When the interface runs out of the allocated entries in VLAN table,
we program the interface in VLAN promiscuous mode.
Use OPCODE_COMMON_NTWK_RX_FILTER to set VLAN Promiscuous mode
instead of OPCODE_COMMON_NTWK_VLAN_CONFIG.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Size of be_nic_res_desc structure is incorrect. Fix it.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tx on SH-R can lockup if the packet size is less than 32 bytes.
Pad such packets to a safer 36-byte size.
Patch uses the Lancer-R workaround - which checks for packet <= 32-bytes
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

John W. Linville says:

====================
Regarding the Bluetooth bits, Gustavo says:

"First Bluetooth fixes to 3.12, it includes:

* 3 patches to add device id for 3 new hardwares.

* 2 patches from Johan to fix the rfkill behaviour during setup stage

* a small clean up in the rfcomm TTY code that fixes a potential racy
condition (by Gianluca Anzolin)

* 2 fixes to proper set encryption key size and security level in the
peripheral role of Bluetooth LE devices. (by Andre Guedes)

* a fix for dealing devices where pairing is not necessary, we were keeping
the Bluetooth ACL connection alive for too much time. (by Syam Sidhardhan)"

Also, I fixed-up an curly-brace indentation problem in the Bluetooth
code while merging.  On top of that...

Alexey Khoroshilov brings a p54usb fix to avoid a resource leak when
request_firmware_nowait fails.

Amitkumar Karwar fixes a firmware hang caused by too much header data
being appended for USB devices using the mwifiex driver.

Arend van Spriel provides three fixes: a brcmfmac fix to relocate some
driver code outside of an .init section; a scheduling while atomic
fix for bcma; and, another scheduling while atomic fix for brcmsmac.

Bing Zhao offers a pair of mwifiex fixes: a code change to avoid
firmware timeouts on USB; and a fix for a NULL pointer dereference.

Christian Lamparter adds a device ID to p54usb.

Felix Fietkau implements a quartet of small ath9k fixes, including
a locking fix, a list management fix, a fix to properly mark a stale
buffer, and an aggregate buffering fix.

Larry Finger champions a data alignment fix to make rtlwifi work
better with ARM builds.

Solomon Peachy reverts an earlier interrupt handling fix for cw1200
and replaces it with a new threaded oneshot irq handler implementation.

Sujith Manoharan fixes an ath9k regression by reverting an earlier
patch.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to igb and i40e.

Todd provides a fix for 82580 devices in igb, where the ethtool
loopback test was missing 82580 copper devices.

Jesse provides five fixes/cleanups to i40e based on feedback from
Joe Perches and the community.

v2: fixed up patch 5 in the series based on feedback from Joe Perches
    and David Miller
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

Also fixed-up a badly indented closing brace...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

coccicheck shows:

drivers/net/ethernet/intel/i40e/i40e_adminq.c:704:2-8: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_adminq.c:763:1-7: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_adminq.c:810:2-8: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_common.c:510:2-8: Replace memcpy
with struct assignment

Fix each of them with a *a = *b;
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As mentioned by Joe Perches, clean up return values in some functions
making sure to have consistent return types, not mixing types.

A couple of Joe's comments suggested returning void, but since
the functions in question are ndo defined, the return values are fixed.
So make a comment in the header that notes this is a function called by
net_device_ops.

v2: fix post increment bug in return

CC: Joe Perches <joe@perches.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When calling admin queue functions the driver should use aq_ret
variable to help make clear that the return value is not a regular
return variable.

This allows for clean up of the return types that were previously
converted to int.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As mentioned by Joe Perches clean up a loop flow.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joe Perches <joe@perches.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As mentioned by Joe Perches, we should be using
foo = alloc(...)
if (!foo)
	return -ENOMEM;

return 0;
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joe Perches <joe@perches.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add back 82580 loopback tests to ethtool.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Outgoing packets sent by via-rhine have their VLAN PCP field off by one
(when hardware acceleration is enabled). The TX descriptor expects only VID
and PCP (without a CFI/DEI bit).

Peter Boström noticed and reported the bug.
Signed-off-by: NRoger Luethi <rl@hellgate.ch>
Cc: Peter Boström <peter.bostrom@netrounds.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds explicit call to bcma_core_pci_power_save() from
a non-atomic context resolving 'scheduling while atomic' issue.

