    while creating interface
v10:
  - reduce indention level
  - rename source_list to source_entry
  - use aligned 64bit ether address
  - use hash_64 instead of addr[5]
v11:
  - rebase for 3.14 / linux-next 20.04.2014
v12
  - rebase for linux-next 2014-09-25
Signed-off-by: NMichael Braun <michael-dev@fami-braun.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 412ca155 ("macvlan: Move broadcasts into a work queue"), the
driver uses tx_queue_len of the master device as the limit of packets enqueuing.
Problem is that virtual drivers have this value set to 0, thus all broadcast
packets were rejected.
Because tx_queue_len was arbitrarily chosen, I replace it with a static limit
of 1000 (also arbitrarily chosen).

CC: Herbert Xu <herbert@gondor.apana.org.au>
Reported-by: NThibaut Collet <thibaut.collet@6wind.com>
Suggested-by: NThibaut Collet <thibaut.collet@6wind.com>
Tested-by: NThibaut Collet <thibaut.collet@6wind.com>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I cannot move a macvlan interface created on top of a bonding interface
to a different namespace:

% ip netns add dummy0
% ip link add link bond0 mac0 type macvlan
% ip link set mac0 netns dummy0
RTNETLINK answers: Invalid argument
%

The problem seems to be that commit f9399814 ("bonding: Don't allow
bond devices to change network namespaces.") sets NETIF_F_NETNS_LOCAL
on bonding interfaces, and commit 797f87f8 ("macvlan: fix netdev
feature propagation from lower device") causes macvlan interfaces
to inherit its features from the lower device.

NETIF_F_NETNS_LOCAL should not be inherited from the lower device
by a macvlan.
Patch tested on 3.16.
Signed-off-by: NFrancesco Ruggeri <fruggeri@arista.com>
Acked-by: NCong Wang <cwang@twopensource.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, macvlan code restricts multicast and unicast
filter setting only to passthru devices.  As a result,
if a guest using macvtap wants to receive multicast
traffic, it has to set IFF_ALLMULTI or IFF_PROMISC.

This patch makes it possible to use the fdb interface
to add multicast addresses to the filter thus allowing
a guest to receive only targeted multicast traffic.

CC: John Fastabend <john.r.fastabend@intel.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit a188a54d.

