CONFIG_FRAME_POINTERS=y results in much better debug info for the
kernel (clear and precise backtraces), with the only drawback being
a ~1% increase in kernel size.

So offer it unconditionally and enable it by default.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Currently fault-injection capability for SLAB allocator is only
available to SLAB. This patch makes it available to SLUB, too.

[penberg@cs.helsinki.fi: unify slab and slub implementations]
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>

This patch fixes a long-standing performance bug in classic RCU that
results in massive internal-to-RCU lock contention on systems with
more than a few hundred CPUs.  Although this patch creates a separate
flavor of RCU for ease of review and patch maintenance, it is intended
to replace classic RCU.

This patch still handles stress better than does mainline, so I am still
calling it ready for inclusion.  This patch is against the -tip tree.
Nevertheless, experience on an actual 1000+ CPU machine would still be
most welcome.

Most of the changes noted below were found while creating an rcutiny
(which should permit ejecting the current rcuclassic) and while doing
detailed line-by-line documentation.

Updates from v9 (http://lkml.org/lkml/2008/12/2/334):

o	Fixes from remainder of line-by-line code walkthrough,
	including comment spelling, initialization, undesirable
	narrowing due to type conversion, removing redundant memory
	barriers, removing redundant local-variable initialization,
	and removing redundant local variables.

	I do not believe that any of these fixes address the CPU-hotplug
	issues that Andi Kleen was seeing, but please do give it a whirl
	in case the machine is smarter than I am.

	A writeup from the walkthrough may be found at the following
	URL, in case you are suffering from terminal insomnia or
	masochism:

	http://www.kernel.org/pub/linux/kernel/people/paulmck/tmp/rcutree-walkthrough.2008.12.16a.pdf

o	Made rcutree tracing use seq_file, as suggested some time
	ago by Lai Jiangshan.

o	Added a .csv variant of the rcudata debugfs trace file, to allow
	people having thousands of CPUs to drop the data into
	a spreadsheet.	Tested with oocalc and gnumeric.  Updated
	documentation to suit.

Updates from v8 (http://lkml.org/lkml/2008/11/15/139):

o	Fix a theoretical race between grace-period initialization and
	force_quiescent_state() that could occur if more than three
	jiffies were required to carry out the grace-period
	initialization.  Which it might, if you had enough CPUs.

o	Apply Ingo's printk-standardization patch.

o	Substitute local variables for repeated accesses to global
	variables.

o	Fix comment misspellings and redundant (but harmless) increments
	of ->n_rcu_pending (this latter after having explicitly added it).

o	Apply checkpatch fixes.

Updates from v7 (http://lkml.org/lkml/2008/10/10/291):

o	Fixed a number of problems noted by Gautham Shenoy, including
	the cpu-stall-detection bug that he was having difficulty
	convincing me was real.  ;-)

o	Changed cpu-stall detection to wait for ten seconds rather than
	three in order to reduce false positive, as suggested by Ingo
	Molnar.

o	Produced a design document (http://lwn.net/Articles/305782/).
	The act of writing this document uncovered a number of both
	theoretical and "here and now" bugs as noted below.

o	Fix dynticks_nesting accounting confusion, simplify WARN_ON()
	condition, fix kerneldoc comments, and add memory barriers
	in dynticks interface functions.

o	Add more data to tracing.

o	Remove unused "rcu_barrier" field from rcu_data structure.

o	Count calls to rcu_pending() from scheduling-clock interrupt
	to use as a surrogate timebase should jiffies stop counting.

o	Fix a theoretical race between force_quiescent_state() and
	grace-period initialization.  Yes, initialization does have to
	go on for some jiffies for this race to occur, but given enough
	CPUs...