[   13.224317] BUG: scheduling while atomic: dhcpcd/1800/0x00000202
[   13.224322] Modules linked in: brcmsmac nouveau coretemp kvm_intel kvm cordic brcmutil bcma dell_wmi atl1c ttm mxm_wmi wmi
[   13.224354] CPU: 0 PID: 1800 Comm: dhcpcd Tainted: G        W    3.11.0-wl #1
[   13.224359] Hardware name: Alienware M11x R2/M11x R2, BIOS A04 11/23/2010
[   13.224363]  ffff880177c12c40 ffff880170fd1968 ffffffff8169af5b 0000000000000007
[   13.224374]  ffff880170fd1ad0 ffff880170fd1978 ffffffff81697ee2 ffff880170fd19f8
[   13.224383]  ffffffff816a19f5 00000000000f4240 000000000000d080 ffff880170fd1fd8
[   13.224391] Call Trace:
[   13.224399]  [<ffffffff8169af5b>] dump_stack+0x4f/0x84
[   13.224403]  [<ffffffff81697ee2>] __schedule_bug+0x43/0x51
[   13.224409]  [<ffffffff816a19f5>] __schedule+0x6e5/0x810
[   13.224412]  [<ffffffff816a1c34>] schedule+0x24/0x70
[   13.224416]  [<ffffffff816a04fc>] schedule_hrtimeout_range_clock+0x10c/0x150
[   13.224420]  [<ffffffff810684e0>] ? update_rmtp+0x60/0x60
[   13.224424]  [<ffffffff8106915f>] ? hrtimer_start_range_ns+0xf/0x20
[   13.224429]  [<ffffffff816a054e>] schedule_hrtimeout_range+0xe/0x10
[   13.224432]  [<ffffffff8104f6fb>] usleep_range+0x3b/0x40
[   13.224437]  [<ffffffffa003733a>] bcma_pcie_mdio_read.isra.5+0x8a/0x100 [bcma]
[   13.224442]  [<ffffffffa00374a5>] bcma_pcie_mdio_writeread.isra.6.constprop.13+0x25/0x30 [bcma]
[   13.224448]  [<ffffffffa00374f9>] bcma_core_pci_power_save+0x49/0x80 [bcma]
[   13.224452]  [<ffffffffa003765d>] bcma_core_pci_up+0x2d/0x60 [bcma]
[   13.224460]  [<ffffffffa03dc17c>] brcms_c_up+0xfc/0x430 [brcmsmac]
[   13.224467]  [<ffffffffa03d1a7d>] brcms_up+0x1d/0x20 [brcmsmac]
[   13.224473]  [<ffffffffa03d2498>] brcms_ops_start+0x298/0x340 [brcmsmac]
[   13.224478]  [<ffffffff81600a12>] ? cfg80211_netdev_notifier_call+0xd2/0x5f0
[   13.224483]  [<ffffffff815fa53d>] ? packet_notifier+0xad/0x1d0
[   13.224487]  [<ffffffff81656e75>] ieee80211_do_open+0x325/0xf80
[   13.224491]  [<ffffffff8106ac09>] ? __raw_notifier_call_chain+0x9/0x10
[   13.224495]  [<ffffffff81657b41>] ieee80211_open+0x71/0x80
[   13.224498]  [<ffffffff81526267>] __dev_open+0x87/0xe0
[   13.224502]  [<ffffffff8152650c>] __dev_change_flags+0x9c/0x180
[   13.224505]  [<ffffffff815266a3>] dev_change_flags+0x23/0x70
[   13.224509]  [<ffffffff8158cd68>] devinet_ioctl+0x5b8/0x6a0
[   13.224512]  [<ffffffff8158d5c5>] inet_ioctl+0x75/0x90
[   13.224516]  [<ffffffff8150b38b>] sock_do_ioctl+0x2b/0x70
[   13.224519]  [<ffffffff8150b681>] sock_ioctl+0x71/0x2a0
[   13.224523]  [<ffffffff8114ed47>] do_vfs_ioctl+0x87/0x520
[   13.224528]  [<ffffffff8113f159>] ? ____fput+0x9/0x10
[   13.224533]  [<ffffffff8106228c>] ? task_work_run+0x9c/0xd0
[   13.224537]  [<ffffffff8114f271>] SyS_ioctl+0x91/0xb0
[   13.224541]  [<ffffffff816aa252>] system_call_fastpath+0x16/0x1b

Cc: <stable@vger.kernel.org> # 3.11.x
Cc: Tod Jackson <tod.jackson@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes the bcma_core_pci_power_save() call from
the bcma_core_pci_{up,down}() functions as it tries to schedule
thus requiring to call them from non-atomic context. The function
bcma_core_pci_power_save() is now exported so the calling module
can explicitly use it in non-atomic context. This fixes the
'scheduling while atomic' issue reported by Tod Jackson and
Joe Perches.