It causes crashes

====================
[   80.643286] BUG: unable to handle kernel NULL pointer dereference at 0000000000000878
[   80.670103] IP: [<ffffffff810832e4>] try_to_grab_pending+0x64/0x1f0
[   80.691289] PGD 22c102067 PUD 235bf0067 PMD 0
[   80.706611] Oops: 0002 [#1] SMP
[   80.717836] Modules linked in: macvlan nfsd lockd nfs_acl exportfs auth_rpcgss sunrpc oid_registry ioatdma ixgbe(-) mdio igb dca
[   80.757935] CPU: 37 PID: 6724 Comm: rmmod Not tainted 3.16.0-net-next-08-12-2014-FCoE+ #1
[   80.785688] Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.03.0003.041920141333 04/19/2014
[   80.820310] task: ffff880235a9eae0 ti: ffff88022e844000 task.ti: ffff88022e844000
[   80.845770] RIP: 0010:[<ffffffff810832e4>]  [<ffffffff810832e4>] try_to_grab_pending+0x64/0x1f0
[   80.875326] RSP: 0018:ffff88022e847b28  EFLAGS: 00010046
[   80.893251] RAX: 0000000000037a6a RBX: 0000000000000878 RCX: 0000000000000000
[   80.917187] RDX: ffff880235a9eae0 RSI: 0000000000000001 RDI: ffffffff810832db
[   80.941125] RBP: ffff88022e847b58 R08: 0000000000000000 R09: 0000000000000000
[   80.965056] R10: 0000000000000001 R11: 0000000000000001 R12: ffff88022e847b70
[   80.988994] R13: 0000000000000000 R14: ffff88022e847be8 R15: ffffffff81ebe440
[   81.012929] FS:  00007fab90b07700(0000) GS:ffff88043f7a0000(0000) knlGS:0000000000000000
[   81.040400] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   81.059757] CR2: 0000000000000878 CR3: 0000000235a42000 CR4: 00000000001407e0
[   81.083689] Stack:
[   81.090739]  ffff880235a9eae0 0000000000000878 ffff88022e847b70 0000000000000000
[   81.116253]  ffff88022e847be8 ffffffff81ebe440 ffff88022e847b98 ffffffff810847f1
[   81.141766]  ffff88022e847b78 0000000000000286 ffff880234200000 0000000000000000
[   81.167282] Call Trace:
[   81.175768]  [<ffffffff810847f1>] __cancel_work_timer+0x31/0x170
[   81.195985]  [<ffffffff8108494b>] cancel_work_sync+0xb/0x10
[   81.214769]  [<ffffffffa015ae68>] macvlan_port_destroy+0x28/0x60 [macvlan]
[   81.237844]  [<ffffffffa015b930>] macvlan_uninit+0x40/0x50 [macvlan]
[   81.259209]  [<ffffffff816bf6e2>] rollback_registered_many+0x1a2/0x2c0
[   81.281140]  [<ffffffff816bf81a>] unregister_netdevice_many+0x1a/0xb0
[   81.302786]  [<ffffffffa015a4ff>] macvlan_device_event+0x1ef/0x240 [macvlan]
[   81.326439]  [<ffffffff8108a13d>] notifier_call_chain+0x4d/0x70
[   81.346366]  [<ffffffff8108a201>] raw_notifier_call_chain+0x11/0x20
[   81.367439]  [<ffffffff816bf25b>] call_netdevice_notifiers_info+0x3b/0x70
[   81.390228]  [<ffffffff816bf2a1>] call_netdevice_notifiers+0x11/0x20
[   81.411587]  [<ffffffff816bf6bd>] rollback_registered_many+0x17d/0x2c0
[   81.433518]  [<ffffffff816bf925>] unregister_netdevice_queue+0x75/0x110
[   81.455735]  [<ffffffff816bfb2b>] unregister_netdev+0x1b/0x30
[   81.475094]  [<ffffffffa0039b50>] ixgbe_remove+0x170/0x1d0 [ixgbe]
[   81.495886]  [<ffffffff813512a2>] pci_device_remove+0x32/0x60
[   81.515246]  [<ffffffff814c75c4>] __device_release_driver+0x64/0xd0
[   81.536321]  [<ffffffff814c76f8>] driver_detach+0xc8/0xd0
[   81.554530]  [<ffffffff814c656e>] bus_remove_driver+0x4e/0xa0
[   81.573888]  [<ffffffff814c828b>] driver_unregister+0x2b/0x60
[   81.593246]  [<ffffffff8135143e>] pci_unregister_driver+0x1e/0xa0
[   81.613749]  [<ffffffffa005db18>] ixgbe_exit_module+0x1c/0x2e [ixgbe]
[   81.635401]  [<ffffffff810e738b>] SyS_delete_module+0x15b/0x1e0
[   81.655334]  [<ffffffff8187a395>] ? sysret_check+0x22/0x5d
[   81.673833]  [<ffffffff810abd2d>] ? trace_hardirqs_on_caller+0x11d/0x1e0
[   81.696339]  [<ffffffff8132bfde>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[   81.717985]  [<ffffffff8187a369>] system_call_fastpath+0x16/0x1b
[   81.738199] Code: 00 48 83 3d 6e bb da 00 00 48 89 c2 0f 84 67 01 00 00 fa 66 0f 1f 44 00 00 49 89 14 24 e8 b5 4b 02 00 45 84 ed 0f 85 ac 00 00 00 <f0> 0f ba 2b 00 72 1d 31 c0 48 8b 5d d8 4c 8b 65 e0 4c 8b 6d e8
[   81.807026] RIP  [<ffffffff810832e4>] try_to_grab_pending+0x64/0x1f0
[   81.828468]  RSP <ffff88022e847b28>
[   81.840384] CR2: 0000000000000878
[   81.851731] ---[ end trace 9f6c7232e3464e11 ]---
====================

This bug could be triggered by these steps:

modprobe ixgbe ; modprobe macvlan
ip link add link p96p1 address 00:1B:21:6E:06:00 macvlan0 type macvlan
ip link add link p96p1 address 00:1B:21:6E:06:01 macvlan1 type macvlan
ip link add link p96p1 address 00:1B:21:6E:06:02 macvlan2 type macvlan
ip link add link p96p1 address 00:1B:21:6E:06:03 macvlan3 type macvlan
rmmod ixgbe
Reported-by: N"Keller, Jacob E" <jacob.e.keller@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Macvlan devices do not initialize vlan_features.  As a result,
any vlan devices configured on top of macvlans perform very poorly.
Initialize vlan_features based on the vlan features of the lower-level
device.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

unregister_netdevice_many() API is error prone and we had too
many bugs because of dangling LIST_HEAD on stacks.