Updates from v6 (http://lkml.org/lkml/2008/9/23/448):

o	Fix a number of checkpatch.pl complaints.

o	Apply review comments from Ingo Molnar and Lai Jiangshan
	on the stall-detection code.

o	Fix several bugs in !CONFIG_SMP builds.

o	Fix a misspelled config-parameter name so that RCU now announces
	at boot time if stall detection is configured.

o	Run tests on numerous combinations of configurations parameters,
	which after the fixes above, now build and run correctly.

Updates from v5 (http://lkml.org/lkml/2008/9/15/92, bad subject line):

o	Fix a compiler error in the !CONFIG_FANOUT_EXACT case (blew a
	changeset some time ago, and finally got around to retesting
	this option).

o	Fix some tracing bugs in rcupreempt that caused incorrect
	totals to be printed.

o	I now test with a more brutal random-selection online/offline
	script (attached).  Probably more brutal than it needs to be
	on the people reading it as well, but so it goes.

o	A number of optimizations and usability improvements:

	o	Make rcu_pending() ignore the grace-period timeout when
		there is no grace period in progress.

	o	Make force_quiescent_state() avoid going for a global
		lock in the case where there is no grace period in
		progress.

	o	Rearrange struct fields to improve struct layout.

	o	Make call_rcu() initiate a grace period if RCU was
		idle, rather than waiting for the next scheduling
		clock interrupt.

	o	Invoke rcu_irq_enter() and rcu_irq_exit() only when
		idle, as suggested by Andi Kleen.  I still don't
		completely trust this change, and might back it out.

	o	Make CONFIG_RCU_TRACE be the single config variable
		manipulated for all forms of RCU, instead of the prior
		confusion.

	o	Document tracing files and formats for both rcupreempt
		and rcutree.

Updates from v4 for those missing v5 given its bad subject line:

o	Separated dynticks interface so that NMIs and irqs call separate
	functions, greatly simplifying it.  In particular, this code
	no longer requires a proof of correctness.  ;-)

o	Separated dynticks state out into its own per-CPU structure,
	avoiding the duplicated accounting.

o	The case where a dynticks-idle CPU runs an irq handler that
	invokes call_rcu() is now correctly handled, forcing that CPU
	out of dynticks-idle mode.

o	Review comments have been applied (thank you all!!!).
	For but one example, fixed the dynticks-ordering issue that
	Manfred pointed out, saving me much debugging.  ;-)

o	Adjusted rcuclassic and rcupreempt to handle dynticks changes.

Attached is an updated patch to Classic RCU that applies a hierarchy,
greatly reducing the contention on the top-level lock for large machines.
This passes 10-hour concurrent rcutorture and online-offline testing on
128-CPU ppc64 without dynticks enabled, and exposes some timekeeping
bugs in presence of dynticks (exciting working on a system where
"sleep 1" hangs until interrupted...), which were fixed in the
2.6.27 kernel.  It is getting more reliable than mainline by some
measures, so the next version will be against -tip for inclusion.
See also Manfred Spraul's recent patches (or his earlier work from
2004 at http://marc.info/?l=linux-kernel&m=108546384711797&w=2).
We will converge onto a common patch in the fullness of time, but are
currently exploring different regions of the design space.  That said,
I have already gratefully stolen quite a few of Manfred's ideas.

This patch provides CONFIG_RCU_FANOUT, which controls the bushiness
of the RCU hierarchy.  Defaults to 32 on 32-bit machines and 64 on
64-bit machines.  If CONFIG_NR_CPUS is less than CONFIG_RCU_FANOUT,
there is no hierarchy.  By default, the RCU initialization code will
adjust CONFIG_RCU_FANOUT to balance the hierarchy, so strongly NUMA
architectures may choose to set CONFIG_RCU_FANOUT_EXACT to disable
this balancing, allowing the hierarchy to be exactly aligned to the
underlying hardware.  Up to two levels of hierarchy are permitted
(in addition to the root node), allowing up to 16,384 CPUs on 32-bit
systems and up to 262,144 CPUs on 64-bit systems.  I just know that I
am going to regret saying this, but this seems more than sufficient
for the foreseeable future.  (Some architectures might wish to set
CONFIG_RCU_FANOUT=4, which would limit such architectures to 64 CPUs.
If this becomes a real problem, additional levels can be added, but I
doubt that it will make a significant difference on real hardware.)