[   13.210710] BUG: scheduling while atomic: dhcpcd/1800/0x00000202
[   13.210718] Modules linked in: brcmsmac nouveau coretemp kvm_intel kvm cordic brcmutil bcma dell_wmi atl1c ttm mxm_wmi wmi
[   13.210756] CPU: 2 PID: 1800 Comm: dhcpcd Not tainted 3.11.0-wl #1
[   13.210762] Hardware name: Alienware M11x R2/M11x R2, BIOS A04 11/23/2010
[   13.210767]  ffff880177c92c40 ffff880170fd1948 ffffffff8169af5b 0000000000000007
[   13.210777]  ffff880170fd1ab0 ffff880170fd1958 ffffffff81697ee2 ffff880170fd19d8
[   13.210785]  ffffffff816a19f5 00000000000f4240 000000000000d080 ffff880170fd1fd8
[   13.210794] Call Trace:
[   13.210813]  [<ffffffff8169af5b>] dump_stack+0x4f/0x84
[   13.210826]  [<ffffffff81697ee2>] __schedule_bug+0x43/0x51
[   13.210837]  [<ffffffff816a19f5>] __schedule+0x6e5/0x810
[   13.210845]  [<ffffffff816a1c34>] schedule+0x24/0x70
[   13.210855]  [<ffffffff816a04fc>] schedule_hrtimeout_range_clock+0x10c/0x150
[   13.210867]  [<ffffffff810684e0>] ? update_rmtp+0x60/0x60
[   13.210877]  [<ffffffff8106915f>] ? hrtimer_start_range_ns+0xf/0x20
[   13.210887]  [<ffffffff816a054e>] schedule_hrtimeout_range+0xe/0x10
[   13.210897]  [<ffffffff8104f6fb>] usleep_range+0x3b/0x40
[   13.210910]  [<ffffffffa00371af>] bcma_pcie_mdio_set_phy.isra.3+0x4f/0x80 [bcma]
[   13.210921]  [<ffffffffa003729f>] bcma_pcie_mdio_write.isra.4+0xbf/0xd0 [bcma]
[   13.210932]  [<ffffffffa0037498>] bcma_pcie_mdio_writeread.isra.6.constprop.13+0x18/0x30 [bcma]
[   13.210942]  [<ffffffffa00374ee>] bcma_core_pci_power_save+0x3e/0x80 [bcma]
[   13.210953]  [<ffffffffa003765d>] bcma_core_pci_up+0x2d/0x60 [bcma]
[   13.210975]  [<ffffffffa03dc17c>] brcms_c_up+0xfc/0x430 [brcmsmac]
[   13.210989]  [<ffffffffa03d1a7d>] brcms_up+0x1d/0x20 [brcmsmac]
[   13.211003]  [<ffffffffa03d2498>] brcms_ops_start+0x298/0x340 [brcmsmac]
[   13.211020]  [<ffffffff81600a12>] ? cfg80211_netdev_notifier_call+0xd2/0x5f0
[   13.211030]  [<ffffffff815fa53d>] ? packet_notifier+0xad/0x1d0
[   13.211064]  [<ffffffff81656e75>] ieee80211_do_open+0x325/0xf80
[   13.211076]  [<ffffffff8106ac09>] ? __raw_notifier_call_chain+0x9/0x10
[   13.211086]  [<ffffffff81657b41>] ieee80211_open+0x71/0x80
[   13.211101]  [<ffffffff81526267>] __dev_open+0x87/0xe0
[   13.211109]  [<ffffffff8152650c>] __dev_change_flags+0x9c/0x180
[   13.211117]  [<ffffffff815266a3>] dev_change_flags+0x23/0x70
[   13.211127]  [<ffffffff8158cd68>] devinet_ioctl+0x5b8/0x6a0
[   13.211136]  [<ffffffff8158d5c5>] inet_ioctl+0x75/0x90
[   13.211147]  [<ffffffff8150b38b>] sock_do_ioctl+0x2b/0x70
[   13.211155]  [<ffffffff8150b681>] sock_ioctl+0x71/0x2a0
[   13.211169]  [<ffffffff8114ed47>] do_vfs_ioctl+0x87/0x520
[   13.211180]  [<ffffffff8113f159>] ? ____fput+0x9/0x10
[   13.211198]  [<ffffffff8106228c>] ? task_work_run+0x9c/0xd0
[   13.211202]  [<ffffffff8114f271>] SyS_ioctl+0x91/0xb0
[   13.211208]  [<ffffffff816aa252>] system_call_fastpath+0x16/0x1b
[   13.211217] NOHZ: local_softirq_pending 202