See commit f87e6f47 ("net: dont leave active on stack LIST_HEAD")

In fact, instead of making sure no caller leaves an active list_head,
just force a list_del() in the callee. No one seems to need to access
the list after unregister_netdevice_many()
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bonding and team drivers generate specific events during failover
that trigger switch updates.  When a macvlan device is configured
on top of bonding, we want switches to learn about the macvlan
devices as well.   This patch adds a handler to macvlan driver to
propagate these events to all macvlan devices.  We let the generic
inetdev event handler do the work.

This allows macvlan to operated correctly over active-backup
mode bond.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add netpoll support to macvlan devices. Based on the netpoll support in the 802.1q vlan code.

Tested and macvlan could work well with netconsole.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The macvlan dev should always have the same mac address like lowerdev
when in the passthru mode, change the mac address alone will break the
work mechanism, so when the lowerdev or macvlan mac address changes,
we should propagate the changes to another dev.

v1->v2: Allow macvlan dev to change mac address for passthru mode and propagate to
	lowerdev.

v2->v3: Don't set the mac address to the lower dev's unicast address for
	passthru mode when mac address changes.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Macvlan devices try to avoid stacking, but that's not always
successfull or even desired.  As an example, the following
configuration is perefectly legal and valid:

eth0 <--- macvlan0 <---- vlan0.10 <--- macvlan1

However, this configuration produces the following lockdep
trace:
[  115.620418] ======================================================
[  115.620477] [ INFO: possible circular locking dependency detected ]
[  115.620516] 3.15.0-rc1+ #24 Not tainted
[  115.620540] -------------------------------------------------------
[  115.620577] ip/1704 is trying to acquire lock:
[  115.620604]  (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff815df49c>] dev_uc_sync+0x3c/0x80
[  115.620686]
but task is already holding lock:
[  115.620723]  (&macvlan_netdev_addr_lock_key){+.....}, at: [<ffffffff815da5be>] dev_set_rx_mode+0x1e/0x40
[  115.620795]
which lock already depends on the new lock.