In the common case, a given CPU will manipulate its private rcu_data
structure and the rcu_node structure that it shares with its immediate
neighbors.  This can reduce both lock and memory contention by multiple
orders of magnitude, which should eliminate the need for the strange
manipulations that are reported to be required when running Linux on
very large systems.

Some shortcomings:

o	More bugs will probably surface as a result of an ongoing
	line-by-line code inspection.

	Patches will be provided as required.

o	There are probably hangs, rcutorture failures, &c.  Seems
	quite stable on a 128-CPU machine, but that is kind of small
	compared to 4096 CPUs.  However, seems to do better than
	mainline.

	Patches will be provided as required.

o	The memory footprint of this version is several KB larger
	than rcuclassic.

	A separate UP-only rcutiny patch will be provided, which will
	reduce the memory footprint significantly, even compared
	to the old rcuclassic.  One such patch passes light testing,
	and has a memory footprint smaller even than rcuclassic.
	Initial reaction from various embedded guys was "it is not
	worth it", so am putting it aside.

Credits:

o	Manfred Spraul for ideas, review comments, and bugs spotted,
	as well as some good friendly competition.  ;-)

o	Josh Triplett, Ingo Molnar, Peter Zijlstra, Mathieu Desnoyers,
	Lai Jiangshan, Andi Kleen, Andy Whitcroft, and Andrew Morton
	for reviews and comments.

o	Thomas Gleixner for much-needed help with some timer issues
	(see patches below).

o	Jon M. Tollefson, Tim Pepper, Andrew Theurer, Jose R. Santos,
	Andy Whitcroft, Darrick Wong, Nishanth Aravamudan, Anton
	Blanchard, Dave Kleikamp, and Nathan Lynch for keeping machines
	alive despite my heavy abuse^Wtesting.
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: add .config driven boot parameter default value

Right now debugobjects can only be activated if the debug_objects
boot parameter is passed in via the boot command line.

Make this more convenient (and randomizable) by also providing
a .config method. Enable it by default. (DEBUG_OBJECTS itself
is default-off)
Signed-off-by: NIngo Molnar <mingo@elte.hu>

CONFIG_DEBUG_BLOCK_EXT_DEVT can break booting even on some modern
distros.  Add BIG FAT WARNING to keep people at a safe distance.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Base infrastructure to enable per-module debug messages.

I've introduced CONFIG_DYNAMIC_PRINTK_DEBUG, which when enabled centralizes
control of debugging statements on a per-module basis in one /proc file,
currently, <debugfs>/dynamic_printk/modules. When, CONFIG_DYNAMIC_PRINTK_DEBUG,
is not set, debugging statements can still be enabled as before, often by
defining 'DEBUG' for the proper compilation unit. Thus, this patch set has no
affect when CONFIG_DYNAMIC_PRINTK_DEBUG is not set.

The infrastructure currently ties into all pr_debug() and dev_dbg() calls. That
is, if CONFIG_DYNAMIC_PRINTK_DEBUG is set, all pr_debug() and dev_dbg() calls
can be dynamically enabled/disabled on a per-module basis.

Future plans include extending this functionality to subsystems, that define 
their own debug levels and flags.

Usage:

Dynamic debugging is controlled by the debugfs file, 
<debugfs>/dynamic_printk/modules. This file contains a list of the modules that
can be enabled. The format of the file is as follows:

	<module_name> <enabled=0/1>
		.
		.
		.