The issue was introduced in v3.11 kernel by following commit:

commit aa51e598
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date:   Sat Aug 24 00:32:31 2013 +0200

    brcmsmac: use bcma PCIe up and down functions

    replace the calls to bcma_core_pci_extend_L1timer() by calls to the
    newly introduced bcma_core_pci_ip() and bcma_core_pci_down()
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
    Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fix has been discussed with Hauke Mehrtens [1] selection
option 3) and is intended for v3.12.

Ref:
[1] http://mid.gmane.org/5239B12D.3040206@hauke-m.de

Cc: <stable@vger.kernel.org> # 3.11.x
Cc: Tod Jackson <tod.jackson@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver uses platform_driver_probe() to obtain platform data
if any. However, that function is placed in the .init section so
it must be called upon driver module initialization.

The problem was reported by Fenguang Wu resulting in a kernel
oops because the .init section was already freed.

[   48.966342] Switched to clocksource tsc
[   48.970002] kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
[   48.970851] BUG: unable to handle kernel paging request at ffffffff82196446
[   48.970957] IP: [<ffffffff82196446>] classes_init+0x26/0x26
[   48.970957] PGD 1e76067 PUD 1e77063 PMD f388063 PTE 8000000002196163
[   48.970957] Oops: 0011 [#1]
[   48.970957] CPU: 0 PID: 17 Comm: kworker/0:1 Not tainted 3.11.0-rc7-00444-gc52dd7f #23
[   48.970957] Workqueue: events brcmf_driver_init
[   48.970957] task: ffff8800001d2000 ti: ffff8800001d4000 task.ti: ffff8800001d4000
[   48.970957] RIP: 0010:[<ffffffff82196446>]  [<ffffffff82196446>] classes_init+0x26/0x26
[   48.970957] RSP: 0000:ffff8800001d5d40  EFLAGS: 00000286
[   48.970957] RAX: 0000000000000001 RBX: ffffffff820c5620 RCX: 0000000000000000
[   48.970957] RDX: 0000000000000001 RSI: ffffffff816f7380 RDI: ffffffff820c56c0
[   48.970957] RBP: ffff8800001d5d50 R08: ffff8800001d2508 R09: 0000000000000002
[   48.970957] R10: 0000000000000000 R11: 0001f7ce298c5620 R12: ffff8800001c76b0
[   48.970957] R13: ffffffff81e91d40 R14: 0000000000000000 R15: ffff88000e0ce300
[   48.970957] FS:  0000000000000000(0000) GS:ffffffff81e84000(0000) knlGS:0000000000000000
[   48.970957] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[   48.970957] CR2: ffffffff82196446 CR3: 0000000001e75000 CR4: 00000000000006b0
[   48.970957] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   48.970957] DR3: 0000000000000000 DR6: 0000000000000000 DR7: 0000000000000000
[   48.970957] Stack:
[   48.970957]  ffffffff816f7df8 ffffffff820c5620 ffff8800001d5d60 ffffffff816eeec9
[   48.970957]  ffff8800001d5de0 ffffffff81073dc5 ffffffff81073d68 ffff8800001d5db8
[   48.970957]  0000000000000086 ffffffff820c5620 ffffffff824f7fd0 0000000000000000
[   48.970957] Call Trace:
[   48.970957]  [<ffffffff816f7df8>] ? brcmf_sdio_init+0x18/0x70
[   48.970957]  [<ffffffff816eeec9>] brcmf_driver_init+0x9/0x10
[   48.970957]  [<ffffffff81073dc5>] process_one_work+0x1d5/0x480
[   48.970957]  [<ffffffff81073d68>] ? process_one_work+0x178/0x480
[   48.970957]  [<ffffffff81074188>] worker_thread+0x118/0x3a0
[   48.970957]  [<ffffffff81074070>] ? process_one_work+0x480/0x480
[   48.970957]  [<ffffffff8107aa17>] kthread+0xe7/0xf0
[   48.970957]  [<ffffffff810829f7>] ? finish_task_switch.constprop.57+0x37/0xd0
[   48.970957]  [<ffffffff8107a930>] ? __kthread_parkme+0x80/0x80
[   48.970957]  [<ffffffff81a6923a>] ret_from_fork+0x7a/0xb0
[   48.970957]  [<ffffffff8107a930>] ? __kthread_parkme+0x80/0x80
[   48.970957] Code: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
cc cc cc cc cc cc <cc> cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
[   48.970957] RIP  [<ffffffff82196446>] classes_init+0x26/0x26
[   48.970957]  RSP <ffff8800001d5d40>
[   48.970957] CR2: ffffffff82196446
[   48.970957] ---[ end trace 62980817cd525f14 ]---