[  115.620853]
the existing dependency chain (in reverse order) is:
[  115.620894]
-> #1 (&macvlan_netdev_addr_lock_key){+.....}:
[  115.620935]        [<ffffffff810d57f2>] lock_acquire+0xa2/0x130
[  115.620974]        [<ffffffff816f62e7>] _raw_spin_lock_nested+0x37/0x50
[  115.621019]        [<ffffffffa07296c3>] vlan_dev_set_rx_mode+0x53/0x110 [8021q]
[  115.621066]        [<ffffffff815da557>] __dev_set_rx_mode+0x57/0xa0
[  115.621105]        [<ffffffff815da5c6>] dev_set_rx_mode+0x26/0x40
[  115.621143]        [<ffffffff815da6be>] __dev_open+0xde/0x140
[  115.621174]        [<ffffffff815da9ad>] __dev_change_flags+0x9d/0x170
[  115.621174]        [<ffffffff815daaa9>] dev_change_flags+0x29/0x60
[  115.621174]        [<ffffffff815e7f11>] do_setlink+0x321/0x9a0
[  115.621174]        [<ffffffff815ea59f>] rtnl_newlink+0x51f/0x730
[  115.621174]        [<ffffffff815e6e75>] rtnetlink_rcv_msg+0x95/0x250
[  115.621174]        [<ffffffff81608b19>] netlink_rcv_skb+0xa9/0xc0
[  115.621174]        [<ffffffff815e6dca>] rtnetlink_rcv+0x2a/0x40
[  115.621174]        [<ffffffff81608150>] netlink_unicast+0xf0/0x1c0
[  115.621174]        [<ffffffff8160851f>] netlink_sendmsg+0x2ff/0x740
[  115.621174]        [<ffffffff815bc9db>] sock_sendmsg+0x8b/0xc0
[  115.621174]        [<ffffffff815bd4b9>] ___sys_sendmsg+0x369/0x380
[  115.621174]        [<ffffffff815bdbb2>] __sys_sendmsg+0x42/0x80
[  115.621174]        [<ffffffff815bdc02>] SyS_sendmsg+0x12/0x20
[  115.621174]        [<ffffffff816ffd69>] system_call_fastpath+0x16/0x1b
[  115.621174]
-> #0 (&vlan_netdev_addr_lock_key/1){+.....}:
[  115.621174]        [<ffffffff810d4d43>] __lock_acquire+0x1773/0x1a60
[  115.621174]        [<ffffffff810d57f2>] lock_acquire+0xa2/0x130
[  115.621174]        [<ffffffff816f62e7>] _raw_spin_lock_nested+0x37/0x50
[  115.621174]        [<ffffffff815df49c>] dev_uc_sync+0x3c/0x80
[  115.621174]        [<ffffffffa0696d2a>] macvlan_set_mac_lists+0xca/0x110 [macvlan]
[  115.621174]        [<ffffffff815da557>] __dev_set_rx_mode+0x57/0xa0
[  115.621174]        [<ffffffff815da5c6>] dev_set_rx_mode+0x26/0x40
[  115.621174]        [<ffffffff815da6be>] __dev_open+0xde/0x140
[  115.621174]        [<ffffffff815da9ad>] __dev_change_flags+0x9d/0x170
[  115.621174]        [<ffffffff815daaa9>] dev_change_flags+0x29/0x60
[  115.621174]        [<ffffffff815e7f11>] do_setlink+0x321/0x9a0
[  115.621174]        [<ffffffff815ea59f>] rtnl_newlink+0x51f/0x730
[  115.621174]        [<ffffffff815e6e75>] rtnetlink_rcv_msg+0x95/0x250
[  115.621174]        [<ffffffff81608b19>] netlink_rcv_skb+0xa9/0xc0
[  115.621174]        [<ffffffff815e6dca>] rtnetlink_rcv+0x2a/0x40
[  115.621174]        [<ffffffff81608150>] netlink_unicast+0xf0/0x1c0
[  115.621174]        [<ffffffff8160851f>] netlink_sendmsg+0x2ff/0x740
[  115.621174]        [<ffffffff815bc9db>] sock_sendmsg+0x8b/0xc0
[  115.621174]        [<ffffffff815bd4b9>] ___sys_sendmsg+0x369/0x380
[  115.621174]        [<ffffffff815bdbb2>] __sys_sendmsg+0x42/0x80
[  115.621174]        [<ffffffff815bdc02>] SyS_sendmsg+0x12/0x20
[  115.621174]        [<ffffffff816ffd69>] system_call_fastpath+0x16/0x1b
[  115.621174]
other info that might help us debug this:

[  115.621174]  Possible unsafe locking scenario:

[  115.621174]        CPU0                    CPU1
[  115.621174]        ----                    ----
[  115.621174]   lock(&macvlan_netdev_addr_lock_key);
[  115.621174]                                lock(&vlan_netdev_addr_lock_key/1);
[  115.621174]                                lock(&macvlan_netdev_addr_lock_key);
[  115.621174]   lock(&vlan_netdev_addr_lock_key/1);
[  115.621174]
 *** DEADLOCK ***