	<module_name> : Name of the module in which the debug call resides
	<enabled=0/1> : whether the messages are enabled or not

For example:

	snd_hda_intel enabled=0
	fixup enabled=1
	driver enabled=0

Enable a module:

	$echo "set enabled=1 <module_name>" > dynamic_printk/modules

Disable a module:

	$echo "set enabled=0 <module_name>" > dynamic_printk/modules

Enable all modules:

	$echo "set enabled=1 all" > dynamic_printk/modules

Disable all modules:

	$echo "set enabled=0 all" > dynamic_printk/modules

Finally, passing "dynamic_printk" at the command line enables
debugging for all modules. This mode can be turned off via the above
disable command.

[gkh: minor cleanups and tweaks to make the build work quietly]
Signed-off-by: NJason Baron <jbaron@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Only works for the generic request timer handling. Allows one to
sporadically ignore request completions, thus exercising the timeout
handling.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

DEBUG_BLOCK_EXT_DEVT shuffles SCSI and IDE device numbers and root
device number set using rdev become meaningless.  Root devices should
be explicitly specified using textual names.  Warn about it if root
can't be found and DEBUG_BLOCK_EXT_DEVT is enabled.  Also, add warning
to the help text.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

It's a debug option that you would explicitly enable to test this
feature, we should default it to 'n' to prevent accidental surprises
for now.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Extended devt introduces non-contiguos device numbers.  This patch
implements a debug option which forces most devt allocations to be
from the extended area and spreads them out.  This is enabled by
default if DEBUG_KERNEL is set and achieves...

1. Detects code paths in kernel or userland which expect predetermined
   consecutive device numbers.

2. When something goes wrong, avoid corruption as adding to the minor
   of earlier partition won't lead to the wrong but valid device.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

This patch adds stalled-CPU detection to Classic RCU.  This capability
is enabled by a new config variable CONFIG_RCU_CPU_STALL_DETECTOR, which
defaults disabled.

This is a debugging feature to detect infinite loops in kernel code, not
something that non-kernel-hackers would be expected to care about.

This feature can detect looping CPUs in !PREEMPT builds and looping CPUs
with preemption disabled in PREEMPT builds.  This is essentially a port of
this functionality from the treercu patch, replacing the stall debug patch
that is already in tip/core/rcu (commit 67182ae1).

The changes from the patch in tip/core/rcu include making the config
variable name match that in treercu, changing from seconds to jiffies to
avoid spurious warnings, and printing a boot message when this feature
is enabled.
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

during some development we suspected a case where we left something
in a notifier chain that was from a module that was unloaded already...
and that sort of thing is rather hard to track down.

This patch adds a very simple sanity check (which isn't all that
expensive) to make sure the notifier we're about to call is
actually from either the kernel itself of from a still-loaded
module, avoiding a hard-to-chase-down crash.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This bug is causing random crashes
(http://bugzilla.kernel.org/show_bug.cgi?id=11414).

-fno-omit-frame-pointer is only needed on powerpc when -pg is also
supplied, and there is a gcc bug that causes incorrect code generation
on 32-bit powerpc when -fno-omit-frame-pointer is used---it uses stack
locations below the stack pointer, which is not allowed by the ABI
because those locations can and sometimes do get corrupted by an
interrupt.

This ensures that CONFIG_FRAME_POINTER is only selected by ftrace.
When CONFIG_FTRACE is enabled we also pass -mno-sched-epilog to work
around the gcc codegen bug.

Patch based on work by:
	Andreas Schwab <schwab@suse.de>
	Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

I noticed that sysctl_check.o was the largest object file in
a allnoconfig build in kernel/*.

  36243       0       0   36243    8d93 kernel/sysctl_check.o

This is because it was default y and && EMBEDDED. But I don't
really see a need for a non kernel developer to have their
sysctls checked all the time.

So move the Kconfig into the kernel debugging section and
also drop the default y and the EMBEDDED check.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently source files in the Documentation/ sub-dir can easily bit-rot
since they are not generally buildable, either because they are hidden in
text files or because there are no Makefile rules for them.  This needs to
be fixed so that the source files remain usable and good examples of code
instead of bad examples.