Cc: <stable@vger.kernel.org> # 3.10.x, 3.11.x
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Tested-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bug 60815 - Interface hangs in mwifiex_usb
https://bugzilla.kernel.org/show_bug.cgi?id=60815

[ 2.883807] BUG: unable to handle kernel NULL pointer dereference
            at 0000000000000048
[ 2.883813] IP: [<ffffffff815a65e0>] pfifo_fast_enqueue+0x90/0x90

[ 2.883834] CPU: 1 PID: 3220 Comm: kworker/u8:90 Not tainted
            3.11.1-monotone-l0 #6
[ 2.883834] Hardware name: Microsoft Corporation Surface with
            Windows 8 Pro/Surface with Windows 8 Pro,
            BIOS 1.03.0450 03/29/2013

On Surface Pro, suspend to ram gives a NULL pointer dereference in
pfifo_fast_enqueue(). The stack trace reveals that the offending
call is clearing carrier in mwifiex_usb suspend handler.

Since commit 1499d9fa "mwifiex: don't drop carrier flag over suspend"
has removed the carrier flag handling over suspend/resume in SDIO
and PCIe drivers, I'm removing it in USB driver too. This also fixes
the bug for Surface Pro.

Cc: <stable@vger.kernel.org> # 3.5+
Tested-by: NDmitry Khromov <icechrome@gmail.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bug 60815 - Interface hangs in mwifiex_usb
https://bugzilla.kernel.org/show_bug.cgi?id=60815

We have 4 bytes of interface header for packets delivered to SDIO
and PCIe, but not for USB interface.

In Tx AMSDU case, currently 4 bytes of garbage data is unnecessarily
appended for USB packets. This sometimes leads to a firmware hang,
because it may not interpret the data packet correctly.

Problem is fixed by removing this redundant headroom for USB.

Cc: <stable@vger.kernel.org> # 3.5+
Tested-by: NDmitry Khromov <icechrome@gmail.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added USB ID for Corega WLUSB2GTST USB adapter.

Cc: <stable@vger.kernel.org>
Reported-by: NJoerg Kalisch <the_force@gmx.de>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This supercedes the older patch ("cw1200: Don't perform SPI transfers in
interrupt context") that badly attempted to fix this problem.

This is a far simpler solution, which has the added benefit of
actually working.
Signed-off-by: NSolomon Peachy <pizza@shaftnet.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit aec8e88c.

This solution turned out to cause interrupt delivery problems, and
rather than trying to fix this approach, it has been scrapped in favor
of an alternative (and far simpler) implementation.
Signed-off-by: NSolomon Peachy <pizza@shaftnet.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For pcie8897, the hs_cfg cancel command (0xe5) times out when host
comes out of suspend. This is caused by an incompleted host sleep
handshake between driver and firmware.

Like SDIO interface, PCIe also needs to go through firmware power
save events to complete the handshake for host sleep configuration.
Only USB interface doesn't require power save events for hs_cfg.

Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The private array at the end of the rtl_priv struct is not aligned.
On ARM architecture, this causes an alignment trap and is fixed by aligning
that array with __align(sizeof(void *)). That should properly align that
space according to the requirements of all architectures.
Reported-by: NJason Andrews <jasona@cadence.com>
Tested-by: NJason Andrews <jasona@cadence.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Prevents race conditions when un-aggregated frames are pending in the
driver.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If request_firmware_nowait() fails in p54u_load_firmware(),
p54u_load_firmware_cb is not called and no one decrements usb_dev refcnt.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When .release_buffered_frames was implemented, only A-MPDU packets were
buffered internally. Now that this has changed, the BUF_AMPDU flag needs
to be checked before calling ath_tx_addto_baw
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k: Optimize LNA check" tried
to use the "rs_firstaggr" flag to optimize the LNA
combining algorithm when processing subframes in
an A-MPDU. This doesn't appear to work well in practice,
so revert it and use the old method of relying on
"rs_moreaggr".

Cc: stable@vger.kernel.org # 3.11
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This might trip up tx completion processing, although the condition that
triggers this should not (yet) occur in practice.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixes a regression from commit
"ath9k: shrink a few data structures by reordering fields"

When cloning a buffer, the stale flag (part of bf_state now) needs to be
reset after copying the state to prevent tx processing hangs.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the following scenario the socket is corked:
If the first UDP packet is larger then the mtu we try to append it to the
write queue via ip6_ufo_append_data. A following packet, which is smaller
than the mtu would be appended to the already queued up gso-skb via
plain ip6_append_data. This causes random memory corruptions.

In ip6_ufo_append_data we also have to be careful to not queue up the
same skb multiple times. So setup the gso frame only when no first skb
is available.

This also fixes a shortcoming where we add the current packet's length to
cork->length but return early because of a packet > mtu with dontfrag set
(instead of sutracting it again).

Found with trinity.

Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: NDmitry Vyukov <dvyukov@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also changed a log message to indicate that memory was not allocated
instead of memory not available!
Signed-off-by: NMalahal Naineni <malahal@us.ibm.com>
Acked-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In my patch c194992c ("skge: fix
broken driver") I didn't fix the skge bug correctly. The value of the
new mapping (not old) was passed to pci_unmap_single.

If we enable CONFIG_DMA_API_DEBUG, it results in this warning:
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:986 check_sync+0x4c4/0x580()
skge 0000:02:07.0: DMA-API: device driver tries to sync DMA memory it has
not allocated [device address=0x000000023a0096c0] [size=1536 bytes]

This patch makes the skge driver pass the correct value to
pci_unmap_single and fixes the warning. It copies the old descriptor to
on-stack variable "ee" and unmaps it if mapping of the new descriptor
succeeded.

This patch should be backported to 3.11-stable.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Reported-by: NFrancois Romieu <romieu@fr.zoreil.com>
Tested-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Redirect isn't an error condition, it should leave
the error handler without touching the socket.
Signed-off-by: NDuan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Redirect isn't an error condition, it should leave
the error handler without touching the socket.
Signed-off-by: NDuan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MRP doesn't implement the periodictimer in 802.1Q, so it never retries
if packets get lost.  I ran into this problem when MRP sent a MVRP
JoinIn before the interface was fully up.  The JoinIn was lost, MRP
didn't retry, and MVRP registration failed.

Tested against Juniper QFabric switches
Signed-off-by: NNoel Burton-Krahn <noel@burton-krahn.com>
Acked-by: NDavid Ward <david.ward@ll.mit.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Actually re-send packets when the T1 timer runs out. This fixes a bug
where packets are waiting on the write queue until disconnection when
no other traffic is outstanding.
Signed-off-by: NJosselin Costanzi <josselin.costanzi@mobile-devices.fr>
Signed-off-by: NMaxime Jayat <maxime.jayat@mobile-devices.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add generic rule on encountering Belkin bluetooth usb device F8065bf.

Relevant section from /sys/kernel/debug/usb/devices:

T:  Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=050d ProdID=065a Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=0002723E2D29
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
Signed-off-by: NKen O'Brien <kernel@kenobrien.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Yuval Mintz says:

====================
This patch contains various bug fixes, half of which are SR-IOV related
(some fixing issues in the recently added VF RSS support), while the other fix
a wide assortments of issues in the driver.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>