[  115.621174] 2 locks held by ip/1704:
[  115.621174]  #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff815e6dbb>] rtnetlink_rcv+0x1b/0x40
[  115.621174]  #1:  (&macvlan_netdev_addr_lock_key){+.....}, at: [<ffffffff815da5be>] dev_set_rx_mode+0x1e/0x40
[  115.621174]
stack backtrace:
[  115.621174] CPU: 3 PID: 1704 Comm: ip Not tainted 3.15.0-rc1+ #24
[  115.621174] Hardware name: Hewlett-Packard HP xw8400 Workstation/0A08h, BIOS 786D5 v02.38 10/25/2010
[  115.621174]  ffffffff82339ae0 ffff880465f79568 ffffffff816ee20c ffffffff82339ae0
[  115.621174]  ffff880465f795a8 ffffffff816e9e1b ffff880465f79600 ffff880465b019c8
[  115.621174]  0000000000000001 0000000000000002 ffff880465b019c8 ffff880465b01230
[  115.621174] Call Trace:
[  115.621174]  [<ffffffff816ee20c>] dump_stack+0x4d/0x66
[  115.621174]  [<ffffffff816e9e1b>] print_circular_bug+0x200/0x20e
[  115.621174]  [<ffffffff810d4d43>] __lock_acquire+0x1773/0x1a60
[  115.621174]  [<ffffffff810d3172>] ? trace_hardirqs_on_caller+0xb2/0x1d0
[  115.621174]  [<ffffffff810d57f2>] lock_acquire+0xa2/0x130
[  115.621174]  [<ffffffff815df49c>] ? dev_uc_sync+0x3c/0x80
[  115.621174]  [<ffffffff816f62e7>] _raw_spin_lock_nested+0x37/0x50
[  115.621174]  [<ffffffff815df49c>] ? dev_uc_sync+0x3c/0x80
[  115.621174]  [<ffffffff815df49c>] dev_uc_sync+0x3c/0x80
[  115.621174]  [<ffffffffa0696d2a>] macvlan_set_mac_lists+0xca/0x110 [macvlan]
[  115.621174]  [<ffffffff815da557>] __dev_set_rx_mode+0x57/0xa0
[  115.621174]  [<ffffffff815da5c6>] dev_set_rx_mode+0x26/0x40
[  115.621174]  [<ffffffff815da6be>] __dev_open+0xde/0x140
[  115.621174]  [<ffffffff815da9ad>] __dev_change_flags+0x9d/0x170
[  115.621174]  [<ffffffff815daaa9>] dev_change_flags+0x29/0x60
[  115.621174]  [<ffffffff811e1db1>] ? mem_cgroup_bad_page_check+0x21/0x30
[  115.621174]  [<ffffffff815e7f11>] do_setlink+0x321/0x9a0
[  115.621174]  [<ffffffff810d394c>] ? __lock_acquire+0x37c/0x1a60
[  115.621174]  [<ffffffff815ea59f>] rtnl_newlink+0x51f/0x730
[  115.621174]  [<ffffffff815ea169>] ? rtnl_newlink+0xe9/0x730
[  115.621174]  [<ffffffff815e6e75>] rtnetlink_rcv_msg+0x95/0x250
[  115.621174]  [<ffffffff810d329d>] ? trace_hardirqs_on+0xd/0x10
[  115.621174]  [<ffffffff815e6dbb>] ? rtnetlink_rcv+0x1b/0x40
[  115.621174]  [<ffffffff815e6de0>] ? rtnetlink_rcv+0x40/0x40
[  115.621174]  [<ffffffff81608b19>] netlink_rcv_skb+0xa9/0xc0
[  115.621174]  [<ffffffff815e6dca>] rtnetlink_rcv+0x2a/0x40
[  115.621174]  [<ffffffff81608150>] netlink_unicast+0xf0/0x1c0
[  115.621174]  [<ffffffff8160851f>] netlink_sendmsg+0x2ff/0x740
[  115.621174]  [<ffffffff815bc9db>] sock_sendmsg+0x8b/0xc0
[  115.621174]  [<ffffffff8119d4af>] ? might_fault+0x5f/0xb0
[  115.621174]  [<ffffffff8119d4f8>] ? might_fault+0xa8/0xb0
[  115.621174]  [<ffffffff8119d4af>] ? might_fault+0x5f/0xb0
[  115.621174]  [<ffffffff815cb51e>] ? verify_iovec+0x5e/0xe0
[  115.621174]  [<ffffffff815bd4b9>] ___sys_sendmsg+0x369/0x380
[  115.621174]  [<ffffffff816faa0d>] ? __do_page_fault+0x11d/0x570
[  115.621174]  [<ffffffff810cfe9f>] ? up_read+0x1f/0x40
[  115.621174]  [<ffffffff816fab04>] ? __do_page_fault+0x214/0x570
[  115.621174]  [<ffffffff8120a10b>] ? mntput_no_expire+0x6b/0x1c0
[  115.621174]  [<ffffffff8120a0b7>] ? mntput_no_expire+0x17/0x1c0
[  115.621174]  [<ffffffff8120a284>] ? mntput+0x24/0x40
[  115.621174]  [<ffffffff815bdbb2>] __sys_sendmsg+0x42/0x80
[  115.621174]  [<ffffffff815bdc02>] SyS_sendmsg+0x12/0x20
[  115.621174]  [<ffffffff816ffd69>] system_call_fastpath+0x16/0x1b

Fix this by correctly providing macvlan lockdep class.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>