Add the ability to build source files that are in the Documentation/ dir.
Add to Kconfig as "BUILD_DOCSRC" config symbol.

Use "CONFIG_BUILD_DOCSRC=1 make ..." to build objects from the
Documentation/ sources.  Or enable BUILD_DOCSRC in the *config system.
However, this symbol depends on HEADERS_CHECK since the header files need
to be installed (for userspace builds).

Built (using cross-tools) for x86-64, i386, alpha, ia64, sparc32,
sparc64, powerpc, sh, m68k, & mips.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Reviewed-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

this is a diagnostic patch for Classic RCU.

The approach is to record a timestamp at the beginning
of the grace period (in rcu_start_batch()), then have
rcu_check_callbacks() complain if:

 1.	it is running on a CPU that has holding up grace periods for
 	a long time (say one second).  This will identify the culprit
 	assuming that the culprit has not disabled hardware irqs,
 	instruction execution, or some such.

 2.	it is running on a CPU that is not holding up grace periods,
 	but grace periods have been held up for an even longer time
 	(say two seconds).

It is enabled via the default-off CONFIG_DEBUG_RCU_STALL kernel parameter.

Rather than exponential backoff, it backs off to once per 30 seconds.
My feeling upon thinking on it was that if you have stalled RCU grace
periods for that long, a few extra printk() messages are probably the
least of your worries...
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: David Witbrodt <dawitbro@sbcglobal.net>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Boot initialisation is very complex, with significant numbers of
architecture-specific routines, hooks and code ordering.  While significant
amounts of the initialisation is architecture-independent, it trusts the data
received from the architecture layer.  This is a mistake, and has resulted in
a number of difficult-to-diagnose bugs.

This patchset adds some validation and tracing to memory initialisation.  It
also introduces a few basic defensive measures.  The validation code can be
explicitly disabled for embedded systems.

This patch:

Add additional debugging and verification code for memory initialisation.

Once enabled, the verification checks are always run and when required
additional debugging information may be outputted via a mminit_loglevel=
command-line parameter.

The verification code is placed in a new file mm/mm_init.c.  Ideally other mm
initialisation code will be moved here over time.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Cc: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds saved stack-traces to the backtrace suite of self-tests.

Note that we don't depend on or unconditionally enable CONFIG_STACKTRACE
because not all architectures may have it (and we still want to enable the
other tests for those architectures).

Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: NVegard Nossum <vegard.nossum@gmail.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Add some (configurable) expensive sanity checking to catch wrong address
translations on x86.

- create linux/mmdebug.h file to be able include this file in
  asm headers to not get unsolvable loops in header files
- __phys_addr on x86_32 became a function in ioremap.c since
  PAGE_OFFSET, is_vmalloc_addr and VMALLOC_* non-constasts are undefined
  if declared in page_32.h
- add __phys_addr_const for initializing doublefault_tss.__cr3

Tested on 386, 386pae, x86_64 and x86_64 numa=fake=2.

Contains Andi's enable numa virtual address debug patch.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This patch re-institutes the ability to build rcutorture directly into
the Linux kernel.  The reason that this capability was removed was that
this could result in your kernel being pretty much useless, as rcutorture
would be running starting from early boot.  This problem has been avoided
by (1) making rcutorture run only three seconds of every six by default,
(2) adding a CONFIG_RCU_TORTURE_TEST_RUNNABLE that permits rcutorture
to be quiesced at boot time, and (3) adding a sysctl in /proc named
/proc/sys/kernel/rcutorture_runnable that permits rcutorture to be
quiesced and unquiesced when built into the kernel.

Please note that this /proc file is -not- available when rcutorture
is built as a module.  Please also note that to get the earlier
take-no-prisoners behavior, you must use the boot command line to set
rcutorture's "stutter" parameter to zero.

The rcutorture quiescing mechanism is currently quite crude: loops
in each rcutorture process that poll a global variable once per tick.
Suggestions for improvement are welcome.  The default action will
be to reduce the polling rate to a few times per second.
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Suggested-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This reverts commit 9aaffc89.

That commit was a very bad idea. RCU_TORTURE found many boot timing
bugs and other sorts of bugs in the past, so excluding it from
boot images is very silly.

The option already depends on DEBUG_KERNEL and is disabled by default.
Even when it runs, the test threads are reniced. If it annoys people
we could add a runtime sysctl.

Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

allow users to configure the softlockup detector to generate a panic
instead of a warning message.

high-availability systems might opt for this strict method (combined
with panic_timeout= boot option/sysctl), instead of generating
softlockup warnings ad infinitum.

also, automated tests work better if the system reboots reliably (into
a safe kernel) in case of a lockup.

The full spectrum of configurability is supported: boot option, sysctl
option and Kconfig option.

it's default-disabled.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

If CONFIG_FTRACE is selected and /proc/sys/kernel/ftrace_enabled is
set to a non-zero value the ftrace routine will be called everytime
we enter a kernel function that is not marked with the "notrace"
attribute.

The ftrace routine will then call a registered function if a function
happens to be registered.

[ This code has been highly hacked by Steven Rostedt and Ingo Molnar,
  so don't blame Arnaldo for all of this ;-) ]

Update:
  It is now possible to register more than one ftrace function.
  If only one ftrace function is registered, that will be the
  function that ftrace calls directly. If more than one function
  is registered, then ftrace will call a function that will loop
  through the functions to call.
Signed-off-by: NArnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Add calls to the generic object debugging infrastructure and provide fixup
functions which allow to keep the system alive when recoverable problems have
been detected by the object debugging core code.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NIngo Molnar <mingo@elte.hu>
Cc: Greg KH <greg@kroah.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We can see an ever repeating problem pattern with objects of any kind in the
kernel:

1) freeing of active objects
2) reinitialization of active objects

Both problems can be hard to debug because the crash happens at a point where
we have no chance to decode the root cause anymore.  One problem spot are
kernel timers, where the detection of the problem often happens in interrupt
context and usually causes the machine to panic.

While working on a timer related bug report I had to hack specialized code
into the timer subsystem to get a reasonable hint for the root cause.  This
debug hack was fine for temporary use, but far from a mergeable solution due
to the intrusiveness into the timer code.

The code further lacked the ability to detect and report the root cause
instantly and keep the system operational.

Keeping the system operational is important to get hold of the debug
information without special debugging aids like serial consoles and special
knowledge of the bug reporter.

The problems described above are not restricted to timers, but timers tend to
expose it usually in a full system crash.  Other objects are less explosive,
but the symptoms caused by such mistakes can be even harder to debug.

Instead of creating specialized debugging code for the timer subsystem a
generic infrastructure is created which allows developers to verify their code
and provides an easy to enable debug facility for users in case of trouble.

The debugobjects core code keeps track of operations on static and dynamic
objects by inserting them into a hashed list and sanity checking them on
object operations and provides additional checks whenever kernel memory is
freed.

The tracked object operations are:
- initializing an object
- adding an object to a subsystem list
- deleting an object from a subsystem list

Each operation is sanity checked before the operation is executed and the
subsystem specific code can provide a fixup function which allows to prevent
the damage of the operation.  When the sanity check triggers a warning message
and a stack trace is printed.

The list of operations can be extended if the need arises.  For now it's
limited to the requirements of the first user (timers).

The core code enqueues the objects into hash buckets.  The hash index is
generated from the address of the object to simplify the lookup for the check
on kfree/vfree.  Each bucket has it's own spinlock to avoid contention on a
global lock.

The debug code can be compiled in without being active.  The runtime overhead
is minimal and could be optimized by asm alternatives.  A kernel command line
option enables the debugging code.

Thanks to Ingo Molnar for review, suggestions and cleanup patches.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Greg KH <greg@kroah.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add option to enable -Wframe-larger-than= on gcc 4.4

gcc mainline (upcoming 4.4) added a new -Wframe-larger-than=...
option to warn at build time about too large stack frames. Add a config
option to enable this warning, since this very useful for the kernel.

I choose (somewhat arbitarily) 2048 as default warning threshold for 64bit
and 1024 as default for 32bit architectures.  With some research and
fixing all the code for smaller values these defaults should be probably
lowered.

With the default allyesconfigs have some new warnings, but I think
that is all code that should be just fixed.

At some point (when gcc 4.4 is released and widely used) this should
obsolete make checkstack
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

There have been a few oopses caused by 'struct file's with NULL f_vfsmnts.
There was also a set of potentially missed mnt_want_write()s from
dentry_open() calls.

This patch provides a very simple debugging framework to catch these kinds of
bugs.  It will WARN_ON() them, but should stop us from having any oopses or
mnt_writer count imbalances.

I'm quite convinced that this is a good thing because it found bugs in the
stuff I was working on as soon as I wrote it.

[hch: made it conditional on a debug option.
      But it's still a little bit too ugly]

[hch: merged forced remount r/o fix from Dave and akpm's fix for the fix]
Signed-off-by: NDave Hansen <haveblue@us.ibm.com>
Acked-by: NAl Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

This way firewire-ohci can be used for remote debugging like ohci1394.
Version with amendment from Fri, 11 Apr 2008 00:08:08 +0200.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NBernhard Kaindl <bk@suse.de>

kgdb core code. Handles the protocol and the arch details.

[ mingo@elte.hu: heavily modified, simplified and cleaned up. ]
[ xemul@openvz.org: use find_task_by_pid_ns ]
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NJan Kiszka <jan.kiszka@web.de>
Reviewed-by: NThomas Gleixner <tglx@linutronix.de>

Alpha and FRV mutexes had an option to print lots of debugging messages
in their semaphore implementation.  This feature has not been carried
over to the generic semaphores, so remove the stale Kconfig option.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>

count_partial() is used by both slabinfo and the sysfs proc support. Move
the function directly before the beginning of the sysfs code so that it can
be easily found. Rework the preprocessor conditional to take into account
that slub sysfs support depends on CONFIG_SYSFS *and* CONFIG_SLUB_DEBUG.

Make CONFIG_SLUB_STATS depend on CONFIG_SLUB_DEBUG and CONFIG_SYSFS. There
is no point of keeping statistics if no one can restrive them.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>

Make LKDTM depend on BLOCK to prevent build failures with certain configs.
Signed-off-by: NChris Snook <csnook@redhat.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We started to see patches enabling this - so explain why
it is disabled and the condition to enable it again.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Other than the defconfigs, remove the entry in compiler-gcc4.h,
Kconfig.debug and feature-removal-schedule.txt.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Add architecture support for the MN10300/AM33 CPUs produced by MEI to the
kernel.

This patch also adds board support for the ASB2303 with the ASB2308 daughter
board, and the ASB2305.  The only processor supported is the MN103E010, which
is an AM33v2 core plus on-chip devices.

[akpm@linux-foundation.org: nuke cvs control strings]
Signed-off-by: NMasakazu Urade <urade.masakazu@jp.panasonic.com>
Signed-off-by: NKoichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The statistics provided here allow the monitoring of allocator behavior but
at the cost of some (minimal) loss of performance. Counters are placed in
SLUB's per cpu data structure. The per cpu structure may be extended by the
statistics to grow larger than one cacheline which will increase the cache
footprint of SLUB.

There is a compile option to enable/disable the inclusion of the runtime
statistics and its off by default.

The slabinfo tool is enhanced to support these statistics via two options:

-D 	Switches the line of information displayed for a slab from size
	mode to activity mode.

-A	Sorts the slabs displayed by activity. This allows the display of
	the slabs most important to the performance of a certain load.

-r	Report option will report detailed statistics on

Example (tbench load):

slabinfo -AD		->Shows the most active slabs

Name                   Objects    Alloc     Free   %Fast
skbuff_fclone_cache         33 111953835 111953835  99  99
:0000192                  2666  5283688  5281047  99  99
:0001024                   849  5247230  5246389  83  83
vm_area_struct            1349   119642   118355  91  22
:0004096                    15    66753    66751  98  98
:0000064                  2067    25297    23383  98  78
dentry                   10259    28635    18464  91  45
:0000080                 11004    18950     8089  98  98
:0000096                  1703    12358    10784  99  98
:0000128                   762    10582     9875  94  18
:0000512                   184     9807     9647  95  81
:0002048                   479     9669     9195  83  65
anon_vma                   777     9461     9002  99  71
kmalloc-8                 6492     9981     5624  99  97
:0000768                   258     7174     6931  58  15

So the skbuff_fclone_cache is of highest importance for the tbench load.
Pretty high load on the 192 sized slab. Look for the aliases

slabinfo -a | grep 000192
:0000192     <- xfs_btree_cur filp kmalloc-192 uid_cache tw_sock_TCP
	request_sock_TCPv6 tw_sock_TCPv6 skbuff_head_cache xfs_ili

Likely skbuff_head_cache.


Looking into the statistics of the skbuff_fclone_cache is possible through

slabinfo skbuff_fclone_cache	->-r option implied if cache name is mentioned


.... Usual output ...

Slab Perf Counter       Alloc     Free %Al %Fr
--------------------------------------------------
Fastpath             111953360 111946981  99  99
Slowpath                 1044     7423   0   0
Page Alloc                272      264   0   0
Add partial                25      325   0   0
Remove partial             86      264   0   0
RemoteObj/SlabFrozen      350     4832   0   0
Total                111954404 111954404

Flushes       49 Refill        0
Deactivate Full=325(92%) Empty=0(0%) ToHead=24(6%) ToTail=1(0%)

Looks good because the fastpath is overwhelmingly taken.


skbuff_head_cache:

Slab Perf Counter       Alloc     Free %Al %Fr
--------------------------------------------------
Fastpath              5297262  5259882  99  99
Slowpath                 4477    39586   0   0
Page Alloc                937      824   0   0
Add partial                 0     2515   0   0
Remove partial           1691      824   0   0
RemoteObj/SlabFrozen     2621     9684   0   0
Total                 5301739  5299468

Deactivate Full=2620(100%) Empty=0(0%) ToHead=0(0%) ToTail=0(0%)


Descriptions of the output:

Total:		The total number of allocation and frees that occurred for a
		slab

Fastpath:	The number of allocations/frees that used the fastpath.

Slowpath:	Other allocations

Page Alloc:	Number of calls to the page allocator as a result of slowpath
		processing

Add Partial:	Number of slabs added to the partial list through free or
		alloc (occurs during cpuslab flushes)

Remove Partial:	Number of slabs removed from the partial list as a result of
		allocations retrieving a partial slab or by a free freeing
		the last object of a slab.

RemoteObj/Froz:	How many times were remotely freed object encountered when a
		slab was about to be deactivated. Frozen: How many times was
		free able to skip list processing because the slab was in use
		as the cpuslab of another processor.

Flushes:	Number of times the cpuslab was flushed on request
		(kmem_cache_shrink, may result from races in __slab_alloc)

Refill:		Number of times we were able to refill the cpuslab from
		remotely freed objects for the same slab.

Deactivate:	Statistics how slabs were deactivated. Shows how they were
		put onto the partial list.

In general fastpath is very good. Slowpath without partial list processing is
also desirable. Any touching of partial list uses node specific locks which
may potentially cause list lock contention.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>

Including additional fixes from Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

We have too many section mismatches detected at the moment.
So silence modpost and prevent the option from being
set in a typical allyesconfig build.

Tell the user how to see all the deteils in the summary
message from modpost.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>